Classe Audio C-601 Owners manual
CLASSÉ AUDIO
C-601
REMOTE CONTROL
BALANCED PREAMPLIFIER
C-601
OWNER'S MANUAL
CLASSÉ DESIGN PHILOSOPHY
1. REPEATED LISTENING DESIGN SESSIONS:
Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards
etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an
overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a
live performance.
2. UPGRADABLE SINGLE CIRCUIT DESIGNS:
All Classé products (all preamps and all amps) share exactly the same circuit design philosophy
(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high
level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to
different power levels etc. Differences between less expensive models and more expensive models
are parts quality and compliment, power supply extravagance and the amount of filtering etc., as
well as features and packaging.
This means that for years Classé has been constantly sonically fine tuning and technically upgrading
this circuit design and its application, thus reaching a very high level of natural musical enjoyment,
as well as excellent reliability which benefits all models - least expensive, most expensive, preamps
and amplifiers alike.
3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:
Choosing the best attainable quality parts and materials combined with the advantages of the two
above-mentioned areas provides Classé owners with years of proven trouble free reliability and
musical enjoyment.
-3-
C-601
OWNER'S MANUAL
TABLE OF CONTENTS
UNPACKING & SET-UP....................................................... 4
A.C. LINE POWER................................................................. 5
INPUTS.................................................................................... 6
OUTPUTS ............................................................................... 8
FRONT PANEL CONTROLS................................................. 9
FEATURES AND SPECIFICATIONS .................................. 18
-4-
UNPACKING & SET-UP
Your new preamplifier has been carefully wrapped in heavy gauge plastic, packed in semi-rigid
foam and contained in a special box. To remove the unit, open and spread the top flaps of the box. By
its sides, lift out the entire unit with the foam pieces intact. Remove each foam side by pulling straight
out. Remove the plastic wrap and inspect the unit for any concealed damage. Apart from this owner's
manual, please ensure the following has also been included:
1) External power supply.
2) Detachable A.C. linecord.
3) Detachable D.C. power supply cable.
4) 5/64 in. Allen key for top cover
5) Remote Control unit (Allen key and Batteries AAA X 2 included).
Please report any damage or missing parts to your dealer promptly.
This preamplifier, being capable of very high gain, must be located in a position free of any
hum-inducing magnetic fields. (This also applies to turntables and interconnect cables.) Positions
adjacent to power amplifiers, A.C. line filters, or regulation devices should be avoided. Ideally, a few
feet should separate the preamplifier from the power amplifier. As well, keep low-level interconnect
cables away from the power amp and separate from A.C. linecords.
Heat generated by the preamplifier is negligible. Air space around the unit need not be a
concern.
Check the Serial Number sticker on the back of the unit for the correct operating voltage.
Regardless of voltage, the fuse rating should be 2 AMP SLO-BLO.
-5-
A.C. LINE POWER
The preamplifier has no power switch. Its low power consumption and improved sonics from
always being ON led to the omission of an ON/OFF switch. In fact, while thoroughly musical shortly
after turn-on, the preamplifier will exhibit "sonic growth" for the first 300 hours of used.
For optimum sonic performance, you should consider use of the optional CLASSE
REFERENCE A.C. LINECORD. Consult your dealer regarding this accessory.
SAFETY FEATURE: The preamplifier is designed with an Auto-Muting Circuit which engages
and is indicated by two FLASHING RED ARROWS when the unit is first connected, or after an A.C.
power failure. After 45 seconds of stabilizing the preamplifier is automatically switched to "MUTE"
mode, after which all operating functions such as input etc. may then be selected.
CAUTION: "FLOATING THE GROUND” OR DEFEATING THE GROUND ON A 3PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL INTERCONNECT
CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C. LINECORDS TO
THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE ALSO
THE WARRANTY SECTION OF THIS OWNER'S MANUAL.
-6-
INPUTS
The input jacks are clearly marked on the back of the C-601. The following inputs are provided:
BAL 1, BAL 2, REG 1 (also used for Phono), REG 2, REG 3, REG 4, TAPE, and a SURROUND
sound loop. (see figure 3).
OPTIONAL INTERNAL PHONO FEATURE:
The REG 1 input jacks are to be used with the optional phono feature (see fig.6) The phono
ground screw is located between the REG 4 and TAPE IN jacks. The optional phono can accommodate
both magnetic and moving coil cartridges of various outputs. In the MC position, gain of the Moving
Coil stage is factory preset at 16dB which matches perfectly with most typical MC cartridges. With the
resistor kit included with the optional phono feature, the gain can also be adjusted to 20db, 25db, or
30db in order to optimize system gain, and lower noise while using other less typical MC cartridges.
(Note: The MC gain is in addition to the standard MM gain of 42dB). To change the MC gain, proceed
as follows:
1. Disconnect A.C. linecord from the wall outlet.
2. Remove top cover with Allen key supplied.
3. Locate R245 and R145 (see fig.6), which are the MC gain setting resistors for the LEFT and
RIGHT channel respectively. Remove the resistors and replace them with newly selected ones,
according to the following chart.
GAIN COLOR CODED RESISTOR (or) NUMERICAL RESISTOR
Standard: 16db (Brown, Brown, Black, Black) 1100 (110 ohms)
20db (Red, Black, Black, Black) 2000 (200 ohms)
25db (Orange, Grey, Orange, Black) 3830 (383 ohms)
30db (Violet, Blue, Grey, Black) 7680 (768 ohms)
4. Having completed the resistor changes, replace the top cover.
-7-
BALANCED, TAPE, AND REGULAR INPUTS
The BALANCED INPUTS are true differential high level inputs, wired as follows:
PIN 1: GROUND
PIN 2: POSITIVE (NON-INVERTED) SIGNAL
PIN 3: NEGATIVE (INVERTED) SIGNAL
The Balanced inputs may be used with CD players that have a balance output, or any other high
level, balanced source.
The TAPE IN of the C-601 should be connected to the LINE OUT or TAPE OUT of the tape
deck. (See FRONT PANEL CONTROLS: TAPE SWITCH.)
The Regular inputs may be used with any high level sources (REG 1 may also be used with the
optional Classé Internal Phono Feature.)
Loading...