C
ongratulations on your purchase of the Ungo Security System.
This Ungo Security System was designed in the heart of
California’s high-tech “Silicon Valley” by Ungo Security
Corporation, a subsidiary of Clarion Corporation. Since its founding in
1975, Ungo has been recognized as a pioneer and long time industry
leader in vehicle security.
Please read this manual thoroughly to familiarize yourself with your
system’s components and operation. Discuss any questions you might
have with your installing dealer.
Record the serial number of your Ungo system and keep all dealer
records and receipts. Be sure to discuss the installation with the dealer
so that you understand the specifics of the installation in your vehicle.
Also, do not forget to complete and mail the Product Warranty
Registration Card within 60 days of purchase and insure that the
installing dealer has stamped and signed the appropriate section in
order to properly register your warranty.
Table of Contents
1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
2. Remote Transmitters
Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Ungo Standard Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Convenience Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Driver Door Priority Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Adding a New Transmitter into the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Deleting Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
3. Basic Operation
Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Silent Arming / Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Arming Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Automatic System Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Full Time System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
4. Other Features
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Ignition Controlled Door Locking / Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Auxiliary Function Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Remote Car Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Garage Door Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
5. Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
6. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
7. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
Note: Certain features described in this manual may require additional parts and/or labor. Also, many features of
the Ungo MS850 security systems have selectable options that must be activated or programmed during the
system’s installation. These items will be identified in the following sections. Your Authorized Ungo Dealer
will be happy to discuss these features with you and help you design your system to meet your needs.
Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features
designed to:
❐
Deter
potential intrusions to the vehicle by continually flashing the system LED status
indicator while the system is Armed, giving a visual indication to any passer-by that the
system is equipped with a security system.
❐
Detect
intrusions to the vehicle, including impacts to the vehicle’s body and glass, and
opening of the doors, trunk and hood.
❐
Alert
those in the vicinity of the vehicle by sounding the system’s siren and flashing,
parking lights, and honking the horn.
❐
Inform
the owner when the system has been triggered and specifically which zone was
violated. The system will also inform the user of any bad switches or sensors that may
be causing the system to function improperly.
❐
Protect
both you and the contents of your vehicle with features such as panic mode,
dome light illumination, and ignition controlled door locking.
Each Ungo MS850 System comes with:
• Main Unit - the “brain” of the system.
• 2 - Two Button Remote Transmitters
• 125dB Siren* - Water resistant, high output siren that sounds when system is triggered.
Also used to provide audible system status information.
*As an option, your system can be configured to use your vehicle’s horn instead of a siren for a more distinct
and identifiable sound.
• Status LED - red illuminated indicator that provides system status information.
• 2 Stage Electronic Shock Sensor - detects impacts to the vehicle.
• Emergency Override / Valet Switch - used to override the system in case the Remote
Transmitters become lost or stolen. Also used to temporarily disable the system when the
vehicle is being serviced or turned over to a parking attendant.
Options and Convenience Features
The advanced design of the Ungo system incorporates a number of optional inputs and outputs
allowing you to create a customized security / convenience system by easily accommodating
many optional convenience and security features such as:
About Your Ungo Security System
MS850 Owner’s Manual - Page 1
❐ Remote Door Locking
❐ Starter Disable
❐ Remote Window Control
❐ Remote Car Start
❐ Extended Range Antenna
❐ Power Trunk / Hatch Release
❐ Glass Breakage Sensor
❐ Radar Sensor
❐ Garage Door Receiver
❐ Back-up Battery Siren
Remote Transmitter Layout
The Ungo MS850 comes with 2 multi-function Remote Transmitters used to control nearly all of
the system’s features.
Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is
taking place.
These Remote Transmitters may be used in one of three operating modes:
Ungo Standard
Mode, Convenience Mode,
and
Driver Door Priority Mode
.
Ungo Standard Mode (default)
The MS850 system is pre-programmed to operate in the Ungo Standard Mode.
Button 1 Arms and Disarms the system. This Button also locks and unlocks the doors when the
system is in Valet Mode.
Button 2 controls the system’s Auxiliary Function 1, which is normally used for activating a car’s
electric trunk release.
The following diagram illustrates how the Remote Transmitter controls the functions of the
system when used in the Ungo Standard Mode:
Remote Transmitters
Button 1
Button 2
LED
Page 2 - MS850 Owner’s Manual
BUTTON 1
BUTTON 2
ARM / DISARM
F1
Convenience Mode
This configuration allows the MS850 to operate with separate Arm and Disarm buttons for greater
convenience and ease of use.
