CAT 982 XE Technical Specifications

982 XE

Wheel Loader

Technical Specifications

Not all attachments available in all regions. Consult your Cat® dealer for specic congurations available in your region.

Engine Model Cat C13 Engine Power @ 1,700 rpm ISO 14396:2002 Gross Power @ 1,700 rpm SAE J1995:2014 Net Power @ 1,700 rpm ISO 9249:2007, SAE J1349:2011 Engine Torque (1,200 rpm) ISO 14396:2002 Gross Torque (1,200 rpm) SAE J1995:2014 Net Torque (1,100 rpm) ISO 9249:2007, SAE J1349:2011 Bore 130 mm 5.12 in Stroke 157 mm 6.18 in Displacement 12.5 L 763 in

• Cat engine meets U.S. EPA Tier 4 Final and EU Stage V emission standards.

• The net power advertised is the power available at the ywheel when the engine is equipped with fan, alternator, air cleaner and aftertreatment.

322 kW 432 hp

325 kW 436 hp

301 kW 404 hp

2197 N·m 1,620 lbf-ft

2218 N·m 1,636 lbf-ft

2054 N·m 1,515 lbf-ft

3

Buckets

Bucket Capacities 4.8-17.2 m36.25-22.5 yd

Operating Specifications

Static Tipping Load – Full 40° Turn

With Tire Deection 21 110 kg 46,526 lb No Tire Deection 22 418 kg 49,410 lb

Breakout Force 262 kN 59,060 lbf

• For a machine conguration as dened under “Weight.”

• Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verication between calculations and testing.

Transmission

Forward 1 6.2 km/h 3.9 mph Forward 2 11.8 km/h 7.3 mph Forward 3 20.9 km/h 13.0 mph Forward 4 39.5 km/h 24.5 mph Reverse 1 7.1 km/h 4.4 mph Reverse 2 13.5 km/h 8.4 mph Reverse 3 28 km/h 17.4 mph Reverse 4 N/A N/A

• Maximum travel speed in standard vehicle with empty bucket andstandard L4 tires with 914 mm (36 in) roll radius.

3

Weight

Operating Weight 35 510 kg 78,264 lb

• Weight based on a machine conguration with Bridgestone 875/65R29 VLTS L4 radial tires, full uids, operator, standard counterweight, ride control, cold start, roading fenders, Product Link™, open differential axles (front/rear), secondary steering, sound suppression, and a 6.1 m³ (8.0 yd³) general purpose bucket with BOCE.

2

982 XE Wheel Loader Specifications

Hydraulic System

Implement Pump Type Variable Displacement

Piston, Electro-Hydraulic

Implement System

Maximum Pump Output (1,400 rpm) 457 L/min 121 gal/min

Maximum Operating Pressure 34 300 kPa 4,975 psi

Optional 3rd Function MaximumFlow

Optional 3rd Function MaximumPressure at Work Tool

Hydraulic Cycle Time with Rated Payload:

Raise from Carry Position 5.3 sec

Dump, at Maximum Raise 1.7 sec

Lower, Empty, Float Down 3.1 sec

Total 10.1 sec

240 L/min 63 gal/min

20 684 kPa 3,000 psi

Brakes

Brakes Brakes meet ISO 3450:2011

standards

Axles

Front Fixed, open differential

Rear Oscillating, open differential

Sound

With Cooling Fan Speed at Maximum Value:

Operator Sound Pressure Level (ISO 6396:2008) 70 dB(A)

Exterior Sound Power Level (ISO 6395:2008) 110 dB(A)

Exterior Sound Pressure Level (SAE J88:2013) 75 dB(A)*

* Distance of 15 m (49.2 ft), moving forward in second gear ratio.

With Cooling Fan Speed at 70% of Maximum Value:**

Operator Sound Pressure Level (ISO 6396:2008) 70 dB(A)

Exterior Sound Power Level 107 dB(A)***

** For machines in European Union countries and in countries

that adopt the “EU Directives.”

*** European Union Directive “2000/14/EC” as amended by

“2005/88/EC.”

Air Conditioning System

• The air conditioning system on this machine contains the uorinated greenhouse gas refrigerant R134a (Global Warming Potential =

1430). The system contains 1.6 kg (3.5 lb) of refrigerant which has a

CO2 equivalent of 2.288 metric tonnes (2.522 tons).

