Page 1
Regulatory Compliance and Safety Information
for the Cisco Global Site Selector 4492R
This document contains regulatory compliance and safety information for the Cisco Global Site Selector
4492R, product number GSS-4492R-K9. Read this document before installing or servicing the product.
Note Only trained and qualified service personnel (as defined in IEC 60950-1 and AS/NZS 60950) should
install, replace, or service the equipment. Install the system in accordance with the U.S. National Electric
Code if you are in the United States.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
This document includes the following sections:
• Translated Safety Warnings, page 2
• European Directives, page 36
• California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations,
Chapter 33), page 37
• Standards Compliance, page 37
• EMC Environmental Conditions for Products Installed in the European Union, page 38
• EMC Class A Notices and Warnings, page 38
• Japanese Electric Appliance Laws, page 41
• Related Documentation, page 42
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2006 Cisco Systems, Inc. All rights reserved.
Page 2
Translated Safety Warnings
• Obtaining Documentation, page 42
• Documentation Feedback, page 43
• Cisco Product Security Overview, page 43
• Product Alerts and Field Notices, page 44
• Obtaining Technical Assistance, page 45
• Obtaining Additional Publications and Information, page 46
Translated Safety Warnings
This section includes translations in multiple languages of the following warnings that may appear in
your product documents:
• Statement 1—Power Disconnection Warning, page 3
• Statement 12—Power Supply Disconnection Warning, page 4
• Statement 106—More Than One Power Cord, page 5
• Statement 117—Safety Cover Requirement, page 6
• Statement 207—Power Supply Circuitry Warning, page 7
• Statement 1001—Work During Lightning Activity, page 8
• Statement 1004—Installation Instructions, page 9
• Statement 1006—Chassis Warning for Rack-Mounting and Servicing, page 11
• Statement 1015—Battery Handling, page 16
• Statement 1017—Restricted Area, page 18
• Statement 1021—SELV Circuit, page 20
• Statement 1024—Ground Conductor, page 22
• Statement 1029—Blank Faceplates and Cover Panels, page 24
• Statement 1030—Equipment Installation, page 27
• Statement 1040—Product Disposal, page 29
• Statement 1041—Disconnecting Telephone-Network Cables, page 31
• Statement 1045—Short-Circuit Protection, page 32
• Statement 1064—Grounded Equipment, page 34
• Statement 1074—Comply with Local and National Electrical Codes, page 35
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
2
78-17975-01
Page 3
Statement 1—Power Disconnection Warning
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT
te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Ennen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja
kytke virtajohto irti.
Avant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt
(OFF) et débrancher le cordon d'alimentation.
Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen
das Netzkabel aus der Steckdose.
Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare
il cavo dell’alimentazione.
Slå AV strømmen og trekk ut strømledningen før det utføres arbeid på et system som er utstyrt med
en av/på-bryter.
Antes de começar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente
eléctrica e retire o cabo de alimentação da tomada.
Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF),
cortar la alimentación y desenchufar el cable de alimentación.
78-17975-01
Varning!
Slå AV strömmen och dra ur nätsladden innan du utför arbete på ett system med strömbrytare.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
3
Page 4
Translated Safety Warnings
Statement 12—Power Supply Disconnection Warning
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Before working on a chassis or working near power supplies, unplug the power cord on AC units;
disconnect the power at the circuit breaker on DC units.
Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen
de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom toestellen dient u de
stroom uit te schakelen bij de stroomverbreker.
Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta suojakytkimellä, ennen
kuin teet mitään asennuspohjalle tai työskentelet virtalähteiden läheisyydessä.
Avant de travailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le
cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unités en courant
continu au niveau du disjoncteur.
Bevor Sie an einem Chassis oder in der Nähe von Netzgeräten arbeiten, ziehen Sie bei
Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den Strom am
Unterbrecher ab.
Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle
unità CA; scollegare l'alimentazione all’interruttore automatico sulle unità CC.
Før det utføres arbeid på kabinettet eller det arbeides i nærheten av strømforsyningsenheter, skal
strømledningen trekkes ut på vekselstrømsenheter og strømmen kobles fra ved strømbryteren på
likestrømsenheter.
Aviso
¡Advertencia!
Varning!
Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de
energia, desligue o cabo de alimentação nas unidades de corrente alternada; desligue a corrente
no disjuntor nas unidades de corrente contínua.
Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentación,
desenchufar el cable de alimentación en los equipos de corriente alterna (CA); cortar la
alimentación desde el interruptor automático en los equipos de corriente continua (CC).
I
nnan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter
dra ur nätsladden och för likströmsenheter bryta strömmen vid överspänningsskyddet.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
4
78-17975-01
Page 5
Statement 106—More Than One Power Cord
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
This unit might have more than one power cord. To reduce the risk of electrical shock, disconnect
all power supply cords before servicing the unit.
Deze eenheid kan meer dan één elelektriciteitssnoer hebben. Om het risiko op een elektrische
schok te reduceren, dient u alle elektriciteitssnoeren te ontkoppelen voordat u onderhoud op de
eenheid uitvoert.
Tässä laitteessa voi olla useampia virtajohtoja. Sähköiskun välttämiseksi on kaikki sähköjohdot
irrotettava ennen laitteen huoltoa.
Cette unité doit être équipée de plusieurs cordons d'alimentation. Pour réduire le risque de choc
électrique, débranchez tous les cordons d’alimentation avant toute opération de maintenance.
Diese Einheit könnte mehr als ein Stromkabel haben. Um das Risiko eines elektrischen Schlags zu
reduzieren, trennen Sie vor Bedienung der Einheit alle Stromkabel ab.
Questa unità può avere più di un cavo elettrico. Per ridurre il rischio di ricevere una scossa
elettrica, staccate tutti i cavi elettrici prima di fare alcuna manutenzione nell'unità.
Denne enheten kan være utstyrt med mer enn én strømledning. Forhindre fare for elektrisk støt ved
å trekke ut alle strømstøpsler før det utføres service eller reparasjoner på enheten.
Este dispositivo pode possuir mais do que um cabo de alimentação de energia. Para reduzir o risco
de choque eléctrico, desconecte todos os cabos de alimentação de energia eléctrica antes de
reparar o dispositivo.
¡Advertencia!
78-17975-01
Varning!
Esta unidad puede tener más de un cable de suministro eléctrico. Para reducir el riesgo de
electrocución, desconecte todos los cables de suministro eléctrico antes de reparar la unidad.
