CHAUVET DJ Scorpion Storm FXRG User Manual

LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
CLASSIFIED PER EN/IEC 60825-1:2007
Complies with FDA performance standards for
laser products except for deviations pursuant to
Laser Notice No. 50, dated June
24, 2007.
Table of Contents
1. BEFORE YOU BEGIN ............................................................................................................................................................ 3
WHAT IS INCLUDED ....................................................................................................................................................... 3
CLAIMS ........................................................................................................................................................................ 3
MANUAL CONVENTIONS................................................................................................................................................. 3
SYMBOLS ..................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .................................................................................................................................................. 4
NON INTERLOCKED HOUSING WARNING .......................................................................................................................... 5
LASER SAFETY NOTES .................................................................................................................................................. 5
LASER SAFETY LABEL REPRODUCTION ............................................................................................................................ 6
LASER EMISSION DATA .................................................................................................................................................. 7
LASER COMPLIANCE STATEMENT ................................................................................................................................... 7
2. INTRODUCTION .............................................................................................................................................................. 8
PRODUCT OVERVIEW .................................................................................................................................................... 8
PRODUCT DIMENSIONS .................................................................................................................................................. 8
3. SETUP ....................................................................................................................................................................... 10
AC POWER ................................................................................................................................................................ 10
FUSE REPLACEMENT ................................................................................................................................................... 10
MOUNTING ................................................................................................................................................................. 10
Orientation 10 Rigging 10
PROPER USAGE .......................................................................................................................................................... 10
DATA LINKING ............................................................................................................................................................. 12
MASTER/SLAVE LINKING .............................................................................................................................................. 12
4. OPERATING INSTRUCTIONS .......................................................................................................................................... 13
NAVIGATING THE CONTROL PANEL ................................................................................................................................ 13
Menu Functions 13
DMX CHANNEL SUMMARY ........................................................................................................................................... 13
DMX CHANNEL VALUES .............................................................................................................................................. 14
TROUBLESHOOTING..................................................................................................................................................... 15
RETURNS ................................................................................................................................................................... 16
CONTACT US .................................................................................................................................................................. 16
TECHNICAL SPECIFICATIONS ........................................................................................................................................ 17
Scorpion™ Storm FXRG User Manual 2 Rev. 3
1. BEFORE YOU BEGIN
What Is Included
One User Manual
Claims
may invalidate your claim with the carrier. In addition, retain the container and all the packing
Manual Conventions
information from the regular text.
Convention
Meaning
<Menu>
A key to be pressed on the product’s control panel
1~512
A range of values
A menu option not to be modified (for example, showing the
Settings
ON
A value to be entered or selected
Symbols
Icons
M
Critical installation, configuration, or operation information. Important installation or configuration information. Failure to
One Scorpion™ Storm FXRG
One Power Cord
One Warranty Card
Immediately upon receipt, carefully unpack this product and check the container to make
sure you have received all the parts indicated above in good condition. If the container or the material inside the container (this product and any other accessory included) appears damaged from shipping, or shows signs of mishandling, notify the carrier immediately, not CHAUVET®, upon receipt of the damaged merchandise. Failure to do s o in a timely manner
material for inspection. For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with CHAUVET® within 7 days of receiving the merchandise.
CHAUVET® manuals use the following conventions to differentiate certain types of
50/60 A set of values of which only one can be chosen
Settings MENU >
operating mode/current statu s) A sequence of menu options to be followed
EANING
Failure to comply with this information may render the product partially or completely inoperative, cause damage to the product or cause harm to the user.
comply with this information may prevent the product from functioning correctly.
Useful information.
Scorpion™ Storm FXRG User Manual 3 Rev. 3
information about the installation, usage, and maintenance of this product.
Safety Instructions
Please read the following notes carefully because they include important safety
Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document.
Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on the decal or rear panel of the product.
This product is for indoor use only! To prevent risk of fire or shock , do not expose this product to rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect this product from the power source before cleaning it or replacing fuse.
Make sure to replace the fuse with another of the same type and rating.
If mounting it overhead, always secure this product to a fastening device using a
safety chain.
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this product at higher temperatures.
In the event of a serious operating problem, stop using the unit im mediately. Never try to repair the unit. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center.
