RCD 120BT(/B)
MANUAL
• GB •
The Operation Keys
Do Not Work
The Radio or
Automatic Selection
Does Not Work
Defected
The built-in microcomputer is
not operating properly due to
Interference
The antenna cable is not
connected correctly
The signals are too weak
a new one
Press the RESET button or
reinstall the front panel
properly
Connect the antenna cable
correctly
Select the station manually
TROUBLE SHOOTING
No Power
No Sound
Sound Skipping
The fuse is blown
Inserting the CD in reverse
direction
The CD is extremely dirty or
defected
Temperature inside the car is
too high
Condensation
Volume is at minimum
Wiring is not properly
connected
The installation angle is more
o
than 30
CD is extremely dirty or
Replace a new fuse
Remove the CD from the player
and insert the new one
Insert the CD with the label
facing up
Clean the CD or try to play
a new one
Cool off until the ambient
temperature return to normal
Leave the player off for an
hour or so and try again
Adjust volume to desired level
Check wiring connection
Adjust the installation angle to
o
less than 30
Clean the CD or try to play
A CD is already inside the
player slot
CD Cannot Be
Loaded or Ejected
The car ignition key not
been switched on
If the power supply is properly
connected to the car accessory
terminal, switch the ignition
key to ACC
Symptom
Causes Solution
Before going through the check list, check wiring connection. If any of the
problems persist after checklist has been made, consult your nearest service
dealer
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
Installation. ............................................... .02.
Additional information.................................04
General operations
Radio operations
CD/SD/MMC/USB Operations..................... 11
RDS operation
BLUETOOTH
.............................................
...............................................
MP3 WMA overview.....................................16
Specification.................................................17
Before playing discs..................................... 18
Trouble shooting
......................................
.........................................
15
............................................
19
05
09
14
INSTALLATION
PRECAUTIONS
Cho ose the moun ting loc at ion whe re the un it will not int erfere with the normal
driving function of the driver.
Bef ore final ly ins tal ling the uni t, co nne ct the wiring tem por arily and mak e sure
it is all connected up properly and the unit and the system work properly.
Use onl y the par ts incl uded wi th the uni t to ens ur e proper inst al lat ion. The use
of unauthorized parts can cause malfunctions.
Con sul t with you r ne ares t de al er if instal lat ion requires the dr illing of ho les or
other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop. Like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, form the heater, or where it would be
subject to dust, dirt or excessive vibration. Do not expose this equipment
to rain or moisture.
0
30
DIN FRONT-MOU NT (Method A)
Installing the unit
1. Dashboard
2. Holder
1
After inserting the holder into
the dashboard, select the
appropriate tab according to
the thickness of the dashboard
material and bend them
inwards to secure the holder in
(Fig. 1)
place.
3. Screw
2
3
(Fig. 1)
2
SPECIFICATION
General
Power Supply Requirements:
DC 14. 4V“ ”, Negative Ground
Maximum Output Power:
Chassis Dimensions: 178 x 163x 50mm (W x D x H)
Tone Controls
Bass (at 100Hz):
+10dB / -10dB
Treble (at 10K):
+10dB / -10dB
Current Drain:
10A
CD Player
Signal to Noise Ratio:
More than 60dB
Channel Separation:
More than 60dB
Frequency Response:
20Hz - 20KHz
FM Radio
Frequency Coverage (MHz):
87.5 - 108MHz
IF :
10.7MHz
Sensitivity (S/N-30dB):
12dBu
Stereo Separation:
>30dB
75W x 4( CH)
Load
Impedance:
4 ohms
Remarks:
Specifications subject to change without notice
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
INSTALLATION
1
6
7
4
2
3
(Fig. 2)
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
5
Removing the unit
1
2
3
(Fig. 3)
2. Insert fingers into the groove in the
front of fram e and pul l out to remove
the fram e. (When reatt achi ng the
frame, point the side with a groove
dow nwards and at tach it.)
3. Leve r
Insert the leve rs sup pl ied with the
uni t int o the grooves at both sides of
the uni t and show n in figure unti l they
click. Pull in g th e levers makes possible
to remove the unit fro m th e dashboard.
