Cisco Aironet 1530 Series, 1532 Installation Manual

Page 1

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

December, 2013

Cisco Systems, Inc.

www.cisco.com

Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.

Text Part Number: OL-30864-01

Page 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Page 3

Preface vii

Objectives vii

Audience vii

Organization viii

Conventions viii

Objectives

Preface

This section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide.

Audience

Warning

This publication explains the steps for installing the Cisco Aironet 1530 Series Outdoor Access Point (called the access point in this document). The access point is available in an internal antenna (1532I) or an external antenna (1532E) version.

The 1532 model is a dual-radio platform that supports dual-band (2.4- and 5-GHz) operation.

This publication is for the person installing and configuring an access point for the first time. The installer should be familiar with network structures, terms, and concepts.

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

This equipment must be installed in restricted access locations in Norway, Finland, and Sweden. Only trained and qualified personnel are allowed to install, replace, or service this equipment as instructed in this installation guide.

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

vii

Page 8

Organization

This guide contains the following sections:

Chapter Title Description

Chapter 1 Overview Describes the major components and features

Chapter 2 Installing the Access Point Provides warnings, safety information, and

Chapter 3 Troubleshooting Provides basic troubleshooting procedures for

Appendix A Translated Safety Warnings Indicates how to access the document that

Appendix B Declarations of Conformity

Appendix C Channels and Power Levels Indicates how to access the document that lists

Appendix D Access Point Data Sheet Lists technical specifications for the access

Appendix E Access Point Pinouts Describes the connector pinouts for the access

Appendix F Configuring DHCP Option 43Describes the procedure to configure DHCP

and Regulatory Information

of the access point.

mounting information you need to install your access point.

the access point.

provides translations of the safety warnings that appear in this publication.

Describes the regulatory conventions to which the access point conforms and provides guidelines for operating access points in Japan.

the access point radio channels and the maximum power levels supported by the world regulatory domains.

point.

Option 43.

Conventions

This publication uses the following conventions:

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

viii

Convention Description

boldface font Commands, command options, and keywords are

in boldface.

italic font Arguments for which you supply values are in

italics.

[ ] Elements in square brackets are optional.

screen font

boldface screen font

italic screen font

Terminal sessions and information the system displays are in screen font.

Information you must enter is in boldface screen font.

Arguments for which you supply values are in italic screen font.

OL-30864-01

Page 9

Convention Description

^ The symbol ^ represents the key labeled Control.

For example, the key combination ^D in a screen display means hold down the Control key while you press the D key.

< > Nonprinting characters, such as passwords, are in

angle brackets.

Notes use the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in

this manual.

Cautions use the following conventions:

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Warning

Waarschuwing

Warnings use the following conventions:

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Statement 1071

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Page 10

Varoitus

Attention

Warnung

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

Avvertenza

Advarsel

BEWAHREN SIE DIESE HINWEISE GUT AUF.

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 11

Aviso

¡Advertencia!

Varning!

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

Figyelem

SPARA DESSA ANVISNINGAR

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Page 12

Aviso

Advarsel

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

xii

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 13

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

xiii

Page 14

Finding the Product Serial Number

The access point serial number is on the side of the access point (refer to Figure 1).

xiv

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 15

Figure 1 Location of Serial Number Label

OL-30864-01

The access point serial number label contains the following information:

• Model number, such as AIR-CAP1532E-x-K9.

• Serial number, such as WCN0636279B (11 alphanumeric digits).

• Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located

under the serial number.

You need your product serial number when requesting support from the Cisco Technical Assistance Center.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Page 16

Obtaining Documentation, Support, and Security Guidelines

For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

To view all new wireless documentation, click on Wireless.

xvi

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 17

Overview

The Cisco Aironet 1530 Series Outdoor Access Point (hereafter called the access point or AP) is a wireless outdoor access point which is designed for use in a variety of network configurations. The access point supports wireless client access, point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity.

About the 1532 Access Point

The 1532 access point supports two radios (2.4-GHz and 5-GHz) and provides client access using the unlicensed RF Wi-Fi spectrum. The 2.4 GHz radio is used for client access and the 5 GHz radio can be dedicated for backhaul traffic or can used for both backhaul and client access. Depending on the radio, the access point can support 1 to 300 Mb/s data rates (for specific data rates, refer to Appendix D,

“Access Point Data Sheet”).

The access point is a standalone unit that can be wall, pole or tower mounted. The access point can also operate as a relay node for other access points not directly connected to a wired network. Intelligent wireless routing is provided by the patented Adaptive Wireless Path Protocol (AWPP). This enables each access point to identify its neighbors and intelligently choose the optimal path to the wired network by calculating the cost of each path in terms of signal strength and the number of hops required to get to a controller.

CHA P T ER

OL-30864-01

The access point can be configured, monitored, and operated through a Cisco wireless LAN controller (hereafter called a controller) as described in the Cisco Wireless LAN Controller Configuration Guide. The Cisco Wireless Mesh Access Points, Design and Deployment Guide, Release 7.6 describes how to plan and initially configure the Cisco mesh network, which supports wireless point-to-point, point-to-multipoint, and mesh deployments. The controllers use a browser-based management system, a command-line interface (CLI), or the Cisco Prime Infrastructure (PI) network management system to manage the controller and the associated access points. The access point supports hardware-based advanced encryption standard (AES) encryption between wireless nodes to provide end-to-end security. The access point can also be deployed in an autonomous mode and be configured via the CLI.

This chapter provides information on the following topics:

• Hardware Models, page 1-2

• Hardware Features, page 1-3

• Network Deployment Examples, page 1-11

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-1

Page 18

Hardware Models

The model numbers (or part numbers) and configuration for the Cisco Aironet 1532 Outdoor Access Points are described in Tab l e 1-1.

For a detailed description of the declarations of conformity and regulatory information for the 1532 access points refer to Appendix B, “Declarations of Conformity and Regulatory Information.”

Table 1-1 1532 Access Point Model Numbers and Descriptions

Model (or part number) Configuration

AIR-CAP1532I-x-K9

AIR-AP1532I-UXK9

AIR-CAP1532E-x-K9

AIR-AP1532E-UXK9

Chapter 1 Overview

The AP 1532I has integrated antennas and contains a 2.4 GHz and 5 GHz radio with an option to configure in centralized, Flexconnect, or mesh mode. This is a stand alone unit that can be wall, pole or tower mounted. It can also operate as a relay node for other access points that are not directly connected to a wired network.

The AP 1532E has 4 external antenna ports and contains a 2.4 GHz and 5 GHz radio with an option to configure in centralized, Flexconnect, or mesh mode. This is a stand alone unit that can be wall, pole or tower mounted. It can also operate as a relay node for other access points that are not directly connected to a wired network.

Regulatory Domains

The “-x” in the 1532 model numbers represent the domain. For example, in AIR-CAP1532I-x-K9, the -x represents a regulatory domain for a specific country.

The 1530 series will also support the universal regulatory domain, -UX, which will have the following model number format:

• AIR-AP1532I-UXK9

• AIR-AP1532E-UXK9

For specific regulatory domains supported by each 1532 access point model, refer to the Wireless LAN Compliance Status at the following URL:

http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd805 37b6a.html

To locate the 1532 access point models, click on 802.11abgn Outdoor Access Points.

