How it Works
Casio
Loading...
DT-X200-20E
Hardware Manual
37 pgs1.02 Mb0

Casio DT-X8-20C-CNV, DT-X8-10C-CNV, DT-X200-20E, DT-X200-21E, DT-X200-10E Hardware Manual

...
Download
abc
DT-X200 Series
Hardware Manual
Th
DT-X200 Hardware Manual P.2
CAS
IO COMPUTER CO., LTD.
Revision history
Version Pages Contents
First (1.00) all First release
P.10,13, 17,
3.1.1 DT-X200 Leaser Scanner: Wave Length, Readable distance, Readable width C-MOS Imager: Readable width WLAN: Frequency, Communication Range, Output Power Bluetooth: Communication Range, Output Power Power: Operating period
1.10
P.18 Ethernet Cradle/USB Cradle: USB Client Baud Rate
DT-X200 Hardware Manual P.3
CAS
IO COMPUTER CO., LTD.
TABLE OF CONTENTS
1. OVERVIEW OF THE PRODUCTS .......................................................................................... 6
1.1. Main Unit Model Lineup.................................................................................................................................. 6
1.2. Options Model Lineup...................................................................................................................................... 6
1.3. Accessories........................................................................................................................................................ 7
1.3.1. Handheld Terminal.......................................................................................................................................7
1.3.2. Ethernet Cradle/ USB Cradle/ UAB and Charging Unit............................................................................7
1.3.3. Cradle-type Dual Battery Charger...............................................................................................................7
1.3.4. Dual Battery Charger ...................................................................................................................................7
1.3.5. AC Adaptor／Power Cord／USB Cable.......................................................................................................8
1.3.6. Screen Protect Sheet .....................................................................................................................................8
1.3.7. Battery Pack ..................................................................................................................................................8
2. OPTIONS AND INTERFACES ................................................................................................ 9
3. HARDWARE SPECIFICATIONS...........................................................................................10
3.1. Specification ................................................................................................................................................... 10
3.1.1. DT-X200 .......................................................................................................................................................10
3.1.2. Ethernet Cradle/ USB Cradle.....................................................................................................................18
3.1.3. USB and Charging Unit..............................................................................................................................19
3.2. External Views ............................................................................................................................................... 20
3.2.1. DT-X200 .......................................................................................................................................................20
3.2.2. Ethernet Cradle/USB Cradle......................................................................................................................22
3.2.3. USB and Charging Unit..............................................................................................................................23
3.2.4. Cradle-type Dual Battery Charger.............................................................................................................24
3.2.5. Dual Battery Charger .................................................................................................................................25
3.2.6. AC adaptor（AD-S42120C） ......................................................................................................................26
3.2.7. AC adaptor（AD-S15050B-N5） ................................................................................................................26
3.2.8. AC adaptor（AD-S90190-N5）...................................................................................................................26
3.2.9. Battery Pack (HA-K23XLBAT)......................................................................................................................26
3.3 Dimensions and Weight .................................................................................................................................. 27
3.3.1. Weight（DT-X200） ....................................................................................................................................27
3.3.2. Dimensions(DT-X200) .................................................................................................................................28
3.3.3. Ethernet Cradle...........................................................................................................................................29
3.3.4. USB Cradle..................................................................................................................................................29
DT-X200 Hardware Manual P.4
CAS
IO COMPUTER CO., LTD.
3.3.5. Dual Battery Charger .................................................................................................................................29
3.3.6. Cradle-type Dual Battery Charger.............................................................................................................29
3.3.7. USB and Charging Unit..............................................................................................................................29
3.3.8. AC adaptor...................................................................................................................................................29
3.3.9. Battery Pack ................................................................................................................................................29
４. QUALITY REFERENCES....................................................................................................30
4.1. Environmental Performances ........................................................................................................................ 30
4.1.1. DT-X200 .......................................................................................................................................................30
4.1.2. Ethernet Cradle/ USB Cradle/ USB and Charging Unit..........................................................................30
4.1.3. Dual Battery Charger/ Cradle-type Dual Battery Charger......................................................................30
4.1.4. AC adaptor...................................................................................................................................................30
4.1.5. Battery Pack ................................................................................................................................................30
4.2. Electrical Performances ................................................................................................................................. 31
4.2.1. Ethernet Cradle...........................................................................................................................................31
4.2.2. USB Cradle／USB and Charging Unit......................................................................................................31
4.2.3. Dual Battery Charger .................................................................................................................................31
4.2.4. Cradle-type Dual Battery Charger.............................................................................................................31
4.2.5. AC Adaptor...................................................................................................................................................31
4.2.6. Battery pack ................................................................................................................................................31
4.3. Mechanical Performances .............................................................................................................................. 32
4.3.1. DT-X200 .......................................................................................................................................................32
4.3.2. Ethernet Cradle／USB Cradle／USB and Charging Unit.......................................................................32
4.3.3. Dual Battery Charger .................................................................................................................................32
4.3.4. Cradle-type Dual Battery Charger.............................................................................................................32
4.3.5. AC adaptor ...................................................................................................................................................32
4.3.6. Battery Pack ................................................................................................................................................32
4.4 Connection Durability (Handheld Terminal to Battery Charger and Cradle).............................................. 33
5．PRECAUTIONS...................................................................................................................34
(1)Operating Precautions...................................................................................................................................... 34
(A) Lithium-ion Battery Pack...............................................................................................................................34
(B) Others...............................................................................................................................................................34
(C) About the Waterproofing/Dustproofing ..........................................................................................................35
(2)Storage .............................................................................................................................................................. 35
(3)Safety precautions ............................................................................................................................................ 35
DT-X200 Hardware Manual P.5
CAS
IO COMPUTER CO., LTD.
6．MAINTENANCE...................................................................................................................36
7．SETUP AND INSTALLATION..............................................................................................36
Last page （inc
ludes Front page, Table of Contents and Revision History pages）
Specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose.
