Instruction manuals (PDF files) and software can be
downloaded from the Canon website (p.4).
www.canon.com/icpd
ENGLISH
INSTRUCTION
MANUAL
Introduction
The EOS-1D X Mark II (G) is a digital single-lens reflex camera
featuring a full-frame CMOS sensor (approx. 35.9 mm x 23.9 mm) with
approx. 20.2 effective megapixels, Dual DIGIC 6+, normal ISO speed
range of ISO 100 - ISO 51200, viewfinder with approx. 100% field of
view coverage, high-precision and high-speed 61-point AF (up to 41
cross-type AF points), maximum continuous shooting speed of approx.
14.0 fps during viewfinder shooting or approx. 16.0 fps during Live View
shooting, 3.2-inch (approx. 1.62 million dots) LCD monitor, Live View
shooting, 4K 59.94p/50.00p movie shooting, High Frame Rate movie
shooting (Full HD at 119.9p/100.0p), Dual-Pixel CMOS AF, and GPS
function.
Before Starting to Shoot, Be Sure to Read the Following
To avoid botched pictures and accidents, first read the “Safety
Precautions” (p.20-22) and “Handling Precautions” (p.23-25). Also, read
this manual carefully to ensure that you use the camera correctly.
Refer to This Manual while Using the Camera to Further
Familiarize Yourself with the Camera
While reading this manual, take a few test shots and see how they
come out. You can then better understand the camera. Be sure to store
this manual safely, too, so that you can refer to it again when
necessary.
Testing the Camera Before Use and Liability
After shooting, play images back and check whether they have been
properly recorded. If the camera or memory card is faulty and the
images cannot be recorded or downloaded to a computer, Canon
cannot be held liable for any loss or inconvenience caused.
Copyrights
Copyright laws in your country may prohibit the use of your recorded
images of people and certain subjects for anything but private
enjoyment. Also be aware that certain public performances, exhibitions,
etc., may prohibit photography even for private enjoyment.
2
Item Check List
Before starting, check that all the following items are included with your
camera. If anything is missing, contact your dealer.
Camera
Eyecup Eg
(with body cap and
battery compartment cap)
Wide Strap
* Attach the Eyecup Eg to the viewfinder eyepiece.
* Be careful not to lose any of the above items.
Battery Pack
LP-E19
(with protective cover)
Interface Cable
IFC-150U II
Battery Charger
LC-E19
(with protective covers)
Cable
protector
Wired LAN Functions
To use wired LAN with the Ethernet RJ-45 terminal (p.28), refer to the
EOS-1D X Mark II (G) “Wired LAN Instruction Manual” (p.4).
Connecting to Peripheral Devices
When connecting the camera to a computer etc., use the provided interface
cable or one from Canon. When connecting an interface cable, also use the
provided cable protector (p.38).
3
Instruction Manuals
Instruction manuals (PDF files) can be downloaded from the Canon
website.
Instruction manual (PDF files) download site:
• Camera Instruction Manual, Wired LAN Instruction Manual,
and Software Instruction Manuals
X www.canon.com/icpd
4
Compatible Cards
The following cards can be used with the camera regardless of
capacity: If the card is new or was previously formatted (initialized) by another camera or computer, format the card with this camera
(p.74).
CF (CompactFlash) cards
* Type I, UDMA Mode 7 supported.
CFast card
* CFast 2.0 supported.
Cards that Can Record Movies
When shooting movies, use a large-capacity card with good enough
performances (fast enough reading and writing speeds) to handle the
movie recording quality. For details, see page 316.
In this manual, “CF card” refers to CompactFlash cards and “CFast card”
refers to CFast memory cards. “Card” refers to all memory cards.
* The camera does not come with a card for recording images/movies.
Please purchase it separately.
5
Quick Start Guide
1
2
* Shooting is possible as long as there is a CF card or CFast card in the
camera.
3
4
Insert the battery (p.47).
To charge the battery, see page 42.
Insert the card (p.49).
The left slot is for CF cards, and the
right slot is for CFast cards.
Attach the lens (p.59).
Align the red mount index on the
lens with the red mount index on the
camera.
Set the lens’s focus mode
switch to <f> (p.59).
5
6
Set the power switch to <1>
(p.53).
Quick Start Guide
6
7
8
9
Set the shooting mode to <d>
(p.228).
Press the <W> button.Look at the top LCD panel and turn
the <6> or <5> dial to select
<d>.
Focus on the subject (p.62).
Look through the viewfinder and
aim the viewfinder center over the
subject.