Denna enhet är eventuellt försedd med mer än en nätsladd. Förhindra risken av elektrisk stöt genom
att koppla ur alla strömförsörjningssladdar innan du utför service eller reparationer på enheten.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
5
Page 6
Translated Safety Warnings
Statement 117—Safety Cover Requirement
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
The safety cover is an integral part of the product. Do not operate the unit without the safety cover
installed. Operating the unit without the cover in place will invalidate the safety approvals and pose
a risk of fire and electrical hazards.
Het beveiligingsdeksel is een integraal onderdeel van het product. Deze eenheid niet bedienen als
het beveiligingsdeksel niet geïnstalleerd is. Als het deksel niet op zijn plaats is tijdens de
bediening, zal dit de veiligheidsaanbevelingen ongeldig maken en een risico op brand en
elektrische gevaren vormen.
Suojakansi on tärkeä osa tuotetta. Yksikköä ei saa käyttää ilman suojakantta. Yksikön käyttö ilman
suojakantta mitätöi turvallisuushyväksynnät ja aiheuttaa tulipalon ja sähköiskun vaaran.
Le plateau de sécurité est une partie intégrante du produit. Pour éviter tout risque de feu ou
d'accident électrique, n'utilisez jamais l'unité lorsque ce plateau n'est pas installé. Les garanties
de sécurité seraient annulées.
Die Sicherheitsabdeckung ist integraler Bestandteil des Produkts. Die Einheit darf nicht ohne
installierte Sicherheitsabdeckung betrieben werden. Ein Betreiben der Einheit ohne korrekt
installierte Abdeckung verstößt gegen die Sicherheitsnormen und führt zu Brandgefahr sowie
elektrischen Sicherheitsrisiken.
Attenzione: Il pannello di sicurezza è parte integrante del prodotto. Non fate funzionare il sistema
senza il pannello di sicurezza. Far funzionare il sistema senza il pannello invaliderà le certificazioni
di sicurezza e può'dare luogo a rischi di incendio e a cortocircuiti.
Advarsel
Aviso
¡Advertencia!
Varning!
Dette sikkerhetsdekselet er en integral del av produktet. Enheten skal ikke brukes uten at
sikkerhetsdekselet er montert. Bruk av enheten uten at sikkerhetsdekselet sitter på plass, vil
ugyldiggjøre sikkerhetsgodkjenningene, og kan dessuten utgjøre fare for brann og faremomenter i
forbindelse med elektrisitet.
A cobertura de segurança é uma parte integral do produto. Não opere a unidade sem a respectiva
cobertura de segurança instalada. Operar a unidade sem esta cobertura anulará as aprovações de
segurança e constituirá um risco de incêndio e perigo eléctrico.
La cubierta de seguridad forma parte integral del producto. No haga funcionar este producto sin la
cubierta de seguridad instalada, de lo contrario se invalidarían las aprobaciones de seguridad y se
correría el riesgo de incendio o de descargas eléctricas.
Skyddshuven är en väsentlig del av produkten. Använd inte enheten utan installerad skyddshuv. Om
enheten används utan skyddshuven på plats upphävs alla säkerhetsgodkännanden och risk för
brandfara och elektrisk fara föreligger.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
6
78-17975-01
Page 7
Statement 207—Power Supply Circuitry Warning
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
The power supply circuitry for the equipment can constitute an energy hazard. Before you install or
replace the equipment, remove all jewelry (including rings, necklaces, and watches). Metal objects
can come into contact with exposed power supply wiring or circuitry inside the DSLAM equipment.
This could cause the metal objects to heat up and cause serious burns or weld the metal object to
the equipment.
De elektrische schakelingen voor de apparatuur kunnen gevaar opleveren. Voordat u de apparatuur
installeert of verwijdert, moet u alle sieraden (ringen, kettingen en horloges) afdoen. Metalen
voorwerpen kunnen in contact komen met blootliggende elektrische bedrading of schakelingen in
de DSLAM-apparatuur. Hierdoor kunnen de metalen voorwerpen warm worden en ernstige
brandwonden veroorzaken of kan het metalen voorwerp versmelten met de apparatuur.
Laitteiston virtapiiri saattaa aiheuttaa sähköiskun vaaran. Ennen kuin asennat tai korvaat
laitteiston, riisu korut (sormukset, kaulakorut ja rannekellot). Metalliesineet voivat joutua
kosketuksiin suojaamattomien virtajohtojen tai -piirien kanssa DSLAM-laitteiston sisällä.
Metalliesineet saattavat kuumeta ja aiheuttaa vakavia palovammoja tai hitsata metalliesineet
kiinni laitteistoon.
Le circuit d'alimentation de l'équipement présente un danger d'électrocution. Avant d'installer ou
de remplacer l'équipement, enlevez tous vos bijoux (bagues, colliers et montres). Les objets en
métal peuvent entrer en contact avec les câbles ou les circuits d’alimentation exposés de
l'équipement DSLAM. Cela peut provoquer le réchauffement des objets en métal et être à l'origine
de brûlures graves ou bien souder l'objet en métal à l'équipement.
Die Stromzuführungen für das Gerät können eine Gefahr darstellen. Legen Sie vor dem Installieren
oder Entfernen des Geräts jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) ab.
Metallobjekte können in Kontakt mit freiliegenden Stromzuführungen oder Schaltkreisen innerhalb
des DSLAM-Geräts kommen. Dies kann zur Erhitzung dieser Objekte führen und schwere
Verbrennungen oder das Verschmelzen des Metallobjekts mit dem Gerät verursachen.
Avvertenza
78-17975-01
Advarsel
Aviso
I circuiti di alimentazione di questa apparecchiatura possono comportare un rischio elettrico. Prima
di installare o sostituire l’apparecchiatura, rimuovere tutta gli oggetti metallici indossati (inclusi
anelli, collane e orologi). Gli oggetti metallici potrebbero venire a contatto con i fili di alimentazione
o i circuiti privi di protezione all’interno dell’apparecchiatura DSLAM (Advanced Digital Subscriber
Line Access Multiplexers). Ciò potrebbe causare il surriscaldamento degli oggetti metallici e
causare la bruciatura o la fusione degli oggetti metallici stessi o dell’apparecchiatura.
Strømforsyningskretsen for utstyret kan gi elektrisk støt. Før du installerer eller skifter ut utstyret,
bør du ta av deg alle smykker (ringer, halsbånd og klokke). Metallobjekter kan komme i kontakt med
åpne ledninger eller kretser i DSLAM-utstyret. Dette kan føre til at metallobjektene varmes opp og
forårsaker alvorlige brannskader eller at metallobjektene smeltes sammen med utstyret.