1-2

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 19

Chapter 1 Overview

347850

Hardware Features

This section describes the hardware features of the 1532 access point models. The following hardware features are described in this section:

• Connectors, page 1-3

• Antenna Port Locations, page 1-7

• Multiple Power Sources, page 1-8

• Ethernet (PoE) Ports, page 1-10

• Optional Hardware, page 1-10

Connectors

Figure 1-4 and Figure 1-5 show the access point connectors for all models. Figure 1-1 shows the bottom

connectors for internal antenna model, and Figure 1-2 and Figure 1-3 show the external antenna Type-N connectors.

Hardware Features

Note The illustrations in this document show all available connections for the access point. Unused

connections are capped with a connector plug to ensure the watertight integrity of the access point. Liquid-tight adapters are provided for connector openings, which can be installed before or after deploying the access point.

1532I/1532E Connectors

Figure 1-1 Access Point Models AIR-CAP1532I-x-K9 Bottom Connectors

1 LAN port 2 POE-in port

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-3

Page 20

Hardware Features

347848

Chapter 1 Overview

Figure 1-2 Access Point Models AIR-CAP1532E-x-K9 Bottom Connectors

1 Antenna 1 port 2 Antenna 2 port 3 LAN port 4 POE-in port

Figure 1-3 Access Point Model AIR-CAP1532E-x-K9 Top Connectors

1-4

1 Antenna port 4 2 Antenna port 3

Note The AIR-CAP1532I-x-K9 does not have any top connectors.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

347847

OL-30864-01

Page 21

Chapter 1 Overview

1532I/E Connectors

Hardware Features

Figure 1-4 Access Point Model AIR-CAP1532I-x-K9 and AIR-CAP1532E-x-K9 Left Side Connectors

OL-30864-01

347845

1 Console port and Reset button (covered)

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-5

Page 22

Hardware Features

Chapter 1 Overview

Figure 1-5 Access Point Model AIR-CAP1532I-x-K9 and AIR-CAP1532E-x-K9 Right Side

Connectors

1-6

347846

1 Ground Pad 2 DC Power-In (covered)

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 23

Chapter 1 Overview

351321

Antenna Port Locations

Figure 1-6 shows the antenna port locations for model AIR-CAP1532E-x-K9. The ports used depend on

the optional antennas ordered.

Figure 1-6 External Antenna Port Locations for Access Point Models AIR-CAP1532E-x-K9

Hardware Features

1 Antenna port 1 – Type N connector 2 Antenna port 2- Type N connector 3 Antenna port 3– Type N connector (with cap) 4 Antenna port 4- Type N connector (with cap)

Radio Operation

Warning

In order to comply with radio frequency (RF) exposure limits, the antennas should be placed no less than 20 cm (8”) from your body or nearby persons.

Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.: NFPA 70, National Electric Code, Article 180, Canada: Canadian Electrical Code, Section 54).

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Statement 1052

Statement 339

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-7

Page 24

Hardware Features

AP1532I (Internal Antenna)

The 1532I access point 802.11b/g/n radio is used primarily for local access and its 802.11a/n radio for wireless backhaul in the Mesh.

The 2 GHz b/g/n radio operates in 2.4 GHz ISM band. It supports channels 1-11 in the US, 1-13 in Europe, and 1-13 in Japan. It has 3 transmitters with a maximum total output power of 29 dBm for

802.11b/g/n operation. Output power is configurable for 8 levels in 3 dB steps. It has three receivers that enable maximum-ratio combining (MRC).

The 5 GHz a/n radio operates in the UNII-2 band (5.25 - 5.35 GHz), UNII-2 Extended/ETSI band (5.47

- 5.725 GHz), and the upper ISM band (5.725 - 5.850 GHz). It has two transmitters with a maximum total output power of 27 dBm depending on the regulatory domain. The total maximum output power for the upper ISM band is 27 dBm for A-domain. Tx power settings will change depending on the regulatory domain. Output power is configurable in 3 dB steps. Its three receivers enable maximum-ratio combining (MRC).

The 1532I access point is equipped with three integrated dual-band antennas with 3 dBi gain at 2 GHz and 5 dBi gain at 5 GHz.

AP1532E (External Antenna)

Chapter 1 Overview

The 1532E access point is equipped with four N-type RF connectors. The 1532E can be configured via software to support dual band or single band antennas. When configured for dual band antennas, antenna ports 1 and 2 on the bottom of the unit (Figure 1-2) are used to support multiple input/multiple output (MIMO) operation on both 2.4 and 5 GHz radios. When using the Cisco Aironet AIR-ANT2547V-N or AIR-ANT2547VG-N omindirectional antennas, the antenna can be connected directly to the access point (Figure 2-16). If the antennas are remotely located, an appropriate low loss RF cable should be used.

Note Ensure that the antenna band mode is configured before the 1532E access point is installed.

When configured for single band antennas, antenna port 1 and antenna port 2 support MIMO operation for the 2.4 GHz radio, and antenna ports 3 and 4 (Figure 1-3) support MIMO on the 5 GHz radio. See the Cisco Wireless LAN Controller Configuration Guide for information on the software configuration.

Multiple Power Sources

The 1530 series access point supports these power sources:

• DC power – 24-57 VDC

• Power over Ethernet (PoE) – For more information, see “Powering the Access Point” section on

page 2-40.

1-8

Warning

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Installation of the equipment must comply with local and national electrical codes.

This equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Statement 366

Statement 1074

OL-30864-01

Page 25

Chapter 1 Overview

Hardware Features

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

Caution Several forms of PoE are supported. See Table Tabl e 2-7 for the PoE options and their corresponding

Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Statement 1033

Statement 1023

modes of operation.

Caution Do not place the power injector in an unprotected outdoor environment because water could get into the

power injector and cause a short circuit and possible fire.

Caution When the access point is installed outdoors or in a wet or damp location, the AC branch circuit that is

powering the access point should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).

Power injectors

Warning

Caution The power injector (AIR-PWRINJR4- and AIR-PWRINJ1500-2=) must be used in an indoor

Caution When the access point is installed outdoors, or in a wet or damp location, the AC branch circuit that is

The 1530 series access points support the following power injectors:

• AIR-PWRINJ1500-2= – 100-240 VAC input, indoor use only

• AIR-PWRINJ4= – 100-240 VAC input, indoor use only

To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

Statement 1023

environment only.

powering the access point should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-9

Page 26

Hardware Features

Ethernet (PoE) Ports

The access point supports an Ethernet uplink port (PoE-In). The access point Ethernet uplink port uses an RJ-45 connector (with weatherproofing) to link the access point to the 10BASE-T, 100BASE-T or 1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to optionally supply inline power from the power injector or a suitably powered switch port.

Tip The access point senses the Ethernet and power signals and automatically switches internal circuitry to

match the cable connections.

Chapter 1 Overview

Warning

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

The Ethernet cable must be a shielded outdoor rated Category 5e (CAT5e) or better cable. The access point senses the Ethernet and power signals and automatically switches internal circuitry to match the cable connections.

Optional Hardware

Depending on what you ordered, the following optional access point hardware may be part of your shipment:

• External antennas, depending on which ones you purchased (See “AP1532E (External Antenna)”

section on page 1-8 for information on available external antennas.)

