Canon 1126C003AA User Manual

Introductory Information

479

Important

Caution

Note

7.9 inches (200 mm)

(600 mm)

7.9 inches (200 mm)

(600 mm)

(When not using the stand)

(When using the stand)

3.9 inches (100 mm)

7.9 inches (200 mm)

(600 mm)

7.9 inches (200 mm)

ENGLISH

Setup Guide

Read this manual before attempting to operate the printer. Keep this manual in a handy location for future reference.

• Instructions in this Setup Guide show the PRO-4000 printer. Note that your printer may look different from these illustrations in some cases. However, the basic operations are the same.

Introduction

Before Setting Up the Printer

Before setting up the printer, check the completed image of the printer you purchased and make sure you have enough space to install the printer. It is recommended that you reserve space of the following dimensions to allow you to work around the printer.

• The printer stand and roll unit may be options depending on the model. Care is required because the required space may differ depending on whether or not the options are used.

• The space required in front of the printer differs on how the basket supplied with the printer stand is used. This shows the installation space when used in the position in the illustration.

PRO-2000

Installation space (W x D x H)

• When not using the stand

59.5 x 56.5 x 40.2 inches (1510 x 1434 x 1020 mm)

• When using the stand

59.5 x 66.3 x 61.5 inches (1510 x 1684 x 1560 mm)

PRO-4000S

Installation space (W x D x H)

78.5 x 66.3 x 61.5 inches (1993 x 1684 x 1560 mm)

7.9 inches (200 mm)

23.6 inches (600 mm)

5.9 inches (150 mm)

3.9 inches (100 mm) (When not using the stand)

7.9 inches (200 mm)

(When using the stand)

5.9 inches (150 mm)

PRO-4000

Installation space (W x D x H)

78.5 x 66.3 x 61.5 inches (1993 x 1684 x 1560 mm)

PRO-6000S

Installation space (W x D x H)

94.5 x 66.3 x 61.5 inches (2399 x 1684 x 1560 mm)

7.9 inches (200 mm)

5.9 inches (150 mm)

3.9 inches (100 mm)

23.6 inches

5.9 inches (150 mm)

23.6 inches

Set up the printer using the following procedure.

Assemble the Stand

Install the Printer

Attach the Roll Unit

Attach the Basket

Turn On the Printer

Install the Ink Tanks

Install the Print Head

(P.3)

(P.4)

(P.6)

(P.8)

3.9 inches (100 mm)

Overview of Setup

* Refer to the separate manual

3.9 inches (100 mm)

23.6 inches

If an error message appears during setup or other problems occur, refer to "Responding to Messages" on p.14.

• Some items are included with the printer but not described in this manual. Keep these items in a safe place after setup because they are used invarious printing applications.

• For instructions on the included items not described in this manual, refer to the Online Manual. ("How to Display the Online Manuals" on p.14)

• A cable to connect the printer to a computer is not provided with the printer.

• Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.

Perform Print Head Adjustment and Select the Connection Method on the PRO-2000 Select the Connection Method and Perform Print Head Adjustment on the PRO-4000, PRO-4000S, and PRO-6000S

QT6-1290-V01 PRINTED IN XXXXXXXXXXXXXXXX © CANON INC. 2016

Load the Paper

Connect to the Printer

Store Accessories in the Pockets

How to Display the Online Manuals

(P.9)

(P.10)

(P.11)

(P.12)

(P.13)

(P.14)

RMC (Regulatory Model Code): K10441 RMC (Regulatory Model Code): K10440 RMC (Regulatory Model Code): K10439 RMC (Regulatory Model Code): K10438

● Printer

Package Contents

O, P, Q, R, S N

G F

A. Printer B. Basket rod / Basket cloth (*1) C. Paper for adjustment D. Setup Guide (this manual) E. Starter ink tanks (x 2) (*2) F. Set of CD-ROMs G. Set of printer documentation H. Rod holder (x 2) (*1)

*1 Only included with models where the stand is included as standard. Furthermore, it may be packaged in a separate box

depending on the region where you purchased the printer.

*2 The number and types of ink tanks differ between models.

For the PRO-2000 and PRO-4000 : MBK, PBK, C, M, Y, PC, PM, R, CO, B, GY, PGY For the PRO-4000S and PRO-6000S : MBK, PBK, C, M, Y, PC, PM, GY

*3 The holder stopper is used when loading roll paper. For details, refer to the Online Manual.