No part of this document may be produced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, without the express written permission of CASIO Computer Co., Ltd. in Tokyo
Japan. Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd.
makes no representations or warranties with respect to the contents or use of this manual and
DT-X200 Hardware Manual P.6
CAS
IO COMPUTER CO., LTD.
1. Overview of the Products
1.1. Main Unit Model Lineup
Model Laser Imager
Full range
imager
NFC WLAN
Remark
DT-X8-10C-CNV Yes No No No Yes
DT-X8-20C-CNV No Yes No No Yes
DT-X200-10E Yes No No No Yes DT-X200-11E Yes No No Yes Yes
DT-X200-20E No Yes No No Yes
DT-X200-21E No Yes No Yes Yes
DT-X200-41E No No Yes Yes Yes
1.2. Options Model Lineup
Model Product
HA-K60IO USB Cradle
HA-K60IO-CN USB Cradle for China
HA-K62IO Ethernet Cradle
HA-K62IO-CN Ethernet Cradle for China
HA-K65US USB and Charging Unit
HA-K65US-CN USB and Charging Unit for China
HA-F32DCHG Dual Battery Charger
HA-F32DCHG-CN Dual Battery Charger for China
HA-K36DCHGE Cradle-type Dual Battery Charger
HA-K36DCHGE-CN Cradle-type Dual Battery Charger for China
AD-S15050BE-CN AC Adaptor for USB Cradle/USB and Charging Unit for China
AD-S15050B-N5 AC Adaptor for USB Cradle/USB and Charging Unit
AD-S42120C-N5 AC Adaptor for Ethernet Cradle/Dual Battery Charger
AD-S42120C-CN AC Adaptor for Ethernet Cradle/Dual Battery Charger for China
AD-S90190C-CN AC Adaptor for Cradle-type Dual Battery Charger for China
AD-S90190C-N5 AC Adaptor for Cradle-type Dual Battery Charger
AC-CORD-EU
AC-CORD-TW
AC-CORD2-EU
AC-CORD2-TW
Power Cord
HA-K90PS5 Screen Protect Sheet
HA-K90PS5-CN Screen Protect Sheet for China
HA-K23XLBAT Battery Pack
HA-K23XLBAT-CN Battery Pack For China
DT-380USB-A USB Cable (Cradle-computer connection)
DT-380USB-A-CN USB Cable (Cradle-computer connection) for China
HA-K95HB Hand Belt
HA-K95HB-CN Hand Belt for China for China
DT-X200 Hardware Manual P.7
CAS
IO COMPUTER CO., LTD.
1.3. Accessories
1.3.1. Handheld Terminal
Name
DT-X200-10E DT-X200-20E DT-X200-21E DT-X200-41E
DT-X8-20C-CNV DT-X8-10C-CNV Remark
Battery Pack Yes Yes Yes
USB and Charging Unit Yes Yes No
AC Adaptor Yes Yes No
USB Cable Yes Yes No
Pen（Stylus ）
Yes Yes No
User’s Guide Yes Yes Yes
WEEE Note Yes No No
China ROHS Note No No No
Refer to DT-X200 User’s Guide
1.3.2. Ethernet Cradle/ USB Cradle/ UAB and Charging Unit
Name Excluding the China China Remark
User’s Guide No No
AC Adaptor No No
Power Cord No No
USB Cable No No
China ROHS Note No Yes
1.3.3. Cradle-type Dual Battery Charger
Name Excluding the China China Remark
User’s Guide Yes Yes
AC Adaptor No No Option, sold separately
Power Cord No No Option, sold separately
USB Cable No No Option, sold separately
China ROHS Note No Yes
Bottom bracket One One
Side bracket One One
Screws (for Bottom brackets) Two Two
Screws (for Side brackets) Two Two
1.3.4. Dual Battery Charger
Name Excluding the China China Remark
User’s Guide No No Refer to DT-X200 User’s Guide
AC Adaptor No No Option, sold separately
Connection Bracket One One Option, sold separately
screw Two Two Option, sold separately
DT-X200 Hardware Manual P.8
1.3.5. AC Adaptor／Power Cord／USB Cable
Name
Excluding the China China
Remark
User’s Guide
No
No
1.3.6. Screen Protect Sheet
Name
Excluding the China China
Remark
User’s Guide
No
No
1.3.7. Battery Pack
Name
Excluding the China China
Remark
User’s Guide
No
No
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.9
2. Options and Interfaces
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.10
3. Hardware Specifications
3.1. Specification
3.1.1. DT-X200
Item Specification Remark
ＣＰＵ
Marvell PXA320 806MHz
ＯＳ
Windows Embedded Compact7
Memory RAM
256MB
FROM
512MB
Laser Scanner Laser emit angle
Redirected downward at 7 degree
Wave Length
645～664nm
Optical Output
< 1mW
No. of scanning
100±20 scan/sec
Resolution
0.127mm(minimum) or greater
PCS
0.45(minimum) or greater
Readable distance
Approximately 40mm to 550mm
Readable width
Max. 424mm
- at 550mm depth
Daylight for scanning
50,000 Lux or less
Readable bar code symbologies
UPC-A/UPC-E/EAN8(JAN8)/EAN13(JAN13)/Codabar(NW-7)/Code39 Interleaved2of5(ITF)/MSI/Industrial2of5/Code93/Code128(EAN128) /IATA/GS1 DataBarOmnidirectional(RSS-14)/GS1 DataBarLimited(RSS Limited)/GS1 DataBar Expanded(RSS Expanded)/GS1 DataBar Stacked(RSS-14 Stacked)/GS1 DataBar Expanded Stacked(RSS Expanded Stacked)/GS1 DataBar Truncated(RSS-14 Stacked)/ GS1DataBar Stacked Omnidirectional(RSS-14 Stacked
C-MOS Method
CMOS Imager, 832 x 640, monochrome
Imager Aimer method
Laser 650nm, <1 mW
Laser emit angle
Redirected downward at 30 degree
Resolution
1D：0.127mm(minimum) or greater
2D Stacked：0.168mm(minimum) or greater
2D Matrix：0.191mm(minimum) or greater
PCS
0.45(minimum) or greater
Readable distance
1D : Resolution0.25mm ： 48～250mm
1D : Resolution0.5mm ： 72～400mm