• Wall/Pole mount bracket (AIR-ACC1530-PMK1 [=])

• Wall/Pole mount bracket with tilt mechanism, spare only (AIR-ACC1530-PMK2=)

• Street light power tap (AIR-PWR-ST-LT-R3P=), works only with the AC/DC power adapter.

• Power injector (AIR-PWRINJ1500-2=, AIR-PWRINJ4=)

• AP cover / Solar Shield for 1532, spare only (AIR-ACC1530-CVR=)

• AC/DC power adapter, spare only (AIR-PWRADPT-1530=)

• Spare Parts kit containing extra cable glands, power connector, ground lug, etc.

(AIR-ACC1530-KIT1=)

Statement 1023

1-10

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 27

Chapter 1 Overview

Network Deployment Examples

The access point is a wireless device designed for wireless client access and point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. The access point provides 5-GHz backhaul capability to link with another access point to reach a wired network connection or to provide repeater operations for other access points.

The access point plays two primary radio roles: a root access point (hereafter called a RAP) or a mesh (non-root) access point (hereafter called a MAP), which is the default role of all access points. When the access point has a fiber or wired Ethernet connection to the controller (through a switch), the radio role is called a RAP. In order to be considered a RAP, the access point must be configured as a RAP. A RAP is a parent node to any bridging or mesh network. A controller can support one or more RAPs, each one parenting the same or different wireless networks. There can be more than one RAP for the same mesh network for redundancy. RAPs and MAPs can support wireless clients on the 2.4-GHz and 5-GHz band. Client access on 5-GHz is called universal client access.

When the access point does not have a wired Ethernet connection to the controller (through a switch), the radio role is called a MAP. The MAPs have a wireless connection (through the backhaul interface) to other MAPs and finally to a RAP which has an Ethernet connection through a switch to the controller. MAPs may also have a wired Ethernet connection to a local LAN and serve as a bridge endpoint for that LAN (using a point-to-point or point-to-multipoint bridge connection).

Network Deployment Examples

Wireless Backhaul

The access point supports wireless backhaul capability using the 5 GHz radio to bridge to another access point to reach a wired network connection to a controller (see Figure 1-7). The access point connected to the wired network is considered a RAP in this configuration. The remote access point is considered a MAP and transfers wireless client traffic to the RAP for transfer to the wired network. Control And Provisioning of Wireless Access Points (CAPWAP) control traffic is also transferred over this bridged link.

Figure 1-7 Access Point Backhaul Example

Point-to-Point Bridging

(5 GHz)

(2.4 GHz and 5 GHz)

255493

OL-30864-01

The access points can be used to extend a remote network by using the 5 GHz backhaul radio to bridge the two network segments as shown in Figure 1-8. To support Ethernet bridging, you must enable bridging on the controller for each access point. By default this capability is turned-off for all access points.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-11

Page 28

Network Deployment Examples

352052

2.4 GHz or 5 GHz

Wireless client access is supported; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access.

Figure 1-8 Access Point Point-to-Point Bridging Example

The access points can also support point-to-point bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge.

Figure 1-9 Access Point Point-to-Point Bridging in Autonomous Mode

Chapter 1 Overview

(5 GHz)

255495

Point-to-Multipoint Bridging

The access points can be used as a RAP to connect multiple remote MAPs with their associated wired networks. By default this capability is turned-off for all access points. To support Ethernet bridging, you must enable bridging on the controller for each access point. Wireless client access can be provided over the bridging link; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-10 illustrates an example of access point-to-multipoint bridging.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-12

OL-30864-01

Page 29

Chapter 1 Overview

255494

(5 GHz)

352051

2.4 GHz or 5 GHz

Network Deployment Examples

Figure 1-10 Access Point to Multipoint Bridging Example

The access points can also support point-to-multipoint bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge.

Figure 1-11 Access Point to Multipoint Bridging in Autonomous Mode

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-13

Page 30

Network Deployment Examples

Point-to-Multipoint Mesh Network

The access point is typically deployed in a mesh network configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller. Other remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network. In the mesh network, the links between the access points are referred to as the backhaul links.

Intelligent wireless routing is provided by the Adaptive Wireless Path protocol (AWPP). This enables each MAP to identify its neighbors and intelligently choose the optimal path to the RAP with the wired network connection by calculating the cost of each path in terms of signal strength and the number of hops required to get to a controller with signal strength given priority since signal strength determines the data rate available for backhaul.

Figure 1-12 illustrates a typical mesh configuration using MAPs and RAPs.

Figure 1-12 Typical Mesh Configuration Using Access Points

Chapter 1 Overview

Network

CPI

MAP 4

MAP 1

MAP 2

MAP 5

RAP

MAP 3

MAP 6

1-14

MAP 7

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

MAP 8

MAP 9

351994

OL-30864-01

Page 31

Chapter 1 Overview

Layer 3 Network Operation

The access points support Layer 3 network operation. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Cisco.

Figure 1-13 illustrates a typical Layer-3 wireless network configuration containing access points and a

controller.

Figure 1-13 Typical Layer 3 Access Point Network Configuration Example

Network Deployment Examples

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

1-15

Page 32

Network Deployment Examples

Chapter 1 Overview

1-16

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 33

CHA P T ER

Installing the Access Point

This chapter describes how to install the 1532 access point and contains the following sections:

• Unpacking the Access Point, page 2-2

• Tools and Hardware, page 2-2

• Warnings, page 2-3

• Safety Information, page 2-4

• Avoiding Damage to Radios in a Testing Environment, page 2-6

• Installation Guidelines, page 2-6

• Mounting the Access Point, page 2-11

• Installing Antennas, page 2-28

• Grounding the Access Point, page 2-40

• Powering the Access Point, page 2-40

• Configuring the Access Point, page 2-52

• What to Do Next, page 2-53

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-1

Page 34

Unpacking the Access Point

To unpack the access point, follow these steps:

Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container, and save it. Step 3 Ensure that all items listed in “Package Contents” are included in the shipment. If any item is damaged

or missing, notify your authorized Cisco sales representative.

Package Contents

Each access point package contains the following items:

• One 1530 series access point

• Two-pin DC power connector

Chapter 2 Installing the Access Point

• Ground lug and screws with lock washers

• Plastic cable gland and rubber seal

• Weatherization tape and anti-corrosion sealant

• Cisco product documentation and pointer card

Tools and Hardware

The tools and hardware used to install the 1532 access point are described in:

• Optional Tools and Hardware, page 2-2

• Optional Tools and Hardware That You Supply, page 2-3

• Warnings, page 2-3

Optional Tools and Hardware

Depending on what you ordered, the following optional equipment may be part of your shipment:

• External antennas, depending on which ones you purchased (see “Antenna Configurations” section

on page 2-29 for more information).

• Wall/Pole mount bracket, available as an option or a spare (AIR-ACC1530-PMK1[=])

2-2

• Wall/Pole mount bracket with tilt mechanism, spare only (AIR-ACC1530-PMK2=)

• AP cover / Solar Shield for 1532, spare only (AIR-ACC1530-CVR=)

• AC/DC power adapter, spare only (AIR-PWRADPT-1530=)

• Spare Parts kit containing extra cable glands, power connector, ground lug, etc.