Os circuitos de fornecimento de energia para o equipamento podem constituir perigo. Antes de
instalar ou substituir o equipamento, tire todas as jóias (incluindo anéis, colares, e relógios). Os
objectos metálicos podem entrar em contacto com os cabos ou circuitos de fornecimento de energia
expostos dentro do equipamento DSLAM.O contacto assim estabelecido pode originar o
aquecimento dos objectos metálicos e causar queimaduras graves ou soldar o objecto metálico ao
equipamento.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
7
Page 8
Translated Safety Warnings
¡Advertencia!
Varning!
El sistema de circuitos de alimentación del equipo puede ser peligroso. Antes de instalar o sustituir
el equipo, quítese todas las joyas (incluyendo anillos, collares y relojes), ya que los objetos
metálicos podrían ponerse en contacto con cables de alimentación expuestos o con el sistema de
circuitos existente dentro del DSLAM. Si esto fuera así, podría ocurrir que los objetos de metal se
calentaran y le causaran serias quemaduras o incluso que el objeto metálico se soldara al equipo.
Nätanslutningens strömkretsanordning för utrustningen kan utgöra energifara. Avlägsna därför alla
smycken (inklusive ringar, halsband och armbandsur) innan du installerar eller byter ut utrustning.
Metallobjekt kan komma i kontakt med oskyddade nätanslutningskablar eller
strömkretsanordningar inuti DSLAM-utrustningen. Detta kan medföra att metallobjekten hettar upp
vilket i sin tur kan medföra allvarliga brännskador eller att metallobjektet svetsas fast på
utrustningen.
Statement 1001—Work During Lightning Activity
Warning
Waarschuwing
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan
te sluiten of te ontkoppelen.
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.
Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.
Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn
es gewittert.
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.
Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).
No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas
eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
8
78-17975-01
Page 9
Translated Safety Warnings
Statement 1004—Installation Instructions
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Read the installation instructions before connecting the system to the power source.
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
9
Page 10
Translated Safety Warnings
Varning!
Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
10
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 11
Translated Safety Warnings
Statement 1006—Chassis Warning for Rack-Mounting and Servicing
Warning
Waarschuwing
Varoitus
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to
ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in
the rack.
Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een
servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel
stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren:
• Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is.
• Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van onderen naar boven te laden
met het zwaarste onderdeel onderaan in het rek.
• Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te monteren voordat u het
toestel in het rek monteert of het daar een servicebeurt geeft.
Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä, on noudatettava erityisiä
varotoimia järjestelmän vakavuuden säilyttämiseksi, jotta vältytään loukkaantumiselta. Noudata
seuraavia turvallisuusohjeita:
• Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
• Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen sen alaosasta kaikkein raskaimmalla
esineellä ja siirry sitten sen yläosaan.
• Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen tai sen huoltamista siinä.
78-17975-01
Attention
Pour éviter toute blessure corporelle pendant les opérations de montage ou de réparation de cette
unité en casier, il convient de prendre des précautions spéciales afin de maintenir la stabilité du
système. Les directives ci-dessous sont destinées à assurer la protection du personnelþ:
• Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le bas.
• Si cette unité est montée dans un casier partiellement rempli, charger le casier de bas en haut en plaçant
l'élément le plus lourd dans le bas.
• Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs avant de monter ou de réparer
l'unité en casier.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
11
Page 12
Translated Safety Warnings
Warnung
Avvertenza
Advarsel
Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell
müssen Sie besondere Vorkehrungen treffen, um sicherzustellen, daß das System stabil bleibt. Die
folgenden Richtlinien sollen zur Gewährleistung Ihrer Sicherheit dienen:
• Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht werden.
• Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das Gestell von unten nach oben zu laden,
wobei das schwerste Bauteil unten im Gestell anzubringen ist.
• Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die Stabilisatoren zu installieren, bevor Sie
die Einheit im Gestell anbringen oder sie warten.
Per evitare infortuni fisici durante il montaggio o la manutenzione di questa unità in un supporto,
occorre osservare speciali precauzioni per garantire che il sistema rimanga stabile. Le seguenti
direttive vengono fornite per garantire la sicurezza personale:
• Questa unità deve venire montata sul fondo del supporto, se si tratta dell’unica unità da montare nel supporto.
• Quando questa unità viene montata in un supporto parzialmente pieno, caricare il supporto dal basso all’alto,
con il componente più pesante sistemato sul fondo del supporto.
• Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi prima di montare o di procedere alla
manutenzione dell’unità nel supporto.
Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner
seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne
om sikkerheten:
• Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste enheten i kabinettet.
• Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes fra bunnen og opp med
den tyngste komponenten nederst i kabinettet.
• Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres før montering eller utføring
av reparasjonsarbeid på enheten i kabinettet.
Aviso
¡Advertencia!
Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante, deverá
tomar precauções especiais para se certificar de que o sistema possui um suporte estável. As
seguintes directrizes ajudá-lo-ão a efectuar o seu trabalho com segurança:
• Esta unidade deverá ser montada na parte inferior da estante, caso seja esta a única unidade a ser montada.
• Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais pesados na parte inferior
da estante, arrumando-os de baixo para cima.
• Se a estante possuir um dispositivo de estabilização, instale-o antes de montar ou reparar a unidade.
Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente durante
su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable. Para
garantizar su seguridad, proceda según las siguientes instrucciones:
• Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad en el mismo.
• Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar la instalación desde la
parte inferior hacia la superior colocando el equipo más pesado en la parte inferior.
• Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes de montar o proceder al
mantenimiento del equipo instalado en el bastidor.
12
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 13
Translated Safety Warnings
Varning!
För att undvika kroppsskada när du installerar eller utför underhållsarbete på denna enhet på en
ställning måste du vidta särskilda försiktighetsåtgärder för att försäkra dig om att systemet står
stadigt. Följande riktlinjer ges för att trygga din säkerhet:
• Om denna enhet är den enda enheten på ställningen skall den installeras längst ned på ställningen.
• Om denna enhet installeras på en delvis fylld ställning skall ställningen fyllas nedifrån och upp, med de tyngsta
enheterna längst ned på ställningen.
• Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast innan enheten installeras eller
underhålls på ställningen.
•
•
•
•
•
•
•
•
•
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
13
Page 14
Translated Safety Warnings
Aviso
Advarsel
Para evitar lesões corporais ao montar ou dar manutenção a esta unidade em um rack, é necessário
tomar todas as precauções para garantir a estabilidade do sistema. As seguintes orientações são
fornecidas para garantir a sua segurança:
• Se esta for a única unidade, ela deverá ser montada na parte inferior do rack.
• Ao montar esta unidade em um rack parcialmente preenchido, carregue-o de baixo para cima com o
componente mais pesado em sua parte inferior.
• Se o rack contiver dispositivos estabilizadores, instale-os antes de montar ou dar manutenção à unidade
existente.