ADDITIONAL INFORMATION
RED YELLOW
BLUE
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
GREY/BLACK
VIOLET/BLACK
BLACK
GREY
VIOLET
B. T. ANT ENNA
RE AR Rc h LINE OUT
RE AR Lc h LINE OUT
Fastening the unit to the factory
radio mounting bracket:
1. Select a position where the screw
2
holes of the bracket and the
screw holes of the main unit
3
become aligned (are fitted), and
tighten the screws at 2 places on
each side. Use either truss screws
(5 x 5mm) or flush surface screws
(4 x 5mm)
2. Screw
3. Dashboard or Console
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit
INPUT THE SD CARD
The SD oblique angle keeps
rightward exposure, put into
the SD slot and press it again
to eject.
1.Pairing connect.
Turn on car unit, put your mobile near the unit, activate your mobile bluetooth
function.Soon the phone will find the new bluetooth device "CAR AUDIO" .
Input the pairing password “8888” and clik OK. The phone will prompt the
matching successful.When the pairing connect is successful,on the LCD, it shows
BT ON, and the bluetooth logo “ ”will stop blinking .Then you may perform the
bluetooth operation.
REMARK:depend on bluetooth mobile, the bluetooth system support “HSP” “HFP”
“A2DP” and AVRCP bluetooth profile.
2.Handsfree phone service
If your mobile phone have matched with the unit. You can dial calls out through your
mobile phone. It will turn to unit automatically when calling come in and the calling
phone number will indicat on the LCD screen.
-Press the “BAND” button shortly to accept the call .Then you can talk with the
other party through the mic on the panel.
-Press “MUTE” button shortly to reject the call when calling come in.
-Press “MUTE” button shortly to hang up after you finish the talk.
3.Advance Audio distributing profile(A2DP) playing.
Through mobile and unit A2DP connected, the music playing in mobile can turn
to the unit audio system play. Press button “ ”and “ ” in the panel can select
the music track.
-Press “ ” button shortly to pause the music playing.
-Press “BAND”(mode) longly to temporarily discommect the bluetooth.
-Press “BAND”(mode) button longly again to reconnect the bluetooth.
4.Phone number book.
This bluetooth system can automatically store incoming call numbers, up to
10 phone numbers.
-Press “MUTE”(mode) button longly to enter the phone number book and press
VOL button to look up the phone number.
-Press “BAND” button once can call out you desired phone number.
5. Interrupt bluetooth connection/reconnection.
Pressing the “BAND” button shortly to interrupt the bluetooth connection when
your are talking a call and the voice can turn to mobile speaker.
Press “BAND” button again to reconnection.
NOTE:Different mobile phone have different responses.We do not guarantee all the
operation of connectable devices.
6. How to delete stored phone number?
You jus t can store ten number of missed ,rejected and ANS under separately,
and the first number will auto deleted when the 11th number calling
7. How to use “Missed”,”Rejected””Auto ANS” Functions.
Press MUTE button for 3 seconds to enter into REVIEVED /MISSED/REJECTED/
ANTO .ANS .Turn VOL button for choosing the telephone number.
BLUETOOTH
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
GENERAL OPERATIONS
FRONT PANEL LAYOUT
6
MEN U
20
7 8
DISP
MU
5
19
11 12 13 14 15 16
4
3
2
1. Power / Mode / Next / Previous Button
2. Release Button
3. Menu / Volume Button
4. Mute / Button
5. Display Button
6. LCD Display
7. Flashing LED
8. Reset Button
9. Band/ switch /ID3 select
10. Automatically memory storing
11. Play / Pause & Preset Button 1
2/INT 3/RPT 4/RDM1/
17
12. Intro & Preset Button 2
13. Repeat & Preset Button 3
14. Random & Preset Button 4
15. Preset Button 5
16. Preset Button 6
20. SD/MMC Slot
21. AUX IN JACK
9
10
AMS
BND
21
18
17. Eject knob
18. CD Slot
19. USB connecter
1
MOD E
GENERAL OPERATIONS
GENERAL OPERATIONS
POWER /MOD conversion
2. Under power off status,short press is power on,
Under power on status,short press is switching mode,long press is power off.
FRONT PANEL RELEASE
Press REL button (2) to detach the removable front panel
SOUND ADJUSTMENT
Turn on (3) can adjust the desired volume quality.
