Cisco Secure Network Server 3600 Series Hardware Installation Manual

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

Americas Headquarters

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]

800 553-NETS (6387)

Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright©1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com

go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any

other company. (1721R)

©

2019 Cisco Systems, Inc. All rights reserved.

CONTENTS

CHAPTER 1

CHAPTER 2

Cisco Secure Network Server 3600 Series Appliance Overview 1

Cisco Secure Network Server 3600 Series Appliances 1

Cisco SNS 3600 Series Appliance Hardware Specifications 1

External Features 3

Status LEDs and Buttons 5

Front Panel LEDs 5

Rear Panel LEDs 8

Internal Diagnostic LEDs 9

Serviceable Component Locations 10

Summary of Server Features 12

Installing the Appliance 15

Installation Warnings and Guidelines 15

Rack Requirements 16

Installing the Appliance in a Rack 17

Installing the Cable Management Arm (Optional) 19

CHAPTER 3

Reversing the Cable Management Arm (Optional) 20

Initial Setup 21

Connecting to the Appliance Locally For Setup 22

Connecting to the Appliance Remotely For Setup 23

Setting Up the System With the Cisco IMC Configuration Utility 24

Updating the BIOS and Cisco IMC Firmware 26

Accessing the System BIOS 26

Server Specifications 27

Server Specifications 27

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

iii

Contents

Physical Specifications 27

Environmental Specifications 27

Power Specifications 28

770 W AC Power Supply 28

1050 W AC Power Supply 29

1600 W AC Power Supply 30

1050 W DC Power Supply 30

Power Cord Specifications 31

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

iv

CHAPTER 1

Cisco Secure Network Server 3600 Series Appliance Overview

• Cisco Secure Network Server 3600 Series Appliances, on page 1

• Cisco SNS 3600 Series Appliance Hardware Specifications , on page 1

• External Features, on page 3

• Serviceable Component Locations, on page 10

• Summary of Server Features, on page 12

Cisco Secure Network Server 3600 Series Appliances

Cisco Secure Network Server (SNS) 3600 series appliances are designed to deliver high performance and
efficiency for a wide range of workloads.

Cisco SNS 3600 series appliances support the Unified Extensible Firmware Interface (UEFI) secure boot
feature. This feature ensures that only a Cisco-signed ISE image can be installed on the Cisco SNS 3600 series
appliances, and prevents installation of any unsigned operating system even with physical access to the device.
For example, generic operating systems, such as Red Hat Enterprise Linux or Microsoft Windows cannot
boot on this appliance.

Cisco SNS 3600 Series Appliance Hardware Specifications

The following table describes the hardware specifications of Cisco SNS 3600 series appliances.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

1

Cisco SNS 3600 Series Appliance Hardware Specifications

Table 1: Cisco SNS 3600 Series Appliance Hardware Specifications

Cisco Secure Network Server 3600 Series Appliance Overview

DiagramsHardware SpecificationsCisco SNS 3600 Series Appliance

Cisco SNS-3615-K9

Cisco SNS-3655-K9

• Cisco UCS C220 M5

• Intel Xeon Silver 2.1 GHz
4110, 8 CPU Cores, 16
Threads

• 32 GB RAM

• 1 x 600-GB disk

• RAID-0

• 6 GbE network interfaces

• For physical, environmental,
and power specifications, see

Server Specifications, on page
27

• Cisco UCS C220 M5

• Intel Xeon Silver 2.1 GHz
4116, 12 CPU Cores, 24
Threads

• 96 GB RAM

• 4 x 600-GB disk

Figure 1: Cisco SNS 3600 Series
Appliance Front Panel, on page 3

Figure 2: Cisco SNS 3600 Series
Appliance Rear Panel, on page 4

Cisco SNS-3695-K9

• RAID 10

• 6 GbE network interfaces

• For physical, environmental,
and power specifications, see

Server Specifications, on page
27

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

2

Cisco Secure Network Server 3600 Series Appliance Overview

External Features

DiagramsHardware SpecificationsCisco SNS 3600 Series Appliance

• Cisco UCS C220 M5

• Intel Xeon Silver 2.1 GHz
4116, 12 CPU Cores, 24
Threads

• 256 GB RAM

• 8 x 600-GB disk

• RAID 10

• 6 GbE network interfaces

• For physical, environmental,
and power specifications, see

Server Specifications, on page
27

External Features

This section describes the external features of Cisco SNS 3600 series appliance.

Cisco SNS 3600 Front Panel Features

The following figure shows the front panel features of Cisco SNS 3600 series appliance.

For definitions of LED states, see Front Panel LEDs, on page 5.

Figure 1: Cisco SNS 3600 Series Appliance Front Panel

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

3

External Features

Cisco Secure Network Server 3600 Series Appliance Overview

1

(SAS) and Serial Advanced Technology
Attachment (SATA) hard disk drives (HDDs) and
solid state drives (SSDs)

2

express (NVMe) based Peripheral Component
Interconnect Express (PCIe) SSDs

Cisco SNS 3600 Series Appliance Rear Panel Features

The following figure shows the rear panel features of Cisco SNS 3600 series appliance.

For definitions of LED states, see Rear Panel LEDs, on page 8.