2D stacked Resolution 0.25mm ： 43～230mm
2D matrix Resolution0.25mm ： 67～150mm
2D matrix Resolution0.5mm ： 51～300mm
Readable width
Max. 39mm（at 48mm depth）
Max. 275mm（at 400mm depth
）
Focal distance
5.0 inches
Daylight for scanning
50,000 Lux or less
Readable 1D symbologies
UPC-A/UPC-E/EAN8(JAN8)/EAN13(JAN13)/Codabar(NW-
7)/Code39/Code11 Interleaved2of5(ITF)/MSI/ISBT/Code93/Code128(GS1­128(EAN128)/GS1 DataBarOmnidirectional(RSS-14)/GS1 DataBarLimited(RSS Limited)/GS1 DataBar Expanded(RSS
Expanded)/Code32/GS1 DataBar Truncated（RSS-14 Truncated）
Readable Stacked 2D symbologies
PDF417/Mi
cro
PDF/C
omposite/Codablock
F/
GS1 DataBar Stacked Omnidirectional(RSS-14 Stacked Omnidirectional)/ GS1 DataBar Expanded Stacked(RSS Expanded Stacked)
-
Readable Matrix 2D symbologies
Aztec,DataMatrix,Maxicode,QR Code,Micro QR,HanXin Code
Vibrator Notification of scanning bar code
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.11
Item Specification Remark
C-MOS Method
CMOS Imager, 1280 x 1024 SXGA, monochrome
Imager Aimer method
Laser 650nm, <1 mW
（Full range） Laser emit angle
Redirected downward at 0 degree
Resolution
1D：0.127mm(minimum) or greater 2D Stacked：0.127mm(minimum) or greater 2D Matrix：0.168mm(minimum) or greater
PCS
0.45(minimum) or greater
Resolution
1D：130mm（Resolusion：0.127mm）～2500mm（Resolusion：1.0mm
）
2D Stacked：130mm（Resolusion：0.127mm）～2500mm（Resolusion
：
1.0mm
）
2D Matrix：100mm（Resolusion：0.38mm）～20000mm（Resolusion
：
20mm
）
Readable width
Max. 36mm（at 100mm depth
）
Max. 852mm（at 2500mm depth
）
Focal distance
Auto focus
Daylight for scanning
10,000 Lux or less
Readable 1D symbologies
UPC-A/UPC-E/EAN8(JAN8)/EAN13(JAN13)/Codabar(NW-7)/Code39 /Code32/Interleaved2of5(ITF)/MSI/Code93 /Code128(GS1-128(EAN128))/Code11/ISBT /IATA/GS1 DataBarOmnidirectional(RSS-14)/GS1 DataBarLimited(RSS Limited)/GS1 DataBar Expanded(RSS Expanded) /GS1 DataBar Truncated(RSS-14 Truncated)
Readable Stacked 2D symbologies
PDF417/Mi
cro
PDF/C
omposite/Codablock
F/
GS1 DataBar Stacked Omnidirectional(RSS-14 Stacked Omnidirectional)/ GS1 DataBar Expanded Stacked(RSS Expanded Stacked)
-
Readable Matrix 2D symbologies
Aztec,DataMatrix,Maxicode,QR Code(Model2),Micro QR
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.12
Item Specification Remark
Display Display device TFT
Display size 2.7 inches
No. of dots 240 (horizontal) x 320 (vertical) WVGA
See "Dead Pixels"
Dot pitch 0.171mm (horizontal) x 0.171mm (vertical)
Gradation 65,536 colors
Display font Scalable font
Backlight LED backlight
Viewing angle 80°(Left, Right, Up, Down) 10 or more contrast
Touch Panel Resistive expression analog touch panel
Plasti
c
Gesture operation
Indicator LED
Indicator 1：2colors (red,green,blue)LEDX1 status of charging battery pack, Indicator 2：2colors (red,green,blue)LEDX1 status of communication
Input Keyboard
Numeric Keys,Function Keys,Fn Key,CLR Key,Enter Key,L,R Key,Cursol Key,decimal Point Key
Backlight supported
Control keys Reset Switch,Power
Trigger keys Center, L, R
Vibrator Notification of scanning bar code
Dead Pixels
The LCD panel employed in this product uses high precision and substantial number of components which commonly cause a small number
of the pixels not to light or to remain lit all the time. This is due to the characteristics of LCD panel yield in accuracy over 99.99% and
permissible
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.13
Item Specification Remark
WLAN Standard IEEE 802.11a/b/g/n
Radio type Spread Spectrum
Modulation type
802.11a/g/n: OFDM(OrthogonalFrequencyDivisionMultiplexing）
802.11b: DSSS(Direct Sequence Spread Spectrum) BPSK,QPSK,CCK,16QAM,64QAM
Emission Designation
802.11a/g/n：D1D, G1D
802.11b：G1D
Frequency
＜Center frequency＞ IEEE802.11a/n W52:36/40/44/48ch(5.18 to 5.24GHz) W53:52/56/60/64ch(5.26 to 5.32GHz) W56:100/104/108/112/116/120/124/128/132/136/140ch (5.50 to 5.70GHz) IEEE802.11b 1 to 13ch(2.412 to 2.472Ghz) IEEE802.11g/n 1 to 13ch(2.412 to 2.472Ghz) ＜Frequency range＞ IEEE802.11a/n
5.15 to 5.35GHz(W52,W53)
5.47 to 5.725GH z(W56) IEEE802.11b
2.400 to 2.497GHz IEEE802.11g/n
2.400 to 2.4835GHz
Baud rate
802.11a/g : 54Mbps (maximum)
802.11b : 11Mbps (maximum)
802.11n : 65Mb
ps (
maximum
)
Communication range
802.11b/g/n : Approx.50m(indoor), Approx.150m(outdoor)
802.11a/n : A
pp
rox.50m(indoor), Approx.150m(outdoor
)
Number of channels
802.11a/n：W52:4,W 53:4,W56 : 11 (11n is 5GHz range)
802.11b : 13
802.11
g
/n : 13(11n is 2.4GHz range）
Channel spacing
802.11a/n : 20MHz (11n is 5GHz range)
802.11b/
g
/n : 5MHz(11n is 2.4GHz range）
Channel band width 802.11a/b/g/n： 20MHz Other feature Roaming among Access-Points
Output power
802.11a : 14dBm (maximum)
802.11b : 20dBm (maximum)
802.11g : 15dBm (maximum)
802.11n : 14dBm (maximum)
Security WEP(64/128bit), WPA, WPA2 WPA encrypted method TKIP, AES Authorize method PSK, EAP-TLS, PEAP-MSCHAP-V2