(AIR-ACC1530-KIT1=)

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 35

Chapter 2 Installing the Access Point

• FIPS kit (AIRLAP-FIPSKIT=)

• Lightning Arrestor kit (AIR-ACC245LA-N=)

Optional Tools and Hardware That You Supply

Tools and materials that are user-supplied are:

• Ground lug crimping tool (Panduit CT-720 with CD-720-1 die)

• 6-AWG copper ground wire

• 10 mm open end or box wrench

• 13 mm box-end wrench or socket set

• Adjustable wrench with opening up to 33 mm and 28 mm socket.

• Large flat or phillips screw driver (for port plugs)

• Small flat screwdriver for DC power connector

• Optional shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.20 to 0.35 in

(0.51 to 0.89 cm) diameter

• Optional Ethernet RJ-45 connector and installation tool

Warnings

Warning

• Optional shielded outdoor-rated DC power cable with 0.20 to 0.35 inch (.0.51 to 0.89 cm) diameter

• Optional ground rod, as required by local regulations

• Optional ladder, power lift, rope, or other tools as required

Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A,

“Translated Safety Warnings” for instructions.

IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining any required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.

OL-30864-01

Warning

Do not operate the unit near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Statement 364

2-3

Page 36

Safety Information

Chapter 2 Installing the Access Point

Warning

The cables specified in this installation guide that are used with the specified cable glands provide protection against ingress of moisture for a Type 4/IP67 classified enclosure. If substitute cable are used, the installer must ensure that the size (OD) of the cable meets the acceptable range allowed by the cable gland.

Read the installation instructions before connecting the system to the power source.

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

Statement 366

Statement 1004

FCC Safety Compliance Statement

The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results in user exposure substantially below the FCC recommended limits.

Safety Precautions

Warning

In order to comply with radio frequency (RF) exposure limits, the antennas should be placed no less than 20 cm (8”) from your body or nearby persons.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Statement 1022

Statement 339

2-4

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 37

Chapter 2 Installing the Access Point

Safety Information

Warning

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Statement 1023

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

Statement 1028

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards.

Statement 1033

When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046.

Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).

Statement 1052

OL-30864-01

Caution Before connecting or disconnecting a power cord, you must remove power from the power cord using a

suitable service disconnect.

For safety and to achieve a good installation, please read and follow these safety precautions:

• Select your installation site with safety, as well as performance in mind. Remember: electric power

lines and phone lines look alike. For safety, assume that any overhead line can kill.

• Call your electric power company. Tell them your plans, and ask them to come look at your proposed

installation.

• Plan your installation carefully and completely before you begin. Successful raising of a mast or

tower is largely a matter of coordination. Each person should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble.

• When installing the access point and antennas, remember:

–

Do not use a metal ladder.

–

Do not work on a wet or windy day.

–

Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.

• Use a rope to lift the access point. If the assembly starts to drop, get away from it and let it fall.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-5

Page 38

Chapter 2 Installing the Access Point

Avoiding Damage to Radios in a Testing Environment

• If any part of the antenna system should come in contact with a power line, do not touch it or try to

remove it yourself. Call your local power company. They will remove it safely.

If an accident should occur, call for qualified emergency help immediately.

Avoiding Damage to Radios in a Testing Environment

The radios on outdoor units (bridges) have higher transmit power levels than radios on indoor units (access points). When you test high-power radios in a link, you must avoid exceeding the maximum receive input level for the receiver. At levels above the normal operating range, packet error rate (PER) performance is degraded. At even higher levels, the receiver can be permanently damaged. To avoid receiver damage and PER degradation, you can use one of the following techniques:

• Separate the omnidirectional antennas by at least 2 ft (0.6 m) to avoid receiver damage or by at least

25 ft (7.6 m) to avoid PER degradation.

Note These distances assume free space path loss and are conservative estimates. Required separation

distances for damage and performance degradation levels in actual deployments are less if conditions are not non-line-of-sight.

•

Reduce the configured transmit power to the minimum level.

• Use directional antennas, and keep them away from each other.

• Cable the radios together using a combination of attenuators, combiners, or splitters to achieve a total

attenuation of at least 60 dB.

For a radiated test bed, the following equation describes the relationships among transmit power, antenna gain, attenuation, and receiver sensitivity:

txpwr + tx gain + rx gain - [attenuation due to antenna spacing] < max rx input level Where: txpwr = Radio transmit power level tx gain = transmitter antenna gain rx gain = receiver antenna gain

For a conducted test bed, the following equation describes the relationships among transmit power, antenna gain, and receiver sensitivity:

txpwr - [attenuation due to coaxial components] < max rx input level

Caution Under no circumstances should you connect the antenna port from one access point to the antenna port

of another access point without using an RF attenuator. If you connect antenna ports, you must not exceed the maximum survivable receive level of 0 dBm. Never exceed 0 dBm, or damage to the access point can occur. Using attenuators, combiners, and splitters having a total of at least 60 dB of attenuation ensures that the receiver is not damaged and that PER performance is not degraded.

Installation Guidelines

Because the access point is a radio device, it is susceptible to common causes of interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:

• For information on planning and initially configuring your Cisco Mesh network, refer to the Cisco

Wireless Access Points, Design and Deployment Guide, Release 7.3.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-6

OL-30864-01

Page 39

Chapter 2 Installing the Access Point

• Review the FCC guidelines for installing and operating outdoor wireless LAN devices at

• Perform a site survey before beginning the installation.

• Install the access point in an area where structures, trees, or hills do not obstruct radio signals to and

• The access points can be installed at any height, but best throughput is achieved when all the access

Note To calculate path loss and to determine how far apart to install access points, consult an RF planning

expert.

Site Surveys

Every network application is a unique installation. Before installing multiple access points, you should perform a site survey to determine the optimum use of networking components and to maximize range, coverage, and network performance.

Site surveys reveals problems that can be resolved before the network is operational. Because

802.11a/b/g/n operates in an unlicensed spectrum, there may be sources of interference from other

802.11a wireless devices (especially in multi-tenant buildings) that could degrade your 802.11 signals. A site survey can determine if such interference exists at the time of deployment.

Installation Guidelines

http://www.cisco.com/en/US/partner/prod/collateral/routers/ps272/data_sheet_c78-647116_ps114 51_Products_Data_Sheet.html.

from the access point.

points are mounted at the same height. We recommend installing the access points no higher than 40 feet to allow support for wireless clients on the ground.

A proper site survey involves temporarily setting up mesh links and taking measurements to determine whether your antenna calculations are accurate. Determine the correct locations and antenna types before you drill holes and route cables and mounting equipment.

Consider the following operating and environmental conditions when performing a site survey:

• Data rates—Sensitivity and range are inversely proportional to data bit rates. The maximum radio

range is achieved at the lowest workable data rate. A decrease in receiver sensitivity occurs as the radio data increases.

• Antenna type and placement—Proper antenna configuration is a critical factor in maximizing radio

range. As a general rule, range increases in proportion to antenna height. However, do not place the antenna higher than necessary, because the extra height also increases potential interference from other unlicensed radio systems and decreases the wireless coverage from the ground.

• Physical environment—Clear or open areas provide better radio range than closed or filled areas.

• Obstructions—Physical obstructions such as buildings, trees, or hills can hinder performance of

wireless devices. Avoid locating the devices in a location where there is an obstruction between the sending and receiving antennas.

• How far is your wireless link?

• Has a previous site survey been conducted?

• Do you have a clear Fresnel zone between the access points or radio line of sight?