Figure 2: Cisco SNS 3600 Series Appliance Rear Panel

Fan status LED7Drive bays 1 – 10 support Serial Attached SCSI

Network link activity LED8Drive bays 1 – 10 support Non-Volatile Memory

Temperature status LED9Power button or power status LED3

Pull-out asset tag10Unit identification button or LED4

11System status LED5

KVM connector

(used with KVM cable that provides one DB-15
VGA, one DB-9 serial, and two USB connectors)

-Power supply status LED6

1

Rear unit identification button or LED7Modular LAN-on-motherboard (mLOM) card bay

(x16 PCIe lane)

Power supplies (two, redundant as 1+1)8Two USB 3.0 ports2

3

9Dual 1-Gb or 10-Gb Ethernet ports (LAN1 and

LAN2)

The dual LAN ports can support 1 Gbps or 10 Gbps

PCIe riser 2 or slot 2 (x16 lane)

Includes PCIe cable connectors for front-loading
NVMe SSDs (x8 lane)

depending on the link partner capability.

PCIe riser 1 or slot 1 (x16 lane)10VGA video port (DB-15 connector)4

Threaded holes for dual-hole grounding lug111-Gb Ethernet dedicated management port5

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

4

Cisco Secure Network Server 3600 Series Appliance Overview

Status LEDs and Buttons

This section contains information for interpreting front, rear, and internal LED states.

Front Panel LEDs

The following figure shows the front panel LEDs of Cisco SNS 3600 series appliance.

Figure 3: Front Panel LEDs

Status LEDs and Buttons

-Serial port (RJ-45 connector)6

Table 2: Front Panel LEDs

1

SAS

SAS/SATA drive fault

Note

SAS/SATA drive activity LED2

SAS

NVMe SSD drive tray LEDs have different
behavior than SAS/SATA drive trays.

StatesLED Name

• Off—The hard drive is operating properly.

• Amber—Drive fault detected.

• Amber, blinking—The device is rebuilding.

• Amber, blinking with one-second interval—Drive
locate function activated in the software.

• Off—There is no hard drive in the hard drive tray (no
access, no fault).

• Green—The hard drive is ready.

• Green, blinking—The hard drive is reading or writing
data.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

5

Front Panel LEDs

Cisco Secure Network Server 3600 Series Appliance Overview

1

NVMe

NVMe

NVMe SSD drive fault

Note

NVMe SSD drive tray LEDs have different
behavior than SAS/SATA drive trays.

NVMe SSD activity2

Power button or LED3

• Off—The drive is not in use and can be safely
removed.

• Green—The drive is in use and functioning properly.

• Green, blinking—The driver is initializing following
insertion or the driver is unloading following an eject
command.

• Amber—The drive has failed.

• Amber, blinking—Drive locate function activated in
the software.

• Off—No drive activity.

• Green, blinking—There is drive activity.

• Off—There is no AC power to the server.

• Amber—The server is in standby power mode. Power
is supplied only to the Cisco Integrated Management
Controller (Cisco IMC) and some motherboard
functions.

• Green—The server is in main power mode. Power is
supplied to all server components.

Unit identification4

• Off—The unit identification function is not in use.

• Blue, blinking—The unit identification function is
activated.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

6

Cisco Secure Network Server 3600 Series Appliance Overview

Front Panel LEDs

System health5

• Green—The server is running in normal operating
condition.

• Green, blinking—The server is performing system
initialization and memory check.

• Amber, steady—The server is in a degraded
operational state (minor fault). For example:

• Power supply redundancy is lost.

• CPUs are mismatched.

• At least one CPU is faulty.

• At least one dual in-line memory module
(DIMM) is faulty.

• At least one drive in a RAID configuration failed.

• Amber, 2 blinks—There is a major fault with the
system board.

• Amber, 3 blinks—There is a major fault with the
DIMMs.

• Amber, 4 blinks—There is a major fault with the
CPUs.

Power supply status6

• Green—All power supplies are operating normally.

• Amber, steady—One or more power supplies are in
a degraded operational state.

• Amber, blinking—One or more power supplies are
in a critical fault state.

Fan status7

• Green—All fan modules are operating properly.

• Amber, blinking—One or more fan modules breached
the non-recoverable threshold.

Network link activity8

• Off—The Ethernet Lights Out Management (LOM)
port link is idle.

• Green—One or more Ethernet LOM ports are
link-active, but there is no activity.

• Green, blinking—One or more Ethernet LOM ports
are link-active, with activity.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

7

Rear Panel LEDs

Cisco Secure Network Server 3600 Series Appliance Overview

Temperature status9

Rear Panel LEDs

Table 3: Rear Panel LEDs

1

• Green—The server is operating at normal temperature.

• Amber, steady—One or more temperature sensors
breached the critical threshold.

• Amber, blinking—One or more temperature sensors
breached the non-recoverable threshold.

The following figure shows the rear panel LEDs of Cisco SNS 3600 series appliance.

Figure 4: Rear Panel LEDs

StatesLED Name

1-Gb or 10-Gb Ethernet link speed (on
both LAN1 and LAN2)

• Off—Link speed is 100 Mbps.

• Amber—Link speed is 1 Gbps.

• Green—Link speed is 10 Gbps.

2

1-Gb or 10-Gb Ethernet link status (on
both LAN1 and LAN2)

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the
active link.

3

1-Gb Ethernet dedicated management
link speed

• Off—Link speed is 10 Mbps.

• Amber—Link speed is 100 Mbps.

• Green—Link speed is 1 Gbps.

4

1-Gb Ethernet dedicated management
link status

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the
active link.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

8

Cisco Secure Network Server 3600 Series Appliance Overview

Internal Diagnostic LEDs

Rear unit identification5

• Off—The unit identification function is not
in use.

• Blue, blinking—The unit identification
function is activated.