For at forhindre legemesbeskadigelse ved montering eller service af denne enhed i et rack, skal du
sikre at systemet står stabilt. Følgende retningslinjer er også for din sikkerheds skyld:
• Enheden skal monteres i bunden af dit rack, hvis det er den eneste enhed i racket.
• Ved montering af denne enhed i et delvist fyldt rack, skal enhederne installeres fra bunden og opad med den
tungeste enhed nederst.
• Hvis racket leveres med stabiliseringsenheder, skal disse installeres for enheden monteres eller serviceres i
racket.
14
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 15
Translated Safety Warnings
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
15
Page 16
Translated Safety Warnings
Statement 1015—Battery Handling
Warning
Waarschuwing
Varoitus
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
16
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met
hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen
overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen ainoastaan samantai vastaavantyyppistä akkua, joka on valmistajan suosittelema. Hävitä käytetyt akut valmistajan
ohjeiden mukaan.
78-17975-01
Page 17
Translated Safety Warnings
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile
de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées
conformément aux instructions du fabricant.
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch
den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien
nach den Anweisungen des Herstellers.
Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo
uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni
del produttore.
Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller
tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens
instruksjoner.
Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma
bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas
conforme as instruções do fabricante.
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería
exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las
baterías gastadas según las instrucciones del fabricante.
Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma batterityp som
rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens anvisningar vid kassering av
använda batterier.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
17
Page 18
Translated Safety Warnings
Statement 1017—Restricted Area
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Deze eenheid is bestemd voor installatie in plaatsen met beperkte toegang. Toegang tot een
dergelijke plaats kan alleen verkregen worden door middel van een speciaal instrument, een slot
en sleutel of een ander veiligheidsmiddel.
Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on rajoitettua. Tällaiseen paikkaan
pääsee vain erikoistyökalua, lukkoon sopivaa avainta tai jotakin muuta turvalaitetta käyttämällä.
Cet appareil est à installer dans des zones d'accès réservé. L'accès à une zone d'accès réservé n'est
possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout autre
moyen de sécurité.
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt zu
derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer
sonstigen Sicherheitsvorkehrung möglich.
Questa unità è prevista per essere installata in un'area ad accesso limitato, vale a dire un'area
accessibile solo mediante l'uso di un attrezzo speciale, come lucchetto e chiave, o altri dispositivi
di sicurezza.
Denne enheten er beregnet på installasjon i områder med begrenset tilgang. Et begrenset
tilgangsområde kan bare nås ved hjelp av et spesielt verktøy, lås og nøkkel, eller andre
sikkerhetsanordninger.
¡Advertencia!
Varning!
18
Aviso
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
Esta unidade foi concebida para instalação em áreas de acesso restrito. Uma área de acesso restrito
é uma área à qual apenas tem acesso o pessoal de serviço autorizado, que possua uma ferramenta,
chave e fechadura especial, ou qualquer outra forma de segurança.
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo puede obtenerse
acceso a una de estas áreas mediante la utilización de una herramienta especial, cerradura con
llave u otro medio de seguridad.
Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett område med begränsat
tillträde kan endast tillträdas med hjälp av specialverktyg, lås och nyckel eller annan
säkerhetsanordning.
78-17975-01
Page 19
Translated Safety Warnings
Aviso
Advarsel
Esta unidade deve ser instalada em áreas de acesso restrito. Uma área de acesso restrito só pode
ser acessada com o uso de uma ferramenta especial, cadeado e chave ou outros meios de
segurança.
Denne enhed er beregnet til installation i områder med begrænset adgang. Der kan kun opnås
adgang til et begrænset område ved at bruge et særligt stykke værktøj, lås og nøgle, eller en anden
form for sikkerhed.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
19
Page 20
Translated Safety Warnings
Statement 1021—SELV Circuit
Warning
Waarschuwing
Varoitus
Attention
Warnung
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to
telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain
TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when
connecting cables.
Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning
(genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits
verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal
netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45
connectors. Ga voorzichtig te werk wanneer u kabels verbindt.
Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä
(TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit
puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää
RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.
Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety
Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network
Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau
longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des
connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise)
nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten
SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch
RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.
20
Avvertenza
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai
circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN
contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione
quando si collegano cavi.
78-17975-01
Page 21
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår
elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det
finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du
kobler kabler.
Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos
circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN
contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado
ao conectar os cabos.
Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety
extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage =
TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los
puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos
casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al
conectar los cables.
För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning
(SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller
SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med
RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
21
Page 22
Translated Safety Warnings
Statement 1024—Ground Conductor
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in
the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld
en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde
aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische
inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding
gezorgd is.
Laitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein
asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet
epävarma maadoituksen sopivuudesta.
Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni
utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la
mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité
électrique ou à un électricien.
Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das
Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher
sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige
Inspektionsbehörde oder einen Elektriker.
Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di
protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo
corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a terra,
richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un elettricista.
Advarsel
¡Advertencia!
Varning!
22
Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert
jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er
usikker på om det finnes velegnet jordning.
Aviso
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um
aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de aterramento
disponível, entre em contato com os serviços locais de inspeção elétrica ou um eletricista
qualificado.
Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el
equipo si no hay un conductor de tierra instalado correctamente. Póngase en contacto con la
autoridad correspondiente de inspección eléctrica o con un electricista si no está seguro de que
haya una conexión a tierra adecuada.
Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen
utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig
jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.
78-17975-01
Page 23
Translated Safety Warnings
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
23
Page 24
Translated Safety Warnings
Statement 1029—Blank Faceplates and Cover Panels
Warning
Waarschuwing
Varoitus
Attention
Warnung
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference
(EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis.
Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Lege vlakplaten en afdekpanelen vervullen drie belangrijke functies: ze voorkomen blootstelling
aan gevaarlijke voltages en stroom binnenin het frame, ze bevatten elektromagnetische storing
(EMI) hetgeen andere apparaten kan verstoren en ze leiden de stroom van koellucht door het frame.
Het systeem niet bedienen tenzij alle kaarten, vlakplaten en afdekkingen aan de voor- en achterkant
zich op hun plaats bevinden.
Tyhjillä tasolaikoilla ja suojapaneeleilla on kolme tärkeää käyttötarkoitusta: Ne suojaavat
asennuspohjan sisäisille vaarallisille jännitteille ja sähkövirralle altistumiselta; ne pitävät
sisällään elektromagneettisen häiriön (EMI), joka voi häiritä muita laitteita; ja ne suuntaavat
tuuletusilman asennuspohjan läpi. Järjestelmää ei saa käyttää, elleivät kaikki tasolaikat, etukannet
ja takakannet ole kunnolla paikoillaan.
