Please read this owner’s manual in its entirety before operating this equipment.
∗
After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
∗
Check the contents of the enclosed warranty card and keep it carefully with this manual.
∗
This manual includes the operating procedures of the iPod® interface, CD/DVD changer
and TV tuner connected via the CeNET cable. The iPod interface, CD/DVD changer and
TV tuner have their own manuals, but no explanations for operating them are described.
“iPod” is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
이사용설명서를 읽어보신 후에는, 언제든 볼 수 있도록 가까운 곳(예: 글로브 박스)에 보관해
∗
주십시오 .
동봉된 품질 보증서의 내용을 확인하신 후 , 이 사용 설명서와 함께 소중하게 잘 보관해 주십시
∗
오.
∗
이사용설명서에는 CeNET 케이블로 연결된 iPod
너에 관한 조작 절차가 포함되어 있습니다. iPod 인터페이스, CD/DVD 체인저와 TV 튜너는
자체 사용 설명서가 있지만 , 그들의 조작에 관한 설명은 되어 있지 않습니다 .
"iPod" 은 Apple Computer, Inc. 의 상표이며 , 미국과 기타 국가에서 등록되어 있습니다 .
®
인터페이스 , CD/DVD 체인저와 TV 튜
Be sure to unfold and read the next page.
반드시 다음 페이지를 펴서 읽으십시오.
请务必展开并阅读下一页。
DXZ776USB
i
English
CONTROLS /
[
OPTION
]
]
主机
]
Source unit / /
中文
[
SRC
[
RELEASE
본체
控制键
[
SEEK PANEL
컨트롤
/
]
[
MENU
]
[
ENT
]
English
中文한국어
Bottom View of Source Unit
主机的仰视图
본체의 저면도
한국어
[
]
VOL
[
] (EJECT)
[ ] (MUTE)
[
]
TITLE
With the MOTORIZED FACE opened
[
IR RECEIVER
在自动面板打开的情况下
/ /
[CD SLOT]
전동 프런트가 열린 상태
[
ISR
[
]
]
[
P.CH
] (SOUND)
]
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
注:在阅读各章时请务必展开此页并参考主视图。
주: 이 페이지를 펼쳐두고, 각 장을 읽을 때 전면 그림을 참조하도록 하십시오.
ii
DXZ776USB
iii
DXZ776USB
Contents
CONTROLS............................................................................................................................................ ii
• “Digital Time Alignment” & “Digital 3way X-Over” for sound creation
• “SLIDETRAK” for dynamic operation
• Full dot display with 728-variable colour illuminated key & Motorised Sloping Console
1 DXZ776USB
English
2. PRECAUTIONS
1. When the inside of the car is very cold and
the player is used soon after switching on the
heater moisture may form on the disc or the
optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft cloth.
If moisture forms on the optical parts of the
player, do not use the player for about one
hour. The condensation will disappear
naturally allowing normal operation.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN, MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT
BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE
MANUFACTURER FOR COMPLIANCE
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY.
Motorized Face
This unit uses motorized face to make large-screen displays possible.
When you use the motorized face, be sure to close it.
CAUTION
BE CAREFUL NOT TO GET YOUR FINGERS
CAUGHT WHEN OPENING AND CLOSING
THE MOTORIZED FACE.
1. For safety’s sake, always close the
MOTORIZED FACE before leaving this unit
unused for a prolonged period or switching
OFF the ignition key.
If you switch OFF the ignition key with the
MOTORIZED FACE tilted, the MOTORIZED
FACE does not close.
2. Before the MOTORIZED FACE closes, there
may be a braking sound from the safety
mechanism. This is normal.
3. If you move the MOTORIZED FACE by
hand, this may create play. To correct this
play, with the power on for the unit, press the
[Q] button to close the MOTORIZED FACE.
4. After a disc is ejected, the MOTORIZED
FACE automatically returns to the tilted or
closed state. If there is any obstruction when
the MOTORIZED FACE tries to close, the
safety mechanism is triggered and the
MOTORIZED FACE returns to the open
state. If this happens, remove the
obstruction, then press the [Q] button.
5. To avoid scratching the compact disk, keep
the CD level when inserting or removing
them.
CAUTION
2
DXZ776USB
Handling Compact Discs
Use only compact discs bearing the or
mark.
