Instructions
for use
MILK FROTHER
MF
MILK FROTHER
CONTENTS
4 Congratulations
5 Catler recommends safety first
8 Know your Milk Frother MF 8010
12 Operating your Milk Frother MF 8010
13 Hints & tips
14 Care and Cleaning
16 Troubleshooting
17 Recipes
CONTENTS
3
3
Congratulations
on the purchase of your new Catler Milk Frother MF 8010.
44
CONGRATULATIONS
CATLER RECOMMENDS SAFETY FIRST
We at Catler are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer foremost in mind. In
addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions:
IMPORTANT SAFEGUARDS FOR YOUR MILK FROTHER MF 8010
• Carefully read all instructions before operation and save for future reference.
• Remove and safely discard any packaging
material and promotional labels before using
the appliance for the first time.
• To eliminate a choking hazard for young
children, remove and safely discard the protective cover fitted to the power plug of this
appliance.
• This appliance has been designed specifically for the purpose of foaming milk and
other dairy milk alternatives only. Under
no circumstances should this product be
used to thicken or heat other food or liquid
substances e.g. cream, custards, soups and
gravies etc.
• This appliance is not designed to mix a large
quantity of dry ingredients or melt large food
pieces e.g. cubed chocolate, ground nuts,
whole spices, fresh herbs.
• Do not place the appliance near the edge of
a bench or table during operation. Ensure
that the surface is level, clean and free of
water.
• Do not place the appliance on or near a hot
gas burner, electric element or where it could
touch a heated oven.
• Keep the appliance clear of walls, curtains
and other heat or steam sensitive materials.
Minimum recommended distance is 20 cm.
• Do not operate the appliance on a sink drain
board.
• Before you connect the appliance into the
power outlet make sure the voltage on the
rating label corresponds to the voltage in
your power outlet.
• Always ensure the appliance is properly
assembled before connecting to a power
outlet and operating. Follow the instructions
provided in this book.
• This appliance is not intended to be operated
by means of an external timer or separate
remote control system.
• The underside of the jug must always be dry
before placing onto power base before use.
• The jug must be used only with the power
base supplied together with the jug. Do not
use this supplied power base and the jug for
other types of appliances unless the manufacture recommends otherwise.
• Before operation, ensure the jug lid is securely
attached to the jug. During heating do not
open the jug lid or do not manipulate in
any way. Scalding may occur from escaping
steam. Do not place anything on top of the lid.
• Do not touch hot surfaces. Use the handle for
lifting and carrying the appliance.
• Use caution when pouring foamed milk from
the jug after heating as hot milk may scald at
high temperatures.
• Do not move the appliance if turned on. Do
not manipulate with the appliance if placed
on the power base and turned on.
• Do not operate the appliance without liquid.
Always fill to at least the ‘MIN’ marking and
no more than the ‚MAX‘ marking inside the
jug to avoid scalding. Should it be operated
empty, the boil dry protection will shut the
power off automatically. Allow the appliance
to cool before refilling.
CATLER RECOMMENDS SAFETY FIRST
5
5
• Do not put metal or similar items into the
jug as this may damage or affect the operation of the unit.
• Always ensure the START/STOP button has
been pressed to cancel before attempting
to move the appliance, when the appliance
is not in use and before cleaning and
storing. The appliance is turned off if button
illumination goes off. Now, you can unplug
the appliance from the power outlet.
• If you do not use the appliance for a long
time or you attempt to leave unattended,
unplug the appliance from the power outlet.
• Do not disconnect the appliance from the
power point by pulling the electric cable - it
may damage the electric cable/power point.
Disconnect the cable from the power point
by gently pulling the plug of the electric
cable.
• Before refilling, leave the appliance to cool
down.
WARNING:
TO PROTECT AGAINST ELECTRIC SHOCK,
DO NOT IMMERSE THE POWER BASE,
POWER CORD OR POWER PLUG IN WATER OR ALLOW MOISTURE TO COME IN
CONTACT WITH THESE PARTS.