6

Power supply status (one LED for each
power supply unit)

AC power supplies:

• Off—No AC input (12 V main power off,
12 V standby power off).

• Green, blinking—12 V main power off; 12
V standby power on.

• Green, solid—12 V main power on; 12 V
standby power on.

• Amber, blinking—Warning threshold
detected, but 12 V main power on.

• Amber, solid—Critical error detected; 12
V main power off (for example,
over-current, over-voltage, or
over-temperature failure).

DC power supplies:

Internal Diagnostic LEDs

The server has internal fault LEDs for CPUs, DIMMs, and fan modules.

• Off—No DC input (12 V main power off,
12 V standby power off).

• Green, blinking—12 V main power off; 12
V standby power on.

• Green, solid—12 V main power on; 12 V
standby power on.

• Amber, blinking—Warning threshold
detected, but 12 V main power on.

• Amber, solid—Critical error detected; 12
V main power off (for example,
over-current, over-voltage, or
over-temperature failure).

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

9

Serviceable Component Locations

Figure 5: Internal Diagnostic LED Locations

Cisco Secure Network Server 3600 Series Appliance Overview

1

connector on the motherboard)

• Amber—Fan has a fault or is not fully seated.

• Green—Fan is OK.

2

the motherboard).

These LEDs operate only when the server is in
standby power mode.

• Amber—CPU has a fault.

• Off—CPU is OK.

3Fan module fault LEDs (one behind each fan

-CPU fault LEDs (one behind each CPU socket on

Serviceable Component Locations

This section describes the field-replaceable components and service related items. The view in the following
figure shows the appliance with the top cover removed.

DIMM fault LEDs (one behind each DIMM socket
on the motherboard)

These LEDs operate only when the server is in
standby power mode.

• Amber—DIMM has a fault.

• Off—DIMM is OK.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

10

Cisco Secure Network Server 3600 Series Appliance Overview

Figure 6: Serviceable Component Locations

Serviceable Component Locations

1

10Front-loading drive bays 1–10 support SAS/SATA

drives

11Cooling fan modules (seven, hot-swappable)2

Power supplies (hot-swappable when redundant as
1+1)

Trusted platform module (TPM) socket on
motherboard (not visible in this view)

12Supercap unit mounting bracket (RAID backup)3

PCIe riser 2 or slot 2 (half-height, x16 lane)

Includes PCIe cable connectors for front-loading
NVMe SSDs (x8 lane)

13DIMM sockets on motherboard (12 per CPU)4

PCIe riser 1 or slot 1 (full-height, x16 lane)

Includes socket for Micro-SD card

14CPUs and heatsinks (up to two)5

Modular LOM (mLOM) card bay on chassis floor
(x16 PCIe lane), not visible in this view

6

15Mini storage module socket

Supports either an SD card module with two SD
card slots; or an M.2 module with two NVMe or
SATA M.2 SSD slots.

16Chassis intrusion switch (optional)7

Modular RAID (mRAID) riser, can optionally be a
riser that supports either:

• Hardware RAID controller card

• Interposer card for embedded SATA RAID

PCIe cable connectors for front-loading NVMe SSDs
on PCIe riser 2

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

11

Summary of Server Features

Summary of Server Features

The following table lists a summary of server features.

Cisco Secure Network Server 3600 Series Appliance Overview

Micro-SD card socket on PCIe riser 117Internal USB 3.0 port on motherboard8

-RTC battery, vertical socket9

DescriptionFeature

One rack-unit (1RU) chassisChassis

Central Processor

Baseboard management

Network and management I/O

• Intel Xeon 2.1 GHz 4110

• Intel Xeon 2.1 GHz 4116

24 DDR4 DIMM sockets on the motherboard (12 each CPU)Memory

Multi-bit error protection is supportedMulti-bit error protection

Board management controller (BMC), running Cisco Integrated
Management Controller (Cisco IMC) firmware.

Depending on your Cisco IMC settings, Cisco IMC can be
accessed through the 1-Gb dedicated management port, the
1-Gb/10-Gb Ethernet LAN ports, or a Cisco virtual interface card.

Rear panel:

• One 1-Gb Ethernet dedicated management port (RJ-45
connector)

• Two 1-Gb/10-Gb BASE-T Ethernet LAN ports (RJ-45
connectors)

The dual LAN ports can support 1 Gbps or 10 Gbps
depending on the link partner capability.

• One RS-232 serial port (RJ-45 connector)

Modular LOM

12

• One Video Graphics Array (VGA) connector port (DB-15
connector)

• Two USB 3.0 ports

Front panel:

• One front-panel keyboard/video/mouse (KVM) connector
that is used with the KVM cable, which provides two USB

2.0, one VGA, and one DB-9 serial connector.

One dedicated socket (x16 PCIe lane) that can be used to add an
mLOM card for additional rear-panel connectivity.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

Cisco Secure Network Server 3600 Series Appliance Overview

Summary of Server Features

DescriptionFeature

WoL

Power

ACPI

InfiniBand

Storage, internal

The two 1-Gb/10-Gb BASE-T Ethernet LAN ports support the
wake-on-LAN (WoL) standard.

Two power supplies, redundant as 1+1:

• AC power supplies 770 W AC each

• AC power supplies 1050 W AC each

• AC power supplies 1600 W AC each

• DC power supplies 1050 W DC each

Do not mix power supply types or wattages in the server.

The advanced configuration and power interface (ACPI) 4.0
standard is supported.

Seven hot-swappable fan modules for front-to-rear cooling.Cooling

Two horizontal PCIe expansion slots on a PCIe riser assembly.PCIe I/O

The PCIe bus slots in this server support the InfiniBand
architecture.