Service Refill Capacities

Fuel Tank 426 L 112.5 gal

DEF Tank 21 L 5.5 gal

Cooling System 52 L 13.7 gal

Crankcase 37 L 9.8 gal

Transmission 77 L 20.3 gal

Differentials and Final Drives – Front 92 L 24.3 gal

Differentials and Final Drives – Rear 92 L 24.3 gal

Hydraulic Tank 153 L 40.4 gal

Cab

ROPS/FOPS ROPS/FOPS meet

ISO3471:2008 and ISO 3449:2005 Level II standards

3

982 XE Wheel Loader Specifications

Dimensions

All dimensions are approximate.

19

24

B†

6

5

4

3

2

1

8

9

7

10

11

12†

17†

18

20

21

A†

16†

14

15

13

22

26

23

Standard Lift High Lift

Height to Axle Centerline 871 mm 2'10" 871 mm 2'10"

1

Height to Top of Hood 3036 mm 10'0" 3036 mm 10'0"

2

Height to Top of Exhaust Pipe 3736 mm 12'4" 3736 mm 12'4"

3

Height to Top of ROPS 3801 mm 12'6" 3801 mm 12'6"

4

Height to Top of Product Link Antenna 3807 mm 12'6" 3807 mm 12'6"

5

Height to Top of Warning Beacon 4080 mm 13'5" 4080 mm 13'5"

6

Ground Clearance 428 mm 1'4" 428 mm 1'4"

7

Center Line of Rear Axle to Edge of Counterweight 2729 mm 9'0" 2843 mm 9'4"

8

Center Line of Rear Axle to Hitch 1900 mm 6'3" 1900 mm 6'3"

9

Wheelbase 3800 mm 12'6" 3800 mm 12'6"

10

Overall Length (without bucket) 8597 mm 28'3" 9104 mm 29'11"

11

Shipping Length (with bucket level on ground)*† 10 184 mm 33'5" 10 692 mm 35'1"

12

Hinge Pin Height at Carry Height 791 mm 2'7" 896 mm 2'11"

13

Hinge Pin Height at Maximum Lift 4741 mm 15'6" 5150 mm 16'10"

14

Lift Arm Clearance at Maximum Lift 3902 mm 12'9" 4069 mm 13'4"

15

Dump Clearance at Maximum Lift and 45º Discharge*† 3362 mm 11'0" 3771 mm 12'4"

16

Reach at Maximum Lift and 45º Discharge*† 1569 mm 5'1" 1631 mm 5'4"

17

Dump Angle at Maximum Lift and Dump (on stops)* 50 degrees 50 degrees

18

Rack Back at Maximum Lift* 57 degrees 56 degrees

19

Rack Back at Carry Height* 48 degrees 49 degrees

20

Rack Back at Ground* 39 degrees 40 degrees

21

Clearance Circle (dia) to Counterweight 13 938 mm 45'9" 13 976 mm 45'11"

22

Clearance Circle (dia) to Outside of Tires 13 911 mm 45'8" 13 911 mm 45'8"

23

Clearance Circle (dia) to Inside of Tires 6970 mm 22'11" 6970 mm 22'11"

24

Width over Tires (unloaded) 3456 mm 11'5" 3456 mm 11'5"

25

Width over Tires (loaded) 3471 mm 11'5" 3471 mm 11'5"

Tread Width 2540 mm 8'4" 2540 mm 8'4"

26

25

†Dimensions are listed in Operating Specifications charts. All height and tire related dimensions are with Bridgestone 875/65R29 VLTS L4 radial tires (see Tire Option Chart for other tires). "Width over Tires" dimensions are over

the bulge and include growth.

• All dimensions are approximate and based on machine equipped with 6.1 m3 (8.0 yd3) general purpose bucket with BOCE and Bridgestone 875/65R29 VLTS L4 radial tires (see Operating Specifications for other buckets).