• Do not remove the jug from the power base
during operation. Ensure the appliance
has switched off after the temperature has
reached the selected temperature, before
removing the jug from the power base.
• The appliance is not intended for use by
young children or infirm persons unless
they have been adequately supervised by
a responsible person to ensure they can use
the appliance safely.
• Use only supplied accessories or recommended accessories by a manufacturer.
Otherwise it may result in fire, electric shock
or injury to persons.
• Keep the appliance clean. Refer to Care and
Cleaning (page 15).
WARNING:
DO NOT WASH THE POWER BASE UNDER
RUNNING WATER.
HOT SURFACE
WARNING:
AFTER USING THE AUTOMATIC MILK
FROTHER, THE JUG AND THE FROTHING
DISC ARE EXTERMELY HOT. UNDER NO
CIRCUMSTANCES TOUCH THE HOT SURFACE. USE THE HANDLE FOR LIFTING
AND CARRYING THE APPLIANCE.
6
CATLER RECOMMENDS SAFETY FIRST
IMPORTANT SAFEFUARDS FOR ALL ELECTRICAL APPLIANCES
• This appliance is for household use only.
• Unwind the power cord fully before use.
• Do not let the cord hang over the edge of a
table or counter, touch hot surfaces or become
knotted.
• This appliance is not intended for use by persons (including children) with reduces physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that
they do not play with this appliance.
• It is recommended to inspect the appliance
regularly. Do not use the appliance if power
supply cord, plug or appliance becomes
damaged in any way. Return the entire
appliance to the nearest authorised Catler
Service Centre for examination and/or repair.
• Any maintenance other than cleaning should
be performed at an authorised Catler Service
Centre.
• The installation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisable that a
safety switch with a rated residual operating
current not exceeding 30mA be installed in the
electrical circuit supplying the appliance. See
your electrician for professional advice.
• For the security reasons, we recommend to
plug the Catler Automatic Milk Frother directly
to its own circuit, separate from other appliances. It is not recommended using hub or extension cord.
WARNING:
DO NOT OPERATE THE APPLIANCE ON
AN INCLINED SURFACE. DO NOT MOVE
THE APPLIANCE WHILE IT IS SWITCHED
ON.
WARNING:
ALWAYS ENSURE FROTHING DISC IS IN-
SERTED FIRMLY INTO JUG BEFORE USE.
WARNING:
FROTHING DISC IS A CHOKING HAZARD.
CHILDREN MUST ALWAYS BE SUPERVISED AND NEVER LEFT UNATTENDED
WITH APPLIANCE.
• Do not use this appliance for other than its intended use. Do not use in moving vehicles or
boats. Do not use outdoors.
CATLER RECOMMENDS SAFETY FIRST
7
KNOW YOUR MILK FROTHER MF 8010
Measuring Cap
For measuring and adding
ingredients once mixing has started
Jug Lid
With Assist™ Ring-Pull Removal.
Stainless steel jug with inner measurement
Press the centre of the dial to start or
stop operation. Turn the dial to adjust
the temperature. ‘COLD STIR’ setting stirs
Displays ‘Power On/Off’ and heating
8
KNOW YOUR MILK FROTHER MF 8010
Dishwasher Safe Jug
markings and pouring spout.
START | STOP Push-Dial
without heating.
LED Indicator
Cord Wrap
(Stored at the bottom of the
appliance)
‘On Board’ Disc Storage
Power Base
Induction Heating Technology
provides gentle, even heat
distribution.
‘Latte’ Frothing Disc
For smooth and silky milk.
‘Cappuccino’ Frothing Disc
For thick and creamy froth.
Operating
9
OPERATING YOUR MILK FROTHER MF 8010
Before rst use
Before first use, remove and safely discard
all promotional labels and packing materials
attached to the device.
Wash the jug, lid and measuring cap in warm
soapy water and dry thoroughly. Wipe exterior
of appliance with a soft damp cloth and dry
thoroughly.
Place appliance on a flat level surface and plug
power cord into 230-240V outlet and turn power
‘On’.