The following internal storage options are available:

• One USB port on the motherboard.

Storage management

RAID backup

• Mini-storage module socket, optionally with either:

• SD card module. Supports up to two SD cards.

• M.2 SSD module. Supports either two SATA M.2 SSDs
or two NVMe M.2 SSDs.

• One micro-SD card socket on PCIe riser 1.

The appliance has a dedicated internal mRAID riser that supports
one of the following storage-controller options:

• A PCIe-style Cisco modular RAID controller card
(SAS/SATA).

• A PCIe-style interposer card for the server’s embedded
SATA RAID controller.

The appliance has a mounting bracket near the cooling fans for
the supercap unit that is used with the Cisco modular RAID
controller card.

Integrated VGA video.Integrated video

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

13

Summary of Server Features

Cisco Secure Network Server 3600 Series Appliance Overview

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

14

Installing the Appliance

• Installation Warnings and Guidelines, on page 15

• Rack Requirements, on page 16

• Installing the Appliance in a Rack, on page 17

• Initial Setup, on page 21

• Updating the BIOS and Cisco IMC Firmware, on page 26

• Accessing the System BIOS, on page 26

Installation Warnings and Guidelines

CHAPTER 2

Warning

Warning

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each
warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of: 35° C (95° F).

Statement 1047

The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device.

Statement 1019

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

15

Rack Requirements

Installing the Appliance

Warning

Warning

Warning

Caution

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 250 V, 15 A.

Statement 1005

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only through the use of a special tool, lock, and key, or other means of security.

Statement 1017

Rack the appliance using rail kits to ensure proper airflow. Physically placing the units on top of one another
or stacking without the use of the rail kits, blocks the air vents on the top, which could result in overheating,
higher fan speeds, and higher power consumption. We recommend that you mount your appliance on rail kits
while installing in the rack because these rails provide the minimal spacing required between the units. No
additional spacing is required when you mount the units using rail kits.

Follow these guidelines while installing the appliance:

• Ensure that there is adequate space around the appliance to allow for easy access and for adequate airflow.

• Ensure that the air-conditioning meets the thermal requirements listed in the Environmental Specifications,

on page 27.

• Ensure that the cabinet or rack meets the requirements listed in the Rack Requirements, on page 16.

• Ensure that the site power meets the power requirements listed in the Power Specifications, on page 28.
If available, you can use an uninterruptible power supply (UPS) to protect against power failures.

Rack Requirements

The rack must be of the following type:

• A standard 19-inch (48.3 cm) wide, four-post EIA rack, with mounting posts that conform to English
universal hole spacing, per section 1 of ANSI/EIA-310-D-1992.

• The rack-post holes can be square 0.38 inch (9.6 mm), round 0.28 inch (7.1 mm), #12-24 UNC, or #10-32
UNC when you use the Cisco-supplied slide rails.

• The minimum vertical rack space per server must be one rack unit (RU), which is equal to 1.75 inch
(44.45 mm).

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

16

Installing the Appliance

Rack Installation Tools Required

The slide rails sold by Cisco Systems for this server do not require tools for installation.

Slide Rail and Cable Management Arm Dimensions

The slide rails have an adjustment range of 24 to 36 inches (610 to 914 mm).

The optional cable management arm (CMA) adds additional length requirements:

• The additional distance from the rear of the appliance to the rear of the CMA is 5.4 inches (137.4 mm).

• The total length of the appliance including the CMA is 35.2 inches (894 mm).

Installing the Appliance in a Rack

Installing the Appliance in a Rack

Warning

Step 1 Attach the inner rails to the sides of the appliance:

a) Align an inner rail with one side of the appliance so that the three keyed slots in the rail align with the three pegs on

b) Set the keyed slots over the pegs, and then slide the rail toward the front to lock it in place on the pegs. The front slot

c) Install the second inner rail to the opposite side of the appliance.

Figure 7: Attaching the Inner Rail to the Side of the Appliance

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.

Statement 1006

the side of the appliance.

has a metal clip that locks over the front peg.

Locking clip on front of inner rail2Front of appliance1

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

17

Installing the Appliance

Installing the Appliance in a Rack

Step 2 Open the front securing plate on both slide-rail assemblies. The front end of the slide-rail assembly has a spring-loaded

securing plate that must be open before you can insert the mounting pegs into the rack-post holes.

On the outside of the assembly, push the green-arrow button toward the rear to open the securing plate.

Figure 8: Front Securing Mechanism, Inside of Front End

2

securing plate

Step 3 Install the outer slide rails into the rack:

a) Align one slide-rail assembly front end with the front rack-post holes that you want to use.

The slide rail front-end wraps around the outside of the rack post and the mounting pegs enter the rack-post holes
from the outside-front.

Note

The rack post must be between the mounting pegs and the open securing plate.

b) Push the mounting pegs into the rack-post holes from the outside-front.
c) Press the securing plate release button, marked Push. The spring-loaded securing plate closes to lock the pegs in

place.

d) Adjust the slide-rail length, and then push the rear mounting pegs into the corresponding rear rack-post holes.

The rear mounting pegs enter the rear rack-post holes from the inside of the rack post.

e) Attach the second slide-rail assembly to the opposite side of the rack. Ensure that the two slide-rail assemblies are at

the same height and are level front-to-back.

f) Pull the inner slide rails on each assembly out toward the rack front until they hit the internal stops and lock in place.