4

982 XE Wheel Loader Specifications

Tire Options

Tire Brand Bridgestone Bridgestone Michelin Bridgestone Maxam Tire Size 875/65R29 875/65R29 875/65R29 33/65R29 875/65R29 Tread Type L–4 L–3 L–3 L–5 L–4 Tread Pattern VLTS VTS XHA2 VSDL MS405DX

Width over Tires – Maximum (empty)* 3456 mm 3455 mm 3496 mm 3440 mm 3474 mm

11'5" 11'5" 11'6" 11'4" 11'5"

Width over Tires – Maximum (loaded)* 3471 mm 3464 mm 3491 mm 3457 mm 3486 mm

11'5" 11'5" 11'6" 11'5" 11'6"

Change in Vertical Dimensions (average of front and rear)

Change in Horizontal Reach 2 mm –1 mm –30 mm 0 mm

Change in Clearance Circle to Outside of Tires –7 mm 20 mm –13 mm 16 mm

Change in Clearance Circle to Inside of Tires 7 mm –20 mm 13 mm –16 mm

Change in Operating Weight (without Ballast) –76 kg –356 kg 1240 kg 60 kg

Change in Static Tipping Load – Straight –50 kg –236 kg 822 kg 40 kg

Change in Static Tipping Load – Articulated –44 kg –206 kg 718 kg 35 kg

Rear Axle Oscillation Angle

Maximum Single-wheel Rise and Fall

±13 degrees ±13 degrees ±13 degrees ±13 degrees ±13 degrees

571 mm 571 mm 571 mm 571 mm 571 mm

1'10" 1'10" 1'10" 1'10" 1'10"

–3 mm –13 mm 37 mm –19 mm

–0.1" –0.5" 1.5" –0.7"

0.1" 0" –1.2" 0"

–0.3" 0.8" –0.5" 0.6"

0.3" –0.8" 0.5" –0.6"

–168 lb –785 lb 2,734 lb 132 lb

–111 lb –520 lb 1,811 lb 88 lb

–97 lb –454 lb 1,583 lb 77 lb

*Width over tire bulge and includes tire growth.

5

982 XE Wheel Loader Specifications

Bucket Fill Factors and Selection Guide

The bucket size must be chosen based on the density of the material and on the expected fill factor. The Cat Performance Series Buckets with longer floor, larger bucket opening, increased repository angle, rounded side boards and integrated spill guard, demonstrate fill factors significantly higher than previous generation or non Cat buckets. The actual volume handled by the machine is thus often larger than the rated capacity.

Loose Material Fill Factor (%)* Material Density

Earth/Clay

Sand and Gravel

Aggregate: 25-76 mm (1 to 3 in)

19 mm (0.75 in) and smaller

Rock: 76 mm (3 in) and larger

*As a % of ISO 7546 rated capacity. Note: Fill Factors achieved will also depend on whether the product is washed or not washed.

115 1.5-1.7

110 1.6-1.7

105 1.8

100 1.6

Material Density kg/m

6.1 m3 (8 yd3)

6.4 m3 (8.25 yd3)

General Purpose

Pin OnHook On

Standard Linkage

General Purpose

Pin OnPin On

7 m3 (9.25 yd3)

7.5 m3 (9.75 yd3)

6 m3 (7.5 yd3)

6.7 m3 (8.75 yd3)

6.1 m3 (8 yd3)

6.4 m3 (8.25 yd3)

7 m3 (9.25 yd3)

7.5 m3 (9.75 yd3)

3

900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400

6.1 m3 (8 yd3)7 m3 (9.25 yd3)

6.4 m3 (8.25 yd3)7.4 m3 (9.75 yd3)

7 m3 (9.25 yd3)8.1 m3 (10.5 yd3)

7.5 m3 (9.75 yd3)8.6 m3 (11.25 yd3)

6 m3 (7.5 yd3)6.9 m3 (9 yd3)

6.7 m3 (8.75 yd3)7.7 m3 (10 yd3)

6.1 m3 (8 yd3)7 m3 (9.25 yd3)

6.4 m3 (8.25 yd3)7.4 m3 (9.75 yd3)

7 m3 (9.25 yd3)8.1 m3 (10.5 yd3)

7.5 m3 (9.75 yd3)8.6 m3 (11.25 yd3)

6.1 m3 (8 yd3)

6.4 m3 (8.25 yd3)

General Purpose

Aggregate Handler High Lift

Material Density lb/yd

115% 110% 105% 100% 95%

Note: All buckets are showing Bolt-On Edges.