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.14
Item Specification Remark
Bluetooth Standard Bluetooth® Specification Ver.2.1+EDR
Radio type Spread Spectrum
Modulation Frequency Hopping Spread Spectrum ("FHSS")
Modulation type GFSK(1MbpS), Π/4-dqpsk(2Mbps), 8-DPSK(3Mbps)
Emission Designation F1D, G1D Frequency range 2.4000 to 2.4835GHz
Communication range Approx. 3 m
Vary depending on the
environment
Number of channels 79 Channel spacing 1MHz Channel band width 1MHz Output power Max. 4dBm(PowerClass2)
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.15
Item Specification Remark
NFC Carrier frequency 13.56MHz±7kHz
Antenna Magnetic loop antenna
Field work
Compatible with ISO10373­6
Compliant with ISO10373-7
Bit rate
ISO14443 Type A : 106kbps ISO14443 Type B : 106kbps Felica : 212kbps, 424kbps ISO15693 : 1.65kb
p
s
Modulation ASK Modulation rate 10%, 100% modulation
Read range
ISO14443 Type A/B, Felica : 0mm (Contact with case)
ISO15693
: 0mm (Contact with case) to 60mm (max)*
*Reference value because different with tag antenna design
Read area 32mm x 20mm Dependent on smart card Communicatio n
p
rotocol
Standard Y/N
Tested IC card
type
ISO14443 Type A Y
MIFARE Standard/ MIFARE Ultralight
ISO14443 Type B Y JICSAP
It is recommended to use smart card that is compliant with the ISO standard.
Felica （JIS X 6319)
Y FeliCa® Standard
ISO15693 Y
I・CODE SLI/I・ CODE SLI-S/I・ CODESLI-L/my-d VID plain/my-d Light/Tagitplus※ /Tag-it pro/Tag-it standard * There is some not support command.
The data writing by Tag­it is slowly. There is the commands that need to retry in user's application.
ISO18092 terminal to terminal communication
N
ISO18092 card mode N
Magnetic field strength (at 50mm distance from case) output 0.15A/m over
Magnetic field strength output 1.5A/m over
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.16
Item Specification Remark
Terminal layout
The l
ayout is viewe
d
when The terminal is placed with The display
Terminal table Refer to ＊1
microSD Compatible with SDHC Extension Port Speaker Monaural Microphone Monaural
Excluding the DT-X8
Power/Signal terminals
1
2
3
4
56
Pin assignment
＊１ Pin assignment table
Pin no. Signal Description Direction
1 V CRADLE Power supply / Charge to the terminal ­2D
＋
USB D
＋
IN/OUT
3D
－
USB D
－
IN/OUT 4 USB_ID Switch-over between USB host and USB client IN 5 V BUS Power from USB cradle ­6GND GND -
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.17
Item Remark
Power Operating power Lithium-ion battery pack
Memory backup Lithium battery (rechargeable) - Integrated
Operating period
Large Battery Pack Approx. 14 hours(1D) Approx. 13 hours(2D)
- WEB application mode
- Based on the ratio of cyclic operation of "Standby: Key input: Scanning: Calculate: WLAN" at 15:5:1:2:2
- Under the conditions that the CPU speed is set to auto power save mode and the backlight is turned on.
Large Battery Pack Approx. 25 hours(1D) Approx. 20 hours(2D)
- Based on the ratio of cyclic operation of “Standby: Key input: Scanning: WLAN” at 20 : 1 : 1 : 1.
- Under the conditions that the CPU speed is set to auto power save mode and the backlight is turned off.
Memory backup period (with memory backup battery only)
- Litium battery (on-board) is fully charged.
- At room temperature
Memory backup period (with battery pack and memory backup battery)
- The backup period starts when "Main battery low warning" appears.
Battery pack charge period
- Power of the terminal is turned off while the batter is being charged.
- At room temperature.
- Cradle(HA-K60IO, 62IO), USB and Charging Unit (HA­K65US)(with AC adaptor connected)
- USB and Charging Unit (HA-K65US)(with AC adaptor connected)
- At room temperature
Memory backup battery charge period
- Battery pack is being installed in the terminal.
- At room tem
p
erature.
Battery Pack Approx. 4 hours
Approx. 4 days (for fully charged level)
Approx. 10 minutes for RAM Approx. 72 hours for RTC
Specification
Approx 72hours for RAM
Battery Pack Approx. 8 hours
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.18
3.1.2. Ethernet Cradle/ USB Cradle
Specification Remark
Interface to DT-X200 Type Contact Connector
Communicate and power supply to DT-X200 Refer ＊１
Baud rate Full speed (12Mbps)　　
Protocol IEEE 802.3 Standard
Connector
USB connector A type
1 VBus 2 USB D­3 USB D+ 4 GND
Baud rate Full speed (12Mbps) Low speed not supported
Power to external device
5V±5%, 500 mA (maximum)
USB Client Connector
USB connector B type
1 VBus 2 USB D­3 USB D+ 4 GND
Baud rate Full speed (12Mbps) Low speed not supported
Input voltage DC 12V±5％ Adaptor AD-S42120C
Input voltage DC 5V±5％ Adaptor AD-S15050B
Input from AC Adaptor (USB Cradle)
Item
Input from AC Adaptor (Ethernet Cradle)
USB Host
LAN (Only Ethernet Cradle)
4
1
3
2
1 234
＊1
Pin Layout
The pin layout below shows when the cradle is viewed at its front.
