Craftsman 13953776 Owner’s Manual

TOUCH CODE TRANSMITTER MODEL 139.53776

OWNERS MANUAL

FCC. rules prohibit adfustments to or modification of receiver and transmitter circuitry except for changing the code setting
and replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Manufactured under" 1 _ m_e of the following U S. patents: RE29,.525; 4,037",201; 4,750,118; 4,806,930

FEATURES OF THE TOUCH CODE TRANSMITTER

Personalized Code: Upto 10,000 possible combinations,
Code can easily be changed if desired.

Operation: Opener activates when programmed code is
keyed into transmitter and ENTER button is pressed,

The user has 10 seconds to key in the 4-digit code and

press the ENTER button.

tf wrong numbers are accidentally pressed, correction can
be made immediately. The ENTER key will transmit only
the last four digits°

This transmitter can be used with any 5B000SR Series
garage door opener and/or Light Control.

INSTALL TRANSMITTER

Open the transmitter cover and remove the battery compartment screw. Set cover aside and remove battery. NOTE BATTERY

POLARITY AS MARKED ON COMPARTMENT Follow the mounting instructions which apply to your type of door as
described below.

NOTE: If you want the transmitter' in a location different from the one illustrated, it is recommended that you program
the code into the receiver and test the operation of the transmitter before mounting it. A metal door, foil-backed insula-
lion or aluminum siding will lessen transmission range.

SECTIONAL DOOR INSTALLATION: Center the trans-

mitter on garage jamb face at eye level as shown (Figure 1).

Hold the transmitter firmly against jamb with cover half open
so both top and bottom mounting holes are visible_ Use a
punch to mark each hole.Drill two 1/8" pilot holes, Fasten
transmitter securely with screws provided.

insert the plug provided into top hoTe to cover the fastening
screw. Wl'len installing the battery, be sure to observe
polarity (refer to illustration), Re-fasten compartment

cover.

Keypad will Illuminate for 10 seconds at the first push of

ANY number key,

Keypad will remain illuminated for 20 seconds after code
is transmitted° During that time you can STOP or

REVERSE door travel just by pressing the ENTER key.
Power Supply: 12Volt battery.

Installation: Simple to install, Fastening screws and plug
are provided_

All 53000SR Sedes Receivers have two memory channels;
one for the Touch Code Transmitter and the other for all

portable transmitters used to operate an opener or to turn

on lights.

ON_=-PIECE DOOR INSTALLATION: Install the
transmitter on exterior front wall of a FRAME garage. Be sure

to position it away from the door opening to avoid injury as
door swings out and up (Figure 2). NOTE: If the garage is

constructed of material other than wood (brick, stone or
aluminum siding), install transmitter on door jamb with
this important exception: LOCATE TRANSMITTER ON

OUTSIDE EDGE OF DOOR JAMB TO AVOID INJURY AS
DOOR SWINGS OUT AND UP.

Mark fastening holes, drilt and install the transmitter as
instructed for sectional door_ NOTE BATTERY POLARITY.

Keyboard

FIGURE t

FIGURE 2

Garage

!

b

Side 1

SETTING THE CODE

1. Open the Touch C.odeTransmitter cover to access the key-
pad. Decide on a 4-digit code number using numbers from

0 to 9. You can use a number more than once. (For
example, 4, 0, 4, 1).

2o Press the 'SR' code button on the opener panel. The

indicator light atongside the push button will turn ON.

3_ STAND AWAY FROM THE DOOR. Press the selected code

numbers on the keypad and then press the ENTER key.
The indicator light on the opener panel wiil turn OFF and

the door witl begin to move, The opener receiver has been ._
programmed with your code selection. (_

NOTE 1" If the indicator light turns OFF before the code _ . "_ _'
digits and ENTER key are pressed, repeat Steps 2 and 3. _._t,_-_ J t_

NOTE 2' During programming, be sure the,k/_ca_i_n push :---'-"_"
button (if your opener has that feature) is OFF and the

Infrared Sensor (if you have installed that accessory) is

free of obstruction. THE DOOR WILL NOT MOVE AND THE

INDICATOR LIGHT WILL NOT TURN OFF in either case.

To change your code at any time, repeat Steps 1, 2 and 3.

BATTERY: The 12 Volt battery should produce power for at
least one year. As long as there is adequate power, the key-

pad will illuminate and receiver will operate when code and
ENTER keys are pressed.

Replace the battery when keypad illumination becomes dim.

GARAGE DOOR OPENER RECEIVER

0&_ "SR' Code Button)

RED WHT BLK YEL

%

T

"1989, Sears Roebuck & Company

114At155 All Rights Reserved Printed in Mexico