7 m3 (9.25 yd3)

7.5 m3 (9.75 yd3)

8.2 m3 (10.75 yd3)

3

Bucket Fill Factor

6

6.1 m3 (8 yd3)7 m3 (9.25 yd3)

6.4 m3 (8.25 yd3)7.4 m3 (9.75 yd3)

7 m3 (9.25 yd3)8.1 m3 (10.5 yd3)

7.5 m3 (9.75 yd3)8.6 m3 (11.25 yd3)

8.2 m3 (10.75 yd3)9.4 m3 (12.25 yd3)

1,517 1,685 1,854 2,022 2,191 2,359 2,528 2,696 2,865 3,033 3,202 3,370 3,539 3,707 3,876 4,044

982 XE Wheel Loader Specifications

Bucket Fill Factors and Selection Guide

The bucket size must be chosen based on the density of the material and on the expected fill factor. The Cat Performance Series Buckets with longer floor, larger bucket opening, increased repository angle, rounded side boards and integrated spill guard, demonstrate fill factors significantly higher than previous generation or non Cat buckets. The actual volume handled by the machine is thus often larger than the rated capacity.

Loose Material Fill Factor (%)* Material Density

Earth/Clay

Sand and Gravel

Aggregate: 25-76 mm (1 to 3 in)

19 mm (0.75 in) and smaller

Rock: 76 mm (3 in) and larger

*As a % of ISO 7546 rated capacity. Note: Fill Factors achieved will also depend on whether the product is washed or not washed.

115 1.5-1.7

110 1.6-1.7

105 1.8

100 1.6

Material Density kg/m

5.1 m3 (6.75 yd3)

Rock,

Spade

5.6 m3 (7.25 yd3)

Coal 8.8 m3 (11.5 yd3)

Pin On

Waste 10.2 m3 (13.25 yd3)

Standard Linkage

12 m3 (15.75 yd3)

Woodchip

17.2 m3 (22.5 yd3)

Rock 5.4 m3 (7 yd3)

Coal 8.8 m3 (11.5 yd3)

Pin OnPin On

Waste 10 m3 (13.25 yd3)

Coal 8.8 m3 (11.5 yd3)

Waste 10.2 m3 (13.25 yd3)

3

300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100

5.3 m3 (7 yd3)8.5 m3 (6.44 yd3)

8.8 m3 (11.5 yd3)10.1 m3 (13.25 yd3)

10.2 m3 (13.25 yd3)11.7 m3 (15.25 yd3)

12 m3 (15.75 yd3)13.8 m3 (18 yd3)

17.2 m3 (22.5 yd3)19.8 m3 (25.75 yd3)

5.1 m3 (6.75 yd3)6.2 m3 (8 yd3)

8.8 m3 (11.5 yd3)7.4 m3 (9.75 yd3)

10.2 m3 (13.25 yd3)11.7 m3 (15.25 yd3)

8.8 m3 (11.5 yd3)10.1 m3 (13.25 yd3)

10.2 m3 (13.25 yd3)11.7 m3 (15.25 yd3)

4.9 m3 (6.25 yd3)5.9 m3 (7.75 yd3)

Aggregate Handler High Lift

Woodchip

Material Density lb/yd

115% 110% 105% 100% 95%

Note: All buckets are showing Bolt-On Edges.

12 m3 (15.75 yd3)

17.2 m3 (22.5 yd3)

3

Bucket Fill Factor

12 m3 (15.75 yd3)13.8 m3 (18 yd3)

17.2 m3 (22.5 yd3)19.8 m3 (25.75 yd3)

506 674 843 1,011 1,180 1,348 1,517 1,685 1,854 2,022 2,191 2,359 2,528 2,696 2,865 3,033 3,202 3,370 3,539

7

982 XE Wheel Loader Specifications

Operating Specifications – Buckets

Linkage Standard Linkage

Bucket Type General Purpose – Pin On – Abrasion

Edge Type

Capacity – Rated

Capacity – Rated at 110% Fill Factor

Width

Dump Clearance at Maximum Lift

16†

and45° Discharge

Reach at Maximum Lift and

17†

45° Discharge

Reach at Level Lift Arm and Bucket Level

Digging Depth

A†

Overall Length

12†

Overall Height with Bucket at

B†

Maximum Lift

Loader Clearance Circle Radius with Bucket atCarry Position

Static Tipping Load, Straight (ISO)*

Static Tipping Load, Straight (Rigid Tire)*

Static Tipping Load, Articulated (ISO)*

Static Tipping Load, Articulated (Rigid Tire)*

Breakout Force (§)