Pin Layout and the description
Pin no. Signal Description Direction
1 V CRADLE Power supply to the terminal and charge to
battery pack installed in the terminal.
-
2 D + USB D + IN/OUT 3 D - USB D - IN/OUT 4 USB_ID Switch-over between USB host and USB
client
OUT (Note 1)
5 V BUS Power from/to USB cradle ­6 GND GND -
Notes:
1. The output is made from the cradle. The direction “OUT” is for USB mode, or “IN” for LAN mode.
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.19
3.1.3. USB and Charging Unit
Item Specification Remark
Standard USB Ver.1.1 compatible Baud rate Max. 12 Mbps (maximum) Pin Layout See Figure 2.9. Description See Table 2.10.
USB Client
Connector
12
43
USB connector B type
1 VBus 2 – Data (D -) 3 + Data (D+) 4 GND
Input voltage DC 5V±5% Current consumption DC 5V, Approx. 3A (maximum) When supplying power or
transmitting data.
Plug EIAJ RC-5320A type 2 Center +
Power from AC Adaptor
AC Adaptor AD-S15050B or AD-S15050B-CN Dedicated AC adaptor Output voltage DC5.0±0.25V Output current 3.0 A (maximum)
Power
Charge method Constant voltage method Charge by integrated
battery charge circuit
Pin Layout
The pin layout below shows when the Cradle is viewed at the front.
Pin Layout and the description
Pin no. Signal Description Direction 1 V CRADLE Power supply to the terminal and charge the
battery pack installed in the terminal.
-
2 D + USB D + IN/OUT 3 D - USB D - IN/OUT 4 USB_ID Switch-over between USB host and USB client* OUT 5 V BUS Power from USB cradle ­6 GND GND -
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.20
3.2. External Views
3.2.1. DT-X200
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.21
CAS
IO COMPUTER CO., LTD.
No. Name Description
1 Speaker Buzzer and voice messages are output.
Orange : Charging battery pack. Green : Charging battery pack is complete.
2 Indicator 1
Red : Battery pack is abnormal or the surrounding temperature is out of
the charging temperature range.
3 Indicator 2 Flashes in blue when operating via Bluetooth or in orange when operating via
WLAN. Lights in green when reading a bar code successfully or in red when alarming or in magenta when available to communicate or in light blue when resume (programmable).
4 Touch Screen Displays text and operating instructions. Also used to operate the terminal and
enter data using stylus provided. 5 Cursor Keys These keys operate much like PC’s cursor keys. 6 Center Trigger Key Used to perform bar code reading. Can be assigned an arbitrary function. 7 Power Key Turns on and off the power. 8 R Key Available to set any function. 9 L Key Available to set any function.
10 Execute Key Press when finishing entering numerical values or when moving to the next
step.
11 Numeric Keys Used to enter numeric, decimal points, and letters. 12 Function Keys Various functions other than bar code reading can be assigned to these keys.
The assignments by default on the keys are as follows.
F1: Deletes the character on the left side of the cursor.
F2: Not assigned
F3: Not assigned
F4: Inputs “-“ (minus).
F5: Inputs a space.
F6: Not assigned.
F7: Not assigned.
F8: Changes text input mode. The input mode navigates to Numeric
Uppercase letter Lowercase letter.
13 Microphone Used to input a sound including voice sound. See note. 14 Fn Key Used to make various settings in combination with the function keys or
numeric keys or when starting a pre-registered application.
15 CLR Key Used to clear one letter to the left of the input key. 16 Strap Holes Used to attach the hand strap. Also used for the hand belt. 17 micro SD Card Slot For insertion of a micro SD card into the slot in the battery compartment. 18 R Trigger Key Used to perform bar code reading. 19 L Trigger Key Used to perform bar code reading. 20 USB and Charging Unit
Mount Holes
Used to perform to set DT-X8 into "USB and Charging Unit".
21 Reader Port Laser light (Laser scanner models) or LED light (C-MOS Imager models) is
emitted from this port that reads bar codes.
22 Hand Belt Setting part Used to set Hand Belt in this position. 23 Extension Port Provided for connecting an external device. 24 Battery Pack Cover Lock
Switch
Used to lock the battery cover and to release it.
25 Cradle Mount Holes Used to mount the terminal in cradle. 26 Battery Pack Cover Used to cover the battery compartment that holds the battery pack inside. 27 Reset Switch Used to reset the terminal. 28 Power/Signal Terminals Used for USB communication or to supply power to the terminal and to charge
the battery pack via Cradle.
DT-X200 Hardware Manual P.22
3.2.2. Ethernet Cradle/USB Cradle
No. Name Description 1 USB Client Port This port is used to transmit data (download, upload) by connecting the Ethernet
Cradle to PC using USB cable (DT-380USB-A). The dedicated driver must be installed in the PC before connecting the cradle to the PC.
2 USB Host Port This port is used to connect a USB peripheral device.
This LED shows the LAN connection status. Off : LAN cable not connected correctly.
3 LAN Connection Status
LED(Only Ethernet Cradle)
On in Green : LAN cable connected correctly. This LED shows the LAN operation status. Off : No communication.
4 LAN Communication
Status LED(Only Ethernet Cradle)
Flashing : Communication in progress.
