INSTALLATION
& OWNERS
MANUAL
REMOTE
CONTROLLED
SPOTLIGHT
NIGHTPROBE
IN LIGHTBAR
Introduction
The NightProbe , NP 130, product can be mounted in the center section of a Code 360, Excalibur or MX
lightbar. This offers the user an unobstructed 360 degrees of light around the vehicle.
Installation & Mounting
1. Install the circular gasket on the upper surface of the lens cover and spacer.
2. Route the cables from the bottom of the spotlight through the gasket, lens cover as shown in
Figure 2.
3. Place the other two spacers on the lens cover. They will be sandwiched between the lens cover and the
mounting plate.
4. Place the mounting plate over the spacers, align the holes in the mounting plate with the holes in the lens
cover.
5. Attach the spotlight with four #6x3/4” screws to the mounting plate.
6. Remove the center lens of the lightbar and keep the four lens clips for reuse.
7. Route the cables through the existing hole in the bottom of the lightbar, insure that there is adequate
length to reach the area in which the controller is to be mounted.
8. Install the spotlight mounting bracket to the lightbar frame using eight #8 x .270” screws. The bracket
should fit snugly between the plastic ribs of the lower lens to ensure alignment with the lens/mtg plate
assy.
9. Install the spotlight and lens/mtg plate to the lower lens being careful not to pinch the cables. Fasten with
four #14 x 3/4” washer seal screws.
10. Reinstall the four lens clips.
11. Connect the wiring and the control box per instructions with the spotlight.
®
Figure 2
Shown separated for clarity (actual assembly
is sealed together with caulk/adhesive)
Parts List
Ref No. Description Part No. Qty.
1 Spotlight -Complete S50597 01
2 Gasket, .062 thk foam, RE41E black T05084 01
3 Cover S96255 01
4 Fastener #14x3/4 with washer seal T05070 06
5 Fastener #6x3/4 T01031 04
6 Fastener #8x.270 T01215 08
7 Spotlight mounting bracket (Code 360/Excalibur) S50795 01
MX S50593 01
8 Spacer, Spotlight in lightbar S96254 03
9 Mounting Plate S50796 01
!
WARNING!
The use of this or any warning device does not ensure that all drivers can or will observe or
react to an emergency warning signal. Never take the right-of-way for granted. It is your
responsibility to be sure you can proceed safely before entering an intersection, driving
against traffic, responding at a high rate of speed, or walking on or around traffic lanes.
The effectiveness of this warning device is highly dependent upon correct mounting and
wiring. Read and follow the manufacturer’s instructions before installing or using this
device. The vehicle operator should insure daily that all features of the device operate
correctly. In use, the vehicle operator should insure the projection of the warning signal is
not blocked by vehicle components (i.e.: open trunks or compartment doors), people,
vehicles, or other obstructions.
This equipment is intended for use by authorized personnel only. It is the user’s responsibility to understand and obey all laws regarding emergency warning devices. The user
should check all applicable city, state and federal laws and regulations.
Public Safety Equipment, Inc., assumes no liability for any loss resulting from the use of this
warning device.
Proper installation is vital to the performance of this warning device and the safe operation
of the emergency vehicle. It is important to recognize that the operator of the emergency
vehicle is under psychological and physiological stress caused by the emergency situation.
The warning device should be installed in such a manner as to: A) Not reduce the output
performance of the system, B) Place the controls within convenient reach of the operator
so that he can operate the system without losing eye contact with the roadway.
Emergency warning devices often require high electrical voltages and/or currents. Properly
protect and use caution around live electrical connections. Grounding or shorting of
electrical connections can cause high current arcing, which can cause personal injury and/
or severe vehicle damage, including fire.
PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER
USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY
OF EMERGENCY PERSONNEL AND THE PUBLIC.
Notes:
WARRANTY
Code 3, Inc. emergency devices are tested and found to be operational at the time of
manufacture. Provided they are installed and operated in accordance with manufacturer's
recommendations, Code 3, Inc. guarantees all parts and components except the lamps to a period
of 1 year (unless otherwise expressed) from the date of purchase or delivery, whichever is later.
Units demonstrated to be defective within the warranty period will be repaired or replaced at the
factory service center at no cost.
Use of lamp or other electrical load of a wattage higher than installed or recommended by the
factory, or use of inappropriate or inadequate wiring or circuit protection causes this warranty to
become void. Failure or destruction of the product resulting from abuse or unusual use and/or
accidents is not covered by this warranty. Code 3, Inc. shall in no way be liable for other damages
including consequential, indirect or special damages whether loss is due to negligence or breach
of warranty.
CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING,
WITHOUT LIMITATION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH
RESPECT TO THIS PRODUCT.
PRODUCT RETURNS
If a product must be returned for repair or replacement*, please contact our factory to
obtain a Return Goods Authorization Number (RGA number) before you ship the product to
Code 3. Write the RGA number clearly on the package near the mailing label. Be sure you use
sufficient packing materials to avoid damage to the product being returned while in transit.
*Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for
the removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of
products return to sender after the service has been rendered.
NEED HELP? Call our Technical Assistance Hotline - (314) 996-2800
St. Louis, Missouri 63114-2029—USA
10986 N. Warson Road
www.code3pse.com
Code 3, Inc.
Revision 2, 03/2006 - Instruction Book Part No. T05083
NightProbe and Code 3 are registered trademarks of Code 3, Inc. a subsidiary of Public Safety Equipment, Inc.
©2002-6 Code 3, Inc. Printed in USA
Loading...