Code 3 NightProbe Controller Cable User Manual

NIGHTPROBETM Spotlight Control Module

for RLS, Model 3999 Siren System

DESCRIPTION:

The RLS Spotlight Control Module allows use of the RLS 3999 Siren Control to provide full control of the
NIGHTPROBETM spotlight with linear acceleration from stop to full
speed.

OPERATION:

The RLS Spotlight Control Module is controlled by RLS 3999 control
unit, using the SPOT mode and the special function keys. Using the
control unit’s SELECT switch select the SPOT mode. In this mode,
depressing and holding the LEFT, RIGHT, UP or DOWN keys will
cause the NIGHTPROBETM to rotate in the appropriate direction. The
spotlight will accelerate from it’s slowest speed to full speed over a two
second period and stop instantly when the switch is released. This
allows for very precise positioning of the light. Depressing and releas­ing the center switch while in the SPOT mode will cause the lamp to toggle ON and OFF.

WIRING:

Connect the spotlight to +12VDC and Ground as described in the NIGHTPROBETM User Manual. Remove the
cover from the RLS Spotlight Control Module and plug the NIGHTPROBETM control cable into the 7-pin polar­ized header on the circuit board. Replace the cover and mount the RLS Spotlight Control Module near your
RLS siren amplifier.

The control signal originates in the RLS Control Unit and is connected to the RLS system components via a
standard six conductor modular cable. Plug this modular cable into one of the modular jacks on the Spotlight
Control Module. Plug one end of the special twelve inch modular cable (p/n 10937*) provided with the Spot­light Control Module into the remaining modular jack and plug the other end of this cable into the modular jack
on the RLS siren amplifier or the optional RLS Auxiliary Relay Module.

TM

p/n 10937

NIGHTPROBE
Control Cable

Polarized Connector

Detail

Please note that modular cable p/n 10937 is a special cable intended for use in interconnecting the
RLS Spotlight Control Module, RLS Auxiliary Relay Module with the RLS Siren Amplifier. DO NOT use
a standard telephone cable in place of p/n 10937. Please refer to the RLS Siren and NIGHTPROBE

TM

Remote Controlled Spotlight, User Manual for detailed instructions and further cautionary information
on the installation and wiring of the RLS Siren and NIGHTPROBETM Spotlight systems.

WARRANTY

Code 3, Inc.'s emergency devices are tested and found to be operational at the time of
manufacture. Provided they are installed and operated in accordance with manufacturer's
recommendations, Code 3, Inc. guarantees all parts and components except the lamps to a period
of 1 year (unless otherwise expressed) from the date of purchase or delivery, whichever is later.
Units demonstrated to be defective within the warranty period will be repaired or replaced at the
factory service center at no cost.

Use of lamp or other electrical load of a wattage higher than installed or recommended by
the factory, or use of inappropriate or inadequate wiring or circuit protection causes this warranty
to become void. Failure or destruction of the product resulting from abuse or unusual use and/
or accidents is not covered by this warranty. Code 3, Inc. shall in no way be liable for other
damages including consequential, indirect or special damages whether loss is due to negligence
or breach of warranty.

CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING,
WITHOUT LIMITATION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH
RESPECT TO THIS PRODUCT.

PRODUCT RETURNS

If a product must be returned for repair or replacement*, please contact our factory to
obtain a Return Goods Authorization Number (RGA number) before you ship the product to
Code 3, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you
use sufficient packing materials to avoid damage to the product being returned while in transit.

*Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for
the removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of
products return to sender after the service has been rendered.

NEED HELP? Call our Technical Support Hotline - [phone]

St. Louis, Missouri 63114-2029—USA

10986 N. Warson Road

www.code3pse.com

Code 3, Inc.

Nightprobe is a trademark of Code 3, Inc.
Code 3 is a registered trademark of Code 3, Inc. a subsidiary of Public Safety Equipment, Inc.

Revision 2, 12/2005 - Instruction Book Part No. 10938

©2004-5 Code 3, Inc. Printed in USA