Never connect this product to a dimmer pack or rheostat.
Make sure the power cord is not crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry a product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
Always avoid direct eye exposure to the light source when this product is on.
Lasers can be hazardous and have unique safety considerations. Permanent eye
injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in this user manual. Read all instructions carefully BEFORE operating this device.
Avoid direct eye contact with laser light. Never intentionally expose your eyes or
others to direct laser light.
This laser product can potentiall y cause instant eye injury or blindness if laser
light directly strikes the eyes.
It is illegal and dangerous to shine this laser into audience area s, wher e the
audience or other personnel could get direct laser beams or bright reflections into their eyes.
It is a U.S. federal offense to shine any laser at aircraft.
Use of controls or adjustments or performance of procedures other than those
specified herein may re sult in hazardous radiation exposure.
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service, please contact the dealer nearest to you.
Scorpion™ Storm FXRG User Manual 4 Rev. 3
This unit contains high-power laser devices internally.
burns, and fires.
sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it
It is incorrect to think that because these laser entertainment products split the laser into
for eye exposure. This laser product uses dozens of milliwatts of laser
power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many
assume that because the laser light is moving, it is safe. This is not true.
Nor, do the laser beams always move. Since eye injuries can occur instantly, it is critical to to aim Class 3R lasers in areas which people can get exposed. This is true even if it is aimed
Always use appropriate lighting safety cables when hanging lights and effects overhead.
Non Interlocked Housing Warning
Do not open the laser housing because of potential exposure to unsafe levels of laser radiation.
The laser power levels, accessible if the unit is opened, can cause instant blindness, skin
Laser Safety Notes
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser light is different from any other light s ources with which you may be familiar. The light from this product can potentially cause eye injury if not set up and used properly. Laser light is thousands of times more concentrated than light from any other kind of light source. This concentration of light can cause instant eye injuries, primarily by burning the retina (the light
can still potentially injure or blind you or your audience. Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries can happen quicker than you can blink.
hundreds of beams and the laser beams are scanned out in high speed, that an individual laser beam is safe
of the individual beams are potentially hazardous to the eyes. It is also incorrect to
prevent the possibility of any direct eye exposure. In the laser safety regulation, it is not legal below people’s faces, such as on a dance floor.
Do not operate the laser without first reading and understanding all safety and technical data in this manual.
Always set up and install all laser effects so that all laser light is at least three (3) meters (9.8 feet) above the floor on which people can stand. See “Proper Usage” section later in this manual.
After set up, and prior to public use, test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels above Class 3R.
Do not use laser if the laser appears to be emitting only one or two beams.
Do not point lasers at people or animals.
Never look into the laser aperture or laser beams.
Do not point lasers in areas in which people can potentially get exposed, such as
uncontrolled balconies, etc.
Do not point lasers at highly reflective surfaces, such as windows, mirrors, and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft; this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use the laser if the housing is damaged, open, or if the optics appear damaged in
any way.
Never open the laser housing. The high laser power levels inside the protective housing can start fires, burn skin, and will caus e instant eye injury.
Never leave this device running unattended.
The operation of a Class 3R laser show is only allowed if the show is controlled by a
skilled and well-trained operator, familiar with the data included in this manual.
The legal requirements for using laser entertainment products vary from country to country. The user is responsible for the legal requirements at the location/country of use.
Scorpion™ Storm FXRG User Manual 5 Rev. 3
LASER HAZARD
WARNING LABEL
LASER APERTURE LABEL
EXPLANATORY, CERTIFICATION LABEL
NON INTERLOCKED
Laser Safety Label Reproduction
MANUFACTURER’S ID, &
HOUSING LABEL
Scorpion™ Storm FXRG User Manual 6 Rev. 3
Further guidelines and safety programs for safe use of lasers can be found in the ANSI
he guidelines of ANSI Z136.1. Laser
Display guidance can be obtained via the International Laser Display Association:
This laser product complies with EN/IEC 60825-1 Ed 2, 2007-03, and US FDA/CDRH
standards.
Laser light - Avoid direct eye contact!
Z136.1 Standard “For Safe Use of Lasers,” available from the Laser Institute of America:
www.laserinstitute.org. Many local governments, corporations, agencies, military,
and others, require all lasers to be used under t
www.laserist.org.