Press the shutter button halfway,
and the camera will focus on the
subject.
Take the picture (p.62).
Press the shutter button completely
to take the picture.
Review the picture.
The image just captured will be
displayed for approx. 2 sec. on the
LCD monitor.
To display the image again, press
the <x> button (p.344).
To shoot while looking at the LCD monitor, see “Live View
Shooting” (p.271).
To view the images captured so far, see “Image Playback” (p.344).To delete an image, see “Erasing Images” (p.386).
7
Conventions Used in this Manual
Icons in this Manual
<6>: Indicates the Main Dial.
<5>: Indicates the Quick Control Dial.
<9>: Indicates the Multi-controller.
<0>: Indicates the Setting button.
9/4/7/8 : Indicates that each function remains active for
* In addition to the above, the icons and symbols used on the camera’s buttons
and displayed on the LCD monitor are also used in this manual when discussing
relevant operations and functionality.
3 : Indicates a function that can be changed by pressing the
<M> button to change its settings.
(p.**) : Reference page numbers for more information.
: Warning to prevent shooting problems.
: Supplemental information.
: Tips or advice for better shooting.
: Troubleshooting advice.
Basic Assumptions
All operations explained in this manual assume that the power switch
is already set to <1> (p.53).
It is assumed that all the menu settings and Custom Functions are
set to their defaults.
The illustrations in this manual show the camera attached with the
EF50mm f/1.4 USM lens as an example.
approx. 6 sec., 8 sec., 10 sec., or 16 sec. after you
let go of the button.
8
Chapters
1
6
11
1
14
1
Introduction
Getting Started
Setting the AF and Drive Modes
2
Image Settings
3
GPS Settings
4
Exposure Control for Photographic Expressions
5
Flash Photography
Shooting with the LCD Monitor
7
Shooting Movies
8
Image Playback
9
Post-Processing Images
10
Sensor Cleaning
Transferring Images to a Computer and Print Ordering
Image review timeÎ p.77Single-image displayÎ p.344Shooting information
displayÎ p.347
Index displayÎ p.352Image browsing
(Jump display)Î p.353
Magnified viewÎ p.355Image rotateÎ p.357ProtectÎ p.358RatingÎ p.361Voice memoÎ p.363Movie playbackÎ p.369Editing a movie’s first
and last scenesÎ p.372
Frame Grab (4K)Î p.374Slide showÎ p.376Viewing images on a
TV setÎ p.379
CopyingÎ p.382ErasingÎ p.386Quick ControlÎ p.365
Image Editing
RAW image processing Î p.392Resizing JPEGsÎ p.397Cropping JPEGs Î p.399
Image Transfer / Print Ordering
Image transferÎ p.408
Print Order (DPOF)Î p.413
Wired LAN
Î Wired LAN Instruction Manual
Customization
Custom Functions (C.Fn) Î p.418
Custom ControlsÎ p.443Custom Quick ControlÎ p.459My MenuÎ p.463Saving camera settings Î p.468Custom shooting mode Î p.472
Sensor Cleaning and Dust
Reduction
Sensor cleaningÎ p.402
Append Dust Delete Data Î p.403Manual sensor cleaning Î p.405
Interface
Cable protectorÎ p.38
Errors / Cautions
Camera system
informationÎ p.520
Error codesÎ p.523
Software
OverviewÎ p.550
InstallationÎ p.551Instruction ManualÎ p.4
19
Safety Precautions
The following precautions are provided to prevent harm or injury to
yourself and others. Make sure to thoroughly understand and follow
these precautions before using the product.
If you experience any malfunctions, problems, or damage to the
product, contact the nearest Canon Service Center or the dealer
from whom you purchased the product.
Warnings:
To prevent fire, excessive heat, chemical leakage, explosions, and electrical shock,
follow the safeguards below:
• Do not use any batteries, power sources, or accessories not specified in the
Instruction Manual. Do not use any home-made or modified batteries, or the
product if it is damaged.
• Do not short-circuit, disassemble, or modify the battery. Do not apply heat or
solder to the battery. Do not expose the battery to fire or water. Do not subject the
battery to strong physical shock.
• Do not insert the battery’s plus and minus ends incorrectly.
• Do not recharge the battery in temperatures outside the allowable charging
(working) temperature range. Also, do not exceed the recharge time indicated in
the Instruction Manual.
• Do not insert any foreign metallic objects into the electrical contacts of the camera,
accessories, connecting cables, etc.
When disposing of a battery, insulate the electrical contacts with tape. Contact with
other metallic objects or batteries may cause a fire or an explosion.