Do not play heart-shaped, octagonal, or other
specially shaped compact discs.
Some CDs recorded in CD-R/CD-RW mode
may not be usable.
Handling
• Compared to ordinary music CDs, CD-R and
CD-RW discs are both easily affected by high
temperature and humidity and some of CD-R
and CD-RW discs may not be played.
Therefore, do not leave them for a long time
in the car.
• New discs may
have some
roughness
around the
edges. If such
discs are used,
the player may
not work or the
sound may skip. Use a ball-point pen or the
like to remove any roughness from the edge
of the disc.
• Never stick labels on the surface of the
compact disc or mark the surface with a
pencil or pen.
• Never play a compact disc with any
cellophane tape or other glue on it or with
peeling off marks. If you try to play such a
compact disc, you may not be able to get it
back out of the CD player or it may damage
the CD player.
• Do not use compact discs that have large
scratches, are misshapen, cracked, etc. Use
of such discs may cause misoperation or
damage.
• To remove a compact disc from its storage
case, press down on the center of the case
and lift the disc out, holding it carefully by the
edges.
• Do not use commercially available CD
protection sheets or discs equipped with
stabilizers, etc. These may damage the disc
or cause breakdown of the internal
mechanism.
Ball-point pen
Roughness
English
Storage
• Do not expose compact discs to direct
sunlight or any heat source.
• Do not expose compact discs to excess
humidity or dust.
• Do not expose compact discs to direct heat
from heaters.
Cleaning
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the
center of the compact disc to the
circumference.
• Do not use any solvents, such as
commercially available cleaners, anti-static
spray, or thinner to clean compact discs.
• After using special compact disc cleaner, let
the compact disc dry off well before playing it.
DXZ776USB
3
English
3. NOMENCLATURE
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “
Names of the Buttons and Their Functions
CONTROLS
” on page ii (unfold).
[RELEASE] button
• Deeply push in the button to unlock the DCP.
[SRC] button
• Press the button to turn on the power.
• Press and hold the button for 1 second or
longer to turn off the power.
• Switch the operation mode among the radio
mode, etc.
[OPTION] button
• Press the button to enter the option mode.
• Press and hold the button for 1 second or
longer to enter the adjust mode.
[SEEK PANEL]
• The [
SEEK PANEL
the ends to be moved to right or left to permit
station tuning (radio), track selection (CD),
and to perform various settings in the
adjustment mode.
] allows the controls on
[MENU] button
• Switch the band, or seek tuning or manual
tuning while in the radio mode.
• Press the button to enter the list search mode
while in the CD/MP3/WMA/AAC mode.
• Press and hold the button for 1 second or
longer to play the first track while in the CD/
MP3/WMA/AAC mode.
• Press the button to change the character.
[] button
• Play or pause a track while in the CD/MP3/
WMA/AAC mode.
• Press the button to enter the preset memory
mode (radio).
• Confirm various settings.
[P.CH] button
• Push the button upward or downward to recall
the stored station while in the radio mode.
• Select the folder while in the MP3/WMA/AAC
mode.
• Perform various settings.
[] (SOUND) button
• Press the button to enter the sound mode.
• Press and hold the button for 1 second or
longer to enter the sound setting mode.
[ISR] button
• Recall ISR radio station in memory.
• Press and hold the button for 2 seconds or
longer: Store current station into ISR memory
(radio mode only).
[IR RECEIVER]
• Receiver for remote control unit. (Operating
range: 30° in all directions)
[TITLE] button
• Use the button to switch the user titles or
track titles, etc. while in the CD/MP3/WMA/
AAC mode.
• Press and hold the button to switch the
display indication (Action display, Title display
and Clock time display).
[] (MUTE) button
• Turn mute on or off.
[Q] (EJECT) button
• Press to open the MOTORIZED FACE and
insert a CD into the CD SLOT.
• Press to eject a CD loaded in the unit.
[VOL] button
• Push the button upward or downward to
adjust the volume.
[CD SLOT]
• CD insertion slot.