Button 1 Arms the system. This Button also locks the doors when the system is in Valet Mode.
Button 2 Disarms the system. Pressing Button 2 again activates the system’s Auxiliary Function 1.
This Button also unlocks the doors when the system is in Valet Mode.
If the system is Armed, pressing Button 2 will Disarm the system.
If the system is Disarmed, pressing Button 2 will activate the Auxiliary Function.
If the system is in Valet and the doors are locked, pressing Button 2 will unlock the doors.
The following diagram illustrates how the Remote Transmitter controls the functions of the
system when used in the Convenience Mode:
Driver Door Priority Mode*
This configuration adds the security of unlocking only the driver’s door when the system is
Disarmed. Pressing the Disarm button again will unlock all remaining doors.
Button 1 Arms the system. This Button also locks the doors when the system is in Valet Mode.
Button 2 Disarms the system and at the same time activates Auxiliary Function 1 (which unlocks
the driver’s door). This Button also unlocks the doors when the system is in Valet Mode.
If the system is Armed, pressing Button 2 will Disarm the system and unlock the driver’s door only.
If the system is Disarmed, pressing Button 2 will unlock all remaining doors.
If the system is in Valet and the doors are locked, pressing Button 2 will unlock the driver’s door. Pressing Button
2 again will unlock all remaining doors.
The following diagram illustrates how the Remote Transmitter controls the functions of the
system when used in the Driver Door Priority Mode:
*Extra parts and/or labor may be required to properly utilize this mode. See your Authorized Ungo Dealer for details.
Unlock All
ARM
DISARM*
BUTTON 1
BUTTON 2
*Disarming the system will unlock only the Driver's Door
F1
ARM
DISARM
BUTTON 1
BUTTON 2
MS850 Owner’s Manual - Page 3
Two Car Operation
If you want to control two Ungo Security systems by a single Remote Transmitter, the unused
functions of the Remote Transmitter can be set up by your dealer to operate another Ungo
Security system, giving you the convenience of operating multiple vehicles from a single Remote
Transmitter.
When set up for two car operation, the Remote Transmitters will function as in the example
below:
For more information about Two Car operation, see your Authorized Ungo Dealer.
ARM / DISARM (A)
ARM / DISARM (B)
BUTTON 1
BUTTON 2
Page 4 - MS850 Owner’s Manual
Adding a New Transmitter into the System
The Ungo MS850 has the ability to recognize up to 21 individual remote transmitters. If the
vehicle is used by multiple drivers, each can have their own Remote Transmitter.
To add a Remote Transmitter:
1. Turn on the ignition.
2. Press and hold the Override switch.
• The status LED will turn on red.
3. Within 5 seconds:
Continue holding the Override switch
and Press Transmitter Button 1* for remote
arming
with
chirp confirmation.
--- or ---
Release the Override switch
and Press Transmitter Button 1* for remote arming
without
chirp confirmation.
• The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program
either
of the
Transmitter’s function buttons to arm and disarm the system at this point.
Deleting Transmitters (Adding a Remote Transmitter
and
Erasing All
Other Remote Transmitters From the System)
1. Turn on the ignition.
2. Press and hold the Override switch.
• The status LED will turn on red.
Continue to hold the Override switch.
• After 5 seconds, the status LED will flash 4 times, then turn on red again.
3. Within 5 seconds:
Continue holding the Override switch
and Press Transmitter Button 1* for remote
arming
with
chirp confirmation.
--- or ---
Release the Override switch
and Press Transmitter Button 1* for remote arming
without
chirp confirmation.
• The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program
either
of the
Transmitter’s function buttons to arm and disarm the system at this point.
MS850 Owner’s Manual - Page 5
Page 6 - MS850 Owner’s Manual
Battery Replacement
Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced
from time to time. Under normal conditions, the battery should last for up to a year before it
needs replacement.
When your Remote Transmitter’s battery is in need of replacement, you will notice a decrease in
your system’s operating range or a decrease in the brightness of the Transmitter’s LED indicator .
To change the battery, remove the 2 screws at the back of the Transmitter and carefully separate
the top and bottom halves of the Transmitter case.
Insert the new battery, making sure that the positive and negative terminals are positioned
correctly and replace the cover.
Battery Type: 23A
MS850 Owner’s Manual - Page 7
Remote Arming
When Armed, the system monitors and protects 4 independent areas, or
zones
, including the
ignition switch, doors, shock sensor, and hood/trunk.