If excessive heat, smoke, or fumes are emitted when recharging the battery,
immediately unplug the battery charger from the power outlet to stop recharging.
Otherwise, it may cause a fire, heat damage, or electrical shock.
If the battery leaks, changes color, deforms, or emits smoke or fumes, remove it
immediately. Be careful not to get burned in the process. It may cause a fire,
electrical shock or burns if you keep using it.
Prevent any battery leakage from contacting your eyes, skin, and clothing. It can
cause blindness or skin problems. If the battery leakage comes in contact with your
eyes, skin, or clothing, flush the affected area with lots of clean water without
rubbing it. See a physician immediately.
Do not leave any cords near a heat source. It can deform the cord or melt the
insulation and cause a fire or electrical shock.
Do not hold the camera in the same position for long periods of time. Even if the
camera does not feel too hot, prolonged contact with the same body part may cause
skin redness or blistering due to low-temperature contact burns. Using a tripod is
recommended for people with circulation problems or very sensitive skin, or when
using the camera in very hot places.
Do not fire the flash at anyone driving a car or other vehicle. It may cause an accident.
Follow the warnings below. Otherwise, death or
serious injuries may result.
20
Safety Precautions
When the camera or accessories are not in use, make sure to remove the battery
and disconnect the power plug from the equipment before storing. This is to prevent
electrical shock, excessive heat, fire, and corrosion.
Do not use the equipment where there is flammable gas. This is to prevent an
explosion or a fire.
If you drop the equipment and the casing breaks open to expose the internal parts,
do not touch the exposed internal parts. There is a possibility of an electrical shock.
Do not disassemble or modify the equipment. High-voltage internal parts can cause
electrical shock.
Do not look at the sun or an extremely bright light source through the camera or
lens. Doing so may damage your vision.
Keep equipment out of the reach of children and infants, including when in use. Straps
or cords may accidentally cause choking, electrical shock, or injury. Choking or injury
may also occur if a child or infant accidentally swallows a camera part or accessory. If
a child or infant swallows a part or accessory, consult a physician immediately.
Do not use or store the equipment in dusty or humid places. Likewise, keep the battery
away from metallic items and store it with its protective cover attached to prevent
short-circuit. This is to prevent fire, excessive heat, electrical shock, and burns.
Before using the camera inside an airplane or hospital, check if it is allowed.
Electromagnetic waves emitted by the camera may interfere with the plane’s
instruments or the hospital’s medical equipment.
To prevent a fire and electrical shock, follow the safeguards below:
• Always insert the power plug all the way in.
• Do not handle a power plug with wet hands.
• When unplugging a power plug, grasp and pull the plug instead of the cord.
• Do not scratch, cut, or excessively bend the cord or put a heavy object on the
cord. Also do not twist or tie the cords.
• Do not connect too many power plugs to the same power outlet.
• Do not use a cord whose wire is broken or insulation is damaged.
Unplug the power plug periodically and clean off the dust around the power outlet
with a dry cloth. If the surrounding is dusty, humid, or oily, the dust on the power
outlet may become moist and short-circuit the outlet, causing a fire.
Do not connect the battery directly to an electrical outlet or a car’s cigarette lighter
outlet. The battery may leak, generate excessive heat or explode, causing fire,
burns, or injuries.
A thorough explanation of how to use the product by an adult is required when the
product is used by children. Supervise children while they are using the product.
Incorrect usage may result in electrical shock or injury.
Do not leave a lens or lens-attached camera in the sun without the lens cap
attached. Otherwise, the lens may concentrate the sun’s rays and cause a fire.
Do not cover or wrap the product with a cloth. Doing so may trap heat within and
cause the casing to deform or catch fire.
Be careful not to get the camera wet. If you drop the product in the water or if water
or metal get inside the product, promptly remove the battery. This is to prevent fire,
electrical shock, and burns.
Do not use paint thinner, benzene, or other organic solvents to clean the product.
Doing so may cause fire or a health hazard.
21
Safety Precautions
Cautions:
Do not use or store the product in a high-temperature location such as inside a car
under the hot sun. The product may become hot and cause burns. Doing so may
also cause battery leakage or explosion, which will degrade the performance or
shorten the life of the product.
Do not carry the camera around when it is attached to a tripod. Doing so may cause
an injury or an accident. Also make sure the tripod is sturdy enough to support the
camera and lens.
Do not leave the product in a low-temperature environment for an extended period of
time. The product will become cold and may cause injury when touched.