4
DXZ776USB
Display Items
Source indication
•
FM1-3, AM : Radio mode
•
CD : CD/MP3/WMA/AAC mode
•
USB : USB mode
•
iPod : iPod BB mode
•
CDC1-4 : CD changer mode
•
DVDC1-4 : DVD changer mode
•
TV1-2 : TV mode
•
AUX : AUX mode
•
TEL : Telephone mode
Source icon
(3 patterns)
•
Radio mode: Preset No. / frequency
•
CD mode : Track No. / playback time
•
MP3/WMA/AAC mode
: Folder No. /track No. / playback time
•
CD / DVD changer mode
: Disc No. / track No. / playback time
•
TV mode : Preset No. / channel
Clock time
indication
Operation status indication
Titles indication
English
A.RDM : Disc/Folder random
A.RPT : Disc/Folder repeat
A.SCN : Disc/Folder scan
RDM : Track random
RPT : Track repeat
SCN : Track/Preset/Service scan
AS : Auto store
DZE : Digital Z-Enhancer indication
SR : Sound restorer indication
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
DXZ776USB
5
English
4. DCP
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP (DETACHABLE CONTROL PANEL)
case to prevent scratches.
We recommend taking the DCP with you when
leaving the car.
Removing the DCP
1. With the MOTORIZED FACE closed, turn off
the power.
2. Press the [
the DCP.
3. Pull the DCP toward you and remove it.
RELEASE
[RELEASE] button
DCP
] button deeply to open
CAUTION
• Always close the MOTORIZED FACE
before removing the DCP.
• If you remove the DCP with the
MOTORIZED FACE open, the MOTORIZED
FACE closes immediately. Be careful not
to get your fingers caught.
Attaching the DCP
1. Insert the DCP so that the A section on the
right side of the DCP catches on the hook B
on the unit.
2. Press the left side C of the DCP carefully to
fit it in place.
CAUTION
• The DCP can easily be damaged by
shocks. After removing it, be careful not to
drop it or subject it to strong shocks.
• If the [RELEASE] button is pressed and
the DCP is not locked into place, it may fall
out from vibration of the car. This can
break the DCP, so after removing it, either
install it on the unit or put it in its DCP
case.
• The connector connecting the unit and the
DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, screwdrivers, etc.
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
6
DXZ776USB
5. REMOTE CONTROL
Inserting the Battery
1
Turn over the remote control unit and slide
the cover in the direction indicated by the
arrow in the illustration.
2
Insert the battery (CR2025) into the insertion
guides, with the printed side (+) facing
upwards.
3
Press the battery in the direction indicated by
the arrow so that it slides into the
compartment.
4
Replace the cover and slide in until it clicks
into place.
Notes:
Misuse may result in rupture of the battery,
producing leakage of fluid and resulting in personal
injury or damage to surrounding materials. Always
follow these safety precautions:
• Use only the designated battery.
• When replacing the battery, insert properly, with
+/– polarities oriented correctly.
• Do not subject battery to heat, or dispose of in fire
or water. Do not attempt to disassemble the
battery.
• Dispose of used batteries properly.
Insertion guide
R
2
C
0
2
5
English
DXZ776USB
7
Functions of Remote Control Unit Buttons
English
∗
Some buttons on the remote control unit have different functions from the corresponding buttons on the main
unit.
Signal transmitter
[
]
SRC
[
]
MUTE
[
]
ISR
[
]
SCN
●
Shared modes
[SRC] button
• Press the button to turn on the power.
Press and hold the button for 1 second or
longer to turn off the power.
• Use to alternate operation mode among the
various modes.
[w], [z] buttons
• Increases and decreases volume.
●
Radio mode
[BND] button
• Switches reception band.
[x], [v] buttons
• Moves preset channels up and down.
[SCN] button
• Press to perform preset scan.
• Press and hold the button for 2 seconds or
longer to perform auto store.
[
BND
[
DISP
[
RDM
[
RPT
]
]
]
]
[MUTE] button
●
• Turns mute function on and off.
[ISR] button
• Recalls ISR radio station stored in memory.
• Press and hold the button for 2 seconds or
longer to store current station in ISR memory
(radio mode only).
[DISP] button
• Press to alternate among action display, title
display and Clock time display, etc.
CD/MP3/WMA/AAC and USB
modes
[BND] button
• Press to play the first track.
[x], [v] buttons
• Press to move the tracks up and down.
• Press and hold the button for 1 second or
longer to perform fast-forward/fast-backward.
8
DXZ776USB
Functions of Remote Control Unit Buttons
[] button
• Switches between playback and pause.