Ne jamais faire fonctionner le système sans que l’intégralité des cartes, des plaques métalliques et
des panneaux avant et arrière ne soient fixés à leur emplacement. Ceux-ci remplissent trois
fonctions essentielles : ils évitent tout risque de contact avec des tensions et des courants
dangereux à l’intérieur du châssis, ils évitent toute diffusion d’interférences électromagnétiques
qui pourraient perturber le fonctionnement des autres équipements, et ils canalisent le flux d’air de
refroidissement dans le châssis.
Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen: (1) Sie schützen vor
gefährlichen Spannungen und Strom innerhalb des Chassis; (2) sie halten elektromagnetische
Interferenzen (EMI) zurück, die andere Geräte stören könnten; (3) sie lenken den kühlenden
Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates,
Voder- und Rückabdeckungen an Ort und Stelle sind.
24
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 25
Translated Safety Warnings
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Le piattaforme bianche e i panelli di protezione hanno tre funzioni importanti: Evitano l'esposizione
a voltaggi e correnti elettriche pericolose nello chassis, trattengono le interferenze
elettromagnetiche (EMI) che potrebbero scombussolare altri apparati e dirigono il flusso di aria per
il raffreddamento attraverso lo chassis. Non mettete in funzione il sistema se le schede, le
piattaforme, i panelli frontali e posteriori non sono in posizione.
Blanke ytterplater og deksler sørger for tre viktige funksjoner: de forhindrer utsettelse for farlig
spenning og strøm inni kabinettet; de inneholder elektromagnetisk forstyrrelse (EMI) som kan
avbryte annet utstyr, og de dirigerer luftavkjølingsstrømmen gjennom kabinettet. Betjen ikke
systemet med mindre alle kort, ytterplater, frontdeksler og bakdeksler sitter på plass.
As faces furadas e os painéis de protecção desempenham três importantes funções: previnem
contra uma exposição perigosa a voltagens e correntes existentes no interior do chassis; previnem
contra interferência electromagnética (EMI) que poderá danificar outro equipamento; e canalizam
o fluxo do ar de refrigeração através do chassis. Não deverá operar o sistema sem que todas as
placas, faces, protecções anteriores e posteriores estejam nos seus lugares.
Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la
exposición a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia
electromagnética (EMI) que podría perturbar la operación de otros equipos y dirigen el flujo de aire
de enfriamiento a través del chasis. No haga funcionar el sistema a menos que todas las tarjetas,
placas frontales, cubiertas frontales y cubiertas traseras estén en su lugar.
Tomma framplattor och skyddspaneler har tre viktiga funktioner: de förhindrar att personer utsätts
för farlig spänning och ström som finns inuti chassit; de innehåller elektromagnetisk interferens
(EMI) som kan störa annan utrustning; och de styr riktningen på kylluftsflödet genom chassit. Använd
inte systemet om inte alla kort, framplattor, fram- och bakskydd är på plats.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
25
Page 26
Translated Safety Warnings
Aviso
Advarsel
Plaquetas vazias e painéis de proteção têm três funções importantes: impedem a exposição a
tensões e correntes elétricas perigosas dentro do chassi; apresentam interferência
eletromagnética (EMI) que pode danificar outros equipamentos: direcionam o fluxo do ar
refrigerado pelo chassi. Não opere o sistema a menos que todas as placas, plaquetas, tampas
frontais e tampas traseiras estejam em seu devido lugar.
Blanke frontplader og sidepaneler tjener tre vigtige formål: de forhinder udsættelse for farlig
spænding og strøm inde i chassiset, de isolerer elektromagnetisk interferens (EMI), der kan forstyre
andet udstyr, og de leder en strøm af kølig luft gennem chassiset. Betjen ikke systemet medmindre
alle kort, frontplader, sidepaneler og bagpaneler er på plads.
26
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 27
Translated Safety Warnings
Statement 1030—Equipment Installation
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd
geschoold personeel.
Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen
tunteva henkilökunta.
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces
équipements à des personnels qualifiés et expérimentés.
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem
Personal gestattet werden.
Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale
competente.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
27
Page 28
Translated Safety Warnings
Advarsel
Aviso
¡Advertencia!
Varning!
Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på
dette utstyret.
Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão
deste equipamento.
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera
denna utrustning.
Aviso
Advarsel
Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar
manutenção a este equipamento.
Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.
28
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 29
Statement 1040—Product Disposal
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Ultimate disposal of this product should be handled according to all national laws and regulations.
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives
de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og
bestemmelser.
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
29
Page 30
Translated Safety Warnings
Aviso
Advarsel
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações
nacionais.
Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
30
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 31
Statement 1041—Disconnecting Telephone-Network Cables
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages.
Voordat u de eenheid opent, dient u de verbinding met het telefoonnetwerk te verbreken door de
kabels te ontkoppelen om zo contact met telefoonnetwerk-spanning te vermijden.
Vältä joutumista kosketuksiin puhelinverkkojännitteiden kanssa irrottamalla puhelinverkoston
kaapelit ennen yksikön aukaisemista.
Pour éviter tout risque de choc électrique (tensions présentes dans l'unité), débranchez les câbles
du réseau téléphonique AVANT d'ouvrir l'unité.
Bevor Sie das Gerät öffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um Kontakt mit
Telefonnetzspannungen zu vermeiden.
Prima di aprire l'unità, scollegare i cavi della rete telefonica per evitare di entrare in contatto con
la tensione di rete.
Før enheten åpnes, skal kablene for telenettet kobles fra for å unngå å komme i kontakt med
spenningen i telenettet.
Antes de abrir a unidade, desligue os cabos da rede telefónica para evitar contacto com a tensão da
respectiva rede.
¡Advertencia!
Varning!
Antes de abrir la unidad, desconectar el cableado dirigido a la red telefónica para evitar contacto
con voltajes de la propia red.
Koppla loss ledningarna till telefonnätet innan du öppnar enheten så att kontakten med
telefonnätsspänningen bryts.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
31
Page 32
Translated Safety Warnings
Statement 1045—Short-Circuit Protection
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Voor dit product moet kortsluitbeveiliging (overstroombeveiliging) deel uitmaken van de installatie
in het gebouw. De installatie moet voldoen aan de nationale en lokale bedradingvoorschriften.
Tämä tuote vaatii suojauksen oikosulkuja (ylivirtaa) vastaan osana asennusta rakennukseen.
Asenna ainoastaan kansallisten ja paikallisten johdotussäännösten mukaisesti.
La protection de ce produit contre les courts-circuits (surtensions) doit être assurée par la
configuration électrique du bâtiment. Vérifiez que l'installation a lieu uniquement en conformité
avec les normes de câblage en vigueur au niveau national et local.