Do not fire the flash near the eyes. It may hurt the eyes.Never play the provided CD-ROM in a drive that is not compatible with the CD-ROM.
If you use it in a music CD player, you may damage the speakers and other
components. When using headphones, there is also a risk of injury to your ears from
excessively loud volume.
While listening with headphones, do not change the sound-recording settings. Doing
so may cause a blast of loud sound that will hurt your ears.
•
Follow the cautions below. Otherwise, physical injury
or property damage may result.
22
Handling Precautions
Camera Care
This camera is a precision instrument. Do not drop it or subject it to physical
shock.
The camera is not waterproof and cannot be used underwater. If you
accidentally drop the camera into water, promptly consult the nearest Canon
Service Center. Wipe off any water droplets with a dry and clean cloth. If the
camera has been exposed to salty air, wipe it with a clean, well-wrung wet
cloth.
Never leave the camera near anything having a strong magnetic field such
as a magnet or electric motor. Also, avoid using or leaving the camera near
anything emitting strong radio waves, such as a large antenna. Strong
magnetic fields can cause camera misoperation or destroy image data.
Do not leave the camera in excessive heat, such as in a car in direct
sunlight. High temperatures can cause the camera to malfunction.
The camera contains precision electronic circuitry. Never attempt to
disassemble the camera yourself.
Do not block the mirror operation with your finger, etc. Doing so may cause a
malfunction.
Use only a commercially-available blower to blow away dust when it adheres
to the lens, viewfinder, reflex mirror, focusing screen, etc. Do not use
cleaners that contain organic solvents to clean the camera body or lens. For
stubborn dirt, take the camera to the nearest Canon Service Center.
Do not touch the camera’s electrical contacts with your fingers. This is to
prevent the contacts from corroding. Corroded contacts can cause camera
malfunction.
If the camera is suddenly brought in from the cold into a warm room,
condensation may form on the camera and internal parts. To prevent
condensation, first put the camera in a sealed plastic bag and let it adjust to
the warmer temperature before taking it out of the bag.
23
Handling Precautions
If condensation forms on the camera, do not use the camera. This is to avoid
damaging the camera. If there is condensation, remove the lens, card and
battery from the camera, and wait until condensation has evaporated before
using the camera.
If the camera will not be used for an extended period, remove the battery
and store the camera in a cool, dry, well-ventilated location. Even while the
camera is in storage, press the shutter button a few times once in a while to
check that the camera is still working.
Avoid storing the camera where there are chemicals that result in rust and
corrosion such as in a chemical lab.
If the camera has not been used for an extended period, test all its functions
before using it. If you have not used the camera for some time or if there is
an important shoot such as a foreign trip coming up, have the camera
checked by your nearest Canon Service Center or check the camera
yourself and make sure it is working properly.
If you use continuous shooting, Live View shooting, or movie shooting for a
prolonged period, the camera may become hot. This is not a malfunction.
If there is a bright light source inside or outside the image area, ghosting
may occur.
LCD Panel and LCD Monitor
Although the LCD monitor is manufactured with very high precision
technology with over 99.99% effective pixels, there may be a few dead
pixels displaying only black or red, etc. among the remaining 0.01% or less
pixels. Dead pixels are not a malfunction. They do not affect the images
recorded.
If the LCD monitor is left on for a prolonged period, screen burn-in may occur
where you see remnants of what was displayed. However, this is only
temporary and will disappear when the camera is left unused for a few days.
The LCD monitor display may seem slightly slow in low temperatures, or
look black in high temperatures. It will return to normal at room temperature.
24
Handling Precautions
Cards
To protect the card and its recorded data, note the following:
Do not drop, bend, or wet the card. Do not subject it to excessive force,
physical shock, or vibration.
Do not affix any stickers, etc., on the card.Do not store or use the card near anything that has a strong magnetic field,
such as a TV set, speakers, or magnets. Also avoid places prone to having
static electricity.
Do not leave the card in direct sunlight or near a heat source.Store the card in a case.Do not store the card in hot, dusty, or humid locations.
Lens
After detaching the lens from the camera, put down the
lens with the rear end up and attach the rear lens cap to
avoid scratching the lens surface and electrical contacts.
Contacts
25
Nomenclature
Lens mount index (p.59)
Depth-of-field preview button (p.235)
Multi function button 2 (p.445)
Self-timer lamp (p.150)
Shutter button (p.62)
Grip
Vertical-grip On/
Off switch (p.67)
<B> Vertical-grip AF
area selection/
Multi function/FE Lock/
Multi-spot metering button
(p.67, 93/445/260/240)