To Arm the System:
1. Turn off the ignition.
2. Press Button 1.
• The siren will chirp once.*
• The doors will lock.
• The parking lights will flash once.
• The LED will turn on red, indicating the ignition, doors, hood and trunk inputs are
activated.
* The siren chirp(s) during Arming will alert you the condition of the system and vehicle when the system is
armed.
1 chirp = normal arming
1 + 4 chirps = door, hood, or trunk open
During Arming, if the system detects a bad sensor or an open zone, the system will ignore that input, but keep all
other areas protected.
3. After 10 seconds:
• The LED will begin blinking, indicating that the sensor inputs are activated.
While the system is Armed, the system will trigger if:
• The ignition key is turned on.
• The doors are opened.
• The Shock Sensor detects an impact to the vehicle.
• The hood or trunk is opened.
• A connected optional sensor is disturbed.
When triggered, the siren will sound, and the parking lights will flash. If the system is
triggered by the ignition, doors, hood, or trunk, the system will alarm for 40 seconds. If
triggered by the shock sensor, the system will alarm for 20 seconds.
If the same input triggers the system 3 times during a single arming cycle, the system will
bypass that input, keeping the other zones protected, until the next time the system is
armed.
If the Shock Sensor detects a light impact to the car or a connected optional sensor triggers
the system’s Warn Away input, the siren will sound a chirp to warn away the potential
intruder.
Basic Features
Page 8 - MS850 Owner’s Manual
Remote Disarming
To Disarm the System:
Press Button 1.
• The siren will chirp twice.*
• The doors will unlock.
• The parking lights will flash twice.
• The LED will turn off.
* The siren chirps during disarming will alert you if the system had been triggered while armed.
2 chirps = normal disarming
1 long chirp = Tamper Alert - system was triggered
Tamper Alert
On Disarming, if the system responds with one long chirp, indicating the system was triggered,
the LED will flash for 60 seconds to indicate the zone that triggered the system. If the Audible
Tamper Alert Report feature is turned on during installation, the siren will chirp to indicate the
triggered zone.
LED Flashes (60 seconds):
1 flash = door
2 flashes = Shock Sensor
3 flashes = trunk
example: flash-flash-pause-flash-flash-pause = Shock Sensor
Siren Chirps (once only)
1 chirp = door
2 chirps = Shock Sensor
3 chirps = trunk
Silent Arming / Disarming
Each Remote Transmitters can be individually set to Arm and Disarm the system with or without
chirp confirmation at the time they are programmed into the system (see Adding a New
Transmitter into the System).
To temporarily cancel the Arming and Disarming confirmation chirps, you can Arm or Disarm the
system by pressing Buttons 1 and 2
together
.
Note: The confirmation chirps will only be cancelled if the system status is normal. The chirp indications for Tamper
Alert and the open zone warning will not be cancelled when the system is Armed or Disarmed silently .
Arming Mode Selection
Your system can be set in one of the following Arming Modes:
• Passive (automatic) Arming
with
chirp confirmation
• Active Arming (by Remote Only)
• Passive (automatic) Arming
without
chirp confirmation
To set the Arming Mode:
1. Turn the ignition on.
2. Within 4 seconds, press Buttons 1 and 2 together.
First push: one chirp = Passive Arming with chirp
Second push: two chirps = Active Arming
Third push: three chirps = Passive without chirp
3. Turn the ignition off to save your selection.
Passive Arming
When the Arming Mode has been set for
Passive Arming
, the system arms itself automatically,
each time the ignition is turned off and all of the doors, hood and trunk are closed.
To start the Passive Arming Process:
1. Turn off the ignition.*
• The status LED will begin to flash quickly.
2. Open the door and exit the vehicle.
• Once all doors are closed and the dome light is turned off, the LED will turn off.
3. After 10 seconds,
• The siren will chirp.
• The parking lights will flash.
• The doors will lock.**
• The status LED will flash red, indicating the system is armed.
4. The system is now armed.
* The ignition must have been on for
at least
4 seconds before the Passive Arming sequence will begin.
** If the Passive Locking feature is selected.
To temporarily disable Passive Arming, you can turn the ignition key on then off, within 4
seconds. The status LED will stop flashing, and the system will not passively arm until the next
time the key is on for more than 4 seconds. This feature is useful for turning off passive arming
when refueling or washing your car or if you want to sit in your car and do not want the system
to arm.
Panic Mode
Allows you to instantly trigger the alarm in an emergency situation by the Remote Transmitter.
