CLARION CAA188 User Manual
Printed in Japan 1999/7(CL.K) 284-8050-00
ø4✕12
ø4✕12
CCD camera
power supply box
CCD Camera Power Supply Box
CAA-188-200
Installation Instructions
1. Precautions
This equipment has been tested and f ound to comply with the limits for a Class B digital device , pursuant to P art 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interf erence in a residential installation.
This equipment generates , uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. Howe ver, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician
for help .
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL
VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
2. Package Contents
1.
CCD camera power supply box: ·············
2. Selector s witch:························ 1 bag
AUTO/MANU selector switch: ··················· 1
Mounting fitting: ········································1
Label: ························································1
3. Bag of accessories: ················· 1 bag
Electro taps:··············································2
Velcro: ······················································· 1
Velcro: ······················································· 1
1
4. Bag of accessories: ················· 1 bag
Clamp: ······················································1
Tapping screws: ········································ 4
5. Bag of accessories: ················· 1 bag
Connector cable (red): ······························ 1
Connector cable (light green): ·················· 1
Connector cable (black):··························· 1
Connector cable (red): ······························ 1
4. Mounting Procedure
4-1. Mounting the CCD Camera Power Supply Box
Mount the CCD camera power supply box in a location such as under a seat using either
the supplied tapping screws (ø4 x 12) or velcro.
■ Mounting Using Tapping Screws ■ Mounting Using Velcro
CCD camera
power supply box
Velcro
* Thoroughly wipe any dirt from the mounting
surface.
* Remove the separator from the back of the
velcro and apply it to the mounting surface.
Fig.4Fig.3
4-2. Mounting the AUTO/MANU Selector Switch
■ Mounting the Switch on the Dashboard
Mount the switch on the dashboard as sho wn in Fig. 6 using the supplied switch mounting
hole (Fig. 5).
Prepared ø12 hole
Label
Cosmetic cover (vehicle part)
3. Making Connections
3-1. System Connection Example
<1DIN TV, 2DIN TV>
Light green
Black
Red
To ACC power supply (12 V)
3-2. Connecting the Supplied Cables
Hook up the supplied connector cables as shown in Fig. 2.
Black
Red
GND
Light
green
To reverse gear
signal (12 V)
Fig.1
AUTO/MANU selector switch
White
Yellow
CCD camera
power supply box
For making connections to a TV
or video monitor equipped
with a video input jack
CCD camera
Cosmetic cover (vehicle part)
AUTO/MANU selector
switch cable
Selector switch knob
Prepared ø12 hole
Mounting nut
Upper
CAUTION
Mount so that notch on AUTO/MANU
selector switch faces downward.
Fig.5
Fig.6
■ Mounting the Switch Below the Dashboard
Assemble the AUTO/MANU selector switch as shown in Fig. 7 and mount it below the
dashboard. (See Fig. 8.)
Mounting fitting
Label
Nut
M
AUTO
AN
U
Harness
AUTO/MANU selector switch
Nut
Mounting fitting
Label
MANU
AUTO
A
Harness
AUTO/MANU selector switch
Clamp
3-3. Power Cable Connections
When connection cannot be made to the terminals, use the supplied Electro Tap to make
the connection as illustrated in the diagram.
From the vehicle side
Power cable
From the unit
Hook
Power cable
To reverse gear signal (12 V)
To ACC power supply (12 V)
Used to provide a 12 V power supply
to an additional device.
Fig.2
As illustrated in the diagram, the intermediate
cable is brought against the stopper and bent
back in the direction of the arrow.
The tip of the cable is
cut at a convenient
length.
Coupler connected to
another piece of
equipment
Pass the vehicle-side cable through and bend
back in the direction of the arrow.
Vehicle-side wire
GND
Latch
Not needed
Stopper
From the unit
Clamp
Tapping screws (ø4 x 12)
* Secure the switch harness to portion Aof the mounting
fitting using the clip.
Fig.8Fig.7
CAUTION
1. If harnesses will come into contact with the sharp edges of metal plates, or the like, protect
them using grommets or insulation tubes.
2. Before drilling any holes in a vehicle, make sure that there are no electrical wires, brake fluid
pipes, or the like, running behind to surface to be drilled.
3. When installation is complete, test the AUTO/MANU selector switch to make sure it works
properly.
Explanation of label indications
• MANU (manual) : The CCD camera image is given output
priority.
• AUTO (automatic) : Normally, the TV image is output. The
camera image is output when the
transmission is shifted into reverse.
Close with pliers until the latch engages.
Clarion Co., Ltd.
Unit-side cable
Vehicle-side cable
Loading...