Page 1
10/100/1000 Mbps Intelligent Redundant Ring
Gigabit Switch with Optional PoE+
CNGE2+2SMS[POE][HO]
HARDENED
The ComNet CNGE2+2SMS[POE][HO] is a four port intelligent switch with light
management functionality. It provides two 10/100/1000Base-T(X) copper ports and
two 100/1000Base-FX SFP* ports. The CNGE2+2SMS[POE][HO] provides exclusive
functionality for easy field deployment including DIP switch based operation of
RSTP for creating redundant network topologies as well as preventing network
video flooding of multicast traffic when used in a linear or star topology. Ports 1
and 2 can optionally supply up to thirty (30) watts of power per port based on the
IEEE 802.3at standard. An optional High Output (HO) version is also available that
can supply up to sixty (60) watts of PoE from ports 1 and 2. This product is fully
compatible with the ComNet exclusive Copperline SFP modules for operation over
extended distance UTP or Coax cable.
FEATURES
› Several features can be enabled with no programming
required:
- RSTP (Rapid Spanning Tree Protocol)
- Multicast Flooding Prevention
- Dual Media Converter Mode
- Dual Redundant SFP Mode
› 10/10 0/1000 Mbps Ethernet
• 2 × 10/100/1000 BASE-T/TX electrical ports
• 2 × 100/1000 BASE-FX SFP ports (individually DIP switch
selectable)
› Electrical ports support Auto-Negotiation for 10Mbps,
100Mbps or 1000Mbps, full duplex or half duplex data.
› SFP Ports support 100 or 1000 Mbps full duplex data
› SFP Ports compatible with CopperLine® CL-SFP modules
› IEEE802.3at Power over Ethernet (PoE+)
› 30W or 60W PoE+ on Ports 1 and 2
› Automatic MDI/MDI-X crossover
› Designed to meet full compliance with the environmental
requirements (ambient operating temperature, mechanical
shock, vibration, humidity with condensation, highline/low-line voltage conditions and transient voltage
protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment.
†
†
FLEXIBILIT Y
› PoE status monitoring & automatic reboot function
› Event notification through SNMP traps and Relay Output
› Voltage transient protection on all power and signal input/
output lines provides protection from power surges and
other voltage transient events.
› RSTP supported
› Redundant AC/DC inputs for uninterrupted operation in the
event of a loss of operating power or a power supply failure
› Supports LLDP (Link Layer Discovery Protocol)
› Supports Jumbo Frames up to 10K Bytes
› SNMP v1/v2c/v3 for secure network management
› Lifetime Warranty
› Made in the USA
2 + 2ALL GIGABIT
30W
†
†
60W
†
APPLICATIONS
› 10/100/1000 Mbps Ethernet
› Perimeter Protection Surveillance Systems
› IP Video
* SFP = Small Form-Factor Pluggable Module
† CNGE2+2SMSPOE or CNGE2+2SMSPOEHO models only
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
Page 2
CNGE2+2SMS[POE][HO]
SPECIFICATIONS
10/100/1000 Mbps Intelligent Redundant Ring
Gigabit Switch with Optional PoE+
Data
Data Interface Ethernet
Data Rate 10/100/1000 Mbps
IEEE 802.3 Compliant
Full Duplex or Half Duplex Electrical Ports/Full
Duplex Optical Port
Electrical CNGE2+2SMSPOE Por ts 1 & 2: 30 W Max
CNGE2+2SMSPOEHO Ports 1 & 2: 60 W Max
Fibers1 SFP Dependent
Connectors
Optical Requires selection of sold-separately SFP
modules. See ComNet data sheet for number
and description of SFP modules.