To enter Panic Mode:
1. Press and hold Button 1 for 2 seconds.
• The system will trigger.
2. Press Button 1 again to stop Panic Mode.*
If Panic Mode is not stopped by the Remote, it will automatically time out after 40 seconds, and
the system will return to its prior Armed/Disarmed state.
* In Convenience Mode and Driver Door Priority Mode, Press Button 2 to stop Panic Mode.
MS850 Owner’s Manual - Page 9
Emergency Override
In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter
and drive your car by using the following procedure. Be sure that you have your ignition keys
ready and that you know the location of the override switch before you perform this procedure.
To override the system:
1. Unlock the door using the key.
2. Enter the vehicle.
• Because the system is armed, the system will trigger and the siren will be sounding.
3. Turn ignition key on.
4. Within, 4 seconds, press and hold the override switch.
• The system will disarm.
5. You can now start and drive the car.
Note: During installation, your installer can program the system to give 10 second entry delay when the system Arms
passively. When the door is opened while the system is Armed, the siren will give a series warning of chirps
for 10 seconds before sounding, giving you time to perform the emergency override procedure.
Automatic System Rearming
This feature, which can be turned on by your installer during the installation, insures the security
of the system by protecting your car in case of an accidental disarm.
If your system becomes disarmed due to an accidental press of the Arm/Disarm Button, the
system will automatically rearm if no other activity is detected within one minute.
One minute after Remote Disarming, the system will alert you with a 10 second series of chirps,
then arm. (If the Passive Door Locking feature is selected during the installation, the system will
also relock the doors.)
Any of the following will cancel Automatic System Rearming:
• Turn on the ignition.
• Open the Trunk or Hood.
• Activate Auxiliary Function.
Automatic System Rearming is independent of Passive Arming and only takes place if the system
was Armed (actively or passively) for at least 10 seconds and then Disarmed by the Remote
Transmitter.
Full Time System Diagnostics
The system continuously monitors all protected zones, even when it is not armed, and warns you
if it detects a problem when you turn off the ignition.
1. Turn off the ignition.
2. If the siren chirps twice, the system has detected a problem.*
3. The status LED will flash to indicate the zone where the problem has been detected.
1 flash = door
2 flashes = Shock Sensor
3 flashes = hood / trunk
* The system must see the zone open or active for at least 20 seconds before the zone is determined to be defective.
This way, opening the car door before turning off the ignition will not cause the siren to emit the warning chirps.
Page 10 - MS850 Owner’s Manual
MS850 Owner’s Manual - Page 11
Valet Mode
Allows you to temporarily disable the security system when the car is being service or turned over
to a parking attendant.
To turn Valet Mode on or off:
1. Turn on the ignition.
2. Press and hold the override switch.
3. While holding the override switch, turn off the ignition.
• The siren will chirp
once
to indicate you have turned Valet Mode on.
• The siren will chirp
twice
to indicate you have turned Valet Mode off.
4. Release the override switch.
While Valet Mode is on, you can continue to lock and unlock your doors with the Remote
Transmitters, as well as operate the Auxiliary Functions.
For added protection, when the doors are locked by the Remote Transmitter , the system’s Starter
Disable circuit will activate and the LED will emit double flashes until the system is unlocked by
the Remote.
If the Remote Transmitter is lost or becomes inoperable while the car is locked in Valet Mode,
you can use the
Emergency Override
procedure to deactivate the Starter Disable circuit.
Ignition Controlled Door Locking
For added convenience and safety, this feature automatically locks your car’s doors 10 seconds
after the ignition key is turned on.
To prevent you from accidentally locking your keys inside the car:
• The system will not automatically lock the doors if a door is open when the ignition key is turned on.
• The system will not automatically lock the doors if a door is opened during the first 10 seconds after the
ignition key is turned on.
Ignition Controlled Door Unlocking*
For added convenience, this feature automatically unlocks your car’s doors after the ignition key
is turned off.
*For personal safety reasons, this feature can be turned off by your installer.
Dome Light Control
As an option, the systems Auxiliary Function can be used to control your vehicle’s dome light.
For increased safety and convenience this feature will automatically turn on the dome light when
you Disarm the system.
With this feature installed, the dome light will turn on for 20 seconds when the system is disarmed
(or unlocked in Valet Mode) using the Remote Transmitter.