Operating Weight*

Bolt-On

Cutting

Edges

m36.10 6.10 5.70 6.40 6.40 6.10 7.00 7.00 6.70

yd38.00 8.00 7.50 8.25 8.25 8.00 9.25 9.25 8.75

m36.70 6.70 6.30 7.00 7.00 6.70 7.70 7.70 7.40

yd38.75 8.75 8.25 9.25 9.25 8.75 10.00 10.00 9.75

mm 3602 3665 3665 3602 3665 3665 3602 3665 3665

ft/in 11'9" 12'0" 12'0" 11'9" 12'0" 12'0" 11'9" 12'0" 12'0"

mm 3362 3194 3194 3325 3156 3156 3275 3106 3106

ft/in 11'0" 10'5" 10'5" 10'10" 10'4" 10'4" 10'8" 10'2" 10'2"

mm 1569 1703 1703 1602 1735 1735 1644 1776 1776

ft/in 5'1" 5'7" 5'7" 5'3" 5'8" 5'8" 5'4" 5'9" 5'9"

mm 3257 3468 3468 3307 3518 3518 3374 3585 3585

ft/in 10'8" 11'4" 11'4" 10'10" 11'6" 11'6" 11'0" 11'9" 11'9"

mm 119 119 84 119 119 84 119 119 84

in 4.6" 4.6" 3.3" 4.6" 4.6" 3.3" 4.6" 4.6" 3.3"

mm 10 184 10 419 10 419 10 234 10 469 10 469 10 301 10 536 10 536

ft/in 33'5" 34'3" 34'3" 33'7" 34'5" 34'5" 33'10" 34'7" 34'7"

mm 6590 6590 6590 6639 6639 6639 6706 6706 6706

ft/in 21'8" 21'8" 21'8" 21'10" 21'10" 21'10" 22'0" 22'0 22'0"

mm 7885 7993 7993 7900 8009 8009 7921 8030 8030

ft/in 25'11" 26'3" 26'3" 26'0" 26'4" 26'4" 26'0" 26'5" 26'5"

kg 24 782 24 683 25 102 24 573 24 474 24 904 24 339 24 239 24 655

lb 54,619 54,401 55,326 54,160 53,941 54,889 53,643 53,422 54,341

kg 26 088 25 989 26 426 25 888 25 788 26 234 25 661 25 560 25 993

lb 57,500 57,280 58,244 57,058 56,837 57,821 56,559 56,336 57,288

kg 21 110 21 011 21 400 20 910 20 810 21 209 20 685 20 585 20 972

lb 46,526 46,308 47,165 46,086 45,867 46,744 45,590 45,370 46,222

kg 22 418 22 318 22 724 22 226 22 126 22 540 22 009 21 908 22 310

lb 49,410 49,191 50,085 48,987 48,766 49,678 48,509 48,286 49,171

kN 262 262 281 253 253 271 242 242 258

lbf 59,060 58,913 63,246 57,055 56,907 60,981 54,561 54,413 58,177

kg 35 510 35 582 35 422 35 641 35 713 35 553 35 782 35 854 35 694

lb 78,264 78,423 78,070 78,552 78,712 78,359 78,863 79,023 78,670

Teeth and Segments Tips

Bolt-On

Cutting

Edges

Teeth and Segments Tips

Bolt-On

Cutting

Edges

Teeth and Segments Tips

* Static tipping loads and operating weights shown are based on a machine configuration with Bridgestone 875/65R29 VLTS L4 radial tires, full fluids, operator,

standard counterweight, ride control, cold start, roading fenders, Product Link, limited slip differentials, power train guard, secondary steering and sound

suppression. † Illustration shown with Dimension charts. ***Rock bucket specifications are given on Bridgestone 33/65R29 VSDL L5 radial tires. (§) Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C. (§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAEStandard J732C governing

loader ratings. (ISO) Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing. (Rigid Tire) Compliance to ISO 14397-1:2007 Sections 1 thru 5. Other buckets are available and offerings vary by region. Consult your local Cat dealer for further details.

8

982 XE Wheel Loader Specifications

Operating Specifications – Buckets (continued)

Linkage Standard Linkage

Bucket Type General Purpose – Pin On – Abrasion General Purpose – Pin On – HD

Edge Type

Capacity – Rated

Capacity – Rated at 110% Fill Factor

Width

Dump Clearance at Maximum Lift

16†

and45° Discharge

Reach at Maximum Lift and

17†

45° Discharge

Reach at Level Lift Arm and Bucket Level

Digging Depth

A†

Overall Length

12†

Overall Height with Bucket at

B†

Maximum Lift

Loader Clearance Circle Radius with Bucket atCarry Position

Static Tipping Load, Straight (ISO)*

Static Tipping Load, Straight (Rigid Tire)*

Static Tipping Load, Articulated (ISO)*

Static Tipping Load, Articulated (Rigid Tire)*

Breakout Force (§)