• What is the minimum acceptable data rate within the link?

• Do you have the correct antenna (if more than one antenna is being offered?)

OL-30864-01

• Do you have access to both of the mesh site locations?

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-7

Page 40

Installation Guidelines

• Do you have the proper permits, if required?

• Are you following the proper safety procedures and practices?

• Have you configured the access points before you go onsite? It is always easier to resolve

configurations or device problems first.

• Do you have the proper tools and equipment to complete your survey.

Before Beginning the Installation

Before you begin the installation process:

• Ensure that a site survey has been performed.

• Ensure that your network infrastructure devices are operational and properly configured.

• Ensure that your controllers are connected to switch trunk ports.

• Ensure that your switch is configured with untagged access ports for connecting your access points.

• Ensure that a DHCP server with Option 43 configured is reachable by your access points, or

manually configure the controller information in the access point (for additional information, refer to the “Configuring DHCP Option 43” section on page F-1).

• Become familiar with the access point installation components (see the “Becoming Familiar with

Access Point Installation Components” section on page 2-8).

Chapter 2 Installing the Access Point

Becoming Familiar with Access Point Installation Components

The access point is designed to be installed in an outdoor environment, such as the exterior roof overhang of a tall building or a streetlight pole. Carefully review the following figures to become familiar with the system components, connectors, indicators, cables, system interconnection, and grounding:

• Components in a typical access point installation (see Figure 2-1)

• Pole mount installation (see Figure 2-2)

• Streetlight power tap installation, works only with the AC/DC power adapter (see Figure 2-3). Note

that this type of deployment requires an alternate AP mounting kit. See Mounting the Access Point section for more information.

Note The illustrations in this document show all available connections for the access point. Unused

connections are capped with a connector plug to ensure the watertight integrity of the access point. Cable glands are provided for connector openings, which can be installed before or after deploying the access point.

2-8

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 41

Chapter 2 Installing the Access Point

Figure 2-1 Components in a Typical Access Point Installation

Installation Guidelines

10 8

351963

1 Building roof-overhang 6 Ground 2 Shielded outdoor-rated Ethernet

(CAT5e or better) cable

7 Power cord

3 Water drip loop 8 Power injector 4 6-AWG copper grounding wire

9 Shielded Ethernet (CAT5e or better) cable

5 Ground rod1 10 Controller (through a switch)

1. User supplied.

OL-30864-01

Warning

Installation of the equipment must comply with local and national electrical codes.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Statement 1074

2-9

Page 42

Installation Guidelines

AC/DC Adapter

Chapter 2 Installing the Access Point

Figure 2-2 Standard Pole Mount Installation

1 1532 series access point model

3 Mounting bracket (part of pole mount kit)

AIR-CAP1532E-x-K9

2 One of four M6 AP mount hole and key hole

slots

4 Stainless steel mounting straps (part of pole

mount kit)

5 Pole (wood, metal, or fiberglass)

2 in. to 8 in. (50 mm to 203 mm) diameter

Figure 2-3 Streetlight Power Tap Adapter Installation

1 Outdoor light control 3 6-AWG copper grounding wire 2 AC/DC power adapter

2-10

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 43

Chapter 2 Installing the Access Point

Mounting the Access Point

This section provides instructions for installing your access points. Personnel installing the access point must understand wireless access points and bridging techniques and grounding methods.

Caution All installation methods for mounting an access point on any wall surface is subject to the acceptance of

local jurisdiction.

Installation Options

The 1530 Series Access Point can be wall, pole or tower mounted.There are two optional mounting kits: a fixed mounting kit (AIR-ACC1530-PMK1=) and a pivoting mounting kit (AIR-ACC1530-PMK2=).

Mounting the Access Point

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Installation of the equipment must comply with local and national electrical codes.

Access Point Mounting Orientation

When mounting an access point on a horizontal or vertical surface, you must ensure that the access point is oriented with the LED indicators pointing down. This positioning allows LEDs to be visible to someone on the ground below the access point.

You must also ensure the access point is mounted in such a way as to ensure that all antenna ports and the console port are accessible for future use.

Note Omnidirectional antennas are vertically polarized and should be mounted vertically.

Wall Mounting the Access Point with the Fixed Mounting Kit

The optional fixed mounting kit contains a mounting bracket for wall mounting or pole mounting. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation. You then install the mounting plate, and attach the access point when you are ready.

Table 2-1 lists the materials you will need to provide in addition to the fixed mounting kit.

Statement 1074

OL-30864-01

Ta b l e 2 - 1 Materials Required to Mount Access Point to a Vertical Wall

Materials Required to Mount Access Point to a Vertical Wall In Kit

Ground lug and screws (provided with access point) Yes

Wall Mount Bracket Yes

Four M6 x 12-mm Hex-head Bolts Yes

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-11

Page 44

Mounting the Access Point

Materials Required to Mount Access Point to a Vertical Wall In Kit

Two stainless steel band clamps (adjustable 2"–5", 51 mm – 127 mm)

Two stainless steel band clamps(adjustable 5"–8", 127 mm – 203 mm)

Crimping tool for ground lug, Panduit CT-720 with CD-720-1 die (http://www.panduit.com)

Four wall mounting screws No

Four wall anchors (specified for all material) No

Drill bit for wall anchors No

Electric drill and standard screwdriver No

#6 AWG ground wire No

Shielded outdoor-rated Ethernet (CAT5e or better) cable No

Grounding block No

Grounding rod No

10-mm box-end wrench or socket set No

Chapter 2 Installing the Access Point

Yes

Caution The mounting surface, attaching screws and optional wall anchors must be able to support a

50-lb (22.7 kg) static weight.

To mount the access point on a vertical wall, follow these instructions:

Step 1 Use the mounting bracket as a template to mark four screw hole locations on the mounting surface.

See Figure 2-4 for the mounting bracket screw hole locations. Use the mounting slotted holes to attach the unit to the wall.

2-12

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 45

Chapter 2 Installing the Access Point

347852

Figure 2-4 Mounting Bracket for Wall and Pole Mounting

Mounting the Access Point

1 Quick Mount Keyhole Slots (for AP use) 2 Mounting Slots (used with the band clamps) 3 Bracket Mount Holes (use bolts up to 1/4" or

6 mm in diameter)

Step 2 Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the

mounting surface.

Note If necessary, use suitable screw anchors and an exterior-grade plywood backboard to mount the access

point to stucco, cement or drywall.

Figure 2-5 Mounting Bracket Dimensions

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-13

Page 46

Mounting the Access Point

Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do

not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space.

Step 4 Position the four bolts on the access point into the keyhole slots on the mounting bracket. Step 5 Slide the access point down to sit securely in the quick mount notches. Step 6 Using a 10mm wrench, secure the AP to the bracket by tightening the bolts to the bracket; torque to 40

lb-in.

Step 7 Continue with the Grounding the Access Point, page 2-40.

Pole Mounting the Access Point with the Fixed Mount Kit

The optional fixed mounting kit contains a mounting bracket for wall mounting or pole mounting.This kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.