A).Press MENU button (3) will change in the following order.
Option:
VOL BAS TRE BAL FAD
(Volume)(Bass)(Treble)(Balance)
(Fader)
Volume control/MENU
Rotating this knob, you can adjust VOL/BASS/TREB/BAL/FAD . To select the
functions, press the VOL knob shortly until the desired functions are shown on the
display.
Increase or decrease the volume by turn the VOL knob right or left. These buttons
can be used to adjust the BASS, TREBLE, BALANCE and FADER.
BASS
Press MENU/VOL button(3) one time. Adjust bass level by using MENU/VOL(3)Knob.
TREBLE
Press MENU/VOL button(3) two times. Adjust treble level by using MENU/VOL(3)
Knob
BALANCE
Press MENU/VOL button(3) three times. Adjust sound balance between left and
right speakers by using MENU/VOL(3)Knob .
MENU
MENU/VOL
GENERAL OPERATIONS
MENU/VOL
CD/SD/MMC/USB OPERATIONS
2. Searching Track
•Press AMS twice, then searching track is activated.
•Turn VOL knob to right or left, select the track you want.
•Press VOL knob, the song you selected will start.
3. Searching File Name:
•Press AMS 3 times, then file search is activated.
•Press VOL knob, then the first directory is displayed.
•Turn VOL knob to right or left, you can select the directory you want.
•Press VOL knob again, then the directory is fixed and the first file name is
displayed.
•Turn VOL knob to right or left, you can select the file you want.
•Press VOL knob, then the song you selected will start.
4. Searching Character:
•Press AMS 4 times, then character search mode is activated.
•Press VOL knob, then * character is displayed.
•Turn VOL knob to right or left, you can select the letter you want.
•Press VOL knob longer than 2 sec.
•The song which has same character you selected is displayed.
•Turn VOL knob to right or left, you can select the song you want.
•Press VOL knob, then the song you selected will start.
DSP OFF/ON
MENU/VOL
LOUD OFF/ON DEMO OFF/ON
MENU/VOL
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
GENERAL OPERATIONS
AEM OFF/ON BEEP ON/OFF
MONO/STEREODX/LOCALVOL ADT/LASTAREA EUR/USA
SEEK
DISPLAY
Press DISP button (5) to operate as the conversion of each display mode as follow:
- Time is displayed for 5sec when DISP key is pressed, and it returns to its
previous display ( Folder, File name...) unless DISP key is pressed again.
3) From the clock mode, when DISP Key is pressed for longer than 1sec,
clock mode switches to clock Adjusting mode and the clock display
begins flashing.
or the ENCODER VOLUME.
At this time clock can be changed by pressing (+/-),
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (6).
FLASHING LED
When ACC off ,take out the front panel from main unit that the LED (7) will be flashing.
CD/SD/MMC/USB OPERATIONS
Discs for playback:
This unit can play disc types: CD/CD -R/-RW.
Compatible with formats: CDDA/MP3/WMA.
Loading and ejecting a disc
1. Turn the power on.
2. Insert the disc with the printed side facing upward into the slot.
3. Press EJECT button to eject the disc.
Multi-media card MMC/SD card slot
Support MP3/WMA ID3 format music only. Detach the front panel. Carefully
insert the SD/MMC card into the card slot on the inner panel. Attach the panel.
Unit starts playback automatically.
USB jack
Carefully connect the USB driver to the USB adapter cable and then insert it into
the USB jack on the front panel. Unit starts playback automatically.
USB/SD/MMC notes:
USB functions (flash memory type) MP3 music play.
1. SD/ MMC card support.
2. FAT 12/ FAT 16/ FAT 32 is possible
- FAT 12/16 (dir: 200 support, file:500 support),
- FAT 32 (dir: 200 support, file:500 support).
3. Filename: 32 byte/ Dir name: 32byte.
4. Tag (id3tag ver2.0)
- Title/ Artist/ Album: 32 byte support.
5. Multi card reader not support.
6. USB 2.0 support.
Note:
USB format supports 2.0.
Capacity: up to 16 GB.
SD cards brands: Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP,
Compaq, Sharp, Samsung, etc.
Capacity: up to 16 GB.