Frothing hot milk
1. Turn the appliance ‘On’ at the power outlet.
2. Select the ‘Capp’ or ‘Latté’ frothing disc.
Choose ‘Capp’ disc for thick and creamy froth
or the ‘Latté’ disc for smooth and silky milk.
‘Capp’
3. Insert frothing disc firmly into position onto
the shaft at the base of the jug.
NOTE:
Always ensure frothing disc is firmly inserted into jug before adding liquid.
If disc is not inserted correctly it may
dislodge during operation.
‘Latté’
WARNING:
FROTHING DISC IS A CHOKING HAZARD.
CHILDREN MUST ALWAYS BE SUPER
VISED AND NEVER LEFT UNATTENDED
WITH APPLIANCE.
4. Pour the required amount of cold fresh milk
into the jug and cover with jug lid. Always
use cold milk and full the jug between the
MIN and MAX level markings.
MIN MAX
NOTE:
For optimum frothing results, do not
exceed the CAPP/LATTE MAX (500ml)
marking inside the jug.
10
OPERATING YOUR MILK FROTHER MF 8010
NOTE:
Never operate the appliance without the
minimum level of liquid in the jug.
The appliance will automatically turn off
if jug is empty. Wait for appliance to cool
down before re-use.
5. Place the jug correctly onto the power base,
ensuring the jug is dry and clean.
6. Turn the START | STOP dial to the desired
temperature. When frothing milk for
a cappuccino or latte, we recommend
staying within the ‘OPTIMUM MILK TEMP’
range, however this is up to your personal
preference.
If temperature setting is changed whilst in
operation, the appliance will stop at the new
temperature selected.
7. Press the START | STOP button to commence
frothing. The button surround will start
flashing.
NOTE:
Do not remove jug during operation.
To stop operation at any time, press the
START | STOP button once.
8. When liquid has reached set temperature,
the appliance will beep twce and stop.
This will take anywhere between 2 -7 minutes
depending on the quantity of milk used.
Carefully remove the jug from the power
base as the jug and contents will be hot.
Always remove the jug using the jug handle.
Do not place the jug on a table, plastic
surface or heat sensitive surface which may
scorch or melt. Remove the jug lid and pour
the frothed milk.
NOTE:
The frothing disc will be hot after
operation. Wait for jug to cool before
removing disc.
WARNING:
SURFACE OF THE JUG WILL BE HOT
DURING AND AFTER OPERATION. DO
NOT PLACE HOT JUG ON HEAT SENSITIVE
SURFACE.
WARNING:
DO NOT PLACE HOT JUG ONTO POWER
CORD.
NOTE:
The milk frother has been designed specifically for the purpose of foaming milk
and other dairy milk alternatives and is not
intended to whip, thicken or heat other
food substances eg. cream, custard, soup,
gravy etc.
The milk frother is not designed to mix a
large quantity of dry ingredients or melt
large food pieces eg. cubed chocolate,
ground nuts, whole spices or fresh herbs.
OPERATING YOUR MILK FROTHER MF 8010
11
11
Using the ‘Cold Stir’ setting
By selecting the ‘Cold Stir’ setting on the
temperature dial, you can froth cold or hot milk
without heating.
The ‘Cold Stir’ setting is ideal for making cold
beverages or blending ingredients.
The ‘Cold Stir’ setting will operate for 60 seconds.
NOTE:
Avoid adding sugary powders using
‘Cold Stir’ setting. Toppings and syrups
work best.
Adding ingredients
Using the measuring cap, gradually add ingredients a few minutes after the stirring cycle has
commenced, allowing the milk to warm rst.
Always add ingredients slowly and in small
quantities. Adding ingredients too quickly may
cause the frothing disc to dislodge or stop spinning.
NOTE:
A different frothing result may be
achieved depending on the ingredients
added.
Experiment with different milk options, ingredients and frothing discs to
achieve the desired result.
Safety features
• Standby Mode
After 30 seconds of non use the milk frother will
enter standby mode and the button surround
will cease to illuminate.
To activate the milk frother out of standby mode,
press the START | STOP button.