5 LAN Port (Only Ethernet
Cradle)
This port is used for connecting the cradle to PC or hub via LAN cable so that data can be transmitted (uploaded or downloaded). The special driver must be
installed in the terminal. 6 AC Adaptor Jack Connect the dedicated AC adaptor, AD-S42120B, here. 7 Power Switch Turns on and off the power. 8 Selector Switch This switch is used to switch between USB connection and LAN connection. 9 Power/Signal Terminal Used for USB communication or to supply power to the terminal and to charge
the battery pack via Cradle. 10 Terminal Detect Switch This switch detects when the terminal is mounted correctly on the cradle. 11 Cradle Mound Hooks Used to hook the terminal in the cradle.
This LED indicates the power status and the mounting status of the terminal.
Off : The terminal is not mounted. Or, the AC adaptor is not
connected.
12 Power LED
On in Green : Power is turned on, and the terminal is correctly set in the
cradle.
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.23
3.2.3. USB and Charging Unit
No. Name Description 1 AC Adaptor Jack Connect the dedicated AC adaptor, AD-S15050B, here. 2 USB Client Port This port is used to transmit data (download, upload) by connecting the
Ethernet Cradle to PC using USB cable (DT-380USB-A). The dedicated driver must be installed in the PC before connecting the cradle to the PC.
3 Power/Signal Terminal Used for USB communication or to supply power to the terminal and to
charge the battery pack via Cradle.
4 Stoppers Used to fix the terminal in this unit.
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.24
3.2.4. Cradle-type Dual Battery Charger
No. Name Description
1 AC Adaptor Jack This is used to supply power by connecting the dedicated AC
adaptor, AD-S90190C, here.
2 Power Switch Turns on and off the power.
Used to connect multiple Dual Battery Chargers each other. 3 Dual Battery Charger
Connection Port
4 Connection Bracket Attachment
Holes
The connection bracket attaches here when you connect multiple
Dual Battery Chargers. 5 Power Supply Terminals Power Supply Terminals 6 Cradle Mound Hooks Used to hook the terminal in the cradle. 7 Power LED This LED indicates the power status.
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.25
3.2.5. Dual Battery Charger
No. Name Description
This LED indicates the charge status of battery pack(s).
Off : Battery pack is not mounted.
Red : Charging.
Flashing Red : Problem on battery pack.
Green : Charging complete.
1 Charge Indicator LED
Flashing Green : Standby in the out of charging temperature(0 to 40)
2 AC Adaptor Jack This is used to supply power by connecting the dedicated AC adaptor,
AD-S42120B, here.
3 Dual Battery Charger Connection
Port
Used to connect multiple Dual Battery Chargers each other.
4 Connection Bracket Attachment
Holes
The connection bracket attaches here when you connect multiple Dual
Battery Chargers.
5 Power Supply Terminals Terminals to the Battery
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.26
3.2.6. AC adaptor（AD-S42120C）
3.2.7. AC adaptor（AD-S15050B-N5）
3.2.8. AC adaptor（AD-S90190-N5）
3.2.9. Battery Pack (HA-K23XLBAT)
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.27
3.3 Dimensions and Weight
3.3.1. Weight（DT-X200）
Model Weight Remarks
DT-X200-10E
approximately
270g
with battery pack installed. Without hand belt and stylus
DT-X200-11E
approximately
275g
with battery pack installed. Without hand belt and stylus
DT-X200-20E
approximately
270g
with battery pack installed. Without hand belt and stylus
DT-X200-21E
approximately
275g
with battery pack installed. Without hand belt and stylus
DT-X200-41E
approximately
275g
with battery pack installed. Without hand belt and stylus
DT-X8-10C-CNV
approximately
270g
with battery pack installed. Without hand belt and stylus
DT-X8-20C-CNV
approximately
270g
with battery pack installed. Without hand belt and stylus
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.28
3.3.2. Dimensions(DT-X200)
DT-X200-10E/11E/20E/21E, DT-X8-10C-CNV/-20C-CNV
DT-X200-41E
CAS
IO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.29
CAS
IO COMPUTER CO., LTD.
3.3.3. Ethernet Cradle
Specific
ation Remark
Dimensions（W*D*H mm）
Approx.110.2 ×110.9 ×125.7 Includes rubber stand
Weight Approx. 325 g Includes rubber stand
3.3.4. USB Cradle
Specification Remark
Dimensions（W*D*H mm） Approx.110.2 ×110.9 ×125.7 Includes rubber stand
Weight Approx. 307 g Includes rubber stand
3.3.5. Dual Battery Charger
Specification Remark
Dimensions（W*D*H mm）
Approx.108×104×45
Weight Approx. 195g
3.3.6. Cradle-type Dual Battery Charger
Specification Remark
Dimensions（W*D*H mm） Approx.159×100×85
Weight Approx. 495g
3.3.7. USB and Charging Unit
Specification Remark
Dimensions（W*D*H mm） Approx. 63.5 ×44.5 ×66.2
Weight Approx. 57g
3.3.8. AC adaptor
AD-S15050B AD-S42120C AD-S90190C-N5
Remark
Dimensions（W*D*H mm）
Approx.50×75×30
mm
Approx.50×111×31
mm
Approx.45×128×30
mm
Weight
Approx. 165ｇ Approx. 275ｇ
Approx. 395g
Not including
AC Cord
3.3.9. Battery Pack
HA-K23XLBAT Remark
Dimensions（W*D*H mm）
Approx. 36.15 ×55.40 ×18.0
Weight
Approx. 65ｇ
DT-X200 Hardware Manual P.30
CAS
IO COMPUTER CO., LTD.