Operating Weight*

Bolt-On

Cutting

Edges

m37.50 7.50 7.20 8.20 8.20 7.90 7.50 7.50 7.00

yd39.75 9.75 9.50 10.75 10.75 10.25 9.75 9.75 9.25

m38.30 8.30 7.90 9.00 9.00 8.70 8.30 8.30 7.70

yd310.75 10.75 10.25 11.75 11.75 11.50 10.75 10.75 10.00

mm 3602 3665 3665 3602 3665 3665 3602 3665 3665

ft/in 11'9" 12'0" 12'0" 11'9" 12'0" 12'0" 11'9" 12'0" 12'0"

mm 3224 3055 3055 3151 2981 2981 3234 3064 3064

ft/in 10'6" 10'0" 10'0" 10'4" 9'9" 9'9" 10'7" 10'0" 10'0"

mm 1689 1820 1820 1755 1885 1885 1697 1828 1828

ft/in 5'6" 5'11" 5'11" 5'9" 6'2" 6'2" 5'6" 6'0" 6'0"

mm 3442 3653 3653 3542 3753 3753 3442 3653 3653

ft/in 11'3" 11'11" 11'11" 11'7" 12'3" 12'3" 11'3" 11'11" 11'11"

mm 119 119 84 119 119 84 107 107 72

in 4.6" 4.6" 3.3" 4.6" 4.6" 3.3" 4.2" 4.2" 2.8"

mm 10 369 10 604 10 604 10 469 10 704 10 704 10 362 10 597 10 597

ft/in 34'1" 34'10" 34'10" 34'5" 35'2" 35'2" 34'0" 34'10" 34'10"

mm 6773 6773 6773 6868 6868 6868 6777 6777 6777

ft/in 22'3" 22'3" 22'3" 22'7" 22'7" 22'7" 22'3" 22'3" 22'3"

mm 7943 8052 8052 7974 8085 8085 7938 8048 8048

ft/in 26'1" 26'5" 26'5" 26'2" 26'7" 26'7" 26'1" 26'5" 26'5"

kg 24 134 24 033 24 449 23 806 23 705 24 107 23 444 23 343 21 902

lb 53,192 52,970 53,887 52,470 52,245 53,133 51,670 51,448 48,273

kg 25 465 25 363 25 794 25 148 25 045 25 462 24 770 24 669 22 980

lb 56,124 55,900 56,851 55,426 55,199 56,119 54,594 54,370 50,649

kg 20 491 20 390 20 776 20 178 20 076 20 451 19 795 19 694 18 520

lb 45,163 44,940 45,791 44,473 44,249 45,075 43,629 43,407 40,818

kg 21 823 21 721 22 122 21 520 21 417 21 807 21 123 21 021 19 612

lb 48,097 47,873 48,757 47,432 47,205 48,062 46,555 46,331 43,225

kN 232 231 247 218 217 231 229 229 244

lbf 52,243 52,094 55,582 49,093 48,944 52,078 51,650 51,508 54,960

kg 35 888 35 960 35 800 36 073 36 145 35 985 36 564 36 636 36 476

lb 79,097 79,256 78,903 79,505 79,664 79,311 80,587 80,746 80,393

Teeth and Segments Tips

Bolt-On

Cutting

Edges

Teeth and Segments Tips

Bolt-On

Cutting

Edges

Teeth and Segments Tips

* Static tipping loads and operating weights shown are based on a machine configuration with Bridgestone 875/65R29 VLTS L4 radial tires, full fluids, operator,

standard counterweight, ride control, cold start, roading fenders, Product Link, limited slip differentials, power train guard, secondary steering and sound

suppression. † Illustration shown with Dimension charts. ***Rock bucket specifications are given on Bridgestone 33/65R29 VSDL L5 radial tires. (§) Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C. (§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAEStandard J732C governing

loader ratings. (ISO) Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing. (Rigid Tire) Compliance to ISO 14397-1:2007 Sections 1 thru 5. Other buckets are available and offerings vary by region. Consult your local Cat dealer for further details.

9

CAT 982 XE Technical Specifications

Technical Specifications

Table of Contents

Buckets

Operating Specifications

Transmission

Weight

Hydraulic System

Brakes

Axles

Sound

Air Conditioning System

Service Refill Capacities

Dimensions

Tire Options