Step 4 Insert the appliance into the slide rails:

3Front mounting pegs1

Securing plate shown pulled back to the open
position

-Rack post between mounting pegs and opened

Caution

This appliance can weigh up to 60 pounds (27 kilograms) when fully loaded with components. We recommend
that you use a minimum of two people or a mechanical lift when lifting the server. Attempting this procedure
alone could result in personal injury or equipment damage.

a) Align the rear ends of the inner rails that are attached to the appliance sides with the front ends of the empty slide

rails on the rack.
b) Push the inner rails into the slide rails on the rack until they stop at the internal stops.
c) Slide the inner-rail release clip toward the rear on both inner rails, and then continue pushing the appliance into the

rack until its front slam-latches engage with the rack posts.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

18

Installing the Appliance

Figure 9: Inner-Rail Release Clip

Installing the Cable Management Arm (Optional)

Outer slide rail attached to rack post3Inner-rail release clip1

2

-Inner rail attached to appliance and inserted

into outer slide rail

Step 5 (Optional) Secure the appliance in the rack by using the two screws that are provided with the slide rails. Perform this

step if you plan to move the rack with appliance installed.

With the appliance fully pushed into the slide rails, open a hinged slam latch lever on the front of the appliance and insert
a screw through the hole that is under the lever. The screw threads into the static part of the rail on the rack post and
prevents the server from being pulled out. Repeat for the opposite slam latch.

Installing the Cable Management Arm (Optional)

Note

The cable management arm (CMA) is reversible left-to-right. To reverse the CMA, see Reversing the Cable

Management Arm (Optional), on page 20 before installation.

Step 1 With the appliance pushed fully into the rack, slide the CMA tab of the CMA arm that is farthest from the appliance onto

the end of the stationary slide rail that is attached to the rack post. Slide the tab over the end of the rail until it clicks and
locks.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

19

Reversing the Cable Management Arm (Optional)

Figure 10: Attaching the CMA to the Rear Ends of the Slide Rails

Installing the Appliance

1

3CMA tab on arm farthest from appliance

attaches to end of stationary outer slide rail.

2

CMA tab on width-adjustment slider attaches
to end of stationary outer slide rail.

Rear of appliance4CMA tab on arm closest to the appliance
attaches to end of inner slide rail attached to
appliance.

Step 2 Slide the CMA tab that is closest to the appliance over the end of the inner rail that is attached to the appliance. Slide the

tab over the end of the rail until it clicks and locks.

Step 3 Pull out the width-adjustment slider that is at the opposite end of the CMA assembly until it matches the width of your

rack.

Step 4 Slide the CMA tab that is at the end of the width-adjustment slider onto the end of the stationary slide rail that is attached

to the rack post. Slide the tab over the end of the rail until it clicks and locks.

Step 5 Open the hinged flap at the top of each plastic cable guide and route your cables through the cable guides as desired.

Reversing the Cable Management Arm (Optional)

Step 1 Rotate the entire Cable Management Arm (CMA) assembly 180 degrees, left-to-right. The plastic cable guides must

remain pointing upward.

Step 2 Flip the tabs at the ends of the CMA arms so that they point toward the rear of the appliance.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

20

Installing the Appliance

Initial Setup

Step 3 Pivot the tab that is at the end of the width-adjustment slider. Depress and hold the metal button on the outside of the tab

and pivot the tab 180 degrees so that it points toward the rear of the appliance.

Figure 11: Reversing the CMA

Initial Setup

Note

This section describes how to connect to the system for initial setup.

Appliance Default Settings

The appliance is shipped with the following default settings:

Metal button on outside of tab2CMA tab on end of width-adjustment slider1

• The NIC mode is Shared LOM EXT.

Shared LOM EXT mode enables the 1-Gb/10-Gb Ethernet ports and the ports on any installed Cisco
virtual interface card (VIC) to access the Cisco IMC. If you want to use the 10/100/1000 dedicated
management ports to access Cisco IMC, you can change the NIC mode as described in Setting Up the

System With the Cisco IMC Configuration Utility, on page 24.

• The NIC redundancy is Active-Active. All Ethernet ports are utilized simultaneously.

• DHCP is enabled.

• IPv4 is enabled.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

21

Connecting to the Appliance Locally For Setup

Connection Methods

There are two methods for connecting to the system for initial setup:

• Local setup—Use this procedure if you want to connect a keyboard and monitor directly to the system
for setup. This procedure can use a KVM cable (Cisco PID N20-BKVM) or the ports on the rear of the
appliance.

• Remote setup—Use this procedure if you want to perform setup through your dedicated management
LAN.

Note

Installing the Appliance

To configure the system remotely, you must have a DHCP server on the same
network as the system. Your DHCP server must be preconfigured with the range
of MAC addresses for this server node. The MAC address is printed on a label
that is on the pull-out asset tag on the front panel. This server node has a range
of six MAC addresses assigned to the Cisco IMC. The MAC address printed on
the label is the beginning of the range of six contiguous MAC addresses.

Connecting to the Appliance Locally For Setup

This procedure requires the following equipment:

• VGA monitor

• USB keyboard

• One of the following:

• Supported Cisco KVM cable (Cisco PID N20-BKVM)

• USB cable and VGA DB-15 cable

Step 1 Attach a power cord to each power supply in your appliance, and then attach each power cord to a grounded power outlet.

Wait for approximately two minutes to let the appliance boot to standby power during the first bootup. You can verify
system power status by looking at the system Power Status LED on the front panel. The system is in standby power mode
when the LED is amber.