MMC cards brands: Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems,
etc.
Capacity: up to 16 GB.
Note: Because of the great variety of products with SD and MMC card slots and
their sometimes quite manufacturer-specific functions the producer can neither
guarantee that all devices will be recognized nor that all operating options that
are possible in theory will actually work.
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
MENU/VOL
DSP OFF/ON
MENU/VOL
GENERAL OPERATIONS
LOUD OFF/ON DEMO OFF/ON
MENU/VOL
AEM OFF/ON BEEP ON/OFF
MONO/STEREODX/LOCALVOL ADT/LASTAREA EUR/USA
SEEK
RADIO OPERATIONS
LOCAL RADIO STATION SEARCH
Press MENU button repeatedly to choose LOCAL(DX).Rotate VOL regulator or
press VOL+/- buttons on the RCto switch between LOCAL and DX.When the
LOCAL function is on the local stations(stations with weak radio)
Press MENU button repeatedly until LOUD ON is displayed.Rotate VOL regulator
on the front panel or press VOL+/VOL- buttons on the RC to select loudness
ON or OFF.
MOno/Stereo control (in FM radio mode)
Press MENU button repeatedly until the display shows STEREO (MONO).Rotate
VOL regulator or press VOL+/- buttons on the RC to switch between STEREO
reception and MONO reception.Improvement of reception of distant stations
can be done by selecting mono mode,which may cut down some reception noise.
AREA USA/EUR SETUP
In Radio mode. Press MENU button for several seconds. LCD will be show from
DSP OFF/ON AREA USA/EUR. At AREA USA/EUR. You can use VOL +/to select the AREA frequency.
CD/SD/MMC/USB OPERATIONS
RADIO OPERATIONS
- Program Scanning
Press AMS button (10) shortly to scan preset station. When the field strength
level is more than the threshold level of stop level, the radio is holding at that preset
number for several seconds with releasing mute, then searches again.
STATION STORING
Press preset button (11~16)
1) RADIO MODE.
M1 ~ M6
- PRESET MEMORY is loaded when key is pressed for less than 1 second.
- PRESET MEMORY is saved when key is pressed for longer than 1 sec.
2) CD MP3 / FLASH MP3 /
PLAY / PAUSE
Press button (11)preset
is activated. During a PAUSE, DISC INDICATOR flashes.
TOP - First son g will play whe n Top key is pressed for lon ge r tha n 0. 5s ec du ring play.
INT
Press preset
button (12): During INTRO ON, INT indicator comes on and
begins playing the first 10sec of each song, until the last song is played. It begins
playing the entire track from where INT started
AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS button (10) for several seconds, the radio searches from the
current frequency and checks the signal strength until one cycle search is finished.
And then 6 strongest stations are stored into the corresponding preset number
button.
BAND SELECTION
At tuner mode, press BAND button (9) to select the desired band. The
reception band will change in the following order:
FM1 FM2 FM3 ( 1) ( 2)AM1 MW AM2 MW
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
CD/SD/MMC/USB OPERATIONS
Discs for playback:
This unit can play disc types: CD/CD -R/-RW.
Compatible with formats: CDDA/MP3/WMA.
Loading and ejecting a disc
1. Turn the power on.
2. Insert the disc with the printed side facing upward into the slot.
3. Press EJECT button to eject the disc.
Multi-media card MMC/SD card slot
Support MP3/WMA ID3 format music only. Detach the front panel. Carefully
insert the SD/MMC card into the card slot on the inner panel. Attach the panel.
Unit starts playback automatically.
USB jack
Carefully connect the USB driver to the USB adapter cable and then insert it into
the USB jack on the front panel. Unit starts playback automatically.
USB/SD/MMC notes:
USB functions (flash memory type) MP3 music play.
1. SD/ MMC card support.
2. FAT 12/ FAT 16/ FAT 32 is possible
- FAT 12/16 (dir: 200 support, file:500 support),
- FAT 32 (dir: 200 support, file:500 support).
3. Filename: 32 byte/ Dir name: 32byte.
4. Tag (id3tag ver2.0)
- Title/ Artist/ Album: 32 byte support.
5. Multi card reader not support.
6. USB 2.0 support.
Note:
USB format supports 2.0.
