Canon LASER CLASS 810 BROCHURE

%.'

Starter Guide

Set Up the Machine

Before Setting Up the Machine

Remove all shipping tape on the machine.

●

When moving the machine, be sure at least two people carry it using the provided hand grips on the left and

●

right sides, as seen in the illustration right.

Do You Have Everything?

Machine● Paper Cassette (Optional)● Handset (Optional)●

Handset Cradle (Optional)*● Bracket (Optional)*● Screws (x2 for each type) (Optional)*●

Cartridge● Power Cord● Telephone Cable●

Ferrite Core**● Screw***● Screwdriver instruction label***●

Destination Label●

Starter Guide● User Software CD****● Registration Card● Limited Warranty Notice● Unpacking Instructions● Basic Operation Guide● User Manual CD (Reference Guide)●

* Included with the optional handset. (See “Install Handset (Optional),” on p. 10.) ** Use by attaching to a USB cable. Included with the LASER CLASS 830i and the optional network printer kit for the LASER CLASS 810. (See “Installation

Procedure for USB Connection,” on p. 23.) *** Used when the optional handset is installed. **** Included with the LASER CLASS 830i and the optional network printer kit for the LASER CLASS 810.

The machine illustration may diﬀer slightly from your machine.

–

Use the screw that is included with the machine, to secure the right cover and machine frame when attaching the handset

–

Manuals for the Machine

"ASIC

/PERATIONå

'UIDE

2EFERENCEå'UIDE

3ETUP

)NSTALLATION

(ANDLINGå

THEå-ACHINE

5SINGåTHEå$RIVERS.ETWORKå

&UNCTIONS

3TARTERå

'UIDE

Starter Guide (This Document)

●

Basic Operation Guide: Operation features, maintenance, speciﬁcations, functions you can use without being

●

connected to a network

Reference Guide (located on the User Manual CD): Operation features, maintenance, speciﬁcations, all functions

●

including those that use a network or driver

PCL Driver Guide (located on the User Software CD): PCL printer driver installation and instructions

●

UFR II Driver Guide (located on the User Software CD): UFRII LT printer driver installation and instructions

●

Fax Driver Guide (located on the User Software CD): Fax driver installation and instructions

●

Assistance:

If you have a problem with your machine and you cannot solve it by referring to the manuals listed above, please contact our Canon Authorized Service Facilities or the Canon Customer Care Center at 1-800-828-4040 between the hours of 8:00 A.M. to 8:00 P.M. EST Monday through Friday and 10:00 A.M. to 8:00 P.M. on Saturday.

Install Cartridge

Remove the toner cartridge from the bag. Keep the bag for future use.

Do not open the drum protective shutter (A).

Remove the seals (2 places).

Bend back the blue plastic pull tab as in the illustration above.

Gently rock the toner cartridge 5 or 6 times to distribute toner evenly.

Do not remove the pull tab as it is used to pull out the toner when the cartridge needs replaced.

Pull out the seal completely.

Do not pull out the seal at an angle.

Open the left cover.

Hold the toner cartridge by its handle. Insert the toner cartridge into the machine with the arrows (A) on the toner cartridge pointing toward the machine.

Push the toner cartridge to make sure it is properly set in the machine.

Do not touch the ﬁxing assembly (A) as it becomes very hot during use.

Close the left cover.

Be careful not to get your ﬁngers caught.

–

If you cannot close the left cover, do not force it to close. Open

–

the cover and make sure the toner cartridge is properly set in the machine.

The left edge (A) and the right side protrusions (B, C) of the toner cartridge should be aligned with the guides inside the machine. The Blue plastic pull tab should be pulled up as illustrated in step 4.

Load Paper

Pull out the paper cassette until it stops.

Gently insert the paper cassette as far as it will go.

Be careful not to get your ﬁngers caught.

For loading paper in the multi-purpose tray, see Chapter 2, “Document and Paper,” in the Basic Operation Guide, Reference Guide > What This Machine Can Do > Loading Paper.

Fan the paper stack and even the edges of the paper stack.

Load the paper stack print side up.

Make sure the back edge of the paper stack touches the rear paper end guide (C), the paper stack should not exceed the load limit mark (A), and the load is under the hooks (B) on the paper guides.

Set Up the Paper Cassette to Fit the Paper Size

Incline the rear paper end guide until it is unlocked, then remove it from the paper cassette.

Attach the guide to the slots of the desired paper size.

Connect the Power Cord and Turn On the Machine

F A X

Connect the power cord into the rear socket and the wall outlet and press the [I] side of the main power switch to ON. When restarting the machine, wait at least 10 seconds before turning the main power back on.

The machine enters standby mode.

<LEFT COVER OPEN / CLOSE COVER> is displayed:

●

Make sure that the left cover is closed properly. (See “Install Cartridge” on p. 4.)

<TONER IS NOT SET / INSERT TONER> is displayed:

●

Make sure that the toner cartridge is installed properly. (See “Install Cartridge” on p. 4.)

<TONER LOW / PREPARE NEW TONER> is displayed:

●

If this message is displayed after a new toner cartridge has been set in place, reset the toner cartridge after shaking it slowly ﬁve, or six times. (See “Install Cartridge” on p. 4.)

Connect Telephone Cables

Connect the supplied telephone cable to the line jack (A) and the wall jack. Connect your external telephone to the external device jack (B) if required.

If you want to use an external telephone and receive faxes, you will need to set up the receiving mode. (See “Set the Machine for Receiving Faxes,” on p. 17.)

Install Handset (Optional)

Use a screwdriver to remove the cover on the right side of the machine.

Screw the bracket onto the machine with the screws (A).

Place the handset on the cradle.

Attach the screws included with the machine to the center screw holes, and attach the driver instruction label below.

Screw the handset cradle onto the bracket with the screws (A). Make sure the groove (B) side of the cradle faces to the left.

If using the handset or an external telephone, make sure to set the fax receive mode to <FaxTel> or <Manual>. For how to set the receive mode, see “Set the Machine for Receiving Faxes,” on p.17.

Connect the curly cord terminal to the back of the modular terminal.

7 Connect the power cord into the wall outlet,

and turn the power on.

8 Conﬁrm that you can hear a dial tone from the

handset.

[Additional Functions]

[OK]

Numeric Keys [Clear] [Stop]

[ ][ ]

Set the Date and Time

You can set the current date and time. The current date and time settings are used as standard timer settings for functions that require them.

Use the keys both on the touch panel display and the control panel to enter information.

Numeric keys: Enter letters and numbers.

●

[ ] and [ ]: Move the cursor position.

●

[Clear]: Deletes the character at the cursor position, or the entire entry if held for more than one second.

●

+ 26 hidden pages