Carrier 260L, 1300L User Manual

OWNER’S MANUAL

MIRACOOL™ GLASS DOOR MERCHANDISER

260L - 1300L

300L 750L

a79-13

a79-14

1300L

a79-15

Sales Office:
P.O. Box 5932

Spartanburg, S.C. 29304-5932

Technical Service: 1-800-558-7627

Parts Order Fax: [phone]

Printed in Mexico 6-06 79BC560002-01_C

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

CONTENTS

Page

GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

UNIT INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

LOCATE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

LEVEL UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALL SHELVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CONDENSATE DISPOSAL. . . . . . . . . . . . . . . . . . . . . . . . . . 5

START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,7

PRELIMINARY CHECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

INITIAL START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

REFRIGERATION SYSTEM SERVICE . . . . . . . . . . . . 8-13

COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SERVICE AND TROUBLESHOOTING . . . . . . . . . . . . . . . 8

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14,15

LAMP REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CONDENSATE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . 14

CONDENSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CABINET EXTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

INTERIOR SURFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

GENERAL

These instructions cover the installation, operation,
and maintenance of Carrier Miracool™ series glass
door merchandiser units, sizes 260L, 300L, 750L,
1100L, and 1300L.

UNIT INSPECTION

Examine all packages for damage to packaging mate­rial. Damage to external packaging may have resulted
in unit damage. Check packages for all accessories and
components, including legs, casters, and shelves. File
a claim immediately with the shipping company if
shipment is damaged or incomplete.

INSTALLATION

LOCATE UNIT

Refer to Figure 1 for unit components. Units are
designed for indoor placement only. Provide at least
3 in. of space between unit cabinet and any adjacent
wall or fixture. Remove skid base by removing the
retaining screws (4 hex head bolt screws). If optional
casters will be used, unit must be located on flat, level
surface. Refer to Table 1 for a list of standard parts.

TABLE 1 — STANDARD PARTS

PART

Refrigeration Cartridge X111

Shelves X4510

Shelf Clips X162040

Instruction Manual ——111

Leveling Feet X444

Lamps X122

NOTE: Parts shown are for standard units. Quantity of shelves and clips may vary based on factory-supplied options.

FAC TOR Y

INSTALLED

FIELD

INSTALLED

260L, 300L 750L 1100L, 1300L

UNIT SIZE

Quantity

2

FLUORESCENT LAMP SIGNBOARD
(SIZES 750L, 1100L, AND 1300L ONLY)

UNIT DATA LABEL
(INSIDE COOLER IN UPPER
LEFT CORNER)

SHELF

PRODUCT CHAMBER

INTERNAL FLUORESCENT LAMP —
SIZE 750L
(SIZE 260L, 300L — ALONG TOP;
SIZE 1100L, 1300L — IN CENTER)

FRONT GRILLE

CARTRIDGE COMPARTMENT

SERVICE
CORD

LEVELING FOOT

FRONT VIEW

GRILLE RETAINING SCREW

WOOD SKID RETAINING SCREW,
IF USED (HEX HEAD BOLT SCREW)

WOOD SKID

REAR VIEW

LIGHTING CORD
(RIGHT CONNECTOR)

POWER CORD
(LEFT CONNECTOR)

UNIT WITH FRONT GRILLE REMOVED

FIGURE 1 — MIRACOOL™ BOTTLE COOLER UNIT COMPONENTS (Size 750L Shown)

a79-1

3

LEVEL UNIT

To provide adequate condensate drainage and proper
door alignment and operation of unit, the unit cabinet
must be level. Leveling feet are factory installed.
Remove refrigeration system cartridge for easier
access to back feet.

Before servicing unit, disconnect electrical service.
On sizes 1100L and 1300L, turn disconnect switch
(located on power cord) to the OFF position. Failure
to disconnect electrical service could result in elec­trical shock and cause personal injury or death.

UNPLUG CARTRIDGE POWER
AND LIGHTING CORDS

a79-2

 TO REMOVE CARTRIDGE

1. After disconnecting the unit from the power
supply, remove the grille retaining screw located
in the upper-most part of the grille. (See Figure 1.)