Serial Micro USB
Contact Terminal Block (PoE Models Only)
Power Terminal Block
Data RJ45
PoE Pin Assignment RJ45 port support s IEEE802.3at
End-point Positive (VCC+): RJ45 pin 1, 2
(RJ45 pin 1,2 and 4,5 on 60W ports)
Negative (VCC-): RJ45 pin 3, 6
(RJ45 pin 3,6 and 7,8 on 60W ports)
LED Indicators - Optical Link/Data Activity
- Electrical Link/Data Activity
- Power - PoE - Management
Power
Operating Voltage Dual 48 to 57 VDC PoE, 9 to 36 VDC
or 24 VAC non PoE
Current Draw 3.5A max, with PoE, 1A w/out PoE
Electrical & Mechanical
Surface Mount Wall or Flat Surface Screw Attachment
Current Protection Automatic Resettable Solid-State Current Limiters
Circuit Board Meets IPC Standard
Size 4.1 × 3.7 × 1.46 in (10.4 × 9.4 × 3.7 cm)
Shipping Weight <2 lbs./0.9 kg
Environmental
MTBF >100,000 hours
Operating Temp -40˚ C to +75˚ C
Storage Temp -40˚ C to +85˚ C
Relative Humidity 0% to 95% (non-condensing)
2
Network Redundancy STP / RSTP
Management
SNMP SNMP V1/2c/3
HTTP Web GUI Configuration Interface
CLI Serial Command Line Interface
Switch Properties
Switching Latency 7 µs
Switching Bandwidth 8 Gbps
MAC Table 1K
Processing Store-and-Forward
Fault Alarm
Form A contacts for local fault event alarming
Relay Output Rated 1A @ 24 VDC, non-resistive loads (PoE
models only)
Software Features
RSTP (IEEE 802.1D/w)
Port Configuration, Status, Statistics, Security
PoE Configuration, Status, Health Check
SNMP
Enable/Disable Ports, MAC based port security
Ethernet Standards
IEEE 802.3 for 10BASE-T
IEEE 802.3u for 100BASE-TX and 100BASE-FX
IEEE 802.3z for 1000BASE-X
IEEE 802.3ab for 1000BASE-T
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
IEEE 802.3at for Power Sourcing Equipment (PSE) and PoE (≤ 30 W per por t)
IEEE 802.3x Flow Control and Back Pressure
[1] Multimode fiber needs to meet or exceed fiber standard ITU-T G.651.
Single mode fiber needs to meet or exceed fiber standard ITU-T G.652
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
Page 3
CNGE2+2SMS[POE][HO]
10/100/1000 Mbps Intelligent Redundant Ring
Gigabit Switch with Optional PoE+
ORDERING INFORMATION
Part Number Description
CN GE2+2S MS 4 Port Gigabit Ethernet Self-managed Switch 2 SFP FX, 2TX
CNGE2+2SMSPOE 4 Port Gigabit Ethernet Self-managed Switch 2 SFP FX, 2TX with 30W of PoE+ power
CNGE2+2SMSPOEHO 4 Port Gigabit Ethernet Self-managed Switch, 2 SFP FX, 2TX with 60W of PoE+ power
Included Accessories DC Plug-in Power Supply, 90-264 VAC, 50-60 Hz (included with CNGE2+2SMS only)
Options Power Supply for PoE Models (Extra charge, consult factory)
User-selection of SFP or CopperLine™ CL-SFP modules (Extra charge, consult factory)
[2] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)
DIN-Rail Mounting Adaptor Plate Kit – With mounting hardware (Optional, order model DINBKT2 or DINBKT4)
NOTE: This product requires a fiber installation with a minimum 30 dB connector return loss. The use of Super Polish Connectors is recommended.
Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J.
In a continuing effort to improve and advance technology, product specifications are subject to change without notice.
TYPICAL APPLICATIONS
1 Gbps Fiber Ring Example
Managed
Switch with
CNGE2+2SMS
with 2 × SFP-6
RSTP
1000FX Fiber
IP
Power Power Power
Network
100 Mbps Legacy Copper Ring
Managed
Switch with
CNGE2+2SMS
with CL-SFP3 and SFP-3
RSTP
100FX Fiber
IP
Power Power Power
Network
1000FX Fiber
CNGE2+2SMSPOE
with 2 × SFP-6
4
3
2
1
4
1000FX Fiber1000FX Fiber
3
2
1
CNGE2+2SMSPOEHO
with 2 × SFP-6
4
3
60W PoE30W PoE
2
1
60W PoE30W PoE
222
111
100FX Coax
CNGE2+2SMSPOE
with 2 × CL-SFP3
4
3
2
1
4
100FX COAX100FX UTP
3
2
1
CNGE2+2SMSPOEHO
with 2 × CL-SFP3
4
3
60W PoE30W PoE
2
1
60W PoE30W PoE
222
111
3 CORPORATE DRIVE
8 TURNBERRY PARK ROAD
© 2015 Communic ation Networ ks. All Right s Reserve d. “ComNet ” and the “ComNe t Logo” are regis tered tra demarks of Comm unication Net works.
|
DANBURY, CONNECTICUT 06810
|
GILDERSOME
|
MORLEY
|
|
USA
T: 203.796.5300
|
LEEDS, UK LS27 7LE
|
F: 203.796.5303
|
T: +44 (0)113 307 6400
|
|
F: +44 (0)113 253 7462
TECH SUPPORT: 1.888.678.9427
|
INFO-EUROPE@COMNET.NET
|
INFO@COMNET.NET
04 Jun 2015
Loading...