Clarion MSS430 User Manual

SOURCE COMMANDER

MSS430

OWNER’S MANUAL

INSTALLATION GUIDE

MULTISTATION

A/V SELECTOR

RL

V

RL

V

R

L

V

RL

V

OWNER’S MANUAL/INSTALLATION GUIDE

1

WARNING!

THE CLARION MSS430 MULTISTATION A/V SELECTOR IS
DESIGNED FOR SWITCHING OF VIDEO SOURCES FOR REAR
SEAT VIEWING ONLY.

THIS PRODUCT IS NOT INTENDED FOR VIEWING BY THE
DRIVER WHILE THE VEHICLE IS IN MOTION SINCE SUCH USE
MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIV­ER’S SAFE OPERATION OF THE VEHICLE AND MAY RESULT
IN SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIO­LATE STATE LAW.

CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY
INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE
THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED
USES OF THIS PRODUCT.

ABOUT INSTALLATION

Installation of mobile audio and video components requires
experience with a variety of mechanical and electrical proce­dures. Even though this manual provides general installation
and operation instructions for your new Clarion MSS430
Multistation A/V Selector, it does not show the exact installa­tion methods for your particular vehicle.

If you do not have the required knowledge and experience to
successfully complete the installation, we strongly recom­mend consulting an authorized Clarion dealer about profes­sional installation options.

TABLE OF CONTENTS

Introduction...............................................................2

Installation And Operation Precautions......................3

Installation And Wiring .............................................5

Description Of MSS430 Front Connectors .................10

Description Of MSS430 Rear Connectors ..................12

Description Of Control Station..................................13

Applications Input Configurations ............................15

Applications Output Configurations .........................16

Operating the MSS430 ...........................................17

Troubleshooting ......................................................19

Specifications ..........................................................20

FCC Statement .........................................................20

SOURCE COMMANDER MSS430

2

INTRODUCTION

The Clarion MSS430 is a full-featured Multistation A/V
Selector specifically created for the mobile environment.
When used with the enclosed Control Stations, the system
allows true multi-zone control with independent audio/video
selection of up to four sources and connection of up to three
monitors, each capable of displaying a different audio/video
program. Each station provides individual entertainment.

The MSS430 also includes the following features:

• Works with all Clarion monitors

• Accepts up to three individual Control Stations

• All solid-state electronic circuits

• Audio level gain controls

• Buffered input and output audio/video circuits

• Gold-plated RCA connectors

• High-quality video/audio selector circuits

• Rear Vision Camera automatic switching

About The Manual And Warranty

To start enjoying your new Clarion MSS430 Multistation A/V
Selector, please read all remaining instructions listed in this
manual. Keep all instructions for future reference.

This product is covered by a limited warranty (see the
enclosed warranty card). Save the sales receipt to protect

your purchase and aid in warranty service.

OWNER’S MANUAL/INSTALLATION GUIDE

3

INSTALLATION AND OPERATION PRECAUTIONS

Installation Precautions

• This unit operates on an automotive 12-volt negative
ground power source and requires additional mobile audio
and video components for proper operation.

• Before installation, disconnect the (–) negative lead from
the vehicle’s battery.

• Use only supplied screws and hardware. Make sure all
connections and components are fastened securely .

• At the proposed installation sites, make sure there is ade­quate space to accommodate both MSS430 and the
Control Station dimensions.

• Use extreme caution when drilling around electrical
wiring, brake lines, and fuel lines. Check clearances on
both sides of a planned installation surface before drilling
any holes or installing any screws.

• Always wear protective eyewear when using tools.

• Use only high-quality RCA cables that are no longer than
necessary for direct connections to other components in
the system. Extra-length audio and video cables can
cause signal loss and act as an “antenna” for noise.

• When routing RCA cables, keep them away from power
cables and output speaker wires.

Operation Precautions

• Do not allow liquids or foreign objects to enter the
MSS430 Multistation A/V Selector or Control Station(s).

• If any unit should become wet, turn off all power and let
your authorized Clarion dealer clean or service the equip­ment.

DO NOT ATTEMPT TO OPEN OR SERVICE THE
MSS430 OR CONTROL STATIONS. THE INTER­NAL PARTS ARE NOT USER-SERVICEABLE.
DOING SO WILL VOID THE WARRANTY.

• Do not place heavy objects on the MSS430 Multistation
A/V Selector or Control Station(s).

SOURCE COMMANDER MSS430

4

• Do not drop or excessively jar the MSS430 Multistation
A/V Selector or Control Station(s).

• Do not use liquid cleaners on any surfaces. Only use a
soft (cotton or other non-static) cloth to wipe off finger­prints or other imprints from the faceplate or remote con­trol.

• Do not subject the unit to direct sunlight or an extremely
hot environment (e.g., closed windows on a hot summer
day , direct path of heater vent, etc.).

• Avoid using the products under the following conditions:
– After extended parking on an extremely hot or cold day
– Near strong magnetic fields
– In an environment with excessive humidity , dust, or

vibration (e.g., off-road travel, etc.)

OWNER’S MANUAL/INSTALLATION GUIDE

5

INSTALLATION AND WIRING

Parts List

• (1) Source Commander MSS430 A/V Selector

• (3) Control Stations

• (3) Control Station Cables

• (2) Mounting L-Brackets

• (4) M4 x 8 Pan Head Machine Screws

• (4) M4 x 15 Self-tapping Sheet Metal Screws

• (1) 4-pin Molex Power Connector

• (3) 2-pin Monitor Power Connectors

• Owner’s Manual/Installation Guide

• Warranty Registration Card

Installing the MSS430

Figure 1. Installing the MSS430.

RL

V

RL

V

R

L

V

RL

V

POWER

M4 x 15 Self-tapping
Sheet Metal Screw
(4 supplied)

M4 x 8 Pan Head
Machine Screws
(4 supplied)

SOURCE COMMANDER MSS430

6

Installing the Control Station

Figure 2. Installing the Control Station in a center console.

MSS430 Wiring for the 4-Pin Power Harness

Figure 3. Wiring and pinouts for the 4-pin power harness.

Reverse (Green)

None

Ignition (Red)

Ground (Black)

1
2
3
4

1 2

34

END

VIEW

To Ground

Black

Green

Reverse Switch

To Vehicle

Circuits

Ignition Switch

Reverse Lights
(on vehicle’s rear)

Battery

+

-

Red

Fuse

Opening

Mounting Bazel

Control Station