Laser Emission Data
LASER CLASSIFICATION CLASS 3R
Green Laser Medium DPSS Nd:YVO4, 532 nm
Red Laser Medium LD GaAlAs 650 nm, typical
Beam Diameter <5mm at aperture
Pulse Data All pulses < 4 Hz (>0.25 sec)
Divergence (each beam) <2 mrad
Divergence (total light) <160 degrees
Laser Power of Each Beam from Aperture*
* As measured under IEC measurement conditions for classification.
Laser Compliance Stateme nt
FLPPS via the terms of Laser Notice No. 50 dated June 24, 2007. This laser device is classified 3R. (Class 3R is the international equivalent of U.S. Class IIIa). No maintenance is required to keep this product in compliance with laser performance
<5
MW
Scorpion™ Storm FXRG User Manual 7 Rev. 3
Power LED
Hanging bracket
Bracket Audio LED
Laser Aperture
2. INTRODUCTION
Product Overview
adjustment knob (1 of 2)
Scorpion™ Storm FXRG User Manual 8 Rev. 3
Product Dimensions
Scorpion™ Storm FXRG User Manual 9 Rev. 3
The fuse is located
flat-head screwdriver.
Hanging Clamp
Note! Clamp is sold separately.
Always connect the product to a switched circuit. Never connect the product to a rheostat
to 100% switch.
type of fuse.
This product is for overhead
For safety
recommends mounting your
3. SETUP
AC Po we r
This fixture has an auto-switching power supply that can accommodate a wide range of input voltages. Before poweri ng on the unit, make sure the line voltage you are applying is within the range of accepted voltages . This fixture will accommodate 100~240 VAC, 50/60 Hz.
(variable resistor) or dimmer circuit, even if the rheostat or dim m er channel is used only as a 0%
Fuse Replacement
With a flat-head screwdriver, wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type of fuse. Insert the fuse holder back in its place and reconnect
Disconnect the power cord before replacing a fuse and always replace with the same
power.
Mounting
Orientation
This fixture may be mounted in any safe position, provided there is adequate room for venti lation.
Rigging
It is important never to obstruct the fan or vents pathway. Mount the fixture using a suitable C- or O-type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. Once the fixture is in the desired position, retighten both knobs.
inside this compartment. Remove using a
When selecting installation location, take into consideration access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to
rain, high humidity, extreme temperature changes, or restricted ventilation.
Proper Usage
mounting only. purposes, CHAUVET®
Scorpion™ Storm FXRG User Manual 10 Rev. 3
lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety
You can obtain
appropriate mounting hardware
International laser safety
n the
fashion illustrated below, with a
meters (9.8
t) of vertical separation between the floor and the lowest laser light vertically . Additionally,
meters of horizontal
separation is required between
nce or other
public spaces.
cables. from your lighting ve ndor.
regulations require that laser products must be operated i
minimum of three (3) fee
three (3) laser light and audie
Scorpion™ Storm FXRG User Manual 11 Rev. 3
Master
Slave
Slave
Often, the setup for Master/Slave or
a DMX optically isolated splitter may result in deterioration of the digital DMX signal.
CAUTION: Use of controls, adjustments, or performance of
CAUTION PERFORMANCE OF PROCE SPECIFIED HAZARDOUS RADIATION
Data Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a Master/Slave operating mode. The combined number of channels required by all the fixtures on a s erial data link determines the number of fixtures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard, no more than thirty-two (32) fixtures should be connected on one data link. Connecting more than thirty-two (32) fixtures on one serial data link without the use of
Master/Slave Linking
1. Connect the (male) 3-pin connector side of the DMX cable to the output (female) 3-pin connector of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3-pin connector to the input connector of the next fixture consisting of a (male) 3-pin connector. Then, proceed to connect from the output to the input of the following fixture and so on (see above).
— USE OF CONTROLS OR ADJUSTMENTS, OR
DURES OTHER THAN THO SE
IN THIS USER MANUAL MAY RESULT IN
EXPOSURE
standalone operations require that the first fixture in the chain be initialized via DIP switches. Secondarily, the fixtures that follow may also require a slave setting. Please consult the Operating
Instructions section of this manual for
complete instructions for this type of setup and configuration.