Capacity: up to 16 GB.
SD cards brands: Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP,
Compaq, Sharp, Samsung, etc.
Capacity: up to 16 GB.
MMC cards brands: Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems,
etc.
Capacity: up to 16 GB.
Note: Because of the great variety of products with SD and MMC card slots and
their sometimes quite manufacturer-specific functions the producer can neither
guarantee that all devices will be recognized nor that all operating options that
are possible in theory will actually work.
Id3 Tag information
This unit supports ID3 tag ver2.0. If an MP3/WMA file has ID3 Tag information,
it will be displayed on the LCD. If there is no ID3 Tag information, nothing will be
shown on LCD. The ID3 Tag information may include File, Folder, Music,Album
or Artist data.
NEXT/PREVIOUS
Rotate the NEXT/PREVIOUS button to choose next or previous track. Press
longer than 1 sec., to choose forward playback or backward playback.
PLAY/PAUSE
Press PAUSE button to pause the playback, press one more time to resume the
normal playback.
INTRO (Preview all Tracks)
When this button is pressed, "INT ON" indication is displayed and the first
several seconds of each track of the disc is played. Press again to stop intro and
listen to track.
REPEAT
When RPT button is pressed, "RPT ON" indication is displayed and playback of
the selected track will be continually repeated until the track repeat mode is
cancelled by pressing RPT button again.
RANDOM
When RDM button is pressed,"RDM ON" indication is displayed and each track
of the disc is played in random instead of normal order. To cancel RANDOM
mode, press RDM button again.
TRACK DOWN/UP SELECT (In case of MP3/WMA files)
-10/5 button: 10 Track down
+10/6 button: 10 Track up
Selection of MP3/WMA files
1.Searching Time
•Press AMS one time, then searching time is activated.
•Turn VOL knob to right or left, select the time you want.
•Press VOL knob, then the select time of the song will play
GENERAL OPERATIONS
MENU/VOL
MENU/VOL
MENU/VOL
LOUD OFF/ON DEMO OFF/ON
DSP OFF/ON
AEM OFF/ON BEEP ON/OFF
MONO/STEREODX/LOCALVOL ADT/LASTAREA EUR/USA
SEEK
Long press SEL key,select AF and TA ON, AF flashing on display
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
CD/SD/MMC/USB OPERATIONS
2. Searching Track
•Press AMS twice, then searching track is activated.
•Turn VOL knob to right or left, select the track you want.
•Press VOL knob, the song you selected will start.
3. Searching File Name:
•Press AMS 3 times, then file search is activated.
•Press VOL knob, then the first directory is displayed.
•Turn VOL knob to right or left, you can select the directory you want.
•Press VOL knob again, then the directory is fixed and the first file name is
displayed.
•Turn VOL knob to right or left, you can select the file you want.
•Press VOL knob, then the song you selected will start.
4. Searching Character:
•Press AMS 4 times, then character search mode is activated.
•Press VOL knob, then * character is displayed.
•Turn VOL knob to right or left, you can select the letter you want.
•Press VOL knob longer than 2 sec.
•The song which has same character you selected is displayed.
•Turn VOL knob to right or left, you can select the song you want.
•Press VOL knob, then the song you selected will start.
TA appears on display.
SEL
3
Press SEL key,PTY flashing on display when select PTY.
Press SEL enter TA,
MU
BND
2/INT 3/RPT 4/RDM1/
MEN U
DISP
MOD E
AMS
GENERAL OPERATIONS
FRONT PANEL LAYOUT
1. Power / Mode / Next / Previous Button
3. Menu / Volume Button
5. Display Button
11. Play / Pause & Preset Button 1
2. Release Button
12. Intro & Preset Button 2
6. LCD Display
13. Repeat & Preset Button 3
10. Automatically memory storing
14. Random & Preset Button 4
15. Preset Button 5
16. Preset Button 6
19. USB connecter
8. Reset Button
17. Eject knob
18. CD Slot
7. Flashing LED
20. SD/MMC Slot
21. AUX IN JACK
18
17
20
7 8
2
3
4
5
19
6
9
11 12 13 14 15 16
21
10
1
9. Band/ switch /ID3 select
4. Mute / Button
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
BLUETOOTH
1.Pairing connect.