• Boil Dry Protection
The milk frother will automatically cease to operate if the jug overheats. This can be caused if the
jug is empty, if liquid is below the MIN measurement marking, or after consecutive uses. Wait
approximately 5 minutes for the milk frother to
cool down or fill the jug with water for faster
cooling.
Once adequately cooled, you will be able to activate the milk frother and recommence frothing.
• Thermal Fuse Protection
This feature protects the milk frother in case of
major fault.
The appliance will no longer be able to operate.
Immediately cease use and contact the
authorised Catler service centre.
12
OPERATING YOUR MILK FROTHER MF 8010
Preparation Guide
SUITABLE
LIQUIDS
SUITABLE
INGREDIENTS
FRESH MILK
UHT MILK
POWDERS /
FLAKES
TOPPINGS /
SYRUPS
HOT DRINKS
COW (Full cream
low fat, skim)
COW (Full cream
low fat, skim)
DRINKING
CHOCOLATE
CHOCOLATE
HOT CHOCOLATE CAPPUCCINO LATTÉ
SOY (Full cream
& low fat )
SOY (Full cream
& low fat )
COCOA
POWDER
COCOA
POWDER
GOAT
GOAT / SHEEP
CHAI TEA
HONEY
OAT / RICE ALMOND
CHOCOLATE
FLAT WHITE CHAI LATTÉ
RECIPES
COLD DRINKS
ICED
CHOCOLATE
Hints & Tips
These hints and tips will help you to improve the results of preparation of frothing milk and your favorite beverages.
• Always use cold, fresh (or freshly opened)
milk.
• For optimum frothing results, do not exceed
the CAPP/LATTE MAX (500ml) marking inside the jug.
• For best results, always start cycle and warm
milk first before adding ingredients.
• Remove excess air bubbles from frothed
milk by gently tapping jug on a bench.
• Swirl frothed milk in a circular motion before
pouring milk into a cup or glass.
ICED COFFEE
• Pour frothed milk promptly to avoid the milk
from separating. Frothed milk that is not
used immediately should not be reheated.
• Ensure jug and frothing disc are clean before
use.
SHEEP
FLAKES
MAPLE
OPERATING YOUR MILK FROTHER MF 8010
13
13
Care and Cleaning
CARE AND CLEANING
1. Make sure the device has been switched off
by pressing START/STOP button. The device
is switched off if push-dial backlight has
gone off. Unplug the power cord from the
power outlet before cleaning.
2. The jug and frothing disc will be hot after
use. Wait for jug and disc to cool before
rinsing in tap water.
3. Wash the jug, jug lid, measuring cap and
frothing disc in warm soapy water, rinse and
dry thoroughly.
4. The seal from the lid can be removed and
washed separately.
5. Wipe exterior of appliance with a soft, damp
cloth. Then dry thoroughly.
NOTE:
Only the jug, jug lid, measuring cap
and frothing discs can be washed in the
dishwasher (top shelf only).
WARNING:
NEVER IMMERSE THE POWER BASE IN
WATER OR ANY OTHER LIQUID. DO NOT
EXPOSE THE DEVICE OR ANY ITS PART
TO MOISTURE.
Storage
1. Ensure the appliance is switched off, cleaned
and dried before storing.
2. Ensure the jug is clean and dry.
3. One of the frothing disc can be stored onto
the shaft at the base of the jug and the other
disc can be attached into the “On Board”
Disc Storage.
4. Wrap the power cord around the power cord
storage under the power base.
5. Store the appliance upright position. Do not
place anything on top.
NOTE:
Let the jug and frothing disc cool down
thoroughly before disassembling and
cleaning.
NOTE:
Do not use alkaline or abrasive cleaning
agents, steel wool or scouring pads as
these can damage the surface.
NOTE:
USE A SOFT CLOTH AND MILD DETERGENT TO CLEAN THE APPLIANCE.
CARE AND CLEANING
15
151515
TROUBLESHOOTING
Problem Possible Cause What to Do
Milk is not foaming? • Milk is warm or too hot to foam. • Use cold, fresh milk.