４. Quality References
4.1. Environmental Performances
4.1.1. DT-X200
Item Specification Remark/Condition
Operation -20to 50
0 to 40 ºC for charging battery
Temperature
Non-operation -20to 60
Operation 10% to 90%RH No condensation
Humidity
Non-operation 5% to 90%RH
Dust and waterproof IP67 Standard
4.1.2. Ethernet Cradle/ USB Cradle/ USB a
nd Charging Unit
Item Specification Remark/Condition
Operation 0℃ to 40℃
Temperature
Non-operation -20℃ to 60℃ Operation 10％ to 90％RH No condensation
Humidity
Non-operation
5％ to 95％RH
No condensation
Dust and waterproof Not applicable
4.1.3. Dual Battery Charger/ Cradle-type Dual Battery Charger
Item Specification Remark/Condition
Operation 0℃ to 40℃
Temperature
Non-operation -20℃ to 60℃
Operation 30％ to 80％RH No condensation
Humidity
Non-operation 10％ to 90％RH No condensation
Dust and water splash proof Not applicable
4.1.4. AC adaptor
Item Specification Remark/Condition
Operation 0～40℃
Temperature
Non-operation -20～60℃ Operation 20～80% No condensation
Humidity
Non-operation 10～90％
Dust and water-splash proof Not applicable
4.1.5. Battery Pack
Item Specification Remark/Condition
Operation
Compatible with the temperature range for the terminal during discharge, or with that of the battery chargers during charge.
Temperature
Non-operation
Compatible with the temperature range for the terminal
Operation
Compatible with the temperature range for the terminal during discharge, or with that of the battery chargers during charge.
Humidity
Non-operation
Compatible with the temperature range for the terminal
Dust and water-splash proof Not applicable
DT-X200 Hardware Manual P.31
CAS
IO COMPUTER CO., LTD.
4.2. Electrical Performances
4.2.1. Ethernet Cradle
Item Specification Remark/Condition
Input voltage DC12V±5%
4.2.2. USB Cradle／USB and Charging Unit
Item Specification Remark/Condition
Input voltage DC5V±5%
4.2.3. Dual Battery Charger
Item Specification Remark/Condition
Input voltage 12V±5%
Approx. 0.03A Without battery
Consumption Current
Approx. 1.17A(not connected) At charging with battery
Charging time
One battery mounted:
Approx. 4.5hours
Two batteries mounted:
Approx. 5hours
Room temperature
No. of connection Max 3 chargers
4.2.4. Cradle-type Dual Battery Charger
Item Specification Remark/Condition
Input voltage DC19V±1V
Consumption Current Approx. 1.6A (Not Multiple connection) Number of connection Max 3 chargers
4.2.5. AC Adaptor
Item AD-S15050B AD-S42120C AD-S90190C
Input voltage AC100V/240V AC100V/240V
AC100V/240V
Output voltage DC5V DC12V
DC19V
Output Current
0～3000mA 0～3500mA
0～4740mA
Input voltage Frequency
47Hz～63Hz 47Hz～63Hz
47Hz～63Hz
Output voltage Range
4.75V～5.25V 11.4V～12.6V
15.2V～16.8V
4.2.6. Battery pack
Item HA-K23XLBAT Remark/Condition
Rated Capacity 2860mAh
Rated Voltage 3.7V
DT-X200 Hardware Manual P.32
CAS
IO COMPUTER CO., LTD.
4.3. Mechanical Performances
4.3.1. DT-X200
Item Specification Remark/Condition
Drop Durability
Standard 1 : 2.5m Standard 2 : 3.0m
Standard 1: 5 cycles on each of 6 faces and 4 corners onto concrete floor (test criteria, not guaranteed) Standard 2: 1 cycles on each of 6 faces and 4 corners onto concrete floor (test criteria, not guaranteed)
4.3.2. Ethernet Cradle／USB Cradle／USB and Charging Unit
Item Specification Remark/Condition
Drop Durability
75cm
1 cycle on each of 6 faces onto concrete floor (test criteria, not guaranteed)
4.3.3. Dual Battery Charger
Item Specification Remark/Condition
Drop Durability
70cm
1 cycle on each of 6 faces and 4 edges onto concrete floor (test criteria, not guaranteed) Not in connected condition.
4.3.4. Cradle-type Dual Battery Charger
Item Specification Remark/Condition
Drop Durability
75cm
1 cycle on each of 6 faces and 4 edges onto concrete floor (test criteria, not guaranteed) Not in connected condition
4.3.5. AC adaptor
Item Specification Remark/Condition
Drop Durability 70cm
3 cycle on each of 6 faces onto P-tile surface (test criteria, not guaranteed)
4.3.6. Battery Pack
Item Specification Remark/Condition
Drop Durability 100cm
1 cycle on each of 6 faces onto P-tile surface. (test criteria, not guaranteed)
Note:
The drop durability height is a measured value resulting from actual testing. It does not necessarily guarantee the product from damage
DT-X200 Hardware Manual P.33
4.4 Connection Durability (Handheld Terminal to Battery Charger and Cradle)
Item Specification Remark
USB Cradle 15,000 times
for each USB Cradle
- 2 (terminals/Ethernet cradle) x 4 (times/day) x 365 (days/year) x 5 (years) （assume update in every one or two hours.）
Ethernet Cradle 15,000 times
for each Ethernet Cradle
- 2 (terminals/Ethernet cradle) x 4 (times/day) x 365 (days/year) x 5 (years) （assume update in every one or two hours.）
Cradle-type Dual Battery Ch
a
15,000 times
USB and Charging Unit 10,000 times 2 (times/day) x 365 (days/year) x 5 (years)
<Notes on Using These Products>
A limit applies to the number of times the handheld terminal can be placed in and removed from the cradle. The limit assumes
that these products are used as described above.
To exceed this limit in actual use, use multiple cradles or replace the cradle at set intervals so that the specified limit is not
exceeded for any one cradle.
Note that this information does not constitute a guarantee of any sort.
<Precautions>
Regularly clean the power-supply terminals and data communication terminals with a dry cotton bud, etc.
Soiling on the power-supply terminals and data communication terminals can cause connection defects and/or abnormal
wear.
Note that subjecting the cradle to impacts or strong vibration could dislodge the handheld terminal.
Also, place the cradle on a flat, level surface and take care when placing the handheld terminal in or removing it from the
cradle.
CASIO COMPUTER CO., LTD.
DT-X200 Hardware Manual P.34
CAS
IO COMPUTER CO., LTD.
