,.odei 139.53758
3-Function Mini Transmitter
EC;,.O.rules prohibit adjustments toor modification of receiver and/or transmitter circuitry except for changing the code setting
and replacing transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Remove the cover screw in NEW transmitter. Turn case over to access code switches #1 through #9. Be careful not
to move circuit board components. Locate code switches in c_iginal transmitter(s), (Refer to illustration)_ Set code switches
in the 3_Function Mini Transmitter to the same positions as code switches in the original transmitter.
NOTE 1: Code switches #2 through #g in ALL transmitters used to operate a receiver must be sot to match. (Coda
switch #1 on 8 3-function transmitter Is neutral. Set it to ANY position. It will not affect the code selected.
NOTE 2: If the original transmltter(s) has only 7 or 8 code switches, set code switches #8 and!or #9 to center
(0) position tn new transmitter.
Manufactured under 1or more of the following US. patents: RE29,525; 4,037,201;4,750,118;4.806,930
MATCH THE CODE IN NEW AND EXISTING TRANSMITTERS
3-Function
0:3
Owners Manual
i,ll ii ,i
-.,_ Standard
i
o-_
JJ "0'
REPLACEMENT PARTS: Transmitter Housing Only (No circuit board) - 4tA3592; 12V Battery - 10A14
CHANGE THE CODE IN RECEIVER AND TRANSMITTER(S)
53000SR SERIES
0NITH RECEIVER 'SR' CODE BUTTON)
Garage Door Openers and Light Controls
(illustration A shows a garage door opener receiver)
"1 St_,ndard [I
I" 1 €2-9)
53000 SERIES
(WITH RECEIVER CODE SWITCHES)
Garage Door Openers and Light Controls
(illustration B shows a garage door opener receiver)
Selec_ a traz_rni_ef
pushbuttonIo X
operatereceiver _ t_ wffr °u_ _L
Key Ring Push _ltons
Holder "S_' Indicator ....
CodeButton Light
Make sure all transmitters areset to matching codeswitch
positions as described above.
1o Press the 'SR' code button on your receiver (illt_tra-
tion A). The indicator light wilt turn ONe
2. STAND AWAY FROM DOOR and pressthe transmit-
ter's SELECTED PUSH BUTTON. The indicator light
will turn OFFand door will move.Code in receivernow
matches transmitter(s) code andwill activatewhen the
selected transmitter push button is pressed,
NOTE: I! transmitter push button ts not pressed
within 30 seconds,the Indicator light will turn OFF.
Repeat 1 and 2,
To use the 3-Function Mtnl Transmitter with other
53000SR Serlse receivers: Select another transmitter
pushbutton to operate e Light Controloradditional garage
door opener. Make sure all transmitters used to operate
receiver are set to the same cote (as described above).
Then repeal I and 2.
You can select adifferent transmitter push button tooper-
ate each device.
Push(_ulton Select a
f _ J (+)
Key Ring Push Button to operate
g Holder (O)
12 3 4 _;67 8ii to positJortthe!
I F_D WHT BLK Y_:L
_ PushButton pushbutton
!ltltlMltl
CodeSwitch
#1
transmitter
receiver
codeswitch#1
pushbur_on
Makesure alltransmitters are set to matching code switch
positionsas described above.
1, Select a transmitterpush buttonto operatethereceiver
as shown in Figure 13.
2, Set RECEIVER code switch #1 to match the position
of the transmitter push button selected. Refer to
illustration BeThen set remaining code switches in
receiver to match the transmitter(s) code switch
positions.
NOTE: If the receiverhas only 7 or 8 switches, sot
transmitter switch #8 and/or #g to (0).
Tousethe 3-FuncttonMlnl Transmitterwithother 53000
Series receivers: Set receiver code switch #1 to match
thepositionofanothertransmitterpushbutton. Then set
remaining code switchesto match transmitter(s)code
switches,
Code switches #2 through #9 in all transmitters used
to operate the receiver MUST be set to matching
positions.
IJIIL,I,ll,_,Jll,llJ_Ui
© 19g0, Sears Roebuck & Company
114Al160_._ All RlghfJiReserved Printed In Mexico
Sears Model 139.53758
3-Function Mini Transmitter
REPLACEMENT PARTS:
Transmitter Housing Only (No circuit board)
12V Battery
41A3592
10A14