Milk is not heating? • Ensure jug is correctly positioned onto power base.
Frothing disc is not moving or
is dislodged?
• Frothing disc is not inserted
correctly.
• Frothing disc has dislodged
during operation.
• Ingredients have been added
too quickly.
• Do not re-foam already heated milk.
• Try reducing milk volume in jug.
• Press START/STOP button to commence cycle.
• Ensure light is illuminated and not ashing.
• Increase temperature by turning the START | STOP dial to the right.
1. Stop operation.
2. Remove liquid from jug.
3. Insert disc rmly into jug.
4. Re ll jug with liquid.
5. Add ingredients (if desired) slowly and in small quantities.
Ingredients are not melting? • Ingredients have been added
Milk is too cold/too hot? • Adjust temperature dial to suit personal preference.
Emergency stop • To stop operation at any time, press the START | STOP button.
IMPORTANT:
If you add thick ingredients (e.g. syrup, powder
or large pieces, etc.) the amount of froth may be
reduced.
This is a normal event.
16
TROUBLESHOOTING
before milk has warmed up.
• Ingredients are too large.
Various types of milk (2%, soy milk, rice milk,
etc.), milk brands, amount of milk in the jug
a ect the amount of froth created.
To achieve the maximum amount of froth,
• Allow the milk frother to stir for a few seconds before adding
ingredients.
• Ensure ingredients are in small pieces.
• Always operate unit between MIN and MAX level markings inside jug.
Operation has stopped once the button surround has stopped
ashing.
use full-cream milk, the cappuccino froth
attachment and ll the jug up to the “CAPP /
LATTE MAX” mark.
Recipes
PÉČE AČIŠTĚNÍ
17
17
RECIPES
HOT CHOCOLATE
A heated beverage of shaved chocolate, melted
chocolate or cocoa powder blended with heated
and foamed milk or water and sugar.
CAPPUCCINO
Cappuccino is served very light and luke warm
with 1⁄3 espresso to 1⁄3 heated milk and a generous nal third of creamy froth. For added nesse,
dust with powdered chocolate.
18
RECIPES
CHAI LATTÉ
A chai latté is 3⁄4 heated and foamed milk avoured with spiced tea concentrate including
sugar and spices and topped with ground nutmeg or cinnamon.
FLAT WHITE
A single dose of espresso in a cup topped with
heated and foamed milk, 1⁄3 co ee and 1⁄3 milk.
LATTÉ
Latté is a blend of 1⁄3 espresso to 2⁄3 milk is made
with a single shot of espresso. Top with heated
and foamed milk, poured down the inside rim of
the glass to give a creamy consistency and perfect layer of froth.
ICED COFFEE /ICED CHOCOLATE
A cold beverage of cold, foamed milk mixed
with co ee and topped with ice cream, whipped
cream and chocolate shavings*.
* Substitute co ee with chocolate powder or
topping to make iced chocolate.
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS
Dispose of packaging material at a public waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
Changes to the text, design and technical specifi cations may occur without prior notice and we reserve the right to make these changes.
The meaning of the symbol on the product, its accessory or packaging indicates that this
product shall not be treated as household waste. Please, dispose of this product at your applicable collection point for the recycling
of electrical & electronic equipment waste. Alternatively in some states of the European Union or other European states you may
return your products to your local retailer when buying an equivalent new product. The correct disposal of this product will help save
valuable natural resources and help in preventing the potential negative impact on the environment and human health, which could be
caused as a result of improper liquidation of waste. Please ask your local authorities or the nearest waste collection centre for further
details. The improper disposal of this type of waste may fall subject to national regulations for fi nes.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the correct disposal method from local government
departments or from your seller.
This product meets all the basic EU regulation requirements that relate to it.
Due to continued product
improvement, the products
illustrated/photographed in
this brochure may vary slightly from the actual product.
MILK FROTHER
WWW.CATLER.EU
CUSTOMER SERVICE
INFO@CATLER.EU
Loading...