Other Features
Page 12 - MS850 Owner’s Manual
Auxiliary Function Output
The system is equipped with an Auxiliary Function output that can be used to remotely control
an optional feature such as, electric trunk release, remote car starter, power windows, power
sunroof, garage door receiver, etc.
To operate the Auxiliary Function, press Button 2.
• This function will operate regardless of whether the system is armed or disarmed and
will stay active for as long as the Button 2 is held.
Trunk Bypass*
If the Auxiliary Function is being used to remotely open your car’s trunk, your installer can
program the system to allow you to access the trunk remotely while the system is armed, without
triggering the alarm. This will allow you to load or retrieve packages from the trunk without having
to first disarm the alarm.
When the trunk is opened using the remote transmitter, the trunk input, and shock sensor will be
ignored until the trunk is closed.
*To utilize this feature, the alarm’s trunk input must be connected to a trunk pinswitch. If your car is not equipped with a
trunk pinswitch, one can be installed by your Ungo dealer for an additional charge.
Remote Car Starter
When an optional Remote Car Starter (Ungo model number SAA4295) is installed into your car,
the Remote Transmitter can be used to remotely start and run your vehicle to warm-up the
engine, as well as activate the heating / air conditioning system.
Garage Door Receiver
When an optional Garage Door Receiver (Ungo model number SAA5999) is used with your
system, the Remote Transmitters can be set to control almost any automatic garage door opener .
By adding this feature to your system, you not only add the convenience of being able to open
your garage door and activate your car security system by the same remote, but you also add
the protection of Ungo’s V aricode 2 anti-code grabbing technology to your automatic garage door
opener.
As an added benefit, by not keeping a garage door opener in your car, your garage is protected
from break-in by a thief who might break into your car to steal your garage door opener.
Additional Remote Transmitters
Additional Remote Transmitters for your MS850 are available from your Authorized Ungo dealer.
MS850 Owner’s Manual - Page 13
You can use this chart to quickly identify and interpret your system’s chirp indications and LED
flashes.
Reference Chart
1 chirp arming normal arming
1 + 4 chirps arming door, hood, or trunk is open
Output When Status
2 quick chirps arming Valet Mode is on
LED double flashes Valet Mode Starter Defeat Activated
2 chirps disarming normal disarming
1 long disarming Tamper Alert - system was triggered
no chirps after Tamper Alert ignition
1 chirp after Tamper Alert door
2 chirps after Tamper Alert shock sensor
3 chirps after Tamper Alert hood or trunk
no LED flashes after Tamper Alert ignition
1 LED flash after Tamper Alert door
2 LED flashes after Tamper Alert shock sensor
3 LED flashes after Tamper Alert hood or trunk
1 chirp while Armed Warn Away
4 chirps with ignition key on Sensor Test mode on
1 chirp in Sensor Test mode impact detected
Double chirps 1 minute after disarming Automatic Rearming
(for 10 seconds)
LED flashing quickly ignition key off Passive Arming sequence started
Two chirps ignition key off Full Time System Diagnostics
1 LED flash after Full Time Sys. Diag. door
2 LED flashes after Full Time Sys. Diag. shock sensor
3 LED flashes after Full Time Sys. Diag. hood or trunk
Double chirps while Armed System Triggered
(Passive Arming Entry Delay Warning)
Page 14 - MS850 Owner’s Manual
Technical Data
Specifications
Main Unit
Voltage: 12v, negative ground
Current Consumption: <5mA
Temperature Range: -40oF to +170oF
-40oC to +77oC
Auxiliary Output Capability: 500mA
Internal Relays: 12/28A
Transmitter
Current Consumption: <.002mA, standby
Battery Type: miniature 12v, type 23A
FCC ID:
MP62VUUUNGO850
HP92VUUNGO603/03
T
HIS DEVICE COMPLIES WITH FCC RULES PART 15.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE THAT MAY BE RECEIVED
, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION
.
Ungo Security Corporation
Gardena, CA
USA
Warranty Information
Model No.: MS850
Serial No.:
Dealer Name:
Address:
Purchase Date:
MS850 Owner’s Manual - Page 15
1. Ungo Security Corporation of Gardena, California ("Ungo
Security") warrants this Ungo system to be free from defects
in materials and workmanship and to comply with Ungo
Security’s applicable printed specifications.
2. Ungo Security systems carry a limited lifetime warranty
on the Main unit (system brain) and transmitters. The
warranty is limited to Ungo Security systems that have been
installed by an approved Ungo dealer and is extended to the
Original Purchaser ("Owner") and to the original vehicle in
which it was installed only, and is not transferable to any
subsequent owner or owners of the product(s).