Turn on car unit, put your mobile near the unit, activate your mobile bluetooth
function.Soon the phone will find the new bluetooth device "CAR AUDIO" .
Input the pairing password “8888” and clik OK. The phone will prompt the
matching successful.When the pairing connect is successful,on the LCD, it shows
BT ON, and the bluetooth logo “ ”will stop blinking .Then you may perform the
bluetooth operation.
REMARK:depend on bluetooth mobile, the bluetooth system support “HSP” “HFP”
“A2DP” and AVRCP bluetooth profile.
2.Handsfree phone service
If your mobile phone have matched with the unit. You can dial calls out through your
mobile phone. It will turn to unit automatically when calling come in and the calling
phone number will indicat on the LCD screen.
-Press the “BAND” button shortly to accept the call .Then you can talk with the
other party through the mic on the panel.
-Press “MUTE” button shortly to reject the call when calling come in.
-Press “MUTE” button shortly to hang up after you finish the talk.
3.Advance Audio distributing profile(A2DP) playing.
Through mobile and unit A2DP connected, the music playing in mobile can turn
to the unit audio system play. Press button “ ”and “ ” in the panel can select
the music track.
-Press “ ” button shortly to pause the music playing.
-Press “BAND”(mode) longly to temporarily discommect the bluetooth.
-Press “BAND”(mode) button longly again to reconnect the bluetooth.
· MP3 is short for MPEG Audio Layer 3 and refers to an audio compression
technology standard.
· This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs.
· The unit can read MP3 files written in the format compliant with ISO 9660.
However it does not support the MP3 data written by the method of packet write.
· The unit can not read an MP3 file that has a file extension other than “.mp3”
· If you play a non- MP3 file that has the “.mp3” extension, you may hear some
noise.
· In this manual, we refer to what are called “MP3 file” and “ folder” in PC
terminology as “ track ” and “ album ”, respectively.
· Maximum number of directory level is 8, including the root directory. Maximum
number of files and folders per disc is 256.
· The unit may not play tracks in the order of Track numbers.
· The unit plays only the audio tracks if a disc contains both audio tracks and
MP3 files.
· When playing a disc of 8 kbps or “VBR”, the elapsed playing time in the display
window will not be correct and also the intro play may not function properly.
“ VBR ”:Variable Bit Rate.
· The unit supports the playback of WMA files. The playback of ID3 tags for WMA
format is not guaranteed, it depends on versions and availability of Cyrillic
alphabet.
· WMA (Windows Media Audio) -music data compression format, created by
Microsoft Corporation. This format uses coding algorithm for compression of
initial audio-record, greatly decreasing the file size, but, saving the good sound
quality even when the bit rate is low (for example, 64 Kbit/s).
· Remember that the unit may not play the tracks in order they are written on disc.
4.Phone number book.
This bluetooth system can automatically store incoming call numbers, up to
10 phone numbers.
-Press “MUTE”(mode) button longly to enter the phone number book and press
VOL button to look up the phone number.
-Press “BAND” button once can call out you desired phone number.
5. Interrupt bluetooth connection/reconnection.
Pressing the “BAND” button shortly to interrupt the bluetooth connection when
your are talking a call and the voice can turn to mobile speaker.
Press “BAND” button again to reconnection.
NOTE:Different mobile phone have different responses.We do not guarantee all the
operation of connectable devices.
6. How to delete stored phone number?
You jus t can store ten number of missed ,rejected and ANS under separately,
and the first number will auto deleted when the 11th number calling
7. How to use “Missed”,”Rejected””Auto ANS” Functions.
Press MUTE button for 3 seconds to enter into REVIEVED /MISSED/REJECTED/
ANTO .ANS .Turn VOL button for choosing the telephone number.
Notes on creating your own CD-R or CD-RW containing MP3 files:
·
To enjoy high quality sound, we recommend converting to MP3 files with a
sampling frequency of 44.1 kHz and a fixed bit rate o f 128 kbps.
·
DO NOT store more than 256 MP3 files per disc.
·
For ISO 9660 - compliant format, the maximum allowable depth of nested
folders is 8, including the root directory (folder).
·
When CD-R disc is used, playback is possible only for discs, which have been
finalized.