Step 2 Connect a USB keyboard and VGA monitor to the appliance using one of the following methods:

• Connect an optional KVM cable (Cisco PID N20-BKVM) to the KVM connector on the front panel. Connect your
USB keyboard and VGA monitor to the KVM cable.

• Connect a USB keyboard and VGA monitor to the corresponding connectors on the rear panel.

Step 3 Open the Cisco IMC Configuration Utility:

a) Press and hold the front panel power button for four seconds to boot the appliance.
b) During bootup, press F8 when prompted to open the Cisco IMC Configuration Utility.

Note

When you open the Cisco IMC Configuration Utility for the first time, you are prompted to change the
default password. The default password is password. The Strong Password feature is enabled.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

22

Installing the Appliance

Connecting to the Appliance Remotely For Setup

The following are the requirements for Strong Password:

• The password can have a minimum of 8 characters and maximum 14 characters.

• The password must not contain the user’s name.

• The password must contain characters from three of the following categories:

• English uppercase letters (A through Z)

• English lowercase letters (a through z)

• Base 10 digits (0 through 9)

• Non-alphabetic characters !, @, #, $, %, ^, &, *, -, _, =, “

Step 4 Continue with Setting Up the System With the Cisco IMC Configuration Utility, on page 24.

Connecting to the Appliance Remotely For Setup

This procedure requires the following equipment:

• One RJ-45 Ethernet cable that is connected to your management LAN.

Note

To configure the system remotely, you must have a DHCP server on the same network as the system. Your
DHCP server must be preconfigured with the range of MAC addresses for this server node. The MAC address
is printed on a label that is on the pull-out asset tag on the front panel. This server node has a range of six
MAC addresses assigned to the Cisco IMC. The MAC address printed on the label is the beginning of the
range of six contiguous MAC addresses.

Step 1 Attach a power cord to each power supply in your appliance, and then attach each power cord to a grounded power outlet.

Wait for approximately two minutes to let the appliance boot to standby power during the first bootup. You can verify
system power status by looking at the system Power Status LED on the front panel. The system is in standby power mode
when the LED is amber.

Step 2 Plug your management Ethernet cable into the dedicated management port on the rear panel.

Step 3 Allow your preconfigured DHCP server to assign an IP address to the server node.

Step 4 Use the assigned IP address to access and log in to the Cisco IMC for the server node.

Note

The default user name for the server is admin. The default password is password.

Step 5 From the Cisco IMC Server Summary page, click Launch KVM Console.

A separate KVM console window opens.

Step 6 From the Cisco IMC Summary page, click Power Cycle Server.

The system reboots.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

23

Setting Up the System With the Cisco IMC Configuration Utility

Step 7 Select the KVM console window.

Step 8 When prompted, press F8 to enter the Cisco IMC Configuration Utility.

Installing the Appliance

Note

When you open the Cisco IMC Configuration Utility for the first time, you are prompted to change the default
password. The default password is password. The Strong Password feature is enabled.

The following are the requirements for Strong Password:

• The password can have a minimum of 8 characters and maximum 14 characters.

• The password must not contain the user’s name.

• The password must contain characters from three of the following categories:

• English uppercase letters (A through Z)

• English lowercase letters (a through z)

• Base 10 digits (0 through 9)

• Non-alphabetic characters !, @, #, $, %, ^, &, *, -, _, =, “

Step 9 Continue with Setting Up the System With the Cisco IMC Configuration Utility, on page 24.

Setting Up the System With the Cisco IMC Configuration Utility

Before you begin

The following procedure is performed after you connect to the system and open the Cisco IMC Configuration
Utility.

Step 1 Set the NIC mode to choose which ports to use to access Cisco IMC for server management:

• Shared LOM EXT (default)—This is the shared LOM extended mode, the factory-default setting. With this mode,
the Shared LOM and Cisco Card interfaces are both enabled. If you select this option, you must select the default
Active-Active NIC redundancy setting in the following step.

• Shared LOM—The 1-Gb/10-Gb Ethernet ports are used to access Cisco IMC. If you select this option, you must
select Active-Active or Active-standby NIC redundancy setting in the following step.

• Dedicated—The dedicated management port is used to access Cisco IMC. If you select this option, you must select
the None NIC redundancy setting in the following step.

• Cisco Card—The Virtual Interface Card (VIC) ports are used to access the Cisco IMC. If you select this option,
you must select Active-Active or Active-standby NIC redundancy setting in the following step.

• VIC Slot—Only if you use the Cisco Card NIC mode, you must select this setting to match where your VIC is
installed. You can select Riser1, Riser2, or Flex-LOM (the mLOM slot).

• If you select Riser1, you must install the VIC in slot 1.

• If you select Riser2, you must install the VIC in slot 2.

• If you select Flex-LOM, you must install an mLOM-style VIC in the mLOM slot.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

24

Installing the Appliance

Setting Up the System With the Cisco IMC Configuration Utility

Step 2 Choose one of the following options for NIC redundancy:

• None—The Ethernet ports operate independently and do not fail over if there is a problem. This setting can be
used only with the Dedicated NIC mode.

• Active-standby—If an active Ethernet port fails, traffic fails over to a standby port. Shared LOM and Cisco Card
modes can use Active-standby or Active-active settings.

• Active-active (default)—All Ethernet ports are used simultaneously. You must use only this NIC redundancy
setting if you have selected the Shared LOM EXT mode. Shared LOM and Cisco Card modes can use Active-standby
or Active-active settings.

Step 3 Choose whether to enable DHCP for dynamic network settings, or to enter static network settings.

