Classe Audio CAV-75 User Manual

CLASSÉ AUDIO

CAV-75

MULTI-CHANNEL

POWER AMPLIFIER

CAV-75

OWNER'S MANUAL

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:
Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB
boards etc.), and adjusting many specific operating voltages within proper engineering ranges,
producing an overall sonic recipe giving the most natural harmonic realism of music typical of
instruments in a live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:
All Classé products (all preamps and all amps) share exactly the same circuit (excluding moving
coil and moving magnet phono circuits). This means all amplifiers and all high level circuits of
the preamps are the same. The same circuit is tailored to different power levels etc. Differences
between less expensive models and more expensive models are parts quality and compliment,
power supply extravagance and the amount of filtering etc., as well as features and packaging.
This means that for years Classé has been constantly fine tuning and upgrading this circuit and its
application, thus reaching a very high level of understanding and musical achievement which
benefits all models - least expensive, most expensive, preamps and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:
Choosing the best attainable quality parts and materials combined with the advantages of the two
above-mentioned areas provides Classé owners with years of proven trouble free reliability and
musical enjoyment.

-2-

CAV-75

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP........................................................... 4

GENERAL CONNECTIONS AND OPERATIONS ................. 5

CONNECTIONS AND DIAGRAMS ......................................... 7

WARRANTY ............................................................................. 10

SPECIFICATIONS .................................................................... 12

WARRANTY REGISTRATION ............................................... 14

-3-

UNPACKING & SET-UP

Your Classé CAV-75 multi-channel power amplifier is packed in high density, semi-rigid
foam placed in a special cardboard box. To remove the unit, open and spread all the top flaps of the
box and by its sides, lift out the entire unit and put it on a large flat surface. Take it out of the plastic
bag and inspect the unit for any concealed damage. Apart from this owner's manual, please ensure
the following have also been included:

1) Detachable linecord.

2) Allen key for top plate.
Please report any damage or missing parts to your dealer as soon as possible.
Place the CAV-75 at or near its final set-up position, allowing 8 inches at the rear for
tightening the speaker output connectors. For optimum sonic performance, we recommend the
optional

CLASSÉ REFERENCE A.C. LINECORD

. Consult your dealer regarding this accessory.
The power transformer in the CAV-75 is located at the front-left of the unit. Ideally, a few
feet should separate this area from components which potentially could pick up hum. These
include preamplifiers, turntables, and interconnect cables. In terms of providing adequate airspace
for cooling, a good rule of thumb is to allow 6 inches above and 3 inches on each side of the unit.
Check the Serial Number sticker on th e back of the unit for the correct operating voltage.
The CAV-75 has one line fuse (external), the rating of which should be as follows:

LINE VOLTAGE FUSE RATING
100 or 120 V.A.C. 5 AMP SLOW BLOW 125 or 250 volts
220 or 240 V.A.C. 3 AMP SLOW BLOW 250 volts

4

- -

INTERNAL RAIL FUSES:

The CAV-75 is designed with each channel protected by one pair of internal fuses for
positive and negative rails (see f ig -1 page 7)

4 AMP FAST BLOW 125 volts

GENERAL CONNECTIONS AND OPERATION:

A.C. LINE
Insert the linecord into the A.C. receptacle on the rear of the unit.

CAUTION: SAFE TY INSTRUCTIONS
DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE

GROUND", OR DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE
A SHOCK HAZARD. CONNECT ALL INTERCONNECT CABLES BETWEEN THE
ELECTRONICS BEFORE CONNECTING THE A.C. LINECORDS TO THE WALL
OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE ALSO THE
WARRANTY SECTION OF THIS OWNER'S MANUAL.

NORMAL OPERATION:
Input and output connectors for each channel are clearly grouped and marked on the back of
the amplifier. (Units are preset at the factory for NORMAL.) See fig.3a,3b for typical connections
of the CAV-75.
Use only high quality interconnect and loudspeaker cables, and make all connections tight.
If the input plugs are loose, remove them and pinch down the ground leaves slightly with pliers.
Observe correct phasing of the loudspeaker connections, and tighten.

BRIDGED OPERATION:

5

- -