Scorpion™ Storm FXRG User Manual 12 Rev. 3
procedures other than what is specified herein may result in hazardous radiation exposure
MAIN FUNCTION
SELECTION
DESCRIPTION/VALUES
DMX mode
001
001-506
DMX starting address assignment
AFr
Automatic fast (red)
ASr
Automatic slow (red)
AFG
Automatic fast (green)
ASG
Automatic slow (green)
AFB
Automatic fast (red & green)
ASB
Automatic slow (red & green)
SrD
Sound (red)
SGr
Sound (green)
SrG
Sound (red & green)
rDM
Random
Slave
SLA
Slave mode
CHANNEL
FUNCTION
1
2
3
4
5
6
7
Button
Function
Used to access the menu or to return to a
Scrolls through menu options in ascending
Scrolls through menu options in descending
Used to select and store the current menu
MENU
UP
DOWN
ENT
4. OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LED Display.
<MENU>
<UP>
<DOWN>
<ENT>
The Control Panel LED Display shows the menu items you select from the menu map below. When a menu function is selected, the display will show immediately the first available option for the selected menu function. To select a menu item, press <ENT>. Use <UP> and <DOWN> to navigate the menu map and menu options. Press <ENT> to access the menu function currently displayed or to enable a menu option. To return to the previous option or menu without changing the value, press <MENU>.
previous menu option
order
order
or option within a menu
Menu Functions
Standalone modes
DMX Channel Summary
Control mode Color selection Strobe
Scorpion™ Storm FXRG User Manual 13 Rev. 3
Rotation (motor 1) Stutter (motor 1) Rotation (motor 2) Stutter (motor 2)
CHANNEL
VALUE
FUNCTION
200 255
Control Mode
Random
255  255
Strobe
Strobe to sound
134 255
Rotation (motor 1)
Counterclockwise rotation (slow  fast)
167 255
Stutter (motor 1)
Mode 4 (slow  fast)
134 255
Rotation (motor 2)
Counterclockwise rotation (slow  fast)
169  255
Stutter (motor 2)
Mode 4 (slow  fast)
DMX Channel Values
1
2
3
4
000 019 020 039 040 059 060 079 080 099 100 119 120 139 140 159 160 179 180 199
000 004 005 028 029 056 057 084 085 112 113 140 141 168 169 197 198 224 225 255
000 004 005 254
000 004 005 127 128 133
DMX Mode Automatic fast (red) Automatic slow (red) Automatic fast (green) Automatic slow (green) Automatic fast (red & green) Automatic slow (red & green) Sound (red) Sound (green) Sound (red & green)
Color selection
Blackout Red Green Red & Green Green strobing Red strobing Red on & Green strobing Green on & Red strobing Red & Green strobing Red & green (alternate strobing)
No function Strobe (slow  fast)
No rotation Clockwise rotation (slow  fast) Stop
000 004 005 056
5
057 112 113 168
000 004
6
005 127 128 133
000 004 005 056
7
057 112 113 168
No function Mode 1 (slow  fast) (affected by channel 4) Mode 2 (slow  fast) (affected by channel 4) Mode 3 (slow  fast)
No rotation Clockwise rotation (slow  fast) Stop
No function Mode 1 (slow  fast) (affected by channel 6) Mode 2 (slow  fast) (affected by channel 6) Mode 3 (slow  fast)
Scorpion™ Storm FXRG User Manual 14 Rev. 3
Applies to
Lights
Controllers
Auto shut off
Check fan thermal switch reset
Beam is very dim or not bright
Clean optical system or replace lamp Check 220/110 v switch for proper setting
Breaker/Fuse keeps blowing
Check total load placed on device
Device has no power
Check for power on Mains Check device’s fuse (internal and/or external)
Fixture is not
Check DMX Dip switch settings for correct addressing Check polarity switch settings
Fixture is on but
audio
Make sure you have the correct audio mode on the
Adjust sound sensitivity knob
Lamps cuts off sporadically
Possible bad lamp or fixture is overheating Lamp may be at end of its life
Light will not come
Some discharge lamps require a cooling off period again, wait 5 to 10 minutes before powering up
Loss of signal
Use only DMX cables
or black lights.