Note

Before you enable DHCP, you must preconfigure your DHCP server with the range of MAC addresses for
this server. The MAC address is printed on a label on the rear of the server. This server has a range of six
MAC addresses assigned to Cisco IMC. The MAC address printed on the label is the beginning of the range
of six contiguous MAC addresses.

The Static IPv4 and IPv6 Settings include the following:

• Cisco IMC IP address—For IPv6, valid values are 1 - 127.

• Gateway—For IPv6, if you do not know the gateway, you can set it as none by entering :: (two colons).

• Preferred DNS Server Address—For IPv6, you can set this as none by entering :: (two colons).

Step 4 (Optional) Configure VLAN settings.

Step 5 (Optional) Set a hostname for the server.

Step 6 (Optional) Enable dynamic DNS and set a dynamic DNS (DDNS) domain.

Step 7 (Optional) If you check the Factory Default check box, the server reverts to the factory defaults.

Step 8 (Optional) Set a default user password.

Note

The factory default username for the server is admin. The default password is password.

Step 9 (Optional) Enable auto-negotiation of port settings or set the port speed and duplex mode manually.

Note

Auto-negotiation is applicable only when you use the Dedicated NIC mode. Auto-negotiation sets the port
speed and duplex mode automatically based on the switch port to which the server is connected. If you disable
auto-negotiation, you must set the port speed and duplex mode manually.

Step 10 (Optional) Reset port profiles and the port name.

Step 11 Press F5 to refresh the settings that you made. You might have to wait about 45 seconds until the new settings appear

and the message, “Network settings configured” is displayed before you reboot the server in the next step.

Step 12 Press F10 to save your settings and reboot the server.

Note

If you chose to enable DHCP, the dynamically assigned IP and MAC addresses are displayed during bootup.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

25

Updating the BIOS and Cisco IMC Firmware

Updating the BIOS and Cisco IMC Firmware

Installing the Appliance

Caution

When you upgrade the BIOS firmware, you must also upgrade the Cisco IMC firmware to the same version
or the server will not boot. Do not power off the server until the BIOS and Cisco IMC firmware are matching
or the server will not boot.

The server uses firmware obtained from and certified by Cisco. Cisco provides release notes with each firmware
image.

You can upgrade the Cisco IMC and BIOS firmware by using the Cisco IMC GUI or CLI interface.

Accessing the System BIOS

Step 1 Enter the BIOS Setup Utility by pressing the F2 key when prompted during bootup.

Note

Step 2 Use the arrow keys to select the BIOS menu page.

Step 3 Highlight the field to be modified by using the arrow keys.

Step 4 Press Enter to select the field that you want to change, and then modify the value in the field.

Step 5 Press the right arrow key until the Exit menu screen is displayed.

Step 6 Follow the instructions on the Exit menu screen to save your changes and exit the setup utility (or press F10). You can

exit without saving changes by pressing Esc.

The version and build of the current BIOS are displayed on the Main page of the utility.

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

26

Server Specifications

• Server Specifications, on page 27

• Power Specifications, on page 28

• Power Cord Specifications, on page 31

Server Specifications

This chapter lists the physical, environmental, and power specifications for the server.

Physical Specifications

The following table lists the physical specifications for the server.

Table 4: Physical Specifications

SpecificationDescription

CHAPTER 3

1.7 in. (43.2 mm)Height

16.9 in. (429.0 mm)Width

Depth
(length)

Weight

Server only: 29.5 in. (740.3 mm)

Server with slide rail: 31.0 in. (787.4 mm)

Maximum: 37.5 lb. (17.0 Kg)

Minimum: 29.0 lb. (13.2 Kg)

Environmental Specifications

The following table lists the environmental requirements and specifications for the server.

Table 5: Environmental Specifications

SpecificationDescription

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

27

Power Specifications

Server Specifications

Temperature, operating

(when the server is stored or transported)

(when the server is stored or transported)

(when the server is stored or transported)

Measure A-weighted per ISO7779 LwAd (Bels)

Operation at 73°F (23°C)

Measure A-weighted per ISO7779 LpAm (dBA)

41 to 95°F (5 to 35°C)

Derate the maximum temperature by 1°C per every 305 meters of altitude above
sea level.

–40 to 149°F (–40 to 65°C)Temperature, Non-operating

10 to 90%Humidity (RH), operating

5 to 93%Humidity (RH), non-operating

0 to 10,000 feetAltitude, operating

0 to 40,000 feetAltitude, non-operating

5.5Sound power level

40Sound pressure level

Operation at 73°F (23°C)

Power Specifications

Note

Do not mix power supply types or wattages. Both power supplies must be identical.

The power specifications for the supported power supply options are listed in the following sections.

770 W AC Power Supply

This section lists the specifications for each 770 W AC power supply.

Table 6: 770 W AC Specifications

SpecificationDescription

AC Input Voltage

Nominal range: 100–120 VAC, 200–240 VAC

(Range: 90–132 VAC, 180–264 VAC)

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

28

Server Specifications

1050 W AC Power Supply

AC Input Frequency

Maximum AC Input current

Nominal range: 50 to 60Hz

(Range: 47–63 Hz)

9.5 A at 100 VAC

4.5 A at 208 VAC

950 VA at 100 VACMaximum input volt-amperes

15 A (sub-cycle duration)Maximum inrush current

12 ms at 770 WMaximum hold-up time

770 WMaximum output power per PSU

12 VDCPower supply output voltage

12 VDCPower supply standby voltage

Climate Savers Platinum Efficiency (80Plus Platinum certified)Efficiency rating

RSP2Form factor

IEC320 C14Input connector

1050 W AC Power Supply

This section lists the specifications for each 1050 W AC power supply.