5．Precautions
For information on general safety precautions, refer to the DT-X200 User’s Guide
(1)Operating Precautions
(A)
Lithium-ion Battery Pack
Each lithium-ion battery pack has its life. The life span heavily depends on how the battery pack is charged or stored, and it may cause
deterioration of the battery pack to shorten the life span if it is handled improperly. After charging the battery pack, if the performance of the
battery pack does not show any recovery, it is a sign of ending the life. Replace it with a new battery pack. Note the tips below to make the
battery pack last long.
— Be sure to charge the battery pack before using it if the battery pack is used for the first time or if it has not been used for a long period of
time. When charging the battery pack, continue charging until the charge LED lights green (fully charged).
— If the battery pack is repeatedly charged, the life span becomes short. To avoid the repetition of charging the battery pack, be sure that
the remaining capacity is low before you start charging.
— Be sure to charge the battery pack in recommended temperature range. The temperature range is dependant on device you use to charge
Including battery chargers and terminals. Refer to the respective user guides. Charging the battery pack in a temperature outside of the
recommended range cause deterioration.
— When used at low temperatures, the battery pack has a reduced capacity and will supply power for shorter time. The life span of the
battery pack is also shortened.
— Charging the battery pack while the battery pack itself is freeze including inside causes deterioration. Be sure to resume an ordinary room
temperature on the battery pack and then leave it unattended for approximately one hour before charging.
— Avoid the battery pack with a full of the capacity to store for a long period of time. If you need to store it for a long period, be sure that the
remaining capacity is 30 to 50 percent and to store in a moderate low temperature. This can reduce deterioration.
—
The battery pack gradually deteriorates over time. In particular, storing (or using) the fully charged battery pack at high temperatures
tends to accelerate battery pack deterioration.
(B) Others
1. The handheld terminal uses the high sensitive communication modules inside, for the better data communication , avoid using the
equipment to generate radio wave (mobile phone, etc) hear terminal. Please keep it away (more than 30 cm in case of the mobile phone)
when using it.
2. A microSD card must be inserted with the top and bottom properly aligned and in the proper direction.
Attempt in inserting it with an excessive force in incorrect orientation can risk damage to the connectors and slots.
3. Always make sure to connect the AC adaptor to the USB Cradle or Ethernet Cradle before performing communication with the Handheld
Terminal.
4. To ensure compliance with local regulations, be sure to follow the regulation of the country in which the access point is installed.
5. Do not use volatile chemical substances such as thinners, benzene or toiletries to clean the Handheld Terminal.
When the Handheld Terminal is dirty, wipe it clean with a soft, dry cloth. Rubbing with excessive force could scratch the display.
6. The power-supply terminals and Data Communication terminals should be cleaned from time to time using an implement such as a dry
cotton bud. Soiling on the terminals may cause connection defects.
7. Take care when using chemicals.
8. Applying thinners, gasoline, kerosene, solvents or oils, or substances such as cleaners, adhesives, paints, medications or toiletries that
contain those materials, to the plastic case or cover may cause discoloration or other damage.
DT-X200 Hardware Manual P.35
CAS
IO COMPUTER CO., LTD.
9. Stop or avoid using the Handheld Terminal and its options in areas and conditions subject to the following.
— Large amounts of static electricity
— Extreme heat or cold or humidity
— Sudden temperature change
— Large amount of dust
— After large amount of rain or water falls on the Handheld Terminal
— Pressing the screen or keys with excessive force when using in the rain
(C) About the Waterproofing/Dustproofing
Waterproofing: Performance complies with the IPX7 level set out in the IEC standards
(waterproof for 30 minutes at a depth of 1 meter in still tap water at normal temperature).
Dustproofing: Performance complies with the IP6X level set out in the IEC standards.
・ Check that there is no dust, sand or other foreign matter on the battery pack cover, microSD card slot cover or on the respective contact
surfaces. If any soiling is found, wipe it off with a clean, soft, dry cloth. Even very small amounts of soiling trapped on the contact surfaces
(a single hair or grain of sand, etc.) can cause water to leak into the device.
・ Check that the waterproof seals on the battery pack cover and microSD card slot cover are free from cracks and other damage.
・ Close the battery pack cover lock switch firmly until you hear it click into place.
・ Avoid opening and closing the battery pack cover or microSD card slot cover in locations near water or exposed to sea breezes, and do
not open or close them with wet hands.
・ Do not drop this product or leave it in locations exposed to temperatures outside the specified range.
Doing so could impair its water- or dust-proofing.
・ The accessories for this product(battery pack, etc.) and optional products are not water- or dust-proof.
・ Subjecting this product to a severe impact could render it no longer water- or dust-proof.
・ If any water leaks into the product as a result of carelessness or inattention during product handling,
CASIO cannot be held liable for compensation for any damage to internal components (battery, recording media, etc)
or for the costs of recorded content or the recording thereof.
・ CASIO COMPUTER CO., LTD. accepts no other liability whatsoever for any accident that occurs due to water leakage.
・ Be careful the use in the rain.
(2)Storage
1. During the long-term storage, please remove the battery.
2. Avoid keeping to store in high temperature location (ex, in the car).
(3)Safety precautions
Conform to user’s Guide.
DT-X200 Hardware Manual P.36
CAS
IO COMPUTER CO., LTD.
6．Maintenance
There are no parts for exchanging and checking regularly.
7．Setup and Installation
Adhere to the notes, perform the appropriate setup and operation.
DT-X200 Hardware Manual P.37
CASIO COMPUTER CO., LTD.
Notes
— Do not use or replicate of this software and manual without permission.
— This software and manual can be used only under license agreement for this product.
— CASIO COMPUTER CO., LTD. accepts no other liability whatsoever for any accident that occurs due to the results from the use of this
software and manual.
— The specifications of this software and the contents of this manual may be changed without notice.
— The copyright of this manual are the property of CASIO COMPUTER Co., ltd.
DT-X200 Hardware Manual
Ver.1.00 March 2015
© 2015 CASIO COMPUTER CO., LTD.
Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and licensed to CASIO COMPUTER CO., LTD. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use