[SCN] button
• Press to perform scan play.
• When in MP3/WMA/AAC and USB modes,
press and hold the button for 1 second or
longer to perform folder scan play.
[RPT] button
• Press to perform repeat play.
• When in MP3/WMA/AAC and USB modes,
press and hold the button for 1 second or
longer to perform folder repeat play.
[RDM] button
• Press to perform random play.
• When in MP3/WMA/AAC and USB modes,
press and hold the button for 1 second or
longer to perform folder random play.
●
CD changer/DVD changer modes
[BND] button
• Press to switch to next disc in ascending
order.
[x], [v] buttons
• Press to move the tracks up and down.
• Press and hold the button for 1 second or
longer to perform fast-forward/fast-backward.
[] button
• Switches between playback and pause.
[SCN] button
• Press to perform scan play.
• Press and hold the button for 1 second or
longer to perform disc scan play.
[RPT] button
• Press to perform repeat play.
• Press and hold the button for 1 second or
longer to perform disc repeat play.
[RDM] button
• Press to perform random play.
• Press and hold the button for 1 second or
longer to perform disc random play.
●
iPod BB mode
[x], [v] buttons
• Press to move the tracks up and down.
• Press and hold the button for 1 second or
longer to perform fast-forward/fast-backward.
[] button
• Switches between playback and pause.
[RPT] button
• Press to perform repeat play.
• Press and hold the button for 1 second or
longer to perform all repeat play.
[RDM] button
• Press to perform random play.
• Press and hold the button for 1 second or
longer to perform all random play.
●
TV mode
[BND] button
• Switches reception band.
[x], [v] buttons
• Moves preset channels up and down.
[SCN] button
• Press to perform preset scan.
• Press and hold the button for 2 seconds or
longer to perform auto store.
[RDM] button
• Press to alternate between TV and VTR.
English
DXZ776USB
9
English
6. OPERATIONS
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “
Basic Operations
CAUTION
Be sure to lower the volume before
switching off the unit power or the ignition
key. The unit remembers its last volume
setting. If you switch the power off with the
volume up, when you switch the power back
on, the sudden loud volume may hurt your
hearing and damage the unit.
Selecting speaker system
When this product is turned on for the first time,
it allows you to select a speaker system.
Speaker system
Speaker
system
NORMAL
(Normal)
3WAY
(3way)
2WAY
(2way)
●
Front speaker
(left)
Rear speaker
(left)
●
Tweeter (left)
Front speaker
(left)
Speaker configuration
Front 2ch Rear 2ch Subwoofer 2ch
High 2ch Mid 2chSubwoofer 2ch
High 2ch Mid 2chRear 2ch
Normal speaker system (NORMAL)
Front speaker
(right)
Rear speaker
Subwoofer
(right)
3way speaker system (3WAY)
Tweeter (right)
Front speaker
(right)
Subwoofer
●
Front speaker
(left)
1. Push the [
2. Press the [] button.
3. Push the [
4. Press the [] button to store the
∗
Note:
• The first time this unit is turned on after the wire
System check function
If you change your speaker system while the
power of this unit is on, perform the System
check function to select the appropriate speaker
system again. See “
check
Select the speaker system suited to your
speaker configuration. Failing to do so can
damage your speakers.
CONTROLS
” on page ii (unfold).
2way speaker system (2WAY)
Tweeter (left)
Rear speaker
(left)
SEEK PANEL
Tweeter (right)
Front speaker
(right)
Rear speaker
(right)
] leftward or
rightward to select the setting.
Each time you push the [
SEEK PANEL
]
leftward or rightward, the setting change in
the following order:
“
NORMAL” ↔ “3WAY” ↔ “2WAY” ↔
“
NORMAL
rightward to select “OK” or “
”...
SEEK PANEL
] leftward or
CANCEL
”.
setting.
Refer to the section “
(page 12) and “
(page 16).
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “
display, then the unit returns to the selecting
speaker system.
SYSTEM CHECK
Adjusting Sound Mode
Adjusting Sound Setting Mode
” appears in the
”
Performing a system
” (page 28) for details.
CAUTION
”
10
DXZ776USB
Basic Operations
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [
The mode that was previous active is
displayed.
2. Press and hold the [
second or longer to turn off the power for the
unit.
SRC
] button.