2. Lift the grille up and away from the unit.

3. Unplug the power supply and lighting supply
cords located in the front of the cartridge
(Figure 2).

4. Using a pair of wire cutters, cut wire tie that
secures lifting rods at center of front base rail.
(See Figure 2.)

5. Take hold of the end of each lifting rod and rotate
each approximately 90-degrees upward so that
they are nominally vertical (Figure 3.) The car­tridge should be disengaged from the cabinet and
resting on the base of the cabinet assembly. Han­dling holes are located on either side of the car­tridge near the top and along the side of the
cartridge (Figure 4). Grasp the cartridge by these
holes and slide the unit forward from the cabinet
until the cartridge is free. Use caution to ensure
that power and electrical cords do not get pinched
between the cartridge and cabinet while removing
cartridge.

 TO LEVEL UNIT — The door is equipped with
gravity assisted cams and will not function properly
without proper leveling of cabinet. Adjust feet using
adjustable wrench so that unit sits approximately
level to floor and door closes properly. For best door
operation, adjust leveling feet so that cabinet has

1

a

/16-in. rake or slant from front to back. Optional

casters are available to replace leveling feet.

NOTE: If casters are not used, local codes may require
cabinet to be sealed around the perimeter of the cabi­net base. Consult local sanitation codes. Use only seal­ant material approved for this use, such as Dow
Corning #732.

CUT WIRE TIE THAT SECURES
LIFTING RODS TO BASE

FIGURE 2 — PREPARE CARTRIDGE FOR REMOVAL

CARTRIDGE POWER
AND LIGHTING CORDS

a79-3

FIGURE 3 — ROTATE LIFTING WIRES IN

DIRECTION SHOWN

PULL THE CARTRIDGE USING
THE HANDLING HOLES ON SIDES

a79-4

FIGURE 4 — REMOVE CARTRIDGE

4

INSTALL SHELVES

Product shelves and a bag containing shelf support
clips are packed inside the unit. Refer to Table 1 to
verify quantity of shelves and shelf supporting clips.
Bottom shelf must be placed on interior floor and
should be inserted into the two retainer clips provided
at the rear corners of the unit floor.

Improper shelf clip installation may cause shelf and/
or product to fall which could result in personal
injury or damage to the unit.

Do not overload the shelves. The unit is designed to
use all the shelves provided, installed in equally
spaced configuration. Failure to install shelves cor­rectly could result in personal injury or damage to
the unit. If fewer shelves or a different installation
configuration is desired, contact the manufacturer to
ensure that shelf overloading will not occur.

 TO INSTALL SHELVES — Refer to Figures 5 and 6.

1. Determine proper location for shelf clips. Refer to
the numbers on the pilaster to ensure that all
clips are properly located.

2. Insert top tab of the shelf clip into the desired hole
of the pilaster. The retaining tab should be facing
upward as shown in Figure 5.

3. Rotate the clip downward and insert the bottom
tab into the appropriate hole on the pilaster.
If necessary, squeeze the clip slightly during
installation.

4. Install all remaining clips as described above.

5. Install shelves onto clips so that the product
retention bar is facing upward. Be careful not to
dislodge clips during shelf installation.

6. Shelves must be placed so that the retaining tab
on the shelf clip captures the shelf as shown in
Figure 6.

7. Before loading the shelf, ensure that the shelf is
resting on each of 4 clips and that the clips are
installed as shown in Figures 5 and 6.

CONDENSATE DISPOSAL

The evaporator drain pan is located in the base of the
cartridge. Airflow in cartridge compartment hastens
condensate evaporation so that external drain plumb­ing is not required.

TOP TAB
FULLY INSERTED
INTO SLOT

BOTTOM TAB
FULLY SEATED

PROPERLY INSTALLED CLIP

RETAINING TAB

SHELF CLIP

a79-5

IMPROPERLY INSTALLED
CLIP (UPSIDE DOWN)

BOTTOM TAB

FIGURE 5 — SHELF CLIP INSTALLATION

PILASTER

SHELF
RETAINED
BY TAB

a79-6

PRODUCT
RETENTION BAR

FIGURE 6 — PROPER INSTALLATION OF

SHELF ON CLIP

TOP TAB

5