Ta b l e 2 - 2 Materials Needed to Mount the AP on a Vertical Pole

Materials Needed to Mount the AP on a Vertical Pole In Kit

One wall mount bracket Yes

Four M6 x12mm hex head bolts Yes

Two stainless steel band clamps (adjustable 2"–5", 51–127 mm)

Two stainless steel band clamps (adjustable 5"–8", 127–203 mm)

10 mm box-end wrench No

Outdoor rated shielded ethernet cable No

Ground lug (provided with the access point) Yes

Ground block and rod No

Crimping tool for ground lug, Panduit CT-720 with CD-720-1 die (http://www.panduit.com)

#6 AWG ground wire No

Yes

Chapter 2 Installing the Access Point

2-14

To mount the access point onto a vertical pole or streetlight pole, follow these steps:

Step 1 Select a mounting location on the pole to mount the access point. You can attach the access point to any

pole with a diameter from 2to 8 inches (5.1 to 20.1 cm).

Note If you will be using a streetlight power tap adapter, position the access point within 3 ft (1 m) of

the outdoor light control. The AC/DC adapter must be used with street light power tap.

Step 2 Determine which size of band clamp is needed based on the pole diameter. Slide the two clamps through

the top and bottom set of mounting slots (see Figure 2-4) and mount the bracket to the pole.

Step 3 Wrap the band clamps around the pole and slide them into the second set of top and bottom mounting

slots on the bracket. Lightly tighten the clamps. Only tighten them enough to keep the bracket from sliding down the pole.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 47

Chapter 2 Installing the Access Point

Step 4 Screw an M6 bolt into each of the four bolt holes on the back side of the access point. Do not screw the

bolt in all the way. Leave a gap of about 0.13" (3.3mm).

Step 5 Position the four bolts on the access point into the bracket keyhole slots. Check to be sure that the access

point is properly seated in the slots.(See Figure 2-6)

Note The access point should be positioned with the LEDs on the bottom to allow viewing from the

ground.

Step 6 Using a 10mm wrench, tighten the four bolts that connect the access point to the bracket to a torque of

40 lbf-in.

Step 7 Locate the access point to its final position. Tighten the band clamps with the wrench so that the access

point does not slide on the pole. Ensure that the clamps are tight enough to not let the AP move.

Step 8 Continue with the Grounding the Access Point, page 2-40.

Mounting the Access Point

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-15

Page 48

Mounting the Access Point

351492

Figure 2-6 AP and Fixed Mount Kit Installed on a Pole

Chapter 2 Installing the Access Point

2-16

1 One of four M6 AP mount hole and key hole

slots

3 Mounting Slots 4 Pole

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2 Metal Band Straps

OL-30864-01

Page 49

Chapter 2 Installing the Access Point

351493

Wall Mounting the Access Point with the Pivoting Mounting Kit

The optional pivoting mounting kit contains a mounting bracket for wall or pole mounting. This kit can be used to install the access point on a wall while still allowing for some freedom of movement. This bracket supports metal, wood or fiberglass surfaces.

Figure 2-7 Pivoting Mounting Kit

Mounting the Access Point

1 Mounting holes for the AP 2 Slots for wall-mounting and band clamps. 3 Wall mount bracket.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

2-17

Page 50

Mounting the Access Point

352000

100

3.94

1.10

2.20

2x M8 THRU

4X 6.5MM THRU

17.10 .67

SLOT LENGTH

[4.0]

.16

SLOT WIDTH

Figure 2-8 Pivoting Mounting Kit Dimensions

Chapter 2 Installing the Access Point

Table 2-3 Materials for Mounting on Wall with Pivoting Mounting Kit

Materials Required for mounting AP on a vertical wall

In Kit

with pivoting mounting kit

Ground lug and screws (provided with access point) Yes

Pivoting mount kit and hardware Yes

(8) M6 x 12-mm Hex-head Bolts Yes

Adapter bracket for option horizontal mount Yes

Two stainless steel band clamps (adjustable 2"-5", 51 mm -

Yes

127 mm)

Two stainless steel band clamps (adjustable 5"-8", 127 mm 203 mm)

Crimping tool for ground lug, Panduit CT-720 with CD-720-1 die (http://www.panduit.com)

Yes

Four wall mounting screws (6mm max) No

Four wall anchors (specified for all material) No

Drill bit for wall anchors No

Electric drill and standard screwdriver No

#6 AWG ground wire No

Shielded outdoor-rated Ethernet (CAT5e or better) cable No

Grounding block No

Grounding rod No

2-18

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 51

Chapter 2 Installing the Access Point

351322

Mounting the Access Point

Materials Required for mounting AP on a vertical wall

In Kit

with pivoting mounting kit

13-mm box-end wrench or socket set No

10-mm box-end wrench No

Figure 2-9 AP wall mounted with Pivoting Mounting Kit

OL-30864-01

Caution The mounting surface, attaching screws and optional wall anchors must be able to support a 50-lb (22.7

kg) static weight.

To mount the access point on a vertical wall, follow these instructions:

Step 1 Disassemble pivot kit, if not already done. Step 2 Use the mounting bracket as a template to mark four screw hole locations on the mounting surface. See

Figure 2-7 for the mounting bracket screw hole locations (screw holes of maximum 6 mm in size).

Step 3 Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the

mounting surface.

Note If necessary, use suitable screw anchors and an exterior-grade plywood backboard to mount the access

point to stucco, cement or drywall.

Step 4 Match the holes in the bracket plate to the holes in the back of the access point. Step 5 Screw an M8 x12 mm bolt into each of the four bolt holes (using a 10 mm box wrench or socket, torque

the bolts to 40 lbf-in) on the back side of the access point and mounting bracket.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-19

Page 52

Chapter 2 Installing the Access Point

Mounting the Access Point

Step 6 Using the long bolt and the hardware supplied with the pivoting bracket, bolt the AP and its mounted

bracket, on to the bracket mounted on the wall (see Figure 2-11 for an exploded view of this assembly).

Step 7 Pivot the AP to your desired position, and then tighten the bolts (using a 13 mm wrench). Step 8 Continue with Grounding the Access Point, page 2-40.

Pole Mounting the Access Point with the Pivoting Mounting Kit

The optional pivoting mounting kit contains a mounting bracket for wall mounting or pole mounting, along with a clamp for pole mounting.This kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.

Figure 2-10 Pivoting Mounting Kit with Pole Mount Clamp

2-20

1 Mounting holes for the access point 2 Slots for band clamps (band clamps are

3 Pole mount clamp. It can fit poles of range up

to 3 in. (76mm)

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

provided but not shown in this figure. See

Figure 2-12).

OL-30864-01

Page 53

Chapter 2 Installing the Access Point

Figure 2-11 Exploded View of the Pivoting Mounting Kit

Mounting the Access Point

OL-30864-01

1 90.0 mm M8 screw 2 M8 washer 3 M8 spring washer 4 M8 nut 5 80.0 mm M8 screw with washer and spring

washer

Table 2-4 Materials Needed to Mount the AP on a Vertical Pole with the Pivoting Mounting Kit

Materials Required In Kit

Ground lug and screws (provided with access point) Yes

Pivoting mount kit and hardware Yes

(8) M6 x 12-mm Hex-head Bolts Yes

Adapter bracket for option horizontal mount Yes

Two stainless steel band clamps (adjustable 2"-5", 51 mm 127 mm)

Two stainless steel band clamps (adjustable 5"-8", 127 mm 203 mm)

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

Yes

2-21

Page 54

Mounting the Access Point

Materials Required In Kit

Crimping tool for ground lug, Panduit CT0720 with CD-720-1 die (http://www.panduit.com)

Four wall mounting screws (6mm max) No

Four wall anchors (specified for all material) No

Drill bit for wall anchors No

Electric drill and standard screwdriver No

#6 AWG ground wire No

Shielded outdoor-rated Ethernet (CAT5e or better) cable No

Grounding block No

Grounding rod No

13-mm box-end wrench or socket set No

10-mm box-end wrench No

To mount the access point onto a vertical pole or streetlight pole, follow these steps:

Chapter 2 Installing the Access Point

Step 1 Select a mounting location on the pole to mount the access point. You can attach the access point to any

pole with a diameter from 2 to 8 inches (5.1 to 40.6 cm).

