KITCHEN T OPMOUNT FAUCET
6 Inch Centers
Cast Brass Body
Hose & Spray
6" Centers with Hose & Spray and Compression Stem Assemblies
0126 - A Series with 8-inch Swivel S pout
0128 - A Series with 8-inch D-S pout
Faucets with lever, wrist or elbow
handles and compression or ceramic
stem cartridges are ADA compliant.
Certified to
ANSI/NSF 61 Section9
CENTRAL BRASS MFG CO
2950 East 55th Street, Cleveland, Ohio 44127
Phone: 216-883-0220 Fax: 216-883-0875 Email: sales @CentralBrass.com
051203 I-0126
www.CentralBrass.com
CENTRAL BRASS
INSTALLATION INSTRUCTIONS
NOTE:
Faucets supplied
without hose and
spray should be
flushed with only the
aerator removed.
1. Remove locknut from hose guide and place through proper hole in sink. Re-assemble locknut
on shank and tighten.
2. Insert hose end of spray hose assembly down through hose guide then up through center faucet
hole in sink. Att ach to threads of nipple from the bottom center of the fixture body. Tighten by
hand to finger tight + 1/4 turn max. If need be, diverter assembly can be held through spout hole
with a 3/8 hex wrench while tightening hose. Ensure that diverter assembly does not back out and
break O-Ring seal.
3. Apply a thin coat of soft plumbers putty to the bottom edge of the faucet body , place the faucet
shanks thru the holes in the sink. (Handles indexed cold on right side, body marked on bottom front
for those without handle indexes.
4. Attach steel washer and locknuts and tighten. Connect hot water supply to left side and cold
water supply to right side. Tighten coupling nut s securely.
5. Remove aerator (if needed) from spout and install on to body . T urn on hot and cold water for
one minute to flush out dirt and sediment that might have accumulated in lines during installation.
Assembly aerator to spout.
7. T est spray rinse for proper operation and check all connections for leakage.
CENTRAL BRASS MFG CO
2950 East 55th Street, Cleveland, Ohio 44127
Phone: 216-883-0220 Fax: 216-883-0875 Email: sales @CentralBrass.com
051203 I-0126
www.CentralBrass.com
REPLACEMENT
1
*
PARTS
7
*
0126 Series
D
7
A
*
8
9
*
*
2
3
B
4
*
8
9
0128 Series
D
5
*
11
12
C
10
6
E
13
Certified to
ANSI/NSF 61 Section9
2950 East 55th Street, Cleveland, Ohio 44127
Phone: 216-883-0220 Fax: 216-883-0875 Email: sales @CentralBrass.com
* These items are not offered
individually and must be
purchased as a group or unit.
Please contact Central Brass
for more information.
CENTRAL BRASS MFG CO
Butterfly Style
Cartridge Style
G
F
H
G
H
F
*
051203 I-0126
www.CentralBrass.com
REPLACEMENT P ARTS
# Part # Description
A G-523-C Lever Handle C Indexed with Screw (X107-F)
A G-523-H Lever Handle H Indexed with Screw (X107-F)
B G-453-EL Cold O-Ring Stem Assembly with Gasket (X1028-Y)
B G-453-ER Hot O-Ring Stem Assembly with Gasket (X1028-Y)
C K-453-C Cold O-Ring Stem Assembly with Gasket (X1028-Y) and Seat (X263-BC)
C K-453-H Hot O-Ring Stem Assembly with Gasket (X1028-Y) and Seat (X263-BC)
D SU-363-RA 8-Inch Swivel Spout with Aerator (30-M) 0126 Series
D SU-365-CA 8-Inch Swivel D-Spout with Aerator (30-M) 0128 Series
E G-913-A Coupling Nut group (1 set)
F SU-266 Diverter Cartridge (for cartridge style)
F 166-DE Upper & Lower Diverter unit (for butterfly style)
G SU-2987-DA Guide for Hose & Spray
H 266-A Hose & Spray assembly (female connector for cartridge style)
H 166-A Hose & Spray assembly (male connector for butterfly style)
1 X 107- F Handle Screw (25 pcs per pack)
2 X1038-453 O-Rings (25 pcs per pack)
3 X901-WNN Stem Seat Washer (25 pcs per pack)
4 X104 Seat Washer Screw (25 pcs per pack)
5 X1028-Y Gasket (25 pcs per pack)
6 X263-BC Replacement Seat (10 pcs per pack)
7 30-M Aerator
8 X166-FN Snap Ring (6 pcs per pack)
9 X1038-KN Spout O-Ring (25 pcs per pack)
10 X54 Crowfoot Washer (10 pcs per pack)
11 X7133-AL Locknut (10 pcs per pack)
12 X4015 Coupling Nut (4 pcs per pack)
OPTIONS & REPLACEMENT PARTS for options
Suffix
Number
2 D SU-363-JA 10-Inch Swivel Spout with Aerator (30-M)
3 D SU-363-LA 12-Inch Swivel Spout with Aerator (30-M)
4 D SU-363-MA 14-Inch Swivel Spout with Aerator (30-M)
8 D SU-357-HSA 7 ¼ Inch High-Rise Swivel Spout with Aerator (30-L)
70 A K-506-1C or 1H Acrylic Handle with C or H metal indexed button
Replaces
Item #
Part Number Description
X126-625B Handle Screw for Acrylic Handles suffix’s 70 or 80 (6 pcs per pack)
G-503-M-02 Metal indexed buttons C & H for Acrylic Handles suffix’s 70 or 80 (one pair per pack)
If faucet has round handles (70 or 80 suffixes) , use two Hot stem assemblies
If faucet has lever handles, use one Hot and one Cold stem assemblies
CENTRAL BRASS MFG CO
2950 East 55th Street, Cleveland, Ohio 44127
Phone: 216-883-0220 Fax: 216-883-0875 Email: sales @CentralBrass.com
051203 I-0126
www.CentralBrass.com
CENTRAL BRASS
MAINTENANCE INSTRUCTIONS
1
2
3
DISASSEMBLY
REMOVE HANDLE
1. Turn of f water supply .
2. Remove screw.
3. Remove handle.
REMOVE STEM ASSEMBLY
1. Use adjustable
wrench.
2. Unscrew (counter-
Wrench
REMOVE SEA T
(For compression stems only)
clockwise) remove
stem unit.
REPLACEMENT
4
Use Only Genuine
Central Replacement Parts
Compression Units
G-453-ER Hot stem assembly
G-453-EL Cold stem assembly
X263-BC Replaceable Seat
Ceramic Units
K-352-H Ceramic Hot stem assembly
K-352-C Ceramic Cold stem assembly
1. Insert 5/16" allen
wrench in seat.
CERAMIC
2. Turn seat (counterclockwise) to remove.
If faucet has round handles (70 or 80 suffixes) , use two Hot stem assemblies
If faucet has lever handles, use one Hot and one Cold stem assemblies
COMPRESSION
CENTRAL BRASS MFG CO
2950 East 55th Street, Cleveland, Ohio 44127
Phone: 216-883-0220 Fax: 216-883-0875 Email: sales @CentralBrass.com
051203 I-0126
www.CentralBrass.com
Loading...