Für dieses Produkt ist eine Kurzschlußsicherung (Überstromsicherung) erforderlich, die als Teil der
Gebäudeinstallation zur Verfügung gestellt wird. Die Installation sollte nur in Übereinstimmung mit
den nationalen und regionalen Vorschriften zur Verkabelung erfolgen.
Questo prodotto richiede una protezione contro i cortocircuiti, da fornirsi come parte integrante
delle dotazioni presenti nell’edificio. Effettuare l’installazione rispettando le Norme CEI pertinenti.
Dette produktet krever beskyttelse mot kortslutninger (overspenninger) som en del av
installasjonen. Bare installer utstyret i henhold til nasjonale og lokale krav til ledningsnett.
Este produto requer proteção contra curto-circuitos (sobreintensidade de corrente), que deve estar
instalada nos edifícios. Instale apenas de acordo com as normas de instalação elétrica nacionais
e locais.
Advertencia
32
Este producto necesita estar conectado a la protección frente a cortacircuitos (sobretensiones) que
exista en el edificio. Instálelo únicamente en conformidad con las regulaciones sobre cableado,
tanto locales como nacionales, a las que se tenga que atener.
Varning!
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
Denna produkt kräver att kortslutningsskydd (överström) tillhandahålles som en del av
byggnadsinstallationen. Installera bara i enlighet med nationella och lokala
kabeldragningsbestämmelser.
78-17975-01
Page 33
Translated Safety Warnings
Aviso
Advarsel
Este produto requer uma proteção contra curto-circuito (sobrecorrente) que deve fazer parte da
instalação do edifício. Faça a instalação somente de acordo com as regulamentações de
cabeamento nacionais e locais.
Dette produkt kræver beskyttelse mod kortslutning (overstrøm). Dette skal være en del
elinstallationen i bygningen. Installation skal ske i overensstemmelse med nationale og lokale
ledningsregler.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
33
Page 34
Translated Safety Warnings
Statement 1064—Grounded Equipment
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
This equipment is intended to be grounded to comply with emission and immunity requirements.
Ensure that the switch functional ground lug is connected to earth ground during normal use.
Deze apparatuur dient geaard te worden in overeenstemming met emissie- en immuniteitsvereisten.
Zorg dat de functionele verbindingsslip van de schakelaar geaard is tijdens normaal gebruik.
Tämä laite on tarkoitettu maadoitettavaksi säteily- ja häiriönsietovaatimusten täyttämiseksi.
Varmista, että kytkimen toiminnallinen maadoituskenkä on kytketty maadoitukseen normaalikäytön
aikana.
Cet équipement doit être relié à la terre pour répondre aux exigences en matière d'émissions et
d'immunité. Vérifiez que la vis de mise à la terre fonctionnelle du commutateur est bien connectée
à la terre pendant l'exploitation de l'équipement.
Dieses Gerät muss geerdet werden, um den Strahlungs- und Störfestigkeitsbestimmungen zu
entsprechen. Stellen Sie daher sicher, dass während des normalen Betriebs die
Massenanschlussöse des Switches mit dem Erdleiter verbunden ist.
Quest'apparecchiatura deve essere collegata a terra al fine di essere conforme ai requisiti di
emissione e immunità. Assicurarsi che il terminale di terra funzionale dello switch sia collegato a
massa durante l'uso normale.
Dette utstyret er beregnet på jording som samsvarer med kravene til utslipp og immunitet. Påse at
bryterens funksjonelle jordingskabelsko er koblet til jording ved normal bruk.
Aviso
¡Advertencia!
Varning!
Este equipamento deve ser aterrado para atender aos requisitos de emissão e imunidade.
Certifique-se de que o suporte de aterramento funcional do switch esteja conectado ao terra
durante a operação normal.
Este equipo está diseñado para que se conecte a tierra de modo que cumpla con los requisitos de
emisión e inmunidad. Asegúrese de que el terminal de tierra funcional del switch está conectado a
tierra durante el uso normal.
Denna utrustning bör jordas för att uppfylla gällande emissions- och immunitetskrav. Se till att
omkopplarens funktionella jordningsfläns är jordad under normal användning.
34
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 35
Translated Safety Warnings
Statement 1074—Comply with Local and National Electrical Codes
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Installation of the equipment must comply with local and national electrical codes.
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti.
L'équipement doit être installé conformément aux normes électriques nationales et locales.
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.
Installasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.
A instalação do equipamento tem de estar em conformidade com os códigos eléctricos locais e
nacionais.
La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.
Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
35
Page 36
European Directives
European Directives
Statement 275—Declaration of Conformity with Regard to the Directives
73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC
For specifics about which standards have been applied, refer to the Declaration of Conformity.
English:
Dansk:
Deutsch:
Español:
This equipment is in compliance with the essential requirements and other provisions of Directives
73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC.
Dette udstyr er i overensstemmelse med de ufravigelige hensyn og andre bestemmelser i direktiv
73/23/EEC og 89/336/EEC som ændred i direktiv 93/68/EEC.
Dieses Gerät entspricht den wesentlichen Anforderungen und weiteren Bestimmungen der
Richtlinien 73/23/EWG und 89/336/EWG mit der Ergänzung durch Richtlinie 93/68/EWG.
Este equipo cumple con los requisitos esenciales y otras disposiciones de las Directrices 73/23/EEC
y 89/336/EEC de acuerdo a las modificaciones de la Directriz 93/68/EEC.
36
Français:
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
Cet appareil remplit les principales conditions requises et autres dispositions des Directives
73/23/EEC et 89/336/EEC, modifiées par la Directive 93/68/EEC.
78-17975-01
Page 37
California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)
Íslenska:
Italiano:
Nederlands:
Norsk:
Português:
Suomalainen:
Svenska:
Þessir búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipana 73/23/EBE og
89/336/EBE, með breytingum skv. tilskipun 93/68/EBE.
Questa apparecchiatura è conforme ai requisiti essenziali e altre disposizioni delle Direttive
73/23/EEC e 89/336/EEC modificate con la Direttiva 93/68/EEC.
Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijnen
73/23/EEC en 89/336/EEC zoals gewijzigd door richtlijn 93/68/EEC.
Dette utstyret samsvarer med de vesentligste kravene og andre regler i direktivene 73/23/EEC og
89/336/EEC samt i tilleggsdirektiv 93/68/EEC.
Este equipamento satisfaz os requisitos essenciais e outras provisões das Directivas 73/23/EEC e
89/336/EEC, conforme amendados pela Directiva 93/68/EEC.
