Chauvet DJ Obsession HP LED Lichteffekt User Manual [EN]

OBSESSION HP
User Manual
Table of Contents
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 1
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims ........................................................................................................... 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Safety Notes.................................................................................................. 2
2. Introduction ................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions ...................................................................................... 3
3. Setup ........................................................................................... 4
AC Power...................................................................................................... 4
Mounting ....................................................................................................... 5
Gobos............................................................................................................ 6
4. Operation .................................................................................... 7
Control Panel Operation................................................................................ 7
Menu Map ..................................................................................................... 7
Configuration (DMX) ..................................................................................... 7
DMX Values .................................................................................................. 8
Configuration (Standalone) ........................................................................... 9
Master/Slave Mode ....................................................................................... 9
IRC-6 Infrared Remote Control ..................................................................... 10
IRC-6 Operation ................................................................................................. 10
5. Maintenance................................................................................ 11
Product Maintenance .................................................................................... 11
6. Technical Specifications ........................................................... 12
7. Returns........................................................................................ 13
8. Contact Us .................................................................................. 14
Obsession HP User Manual Rev. 2
Before You Begin
1. Before You Begin
What Is Included
Obsession HP
•Power cord
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
Quick Reference Guide
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
Important installation or configuration information. The product may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision; however, Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest version from www.chauvetdj.com
The works of authorship contained in this manual, including, but not limited to, all designs, texts, and images are owned by Chauvet.
© Copyright 2021 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
.
CHAUVET, the Chauvet logo, and Obsession HP are registered trademarks or trademarks of Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.
Obsession HP User Manual Rev. 2
Page 1 of 18
Safety Notes
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Always disconnect the product from the power source before cleaning or replacing the fuse.
Avoid direct eye exposure to the light source while the product is on.
Make sure the power cord is not crimped or damaged.
Never disconnect the product from power cord by pulling or tugging on the cord.
If mounting the product overhead, always secure to a fastening device using a safety cable.
Make sure there are no flammable materials close to the product when operating.
Do not touch the product’s housing when operating because it may be very hot.
Do not charge the battery of the product in a closed case or container.
Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product.
The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.
Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are blocked.
Never connect the product to a dimmer.
Make sure to replace the fuse with another of the same type and rating.
Never carry the product from the power cord or any moving part. Always use the hanging/ mounting bracket.
The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher temperatures.
In the event of a serious operating problem, stop using the product immediately.
Never try to repair the product. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Before You Begin
Keep this User Manual for future use. If you sell the product to someone else, be sure that they also receive this document.
Page 2 of 18
Obsession HP User Manual Rev. 2
Introduction
Mounting bracket
Display screen
Infrared sensor
Power in/out
3-pin
DMX in/out
Menu buttons
Bracket
adjustment
knobs (2x)
Fan
Easy-access gobo door
15 in
380 mm
12 in
305 mm
8.26 in
210 mm
2. Introduction
Product Overview
Product Dimensions
Obsession HP User Manual Rev. 2
Page 3 of 18
Setup
Installed fuse
(held by plastic clip)
Safety cap
Spare fuse holder
(inside safety cap)
Additional products
1st product
2nd product
3rd product
3. Setup
AC Power
This product has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz.
To eliminate unnecessary wear and improve its lifespan, completely disconnect the product from power via breaker or by unplugging it during periods of non-use.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse replacement
1. Disconnect the product from power.
2. Wedge the tip of a flathead screwdriver into the slot of the fuse holder.
3. Pry the safety cap out of the housing.
4. Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the exact same type and rating.
5. Re-insert the fuse holder and reconnect power.
Power Linking
The product provides power linking via the Edison outlet located in the back of the product. Please see the diagram below for further explanation. Power-linking cords can be purchased separately from Chauvet.
Page 4 of 18
Disconnect the product from the power outlet before replacing the fuse.
It is possible to link up to 3 Obsession HP products on 120 VAC or up to 6 products on 230 VAC. Never exceed this number.
The power-linking diagram corresponds to the North American version of the product ONLY! If using the product in other markets, consult with the local Chauvet distributor, as power-linking connectors and requirements may differ in per country and region.
Obsession HP User Manual Rev. 2
Setup
Mounting clamp
Safety cable
Mounting
bracket
Floor Mounting
Overhead Mounting
Easy-access
gobo door
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The Obsession HP may be mounted in any position; however, make sure adequate ventilation is provided around the product.
Rigging
Before deciding on a location, always make sure there is easy access to the product for maintenance and programming purposes.
Make sure adequate ventilation is provided around the product.
Make sure that the structure or surface onto which you are mounting the product can support the product’s weight. (see the Technical Specifications
When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, such as an elevated platform or a truss.
When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
When power linking multiple products, mount the products close enough for power-linking cables to reach.
The bracket adjustment knob allows for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knob manually. Using tools could damage the knob.