Note If you will be using a streetlight power tap adapter, position the access point within 3 ft (1 m) of the

outdoor light control.

Step 2 Mount the pivot bracket base to the pole using either one set of the adjustable band clamps or the screw

clamp (the screw clamp can be used on a pole that is not more than 3 inches in diameter).

Step 3 Position the pole clamp bracket on the pole as needed before tightening the metal bands. Tighten the

metal bands only enough to hold the bracket base in place, from sliding along the pole. Fully tighten the bands only after the access point is positioned.

Step 4 Match the holes in the bracket plate to the holes in the back of the access point. Step 5 Screw an M8 x12 mm bolt into each of the four bolt holes (using a 10 mm box wrench or socket, torque

the bolts to 40 lbf-in) on the back side of the access point and mounting bracket. (See Figure 2-11)

Note The access point should be positioned with the LEDs on the bottom to allow viewing from the ground.

Step 6 Mount the bracket with the AP, to the bracket on the pole. Use the long screw for this, as shown in the

exploded view – see Figure 2-11.

Step 7 Point the AP in the general desired position and tighten bolt, and then tighten the clamps on the pole.

The AP can be repositioned to its final position by loosening and re-tightening the bolts.

2-22

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 55

Chapter 2 Installing the Access Point

347853

Figure 2-12 AP Pivot Mounted

Mounting the Access Point

1 Bolted Bracket Mounting Holes 2 Mounting Slots 3 Pole 4 Metal Band Mounting Straps.

For the kit which uses a clamp instead of metal bands, see Figure 2-10.

Step 8

Continue with the Grounding the Access Point, page 2-40

Horizontally Mounting the Access Point with Optional Horizontal Mount Plate

The pivoting pole mount kit also contains a plate that allows the option of the AP enclosure to be mounted horizontally (See Figure 2-13).

Table 2-5 Materials Needed to Mount the AP on a Vertical Pole with the Pivoting Mounting Kit

Materials Required In Kit

Ground lug and screws (provided with access point) Yes

Pivoting mount kit and hardware Yes

(8) M6 x 12-mm Hex-head Bolts Yes

Adapter bracket for option horizontal mount Yes

Two stainless steel band clamps (adjustable 2"-5", 51 mm 127 mm)

Two stainless steel band clamps (adjustable 5"-8", 127 mm 203 mm)

Crimping tool for ground lug, Panduit CT0720 with CD-720-1 die (http://www.panduit.com)

Four wall mounting screws (6mm max) No

Four wall anchors (specified for all material) No

Yes

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-23

Page 56

Mounting the Access Point

Materials Required In Kit

Drill bit for wall anchors No

Electric drill and standard screwdriver No

#6 AWG ground wire No

Shielded outdoor-rated Ethernet (CAT5e or better) cable No

Grounding block No

Grounding rod No

13-mm box-end wrench or socket set No

10-mm box-end wrench No

Step 1 Mount the pivot bracket to a wall or a pole as shown in the previous procedures. Step 2 Using four M6 x 12 mm bolts mount the horizontal adapter plate to the bracket mount plate.

Do not mount the pivot bracket mounting plate directly to the access point.

Step 3 Using the remaining four M6 x 12 mm bolts, mount the other side of the horizontal mounting plate to

the AP. See Figure 2-14 for the exploded view.

Chapter 2 Installing the Access Point

Step 4 Using a 10 mm wrench or socket, tighten all M6 bolts to 40 lbf-in (4.5 Nm). Step 5 Position the access point as needed and tighten the mount kit bolts using a 13 mm wrench or socket.

2-24

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 57

Chapter 2 Installing the Access Point

Figure 2-13 Access Point Horizontally Mounted using the Optional Horizontal Mount Plate

Mounting the Access Point

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-25

Page 58

Mounting the Access Point

Figure 2-14 Exploded View of a Horizontally Mounted Access Point

Chapter 2 Installing the Access Point

2-26

1 Pivoting bracket. Can be mounted on a pole or

a wall.

3 Screw holes for mounting the horizontal

mounting plate to the pivoting bracket

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2 Horizontal mounting plate

4 Screw holes for mounting the horizontal

mounting plate to the access point

OL-30864-01

Page 59

Chapter 2 Installing the Access Point

351999

Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=)

You can install an optional solar shield AIR-ACC1530-CVR= to cover the AP.

Note The cover can be installed prior to or after all connections are made. The only exception is when remote

cabled antennas are installed – in such cases, the shield must be installed before the antenna cables are attached to the AP.

Figure 2-15 Installing the Solar Shield

1 Solar Shield 2 Two of four #8-32 screws

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-27

Page 60

Installing Antennas

Step 1 Position and slide the cover over the AP as shown in Figure 2-15. Step 2 Align the two holes on each side of the cover with the screw holes on corresponding side of the AP. Step 3 Insert and install #8-32 screws through the screw holes in the cover and into the AP. Tighten the screws

to 10 lb-in.

Installing Antennas

Table 2- 6 shows the antennas supported by the 1532 access point and provides required quantities for

each model.

Table 2-6 1532 Access Point Supported External Antennas

Product ID

AIR-ANT2547VG-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (gray)

AIR-ANT2547V-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (white)

AIR-ANT2588P3M-N= 2.4 / 5 GHz 4 / 7 dBi Omnidirectional

AIR-ANT2588P3M-N 2.4 / 5 GHz 8 / 8 dBi Directional

AIR-ANT2450V-N 2.4 GHz 5 dBi Omnidirectional

AIR-ANT2480V-N 2.4 GHz 8 dBi Omnidirectional

AIR-ANT2413P2M-N= 2.4 GHz 13 dBi Directional

AIR-ANT5180V-N 5 GHz 8 dBi Omnidirectional

AIR-ANT5114P2M-N= 5 GHz 14 dBi Directional

Chapter 2 Installing the Access Point

Frequency Band Gain Type

For installation instructions and detailed information on these antennas, refer to the appropriate document located at:

http://www.cisco.com/en/US/products/hw/wireless/ps469/prod_installation_guides_list.html

Follow all safety precautions when installing the antennas. For information on safety, refer to “Safety

Precautions when Installing Antennas” section on page 2-29.

Non-Cisco Antennas

Cisco does not support any third-party antennas. RF connectivity and compliance of third party antennas is the customer’s responsibility. Cisco does not recommend any third-party antennas, and Cisco Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design and gain as Cisco antennas.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-28

OL-30864-01

Page 61

Chapter 2 Installing the Access Point

Safety Precautions when Installing Antennas

Installing Antennas

Warning

Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).

1. Before you install an antenna, contact your Cisco account representative to explain which mounting

Statement 280

method to use for the size and type of antenna that you are about to install.

