INSTALLATION &
OPERATION
MANUAL
MODEL QUAD-X Series
QUADRANT LED BEACON
Contents:
Installation & Mounting 2
Wiring Instructions .......................................................................2
Operation .........................................................................................2
Warranty ............................................................................................4
IMPORTANT:
Read all instructions and warnings before installing and using.
INSTALLER: This manual must be delivered to the end user of this equipment.
Installation & Mounting
Magnetic Mounting:
WARNING!
The magnetic based beacon provides a secure, temporary installation. The beacon should be placed in the center of the roof
where the least amount of curvature occurs. Check the magnet for debris before installation. Any foreign matter can reduce
holding power and scratch the vehicle. The roof surface should be dry and have a dull, not glossy nish. A glossy, highly
waxed surface will reduce the magnet's holding power. When placed, the beacon should adhere rmly. The user should not
attempt to drive with the beacon in place should the unit slide or move easily.
As with any magnetically-mounted warning device, its use on the exterior of a moving vehicle is at the sole
discretion and responsibility of the user.
This magnetic mount product provides a secure, temporary installation in most circucumstances and is recom-
This product contains high intensity LED devices. To prevent eye damage, DO NOT stare ino light beam
mended for stationary use only.
at close range.
This device, when magnetically mounted, is not intended for use on a moving vehicle.
WARNING!
Permanent Mounting:
The permanent mount beacon provides a secure, permanent installation. Remove the magnetic mounting hardware and use
the supplied permanent mount brackets and screws to mount the beacon in the desired location. Wire routing should be taken
into consideration when choosing a mounting location.
Wiring Instructions
All versions of the Quadrant LED Beacon are supplied with a 9' straight cord terminated with a Lighter Plug. The lighter plug
has a push-button switch which serves as both ON/OFF control and Flash Pattern change switch. This plug may be used in
either a 12VDC or 24VDC cigarette lighter outlet; rotate and push with reasonable moderate force to insure the best possible
connection.
Features and Specications
Operating Voltage: 10-30VDC, Reverse Polarity Protected
The use of this or any warning device does not insure that all drivers can or will observe or react to an emergency
warning signal. Never take the right-of-way for granted. It is your responsibility to be sure you can proceed
safely before entering an intersection, driving against trafc, responding at a high rate of speed, or walking on
or around trafc lanes.
The effectiveness of this warning device is highly dependent upon correct mounting and wiring. Read and follow
the manufacturer’s instructions before installing or using this device. The vehicle operator should insure daily that
all features of the device operate correctly. In use, the vehicle operator should insure the projection of the warning
signal is not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or other
obstructions. This equipment is intended for use by authorized personnel only. It is the user’s responsibility to
understand and obey all laws regarding emergency warning devices. The user should check all applicable city,
WARNING!
state and federal laws and regulations.
Code 3 , Inc., assumes no liability for any loss resulting from the use of this warning device.
Proper installation is vital to the performance of this warning device and the safe operation of the emergency
vehicle. It is important to recognize that the operator of the emergency vehicle is under psychological and physiological stress caused by the emergency situation. The warning device should be installed in such a manner as
to: A) Not reduce the output performance of the system, B) Place the controls within convenient reach of the
operator so that he can operate the system without losing eye contact with the roadway.
Emergency warning devices often require high electrical voltages and/or currents. Properly protect and use caution around live electrical connections. Grounding or shorting of electrical connections can cause high current
arcing, which can cause personal injury and/or severe vehicle damage, including re.
PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY
WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THE
PUBLIC.
2
Current:
Default Flash Current (Ave): <2.0 Amps @ 13.8VDC
Operation
Flash Patterns:
The Quadrant LED Beacon is programmed with 19 different ash patterns. Refer the section below for instructions on how to
set the ash pattern.
1 Single ash 75 sim all ash (factory Default)
2 ECE R65 120FPM single ash
3 CA T13 75FPM single ash
4 Double ash 75 sim all ash
5 Swiftash ash 75 sim all ash
6 Quad Flash 75 sim all ash
7 Single Flash 75 center-split
8 Single Flash 75 clockwise
9 Single Flash 75L clockwise
10 NFPA 75FPM Quad Flash
11 Five Flash sim all
12 Modu ash sim all
13 ECE R65 Double Flash
14 125FPM Rotating Flash
15 Single Flash 120 center-split
16 Single Flash 120 clockwise
17 Single Flash 120L clockwise
18 Three Flash 120 sim all ash
19 Cycle Flash
20 OFF (For Reference only. This ash pattern cannot be stored in
the beacon's memory)
Setting the Flash Pattern: To change the ash pattern, depress the push-button switch on the lighter plug for -
- Less than 1 second for the NEXT pattern
- 1 to 3 seconds for the PREVIOUS pattern
- 3 to 5 seconds for the DEFAULT pattern
- Greater than 5 seconds to TURN OFF the beacon
Maintenance:
The beacons are completely sealed units designed to be maintenance free. Refer to the guide below for help
with troubleshooting. Should the unit be diagnosed as malfunctioning, remove unit and replace with a new
beacon.
Problem Probable Cause Remedy
Beacon does not activate a. No power to unit a. Check Lighter Plug for loose
This product contains high intensity LED devices. To prevent eye damage, DO NOT stare
into light beam at close range.
WARNING!
This product contains high intensity LED devices. To prevent eye damage, DO NOT stare ino light beam
at close range.
TROUBLESHOOTING
connection
b. Damaged or shortaged cabling b. Check cables for damage
c. Defective Beacon c. Contact Service Dept.
3
WARRANTY
Code 3, Inc.'s L.E.D. emergency devices are tested and found to be operational at the time of manufacture.
Provided they are installed and operated in accordance with manufacturer's recommendations, Code 3, Inc. guarantees
all parts and components except the lamps to a period of 1 year, LED Lighthead modules to a period of 5 years (unless
otherwise expressed) from the date of purchase or delivery, whichever is later. Units demonstrated to be defective
within the warranty period will be repaired or replaced at the factory service center at no cost.
Use of lamp or other electrical load of a wattage higher than installed or recommended by the factory, or use
of inappropriate or inadequate wiring or circuit protection causes this warranty to become void. Failure or destruction
of the product resulting from abuse or unusual use and/or accidents is not covered by this warranty. Code 3, Inc.
shall in no way be liable for other damages including consequential, indirect or special damages whether loss is due
to negligence or breach of warranty.
CODE 3, INC. MAkES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITHOUT LIMITATION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.
PRODUCT RETURNS
If a product must be returned for repair or replacement*, please contact our factory to obtain a Return
Goods Authorization Number (RGA number) before you ship the product to Code 3, Inc. Write the RGA number
clearly on the package near the mailing label. Be sure you use sufcient packing materials to avoid damage to
the product being returned while in transit.
*Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or
reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products return to sender after the service has been
rendered.
PROBLEMS OR QUESTIONS? CALL OUR TECHNICAL ASSISTANCE HOTLINE (314) 996-2800
WWW.CODE3PSE.COM
Code 3® is a registered trademark of Code 3, Inc., a subsidiary of Public Safety Equipment, Inc.
4
Code 3®, Inc.
10986 N. Warson Road
St. Louis, Missouri 63114-2029—USA
Ph. (314) 426-2700 Fax (314) 426-1337
Part No. T11792 Rev.0 1/2012
©2012 Code 3, Inc
Loading...