I. Print head J. Stand leg L (*1) K. Stand leg R (*1) L. Stand stay (*1) M. Basket arm (x 2) (*1) N. 3-inch paper core attachment (x 2) O. M4 hex screw (x 9) (*1) P. M8 hex screw (x 4) (*1)

Q. M4 Hex screw for basket arm (x 4) (*1) R. M8 Allen wrench (*1) S. M4 Allen wrench (*1) T. Accessory pocket (*1) U. Power cord V. Holder stopper (*3)

● Roll Unit

On the PRO-6000S, this is included as standard. On the PRO-2000, PRO-4000, and PRO-4000S, this is an option. Refer to the "Roll Unit Setup Guide" for details on the products included in the boxes.

The Manuals Supplied with This Printer

After installing the printer as shown in this Setup Guide, refer to the manuals for instructions on operation and maintenance.

Printed Manuals

Quick Guide

The Quick Guide contains information related to warnings for using this product safely and information related to replacing paper, ink tanks, and the print head.

Electronic Manuals

Online Manual

This manual describes advanced usage of the printer such as paper saving tips, how to print a poster and banner with the supplied software and print quality adjusting method, in addition to the basic instructions for printing on roll paper or cut sheet.

To view the electronic manuals, refer to "How to Display the Online Manuals" (p.14).

Caution

Assemble the Stand

• Models That Use a Stand Assemble the stand on which you will install the printer.

-> Refer to "Assemble the Stand" to "Prepare to Install the Printer" in the Printer Stand Setup Guide (separate manual).

• Models That Do Not Use a Stand Proceed to "Install the Printer".

Install the Printer

Remove the packaging material.

With 3 people holding the carrying handles under the printer on both ends, lift the printer.

• The printer alone weighs differently depending on the model. PRO-2000 is approx. 185 lb (84 kg), PRO-4000 is approx. 231 lb (105 kg), PRO-4000S is approx. 227 lb (103 kg), and PRO-6000S is approx. 260 lb (118 kg). Moving the printer requires at least 6 people, 3 on either side. Be careful to avoid back strain and other injuries.

Remove all of the tape and other packaging material. Open the top

• When moving the printer, rmly grasp the carrying handles (A) under each side. Holding the printer at other positions is dangerous and cause injury and damage if the printer is dropped.

cover (A) and output guide (B), and then remove the tape afxed to the roll holder.

• When setting the printer down temporarily make sure to put the printer on a at, stable place.

• When standing the printer up, make sure the side with the control panel is up, and place cardboard or other material underneath to prevent scratching. Furthermore, make sure that the weight of the printer is taken by the corner of the printer. If the weight is taken by any other part of the printer, the printer may become damaged.

• When standing up the printer or supporting the printer, hold the metal parts of the printer. If you hold a plastic part, the printer may become damaged.

• The way to set the printer down or to carry with the load only to the center of the printer, may cause damage to the printer.

Important

Note

Place the printer on the stand such that the protrusion (A) for aligning the position of the printer under the rear side of the printer is aligned with the position of the black marker on the basket rod attached to the supporting plate.

Afx the printer to the stand.

Remove the basket rod. Use an M4 Allen wrench to securely afx by using three M4

hex screws each on the left and right from the bottom of the supporting plate.

• If you are not using a stand, place the printer in the installation location and proceed to "Turn On the Printer".

Attach the Roll Unit

• Models That Use the Roll Unit Attach the roll unit to the stand.

-> Refer to the Roll Unit Setup Guide (separate manual).

• Models That Do Not Use the Roll Unit Proceed to "Attach the Basket".

Attach the Basket

• Models That Use a Stand Attach the basket to the stand.

-> Refer to "Attach the Basket" in the Printer Stand Setup Guide (separate manual).

• Models That Do Not Use a Stand Proceed to "Turn On the Printer".

Turn On the Printer

Open the top cover.

Pull up and remove the belt stopper (A).

• Keep the belt stopper you removed for future use. You will need them in case you move the printer to another location.

• When you open the top cover, a cleaning brush is stored on the right side. Take it out and use it when cleaning inside the top cover.

Peel off the tape afxed to the carriage, and then pull the protective material (A) towards you and remove it. Remove the protective sheet if there is one attached.

Plug the power cord into the power supply connector on the back of the printer.

Close the top cover.

PRO-2000

Plug the power cord into the outlet.

PRO-4000 / PRO-4000S / PRO-6000S

Turn on the printer.

When the language selection screen appears on the touch screen,

select and tap a language (lightly with your nger, and then move your nger away). Then, if the screen for selecting a time zone

appears, select and tap your region.

When a message prompting you to start the setup appears on the touch screen, tap OK.

+ 9 hidden pages