[Product_Name]
Tämä laite on direktiivien 73/23/ETY ja 89/336/ETY (kuten muutettu direktiivissä 93/68/ETY)
keskeisten vaatimusten ja määräysten mukainen.
Denna utrustning uppfyller de väsentliga kraven och andra villkor i direktiven 73/23/EEC och
89/336/EEC enligt ändringarna i direktiv 93/68/EEC.
California Perchlorate Contamination Prevention Act
(Title 22, California Code of Regulations, Chapter 33)
The battery inside this product might contain perchlorate, a known hazardous substance, so special
handling and disposal of this product might be necessary. For more information about perchlorate
and best management practices for perchlorate-containing substances, see
http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.
Standards Compliance
This section contains the regulatory compliance, safety, and electromagnetic compatibility (EMC)
standards. It also lists the statements applicable to different countries.
Table 1 lists the regulatory standards compliance specifications.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
37
Page 38
EMC Environmental Conditions for Products Installed in the European Union
Table 1 Regulatory Standards Compliance
Item Description
Regulatory compliance Products with the CE Marking indicate compliance with the 89/336/EEC and
73/23/EEC directives, which include the safety and EMC standards listed.
Safety UL 60950
CAN/CSA-C22.2 No. 60950
EN 60950
IEC 60950
AS/NZS 60950
EMC FCC Part 15 (CFR 47) Class A
EN55022 Class A
CISPR 22 Class A
CNS13438 Class A
AS/NZS CISPR22 Class A
VCCI Class A
ICES-003 Class A
CISPR24
EN 55024
EN 61000-3-2
EN 61000-3-3
EMC Environmental Conditions for Products Installed in the
European Union
This section applies to products to be installed in the European Union.
The equipment is intended to operate under the following environmental conditions with respect to
EMC:
• The equipment shall be located in a separate defined area under the user’s control.
• Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.
• AC power distribution shall be one of the following types, where applicable: TN-S and TN-C as
defined in IEC 364-3.
In addition, if equipment is operated in a domestic environment, interference may occur.
EMC Class A Notices and Warnings
This section includes the EMC Class A warnings for the Cisco Global Site Selector 4492R.
Class A Notice for FCC
Modifying the equipment without Cisco’s authorization may result in the equipment no longer
complying with FCC requirements for Class A digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
38
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 39
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case users will be
required to correct the interference at their own expense.
Class A Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Statement 340—Class A Warning for CISPR22
EMC Class A Notices and Warnings
Warning
Waarschuwing
Varoitus
Attention
Warnung
Avvertenza
Advarsel
Aviso
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Dit is een product van klasse A. In een woonomgeving kan dit product radiostoring veroorzaken. In
dat geval moet de gebruiker de juiste maatregelen nemen.
Tämä on A-luokan tuote. Kotona käytettynä tämä tuote voi aiheuttaa radiotaajuushäiriöitä, jolloin
käyttäjän tulisi ryhtyä vaadittaviin toimenpiteisiin häiriöiden ehkäisemiseksi.
Il s'agit d'un produit de classe A. Dans un environnement local, ce produit peut entraîner des
perturbations radioélectriques, auquel cas l'utilisateur devra éventuellement prendre des mesures
adéquates.
Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder
Wohnungsbereich kann es zu Funkstörungen kommen. In diesem Fall muss der Benutzer u. U.
angemessene Maßnahmen ergreifen.
Prodotto di classe A. È possibile che il prodotto generi interferenze radio in un ambienti chiusi. In
questo caso l'utente deve intraprendere le misure adeguate per risolvere il problema.
Dette er et produkt i klasse A. I et hjemmemiljø kan dette produktet forårsake radioforstyrrelser, og
brukeren kan da være nødt til å ta de nødvendige forholdsregler.
Este é um produto de classe A. Em um ambiente doméstico, este produto pode causar interferência
de rádio. Nesse caso, talvez o usuário precise tomar as medidas adequadas.
¡Advertencia!
78-17975-01
Varning!
Este es un producto de clase A. En el ámbito doméstico, este producto puede causar
radiointerferencias, lo que puede hacer necesaria la puesta en marcha de medidas adecuadas.
Detta är en klass A-produkt. Denna produkt kan orsaka radiostörningar inomhus. Det kan då vara ett
krav att användaren vidtar lämpliga åtgärder.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
39
Page 40
EMC Class A Notices and Warnings
Statement 191—VCCI Class A Warning for Japan
Warning
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
40
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 41
Statement 256—Class A Warning for Hungary
Japanese Electric Appliance Laws
Warning
This equipment is a class A product and should be used and installed properly according to the
Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical
commercial establishments for which special conditions of installation and protection distance are
used.
Statement 257—Class A Notice for Taiwan and Other Traditional Chinese
Markets
Warning
This is a Class A Information Product, when used in residential environment, it may cause radio
frequency interference, under such circumstances, the user may be requested to take appropriate
countermeasures.
Japanese Electric Appliance Laws
Statement 371—Power Cable and AC Adapter
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
41
Page 42
Related Documentation
Related Documentation
For additional information, see the following documents:
Document Title Description
Cisco Global Site Selector
4492R Hardware Installation
Guide
Cisco Global Site Selector
Getting Started Guide
Cisco Global Site Selector
Administration Guide
Cisco Global Site Selector
GUI-Based Global Server
Load-Balancing Configuration
Guide
Cisco Global Site Selector
CLI-Based Global Server
Load-Balancing Configuration
Guide
Cisco Global Site Selector
Command Reference
Describes how to install your Cisco Global Site Selector 4492R
(GSS) and get it ready for operation.
Information on getting your GSS setup, configured, and ready to
perform global server load balancing.
Provides the procedures necessary to properly set up, manage, and
maintain your GSSM and GSS devices, including login security,
software upgrades, GSSM database administration, and logging.
Procedures on how to configure your primary GSSM from the GUI
to perform global server load-balancing, such as configuring source
address lists, domain lists, answers, answer groups, DNS sticky,
network proximity, and DNS rules. This document also provides an
overview of the GSS device and global server load balancing as
performed by the GSS.
Procedures on how to configure your primary GSSM from the CLI
to perform global server load-balancing, such as configuring source
address lists, domain lists, answers, answer groups, DNS sticky,
network proximity, and DNS rules. This document also provides an
overview of the GSS device and global server load balancing as
performed by the GSS.
Provides an alphabetical list, by mode, of all GSS command-line
interface (CLI) commands including syntax, options, and related
commands. This document also describes how to use the CLI
interface.
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. This section explains the
product documentation resources that Cisco offers.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/techsupport
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
42
78-17975-01
Page 43
Product Documentation DVD
The Product Documentation DVD is a library of technical product documentation on a portable medium.