Table 7: 1050 W AC Specifications

SpecificationDescription

AC Input Voltage

AC Input Frequency

Maximum AC Input current

Maximum output power per PSU

Nominal range: 100–120 VAC, 200–240 VAC

(Range: 90–132 VAC, 180–264 VAC)

Nominal range: 50 to 60Hz

(Range: 47–63 Hz)

12.5 A at 100 VAC

6.0 A at 208 VAC

1250 VA at 100 VACMaximum input volt-amperes

15 A (sub-cycle duration)Maximum inrush current

12 ms at 1050 WMaximum hold-up time

800 W at 100–120 VAC

1050 W at 200–240 VAC

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

29

1600 W AC Power Supply

12 VDCPower supply output voltage

12 VDCPower supply standby voltage

Climate Savers Platinum Efficiency (80Plus Platinum certified)Efficiency rating

RSP2Form factor

IEC320 C14Input connector

1600 W AC Power Supply

This section lists the specifications for each 1600 W AC power supply.

Table 8: 1600 W AC Specifications

SpecificationDescription

Server Specifications

AC Input Voltage

AC Input Frequency

Nominal range: 200–240 VAC

(Range: 180–264 VAC)

Nominal range: 50 to 60Hz

(Range: 47–63 Hz)

9.5 A at 200 VACMaximum AC Input current

1250 VA at 200 VACMaximum input volt-amperes

30 A at 35° CMaximum inrush current

80 ms at 1600 WMaximum hold-up time

1600 W at 200–240 VACMaximumoutput power per PSU

12 VDCPower supply output voltage

12 VDCPower supply standby voltage

Climate Savers Platinum Efficiency (80Plus Platinum certified)Efficiency rating

RSP2Form factor

IEC320 C14Input connector

1050 W DC Power Supply

This section lists the specifications for each 1050 W DC power supply.

Table 9: 1050 W DC Specifications

SpecificationDescription

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

30

Server Specifications

Power Cord Specifications

DC Input Voltage

Maximum output power per PSU

Nominal range: -48 to -60 VDC

(Range: -40 to -72 VDC)

32 A at -40 VDCMaximum DC input current

1234 WMaximum input wattage

35 A (sub-cycle duration)Maximum inrush current

5 ms at 100% load (1050 W main and 36 W standby)Maximum hold-up time

1050 W on 12 VDC main power

36 W on 12 VDC standby power

12 VDCPower supply output voltage

12 VDCPower supply standby voltage

≥ 92% at 50% loadEfficiency rating

RSP2Form factor

Fixed 3-wire blockInput connector

Power Cord Specifications

Each power supply in the appliance has a power cord. Standard power cords or jumper power cords are
available for connection to the appliance. The shorter jumper power cords, for use in racks, are available as
an optional alternative to the standard power cords.

Note

Only the approved power cords or jumper power cords listed below are supported.

Table 10: Supported Power Cords

Description

DC power cord, -48 VDC, 40 A, 8 AWG

Three-socket Mini-Fit connector to three-wire

AC power cord, 10 A; C13 to C14, recessed receptacle

Length
(Feet)

Length
(Meters)

3.511.7CAB-48DC-40A-8AWG

3.09.8CAB-C13-C14-AC

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

31

Power Cord Specifications

AC power cord, 250 V, 10 A

(Argentina)

AC Power Cord, C13 to C14

(Japan PSE Mark)

AC Power Cord, 250 V, 10 A; CEE 7/7 Plug

(Europe)

AC Power Cord, 250 V, 10 A

(Israel )

Server Specifications

2.58.2CAB-250V-10A-AR

2.06.6CAB-C13-C14-2M-JP

2.58.2CAB-9K10A-EU

2.58.2CAB-250V-10A-IS

AC power cord, 250 V, 10 A

(PR China)

AC power cord, 250 V, 10 A

(Taiwan)

AC cabinet jumper power cord, 250, 10 A,

C13 to C14

AC cabinet jumper power cord, 250 V, 10 A,

C13 to C14

AC power cord, 250 V, 10 A, 3112 plug

(Australia)

2.58.2CAB-250V-10A-CN

2.37.5CAB-ACTW

0.682.2CAB-C13-CBN

2.06.6CAB-C13-C14-2M

2.58.2CAB-9K10A-AU

2.58.2CAB-N5K6A-NA

AC power cord, 200/240 V, 6 A

(North America)

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

32

Server Specifications

AC power Cord, 250 V, 10 A

(India)

AC power cord, 250 V, 10 A, MP232 plug

(Switzerland)

AC power Cord, 250 V, 10 A

(Brazil)

AC power cord, 250 V, 10 A (13 A fuse), BS1363 plug

(United Kingdom)

Power Cord Specifications

2.58.2CAB-250V-10A-ID

2.58.2CAB-9K10A-SW

2.58.2CAB-250V-10A-BR

2.58.2CAB-9K10A-UK

AC power cord, 125 V, 13 A, NEMA 5-15 plug

(North America)

AC power cord, NEMA L6-20 to C13 connectors

AC power cord, 250 V, 10 A, CEI 23-16/VII plug

(Italy)

No power cord

2.58.2CAB-9K12A-NA

2.06.6CAB-AC-L620-C13

2.58.2CAB-9K10A-IT

NANAR2XX-DMYMPWRCORD

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

33

Power Cord Specifications

Server Specifications

Cisco Secure Network Server 3600 Series Appliance Hardware Installation Guide

34