2. Select your installation site with safety, as well as performance, in mind. Remember that electric

power lines and phone lines look alike. For your safety, assume that any overhead line can kill you.

3. Contact your electric power company. Tell them your plans and ask them to come look at your

proposed installation.

4. Plan your installation carefully and completely before you begin. Each person involved in an

installation should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble.

5. When installing your antenna, follow these guidelines:

–

Do not use a metal ladder.

–

Do not work on a wet or windy day.

–

Do dress properly—wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.

6. If the assembly starts to drop, move away from it and let it fall. Because the antenna, mast, cable,

and metal guy wires are all excellent conductors of electrical current, even the slightest touch of any of these parts to a power line completes an electrical path through the antenna and the installer.

7. If any part of the antenna system should come in contact with a power line, do not touch it or try to

remove it yourself. Call your local power company to have it removed safely.

8. If an accident should occur with the power lines, call for qualified emergency help immediately.

Antenna Configurations

Integrated Antenna Option

The AP1532I uses an Integrated Low Profile Dual-Band 2.4-5 GHz Dipole Antenna Array. The antenna contains an array of three dual-band dipole antennas. The three dipole antennas are contained within this single radome, thereby greatly reducing the antenna’s visual footprint, and greatly reducing the possibility of snagging the antenna on the cable bundle, the RF cable, or test cables. Each of thee three dipole antennas is a dual-band antenna, covering both the 2.4 - 2.483 GHz band and the 5.25-5.85 GHz bands. The antenna have a peak gain of about 3 dBi at 2.4 GHz and 5 dBi at 5 GHz. The antenna unit is gray weatherproof radome for outdoor operations.

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-29

Page 62

Installing Antennas

External Antenna Mounting Configurations

The selection of the antenna is determined in the configuration of the product. The 1532E antennas can be mounted on a wall, pole and/or tower mounted. Please refer to the Ordering Guide for a list of supported antennas.

The 1532E access point supports a variety of antennas designed for outdoor use with radios operating in the 2.4-GHz and 5-GHz frequency bands. The 1532 supports the external antennas listed in the following sections.

Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N)

The Dual-Band Omnidirectional Antenna, referred to as a “stick” antenna, is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz and 5-GHz frequency bands (Figure 2-16). Basic operating features of the antenna are:

• Omnidirectional colinear array

• Operates in the 2.4 GHz and 5 GHz frequency bands

• Gain:

–

2400–2483 MHz — 4-dBi

–

5250–5875 MHz — 7-dBi

The antenna is designed to create an omnidirectional broadcast pattern. To achieve this pattern, mount the access point clear of any obstructions to the sides of the radiating element.

Chapter 2 Installing the Access Point

For detailed information on this antenna, refer to the Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) document. Follow all safety precautions when installing the

antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on

page 2-29.

2-30

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 63

Chapter 2 Installing the Access Point

Figure 2-16 Cisco Aironet Dual-Band Omnidirectional Antenna - Installed Only on Model

Installing Antennas

AIR-CAP1532E-x-K9

1 Antenna connected to antenna port 1(Type-N

2 Antenna connected to antenna port 2(Type-N

connector) (TX/RX)

Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N)

The Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in both the 2.4-GHz and 5-GHz frequency bands. This antenna has 8-dBi gain in both bands.

For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

connector) (TX/RX)

2-31

Page 64

Installing Antennas

Chapter 2 Installing the Access Point

Figure 2-17 Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna - Installed Only on Model

AIR-CAP1532E-x-K9

334574

2-32

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 65

Chapter 2 Installing the Access Point

334576

Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N)

The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band.

This antenna can be installed using the optional directional-antenna mounting kit AIR-CCAMK-1, which allows the antenna to be mounted on the access point and positioned in multiple configurations. For more information, refer to Installing Directional-Antenna Mounting Kits on Cisco 1550 Series Outdoor Mesh Access Points.

For detailed information on this antenna, refer to the Cisco Aironet 5-GHz 14-dBi Directional Antenna (AIR-ANT5114P2M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Figure 2-18 Cisco Aironet 5-GHz 14-dBi Directional Antenna - Installed Only on Models

AIR-CAP1532E-x-K9

Installing Antennas

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-33

Page 66

Installing Antennas

334576

Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N)

The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band.

For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz 13-dBi Directional Antenna (AIR-ANT2413P2M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Figure 2-19 Cisco Aironet 2.4-GHz 13-dBi Directional Antenna - Installed Only on Models

AIR-CAP1532E-x-K9

Chapter 2 Installing the Access Point

2-34

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 67

Chapter 2 Installing the Access Point

231297

Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N)

The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band.

For detailed information on this antenna, refer to the document Cisco Aironet 5-dBI Omnidirectional Antenna (AIR-ANT2450V-N). Follow all safety precautions when installing the antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Figure 2-20 Cisco Aironet 2.4-GHz 5-dBi Omni Antenna - Installed Only on Model

AIR-CAP1532E-x-K9

Installing Antennas

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-35

Page 68

Installing Antennas

230540

Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N)

The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band.

For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N). Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Figure 2-21 Cisco Aironet 2.4-GHz 8-dBi Omni Antenna - Installed Only on Model

AIR-CAP1532E-x-K9i

Chapter 2 Installing the Access Point

2-36

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Page 69

Chapter 2 Installing the Access Point

Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N)

The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 8-dBi gain in the 5-GHz frequency band.

For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N). Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-29.

Figure 2-22 Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna - Installed Only on Model

AIR-CAP1532E-x-K9

Installing Antennas

OL-30864-01

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

2-37

Cisco Aironet 1530 Series, 1532 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Objectives

Preface

Audience

Organization

Conventions

Related Documents

Finding the Product Serial Number

Obtaining Documentation, Support, and Security Guidelines

Overview

About the 1532 Access Point

Hardware Models

Regulatory Domains

Hardware Features

Connectors

1532I/1532E Connectors

1532I/E Connectors

Antenna Port Locations

Radio Operation

AP1532I (Internal Antenna)

AP1532E (External Antenna)

Multiple Power Sources

Power injectors

Ethernet (PoE) Ports

Optional Hardware

Network Deployment Examples

Wireless Backhaul

Point-to-Point Bridging

Point-to-Multipoint Bridging

Point-to-Multipoint Mesh Network

Layer 3 Network Operation

Installing the Access Point

Unpacking the Access Point

Package Contents

Tools and Hardware

Optional Tools and Hardware

Optional Tools and Hardware That You Supply

Warnings

Safety Information

FCC Safety Compliance Statement

Safety Precautions

Avoiding Damage to Radios in a Testing Environment

Installation Guidelines

Site Surveys

Before Beginning the Installation

Becoming Familiar with Access Point Installation Components

Mounting the Access Point

Installation Options

Access Point Mounting Orientation

Wall Mounting the Access Point with the Fixed Mounting Kit

Pole Mounting the Access Point with the Fixed Mount Kit

Wall Mounting the Access Point with the Pivoting Mounting Kit

Pole Mounting the Access Point with the Pivoting Mounting Kit

Horizontally Mounting the Access Point with Optional Horizontal Mount Plate

Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=)

Installing Antennas

Non-Cisco Antennas

Safety Precautions when Installing Antennas

Antenna Configurations

Integrated Antenna Option

External Antenna Mounting Configurations