Moves slow
Check 220/110v switch for proper setting
No flash
Re-install bulb, may have shifted in shipping
No laser output
Bounce mirror motor may have shifted during shipping, readjust
Standalone mode
All Chauvet® lighting fixtures featuring standalone
Troubleshooting
Symptom Solution(s)
responding
there is no movement to the
on after power failure
Check DMX cables
control switches. If audio provided via ¼″ jack, make sure a live audio signal exists
before the electronics in the fixture can kick start it
Install terminator Note: Keep DMX cables separated from power cables
functions do not require additional setting s, si mply power the fixture on and it will automatically enter into this mode
If you still have a problem after trying the above solutions, please contact CHAUVET® Technical Support.
Scorpion™ Storm FXRG User Manual 15 Rev. 3
World Headquarters
United Kingdom & Ireland
CHAUVET®
CHAUVET® Europe Ltd.
Email: tech@chauvetlighting.com
World Wide Web: www.chauvetlighting.com
World Wide Web: www.chauvetlighting.co.uk
Returns
Returned merchandise must be sent prepaid and in the original packing. CHAUVET® will not issue call tags. Package must be clearly labeled with a Return Merchandise Authorization (RMA) number). Products returned without an RMA number will not be accepted.
Call CHAUVET® and request an RMA number prior to shipping the fixture. Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return.
Mark the RMA number clearly on a label and apply to the box. Do not write the RMA number directly on the box.
Be sure to properly pack the fixture and accessories. Any shipping damage resulting from inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own discretion to repair or replace product(s ). FedEx packing or double-boxing are recommended.
If you are given an RMA number, please include the following information on a piece of paper inside the box:
Your name
Your address
Your phone number
The RMA number
Contact Us
General Information
Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: 954-929-1115 Fax: 954-929-5560 Toll free: (800) 762-1084
Technical Support
Voice: 954-929-1115 (Press 4) Fax: 954-756-8015
A brief description of the cause(s) for the return
General Information
Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT
Voice: +44 (0)1773 511115
Fax: +44 (0)1773 511110
Technical Support
Email: uktech@chauvetlighting.com
Scorpion™ Storm FXRG User Manual 16 Rev. 3
Technical Specifications
WEIGHT & DIMENSIONS
Length ..................................................................................................................................................................... 10.8 in (276 mm)
Width ............................................................................................................................................................................ 9 in (229 mm)
Height ........................................................................................................................................................................ 9.2 in (234 mm)
Weight ........................................................................................................................................................................ 5.9 lbs (2.7 kg)
POWER
Autoswitching .............................................................................................................................................. 100~240 VAC, 50/60 Hz
Fuse ............................................................................................................................................................................... T 1 A, 250 V
Power Consumption @ 120 V ............................................................................................................................................. 0.3 A max
Power Linking @ 120 V ......................................................................................................................................................... 28 units
Power Consumption @ 230 V ............................................................................................................................................. 0.2 A max
Power Linking @ 230 V ......................................................................................................................................................... 50 units
LASER
Green diode ............................................................................................................................................................... 532 nm, 40 mW
Red Diode ............................................................................................................................................................... 650 nm, 100 mW
Laser Type ............................................................................................................................................................................... DPSS
RANGE
Coverage Angle ............................................................................................................................................................................ 99°
THERMAL
Maximum ambient temperature ................................................................................................................................... 104° F (40° C)
Cooling ............................................................................................................................................................................. Fan cooled
CONTROL & PROGRAMMING
Data input ........................................................................................................................................... locking 3-pin XLR male socket
Data output .................................................................................................................................................. 3-pin XLR fem al e socket
Data pin configuration ....................................................................................................................... pin 1 (shield), pin 2 (-), pin 3 (+)
Protocols ............................................................................................................................................................... USITT DMX512-A
DMX Channels ................................................................................................................................................................................ 7
ORDERING INFORMATION
Scorpion™ Storm FXRG........................................................................................................................... SCORPIONSTORMFXRG
WARRANTY INFORMATION
Warranty ......................................................................................................................................................... 2-year lim i t ed warranty
Scorpion™ Storm FXRG User Manual 17 Rev. 3
Loading...