Mounting Diagram
)
Obsession HP User Manual Rev. 2
Page 5 of 18
Gobos
1
2
3
4
5
6
7
Setup
Replacing Gobos
The gobos in the Obsession HP can quickly be changed using the easy-access gobo door located on top of the fixture. To remove and replace the gobos in Obsession HP, do the following:
1. Loosen the two screws holding the easy-access gobo door. Remove it to gain access to the gobo
wheel.
2. Gently pry the individual gobo holder by pushing and sliding it away from the gobo wheel. Do this
with all the gobos that need to be removed.
3. To replace a gobo, carefully slide the individual gobo holder into a slot in the gobo wheel. Make
sure that the two prongs in the gobo holder align with the two holes in the gobo wheel. Gently press the gobo holder into the gobo wheel until it clicks in place.
4. Replace the easy-access door and tighten the two screws to hold it in place.
Page 6 of 18
Obsession HP User Manual Rev. 2
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview
Button Function
<MENU> Exits from the current menu or function
<UP> Navigates upwards through the menu list and increases the numeric value when in a function
<DOWN>
<ENTER>
Navigates downwards through the menu list and decreases the numeric value when in a function
Enables the currently displayed menu or sets the currently selected value into the selected function
Menu Map
Refer to the Obsession HP product page on www.chauvetdj.com for the latest menu map.
Mode Programming Levels Description
Address
Auto programs P-- auto Auto programs
Auto speed S-- 001–100 Auto programs speed
Sound-active
mode
Sound sensitivity SENV 001–100 Adjusts sound sensitivity
Infrared mode SET
Master/Slave
mode
Motor
to see the button locations on the control panel.
2Ch 8Ch
Snd
SLV
mot
Gobo
d001–512 Sets the DMX personality
BO Blackout when no sound
SLOW Rotate slow when no sound
on
off SLV1 Copies the master unit SLV2 Slave unit for coordinated show
000–100
Turns infrared on or off
Overrides mirror dish rotation speed for auto/ sound only. If this is set to 000, this setting has no effect on anything. When set to 050, the mirror dish or gobo will rotate at 50% speed, and the auto or sound program speed control will adjust the colors and gobos only.
Configuration (DMX)
The Obsession HP works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website:
https://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf
DMX Personality and Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, the access to some of the product’s channels might get restricted.
The Obsession HP uses up to 8 DMX channels in an 8CH DMX mode, which defines the highest configurable address to 505.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 2Ch or 8Ch shows on the display.
2. Press <ENTER>, then d001–512 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Obsession HP User Manual Rev. 2
.
Page 7 of 18
DMX Values
2Ch 8Ch Function Value Percent/Setting
000 No function
1 1 Auto programs
Auto speed 000 255
22
Sound sensitivity 000 255
3 Dimmer 000 255 0–100%
–4Shutter
5 Color wheel
–6
7 Gobo rotation
8 Mirror rotation
Gobo wheel
(see Gobos)
001 127 Auto mode 128 255 Sound mode
Slow to fast (activates when Channel 1 is on auto mode)
0–100% (activates when Channel 1 is on sound mode)
000 015 Open 016 255 Strobe speed, slow to fast 001 009 White 010 019 Red 020 029 Green 030 039 Blue 040 049 Yellow 050 059 Amber 060 069 Magenta 070 079 Magenta + white 080 089 Magenta + amber 090 099 Amber + yellow 100 109 Yellow + blue
110 119 Blue + green 120 129 Green + red 130 139 Red + white 140 197 Clockwise scroll, fast to slow 198 255 Counterclockwise scroll, slow to fast 001 019 Gobo 1 020 039 Gobo 2 040 059 Gobo 3 060 079 Gobo 4 080 099 Gobo 5
100 119 Gobo 6 120 139 Gobo 7 140 197 Gobo clockwise scroll, fast to slow 198 255 Gobo counterclockwise scroll, slow to fast 001 042 Gobo indexing 043 086 Rotate counterclockwise, slow to fast 087 129 Stop 130 173 Rotate clockwise, slow to fast 174 217 Stop
218 255
001 086 Clockwise rotation, slow to fast 087 129 Stop 130 222 Counterclockwise rotation, slow to fast
223 255
Alternating clockwise-counterclockwise rotation, slow to fast
Alternating clockwise-counterclockwise rotation, slow to fast
Operation
Page 8 of 18
Obsession HP User Manual Rev. 2
Operation
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.
Automatic Programs
To run the Obsession HP in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly to select P-- from the menu list.
2. Press <ENTER>.
3. Select <auto>.
4. Press <ENTER>.
Auto-Program Speed
To change the auto-program speed on the Obsession HP, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to increase or decrease the program speed, from (S 1–100).
4. Press <ENTER>. The product will return to the last selected mode.
Sound-Active Mode
To run the Obsession HP in sound-active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select between BO (blackout when no sound) and SLOW (rotate
slowly when no sound).
4. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Master/Slave Mode
The Master/Slave mode allows a single Obsession HP product (the “master”) to control the actions of one or more Obsession HP products (the “slaves”) without the need of a DMX controller or DMX cables. The master (transmitter) product should be set to operate in either standalone mode or with the IRC-6, whereas the slave (receiver) products should be set to operate in Slave mode. Once set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below:
Slave products
1. Press <MENU> repeatedly until SLV shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select from SLV1 or SLV2.
•Select SLV1 for the first slave unit to copy the master unit
•Select SLV2 for the subsequent units
4. Press <ENTER>.
5. Connect the DMX input of the first slave product to the DMX output of the master product.
6. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave product.
7. Finish setting and connecting all the slave products.
Master product
1. Set the master product to operate in standalone mode or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
Configure all the slave products before connecting the master to the daisy chain.
Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master.
Obsession HP User Manual Rev. 2
Page 9 of 18
Operation
BLACK
OUT
AUTO
SOUND
SENSI­TIVITY
SPEEDSTROBE
%
MANUAL
FADE
RGB
WUVA
+ 0
-
123
654
789
IRC-6 Infrared Remote Control
The Obsession HP is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR mode, follow the instructions below:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> to select on or off.
4. Press <ENTER>.
IRC-6 Operation
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product. To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed of the auto programs.
Sound Mode
To select Sound mode:
1. Press <SOUND> on the IRC-6.
2. Press <+> or <–> to choose between the different sound programs.
To adjust the sound sensitivity:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sound sensitivity.
Strobe
To adjust the strobe rate:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
Dimmer
To adjust the total output with the IRC-6:
1. Press <%> on the IRC-6.
2. Press <+> or <–> to increase or decrease the output level.
Black Out
To black out the lights:
1. Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again. NOTE: The IRC-6 will not respond to any inputs when Black Out is activated. If the remote does not respond when a button is pressed, try pressing <BLACK OUT>. You may have inadvertently activated Black Out.
Page 10 of 18
Obsession HP User Manual Rev. 2
Maintenance
5. Maintenance
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
Obsession HP User Manual Rev. 2
Page 11 of 18
Technical Specifications
6. Technical Specifications
Dimensions and Weight
Length Width Height Weight
15 in (380 mm) 8.26 in (210 mm) 12 in (305 mm) 10.2 lb (4.7 kg)
Note: Dimensions in inches rounded to the nearest decimal digit. Power
Power Supply Type Range Voltage Selection
Switching (external) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 230 V, 50 Hz
Consumption 176 W 171 W
Operating current 2.2 A 1.3 A
Power linking 3 units 6 units
Power I/O U.S./Worldwide UK/Europe
Power input connector IEC IEC
Power cord plug Edison (U.S.) Local plug
Light Source
Type Color Quantity Power Current Lifespan
LED Cool white 1 100 W 4 A 50,000 hours
Photometrics
Strobe Rate Beam Angle
0–20Hz 116°
Thermal
Maximum External Temperature Cooling System
104 °F (40 °C) Convection
DMX
I/O Connector Channel Range
3-pin XLR 2 or 8 channels
Ordering
Product Name Item Code UPC Number
Obsession HP 07051800 781462221485
Page 12 of 18
Obsession HP User Manual Rev. 2
Returns
Returns
To get support or return a product:
If you are located in the U.S., contact Chauvet World Headquarters.
If you are located in the U.K. or Ireland, contact Chauvet Europe Ltd.
If you are located in Benelux, contact Chauvet Europe BVBA.
If you are located in France, contact Chauvet France.
If you are located in Germany, contact Chauvet Germany.
If you are located in Mexico, contact Chauvet Mexico.
If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See www.chauvetdj.com France, Germany, or Mexico.
If you are located outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact your distributor of record and follow their instructions on how to return Chauvet products to them. Visit our website www.chauvetdj.com
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags. Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA
number.
for distributors outside the U.S., U.K., Ireland, Benelux,
for contact details.
.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.
Before sending the product, clearly write the following information on a piece of paper and place it inside the box:
Your name
Your address
Your phone number
RMA number
A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned product(s).
Obsession HP User Manual Rev. 2
Page 13 of 14
Contact Us
World Headquarters
UK
Benelux
France
Germany
Mexico
Address: Av. de las Partidas 34 - 3B
Lerma, Edo. de México, CP 52000
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetdj.com
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetdj.eu
NG16 6NT
Voice: + 44 (0) 17 7 3 511115
Fax : + 44 (0) 1 7 7 3 511110
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetdj.eu
Voice: +32 9 388 93 97
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France Website: www.chauvetdj.eu
Voice: +33 1 78 85 33 59
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany Website: www.chauvetdj.eu
Voice: +49 421 62 60 20
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetdj.mx
Voice: +52 (728) 690-2010
Email: FRtech@chauvetlighting.fr
Email: DEtech@chauvetlighting.de
Email: servicio@chauvet.com.mx
Contact Us
Visit the applicable website above to verify our contact information and instructions to request support. Outside U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the dealer of the record.
Page 14 of 14
Obsession HP User Manual Rev. 2
Loading...