SRC
] button for 1
Selecting a mode
1. Press the [
operation mode.
2. Each time you press the [
operation mode changes in the following
order:
Radio ➜ CD/MP3/WMA/AAC ➜ USB ➜
(iPod BB) ➜ (CD changer) ➜ (DVD changer)
➜
(TV) ➜ AUX ➜ Radio...
∗
External equipment not connected with
CeNET is not displayed.
SRC
] button to change the
SRC
] button, the
Adjusting the volume
1. Push the [
to adjust the volume.
∗
The volume level is from 0 (minimum) to 33
(maximum).
VOL
] button upward or downward
Switching the display
Press and hold the [
or longer to select the desired display.
●
When the power is turned on
1. Each time you press and hold the [
button for 1 second or longer, the display
switches in the following order:
Action display ➜ Title display ➜ Clock time
display ➜ Action display...
●
When the power is turned off
1. Each time you press the [
clock time appears or disappears in the
display.
TITLE
] button for 1 second
TITLE
TITLE
] button, the
Mute
Use this function to turn off the sound
immediately.
1. Press the [] button.
The sound turns off and “
display.
2. Press the [] button again to cancel the
mute mode.
MUTE
” blinks in the
English
]
DXZ776USB
11
Basic Operations
English
Adjusting Sound Mode
To change sound mode
1. Press the [ ] button and select the sound
mode to adjust.
2. Push the [
rightward to select the “item
name”.
When speaker system is “
“
S-W VOLUME” ↔ “DZE” ↔ “P.EQ” ↔
“
BASS” ↔ “TREBLE” ↔ “S RESTORER”
↔ “HPF” ↔ “S-W LPF” ↔ “BALANCE” ↔
“FADER”
When speaker system is “3WAY”:
“S-W VOLUME” ↔ “DZE” ↔ “P.EQ” ↔
“BASS” ↔ “TREBLE” ↔ “S RESTORER”
↔ “BALANCE”
When speaker system is “2WAY”:
“DZE” ↔ “P.EQ” ↔ “BASS” ↔ “TREBLE”
↔ “S RESTORER” ↔ “BALANCE” ↔
“FADER”
3. Push the [P.CH] button upward or
downward to select the “desired setting
value”.
∗ In the case of item names appearing with
the “ENT” suffix after the item name, the
[] button must be pressed to display
the setting value.
∗ “P.EQ” can be adjusted only when the
“P.EQ ON/OFF” is set to “ON” (page 19)
and “EQ SELECT” is set to “P.EQ” (page
19).
∗ “BASS” and “TREBLE” can be adjusted
only when “DZE” is set to “DZE OFF” (page
12) and “EQ SELECT” is set to “B/T” (page
19).
∗ After completing settings, press the
button to return to the previous mode.
Note:
• During sound adjustment mode, if no operation
is performed for more than 10 seconds, this
mode can be canceled and return to the
previous mode.
SEEK PANEL
] leftward or
NORMAL
”:
[]
●
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
“
S-W VOLUME
“
SUB WOOFER
(page 19).
2-1. Select the “
3-1. Push the [
downward to change the output volume.
∗
The factory default setting is “0”.
(Setting range: +6 to –6)
●
Setting the Digital Z-Enhancer
This unit are provided with 3 types of sound
tone effects stored in memory. Select the one
you prefer.
∗
The factory default setting is “
2-1. Select the “
3-1. Press the [] button.
3-2. Push the [
rightward to select the tone effect. Each
time you push the [
effect changes in the following order:
“
DZE OFF” ↔ “DZE 1” ↔ “DZE 2” ↔ “DZE
3
”
DZE OFF
DZE 1
DZE 2
DZE 3
3-3. When the “
set, push the [
downward to change the DZE level from +3
to –3
∗
The factory default setting is “0”.
” can be adjusted only when
” is set to “ST” or “
S-W VOLUME
P.CH
] button upward or
DZE
”.
SEEK PANEL
SEEK PANEL
: no sound effect
: Suitable for genuine speakers
: Suitable for separate
speakers
: Suitable for co-axial speakers
DZE 1
”, “
DZE 2
P.CH
] button upward or
MONO
”.
DZE OFF
] leftward or
” or “
”.
], the tone
DZE 3
”
” is
12
DXZ776USB
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.