Code 3 PSEDRL User Manual
DRL COMPATIBLE
100% SOLID STATE ALTERNATING ELECTRONIC FLASHER
COMPATIBLE WITH DAYTIME RUNNING LIGHTS
PSEDRL
Code 3 PSEDRL Solid State Flasher will operate a two or four
headlight system on any vehicle with a 12 Vdc negative ground
system.
NOTE
Please contact Code 3 before attempting to
install on any foreign vehicle (non-General
Motors, Ford or Chrysler).
A properly installed PSEDRL will alternate the vehicle's headlights at 1.9 hertz.
When used at night, the low beam head lights remain ON for
proper illumination while the high beams flash to gain attention and increase the vehicle's visibility. When the dimmer
switch is activated to high beam, the Flasher Systems "High
Beam Override" interrupts the Flasher sequence to allow for
normal high beam function. Flashing automatically resumes
when the dimmer switch is deactivated. The Flasher will automatically turn OFF the vehicle's DRL when the Flasher is activated.
INSTALLATION
MOUNTING: Mount the Flasher so that the maximum amount
of air will flow across it, typically in the front passenger side of
the engine compartment.
[DRIVER SIDE]
LOW
RED
HIGH BEAM WIRE
LOW BEAM WIRE
FUSE
CONTROL
SWITCH
TO
BATTERY
PLUS
WHITE
ORANGE
X X
•
CUT
•
HIGH
BLUE
SOLID STATE
FLASHER
ORANGE
VEHICLE'S
DRL WIRE
•
X
CUT
[PASSENGER SIDE]
X
•
HIGH
YELLOW
BLACK
WHITE/RED
PINK
GREEN
OVERRIDE
(optional)
LOW
TO MARKER
LIGHT WIRE
(optional)
DRL
IGNITION
RUN WIRE
GREEN WIRE: Connect to a convenient reliable ground.
NOTE
Always connect the green wire FIRST when
installing and disconnect LAST when
removing.
BLUE & YELLOW WIRE: Locate the wire that supplies power
to the passenger side high beam headlights. Cut this wire
approximately 10" to 12" from the back of the headlight. Connect the yellow wire to the lead that returns to the passenger
side high beam. Connect the blue wire to the other piece of
cut wire. This will make the driver's side high beam flash.
RED WIRE: Connect to a powered switch. This switch will
only require 1/4 amp to activate the Flasher.
Wiring Schematic
WHITE WIRE: Connect through a fuse to the positive post of
the battery or other high current power source. A 20 amp fuse
to be used with a two headlight system and a 30 amp on a
four headlight system.
WARNING
DO NOT CONNECT THE FLASHER
SYSTEM TO A CIRCUIT BREAKER OR
FUSIBLE LINK.
NOTE
DO NOT connect the red and white wires
together. The white wire must receive a
constant source of power at all times.
WHITE / RED WIRE: "T" or tap into the vehicle's wire that
becomes HOT when the vehicle is started and COLD when
the vehicle is turned off.
ORANGE WIRE(S): Find the DRL input or output wire, see
Wiring Schematic. "T" or tap both orange wires into it. Cut
the wire between the two orange wires and tape.
BLACK WIRE (optional): If an automatic night time cutoff is
required, simply "T" or tap black wire into the vehicle's marker
light wire. If not required, connect to ground.
PINK WIRE (optional): Connect to the HOT side of a user
supplied switch, the park brake switch or the neutral safety
switch. When the pink wire is grounded through one of the
switches, the DRL function and marker lights will be deactivated.
Located under LH side of I/P,
taped on I/P Harness.
DRL
MODULE
FLASHER ORANGE
FLASHER ORANGE
LG/BK
•
X
CUT
X
•
LT.GRN/BLK
FUSE
# 15
DRL
DIODES
ORANGE
DRL
RELAY
FUSE
# 4
PINK
I/P FUSE
BLOCK
FUSE #3 IN 1996 LUMINA
•
FUSE #33 IN 1997 AND NEWER LUMINA
•
FLASHER ORANGE
•
X
CUT
X
FLASHER ORANGE
•
DRL
MODULE
Fuse located in Instrument Panel fuse block. Instrument panel fuse
block is located on right side of dash, between dash and Passenger
door. To gain access to wires in back of fuse block, pull back fuse
panel retaining clip, located on right side of fuse block assembly.
Rotate fuse block so that it can be removed through the fuse block
hole.
Lumina 1996 and Newer
FLASHER ORANGE WIRES
DIMMER
LOW
•
HIGH
XX
•
•
CUT
Connect the Flasher's orange wires
close to the DRL Module.
Ford 1992 and Newer
DRL
MODULE
LT. GRN/BLK
NOTE
Located under LH side of I/P, lower
center of convenience center.
1996 and Newer Suburban, Tahoe,
1500, 2500 and 3500 Pickup Trucks
DRL Module and DRL diodes are
located behind LH side of instrument
panel, on the Electronic Brake
Control Module Bracket.
DK. BLUE
DRL
DIODES
TO LOW BEAM
HEADLAMPS
FLASHER ORANGE
FLASHER ORANGE
DRL
MODULE
•
X
CUT
X
•
1996 and Newer Pontiac GrandAm, Grand Prix,
Buick Regal, Oldsmobile Cutlass Supreme
and Monte Carlo.
1992 - 1994 Crown Victoria: DRL Module located center
front of vehicle on the front upper radiator support.
1995 and Newer Crown Victoria: DRL Module located on
the upper radiator support just left of center of vehicle.
1995 and Older T aurus: DRL Module located on LH fender
apron directly under battery .
1996 and Newer T aurus: DRL Module located on LH front
bumper brace under the front of vehicle.
1996 and Older F-Series Truck: DRL Module located on LH
radiator support.
1997 and Newer F-Series Truck: DRL Module located on
radiator support.
PSEDRL.P65 08/01
Loading...