All other products (including those products of other
manufacturers which are supplied by Ungo security as a
part of, or an accessory to, an Ungo Security-manufactured
product) are warranted by Ungo security for a period of one
year from the date of sale to the Owner. For specific
identification of such products contact Ungo Security.
3. This warranty shall not cover: (I) any damage caused by
Owner’s negligence or misuse of any kind, or any damage
due to causes unrelated to Ungo Security’s manufacturing,
including, but not limited to improper servicing or repair by
someone other than Ungo security or an authorized service
facility: (II) alterations or modifications to the Ungo System
other than the addition of an authorized accessory: or (III)
improper installation or removal from the vehicle contrary to
Ungo Security’s instructions.
4. Obligations of Ungo Security. In the event the Owner’s
Ungo System does not comply with this warranty, it must be
returned to Ungo security as specified below. Ungo security
will repair or replace it with a new or reworked unit, within
thirty (30) days of receipt and acceptance of such defective
unit, and without cost to Owner.
5. To make a claim under the warranty. Owner must: (I)
provide Ungo security with written notice that the Ungo
System does not comply with the warranty within thirty (30)
days from the date of the Owner’s discovery of the defect
and (II) furnish proof of purchase and purchase date (this
requirement is satisfied if Ungo security has a completed
warranty registration card on file).
6. Owner obligations. To obtain Warranty Service, Owner
must at Owner’s expense: (I) have the Ungo System
removed from the vehicle by an authorized Ungo Security
dealer, (II) package the unit in a reasonable manner to
prevent damage to the unit during shipment; and (III) ship
the unit, freight prepaid, to Ungo Security’s factory or other
authorized repair facility.
7. Repair facility locations. To obtain the name, address
and phone number of the nearest Authorized Ungo Repair
Facility, Owners may contact Ungo security at 310-327-
9100.
8. The Owners of Ungo Systems in California have the right
to have the product serviced or repaired during the warranty
period. The warranty period will be extended for the number
of full days that the product has been out of the Owner’s
hands for warranty repairs. If a defect exists within the
warranty period, the warranty will not expire until the defect
has been fixed. The warranty period will also be extended if
the repair has not been performed due to delays caused by
circumstances beyond the control of the Owner, or if the
warranty repairs did not remedy the defect and the Owner
notifies Ungo Security or the seller of the failure of the repairs
within sixty (60) days after they were completed. If, after a
reasonable number of attempts, the defect has not been
fixed the Owner may return this product for replacement or a
refund, subject in either case, to a deduction of a reasonable
charge for usage. The time extension does not effect the
protection or remedies the Owner has under other laws.
9. Exclusions from liability.
(A) In no event shall Ungo security be liable for any loss or
damages beyond the original purchase price of the Ungo
system, and Ungo security specifically excludes any and all
incidental and consequential damages, whether resulting
from breach of warranty or contract, negligence or other
conduct in connection with any sale, use, servicing or repair
of a unit. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you.)
(B) There are no warranties, express, statutory or implied,
which extend beyond that which is described herein, and in
particular, all implied warranties of merchantability and
fitness for a particular purpose, and all warranties of title and
against encumbrances, are expressly disclaimed, limited
and excluded as permitted by law; but in no event shall any
implied warranty, whether of merchantability of fitness for a
particular purpose or otherwise, have a duration exceeding
that of the express warranty made herein. (Some states do
not allow limitation on how long an implied warranty lasts, so
the above limitation may not apply to you.)
(C) No agent, officer, employee or representative of Ungo
Security, or any other person, has authority to make any
representations, promises or warranties respecting Ungo
Systems and their authorized accessories.
(D) Owner has the right to bring any action at law or in equity
to resolve disputes concerning, or to enforce, the provisions
of this warranty. No action at law or in equity may be brought
against Ungo security for breach of warranty or contract or
based on negligence of other conduct more than three (3)
years from the date the cause of action has occurred.
(E) This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
(F) The remedies extended herein are the sole and
exclusive remedies available to Owners of Ungo systems.
(G) Under no circumstances should this warranty, or the
products covered by it, be construed as an insurance policy
against loss.
Warranty Information
Ungo Security Corporation
A Clarion Company
661 West Redondo Beach Blvd.
Gardena, CA 90247
800-Go-Clarion
www.clarionmultimedia.com
© Ungo Security Corporation, Gardena, CA 97-MS850-10 Rev. 1 (1/99)
Loading...