The DVD enables you to access installation, configuration, and command guides for Cisco hardware and
software products. With the DVD, you have access to the HTML documentation and some of the
PDF files found on the Cisco website at this URL:
http://www.cisco.com/univercd/home/home.htm
The Product Documentation DVD is created and released regularly. DVDs are available singly or by
subscription. Registered Cisco.com users can order a Product Documentation DVD (product number
DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at the Product Documentation
Store at this URL:
http://www.cisco.com/go/marketplace/docstore
Ordering Documentation
You must be a registered Cisco.com user to access Cisco Marketplace. Registered users may order
Cisco documentation at the Product Documentation Store at this URL:
Documentation Feedback
http://www.cisco.com/go/marketplace/docstore
If you do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Documentation Feedback
You can provide feedback about Cisco technical documentation on the Cisco Technical Support &
Documentation site area by entering your comments in the feedback form available in every online
document.
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you will find information about how to do the following:
• Report security vulnerabilities in Cisco products
• Obtain assistance with security incidents that involve Cisco products
• Register to receive security information from Cisco
A current list of security advisories, security notices, and security responses for Cisco products is
available at this URL:
78-17975-01
http://www.cisco.com/go/psirt
To see security advisories, security notices, and security responses as they are updated in real time, you
can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS)
feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
43
Page 44
Product Alerts and Field Notices
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them,
and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability
in a Cisco product, contact PSIRT:
• For emergencies only—security-alert@cisco.com
An emergency is either a condition in which a system is under active attack or a condition for which
a severe and urgent security vulnerability should be reported. All other conditions are considered
nonemergencies.
• For nonemergencies —psirt@cisco.com
In an emergency, you can also reach PSIRT by telephone:
• 1 877 228-7302
• 1 408 525-6532
Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to
encrypt any sensitive information that you send to Cisco. P SIRT can wo rk wi th information that has been
encrypted with PGP versions 2.x through 9.x.
Never use a revoked encryption key or an expired encryption key. The correct public key to use in your
correspondence with PSIRT is the one linked in the Contact Summary section of the Security
Vulnerability Policy page at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
The link on this page has the current PGP key ID in use.
If you do not have or use PGP, contact PSIRT to find other means of encrypting the data before sending
any sensitive material.
Product Alerts and Field Notices
Modifications to or updates about Cisco products are announced in Cisco Product Alerts and Cisco Field
Notices. You can receive Cisco Product Alerts and Cisco Field Notices by using the Product Alert Tool
on Cisco.com. This tool enables you to create a profile and choose those products for which you want to
receive information.
To access the Product Alert Tool, you must be a registered Cisco.com user. (To register as a Cisco.com
user, go to this URL: http://tools.cisco.com/RPF/register/register.do) Registered users can access the
tool at this URL: http://tools.cisco.com/Support/PAT/do/ViewMyProfiles.do?local=en
44
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 45
Obtaining Technical Assistance
Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The
Cisco Technical Support & Documentation website on Cisco.com features extensive online support
resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center
(TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact
your reseller.
Cisco Technical Support & Documentation Website
The Cisco Technical Support & Documentation website provides online documents and tools for
troubleshooting and resolving technical issues with Cisco products and technologies. The website is
available 24 hours a day at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com
user ID and password. If you have a valid service contract but do not have a user ID or password, you
can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Obtaining Technical Assistance
Note Use the Cisco Product Identification Tool to locate your product serial number before submitting a
request for service online or by phone. You can access this tool from the Cisco Technical Support &
Documentation website by clicking the Tools & Resources link, clicking the All Tools (A-Z) tab, and
then choosing Cisco Product Identification Tool from the alphabetical list. This tool offers three search
options: by product ID or model name; by tree view; or, for certain products, by copying and pasting
show command output. Search results show an illustration of your product with the serial number label
location highlighted. Locate the serial number label on your product and record the information before
placing a service call.
Tip Displaying and Searching on Cisco.com
If you suspect that the browser is not refreshing a web page, force the browser to update the web page
by holding down the Ctrl key while pressing F5.
To find technical information, narrow your search to look in technical documentation, not the entire
Cisco.com website. On the Cisco.com home page, click the Advanced Search link under the Search box
and then click the Technical Support & Documentation radio button.
To provide feedback about the Cisco.com website or a particular technical document, click Contacts &
Feedback at the top of any Cisco.com web page.
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
45
Page 46
Obtaining Additional Publications and Information
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and
S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411
Australia: 1 800 805 227
EMEA: +32 2 704 55 55
USA: 1 800 553 2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—An existing network is “down” or there is a critical impact to your business operations.
You and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operations are negatively affected by inadequate performance of Cisco products. You and
Cisco will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of the network is impaired while most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
• The Cisco Online Subscription Center is the website where you can sign up for a variety of
Cisco e-mail newsletters and other communications. Create a profile and then select the
subscriptions that you would like to receive. To visit the Cisco Online Subscription Center,
go to this URL:
http://www.cisco.com/offer/subscribe
46
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
78-17975-01
Page 47
Obtaining Additional Publications and Information
• The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief
product overviews, key features, sample part numbers, and abbreviated technical specifications for
many Cisco products that are sold through channel partners. It is updated twice a year and includes
the latest Cisco channel product offerings. To order and find out more about the Cisco Product Quick
Reference Guide, go to this URL:
http://www.cisco.com/go/guide
• Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo
merchandise. Visit Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
• Cisco Press publishes a wide range of general networking, training, and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
• Networking products offered by Cisco Systems, as well as customer support services, can be
obtained at this URL:
http://www.cisco.com/en/US/products/index.html
• Networking Professionals Connection is an interactive website where networking professionals
share questions, suggestions, and information about networking products and technologies with
Cisco experts and other networking professionals. Join a discussion at this URL:
http://www.cisco.com/discuss/networking
• “What’s New in Cisco Documentation” is an online publication that provides information about the
latest documentation releases for Cisco products. Updated monthly, this online publication is
organized by product category to direct you quickly to the documentation for your products. You
can view the latest release of “What’s New in Cisco Documentation” at this URL:
http://www.cisco.com/univercd/cc/td/doc/abtunicd/136957.htm
• World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
78-17975-01
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
47
Page 48
Obtaining Additional Publications and Information
gyggyy
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco
ertified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
nterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS,
Phone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers,
etworking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient,
nd TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
ll other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a
artnership relationship between Cisco and any other company. (0711R)
© 2006 Cisco Systems, Inc. All rights reserved.
Printed in the USA on recycled paper containing 10% postconsumer waste.
Regulatory Compliance and Safety Information for the Cisco Global Site Selector 4492R
48
78-17975-01
Loading...