Canon FM33490 Users Manual

Legal Notices

FCC (Federal Communications Commission)

Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules, and the limits for an ISM equipment, pursuant to
Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate, radio frequency energy and, if not installed and
used in accordance with the Operator's Manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Use of shielded cables are required to comply with Class A limits in Subpart B of Part 15 of the
FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the
manual. If you make such changes or modifications, you could be required to stop operation of
the equipment.
If your equipment malfunctions, please contact your local authorized Canon dealer from whom
you purchased the equipment (if under warranty), or with whom you have a servicing contract. If
you are not sure who to contact, and have both purchased and are using the equipment in the
U.S.A., please refer to the "SUPPORT" page on Canon U.S.A.'s Web site
(http://www.usa.canon.com).

This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled
equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C
to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment
should be installed and operated with at least 20cm and more between the radiator and
person’s body (excluding extremities: hands, wrists, feet and ankles).

1/1

Wireless LAN Board NB-W1

User's Guide

Please read this guide before operating this product.
After you finish reading this guide, store it in a safe place for future reference.

Users in the European Union and other European countries

WEEE Directive

European Union (and EEA) only.

This symbol indicates that this product is not to be disposed of with your household

waste, according to the WEEE Directive (2002/96/EC) and your national law. This

product should be handed over to a designated collection point, e.g., on an

authorized one-for-one basis when you buy a new similar product or to an authorized

collection site for recycling waste electrical and electronic equipment (EEE).

Improper handling of this type of waste could have a possible negative impact on the

environment and human health due to potentially hazardous substances that are

generally associated with EEE. At the same time, your cooperation in the correct

disposal of this product will contribute to the effective usage of natural resources. For

more information about where you can drop off your waste equipment for recycling,

please contact your local city office, waste authority, approved WEEE scheme or

your household waste disposal service. For more information regarding return and

recycling of WEEE products, please visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

European Radio Approval Information (for products fitted with Euapproved radio devices)

This Product is a printer; low power, Radio LAN type devices (radio frequency (RF) wireless communication devices),

operating in the 2.4 GHz band, may be embedded in your printer system which is intended for office use. This section is

only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in the European Union or associated areas if a

CE mark with a Notified Body Registration Number and the Alert Symbol is on the system label.

The power output of the wireless device or devices that may be embedded in you printer is well below the RF exposure

limits as set by the European Commission through the R&TTE directive.

Regulatory Compliance Statements

Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4

GHzGHz Band, may be embedded in your printer system. The following section is a general overview of considerations

while operating a wireless device.

The equipment complies with the RF Exposure Requirement 1999/519/EC, Council Recommendation of 12 July 1999

on the limitation of exposure of the general public to electromagnetic fields (0 Hz to 300 GHz).

Preface

Thank you for purchasing a Canon product.

The Wireless LAN Board NB-W1 is a product that enables you to wirelessly connect your
Canon MFP (Color imageRUNNER/imageRUNNER/imagePRESS series) to a network.

This document describes the procedure for connecting a machine that includes the Wireless
LAN Board NB-W1 to a network.

Please read this manual thoroughly before operating the product to familiarize yourself with
its capabilities, and to make the most of its many functions. After reading this manual, store it
in a safe place for future reference.

How To Use This Manual

Symbols Used in This Manual

The following symbols are used in this manual to explain procedures, restrictions,
handling precautions, and instructions that should be observed for safety.

CAUTION

IMPORTANT

NOTE

Indicates a caution concerning operations that may lead to injury to
persons, or damage to property if not performed correctly. To use the
machine safely, always pay attention to these cautions.

Indicates operational requirements and restrictions. Be sure to read
these items carefully to operate the product correctly, and avoid damage
to the product.

Indicates a clarification of an operation, or contains additional
explanations for a procedure. Reading these notes is highly
recommended.

vi