·
Make sure that when MP3 CD-R or CD-RW is burned that it is formatted as a
data disc and NOT as an audio disc.
·
You should not write non-MP3 files or unneeded folders along with MP3 files
on the disc otherwise it takes a long time until the unit starts to play MP3 files.
·
With some CD-R or CD-RW media, data may not be properly written depending
on its manufacturing quality. In this case, data may not be reproduced correctly.
High quality CD-R or CD-RW disc is recommended.
·
Up to 16 characters are displayed for the name of an Album or a Track. ID3TAG
version 1.x is required.
·
Note that the unit may not play Tracks in the order that you wrote them to the
disc.
INPUT THE SD CARD
The SD oblique angle keeps
rightward exposure, put into
the SD slot and press it again
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
2. Insert fingers into the groove in the
front of fram e and pul l out to rem ove
the fram e. (When reatt achi ng the
frame, point the side with a groove
dow nwards and at tach it.)
3. Leve r
Insert the leve rs sup pl ied with the
uni t int o the grooves at both sides of
the uni t and show n in fi gure unti l they
click. Pull in g th e levers makes possible
to remove the unit fro m th e dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit
Fastening the unit to the factory
radio mounting bracket:
1. Select a position where the screw
holes of the bracket and the
screw holes of the main unit
become aligned (are fitted), and
tighten the screws at 2 places on
each side. Use either truss screws
(5 x 5mm) or flush surface screws
(4 x 5mm)
2. Screw
3. Dashboard or Console
INSTALLATION
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
2
3
2
2
1
3
(Fig. 3)
Removing the unit
1
2
3
4
5
6
7
(Fig. 2)
RCD 120BT(/B) • MANUAL RCD 120BT(/B) • MANUAL
SPECIFICATION
General
Power Supply Requirements:
Impedance:
Load
Maximum Output Power:
Chassis Dimensions: 178 x 163x 50mm (W x D x H)
Current Drain:
10A
DC 14. 4V“ ”, Negative Ground
4 ohms
75W x 4( CH)
Tone Controls
Bass (at 100Hz):
Treble (at 10K):
+10dB / -10dB
+10dB / -10dB
CD Player
Signal to Noise Ratio:
Channel Separation:
Frequency Response:
More than 60dB
More than 60dB
20Hz - 20KHz
FM Radio
Frequency Coverage (MHz):
87.5 - 108MHz
Cleaning the CD
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device
may be damaged.
Note: If there is already a CD in the CD slot , do not try to insert a second
CD. This may damage the device.
Always hold CDs by the edge. In order to keep the CD clean do not touch
the surface. Pull out the CD as follows.
BEFORE PLAYING DISCS
10.7MHz
IF :
Sensitivity (S/N-30dB):
Stereo Separation:
12dBu
>30dB
Remarks:
Specifications subject to change without notice
Bluetooth Freq range: 2402-2480 Mhz
Max e.r.p: <100mW/20dBm
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heating.
Do not leave CDs in a car if it parked in direct sunlight as that will lead to
a considerable rise in the temperature inside the car.
Note: Do not use any solvents such as petrol or thinning agents. Commercially
available cleaning substances of antistatic spray will damage the device.
RCD 120BT(/B) • MANUAL
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the
problems persist after checklist has been made, consult your nearest service
dealer
Symptom
No Power
CD Cannot Be
Loaded or Ejected
No Sound
Causes Solution
The car ignition key not
been switched on
The fuse is blown
A CD is already inside the
player slot
Inserting the CD in reverse
direction
The CD is extremely dirty or
defected
Temperature inside the car is
too high
Condensation
Volume is at minimum
Wiring is not properly
connected
If the power supply is properly
connected to the car accessory
terminal, switch the ignition
key to ACC
Replace a new fuse
Remove the CD from the player
and insert the new one
Insert the CD with the label
facing up
Clean the CD or try to play
a new one
Cool off until the ambient
temperature return to normal
Leave the player off for an
hour or so and try again
Adjust volume to desired level
Check wiring connection
Sound Skipping
The Operation Keys
Do Not Work
The Radio or
Automatic Selection
Does Not Work
The installation angle is more
o
than 30
CD is extremely dirty or
Defected
The built-in microcomputer is
not operating properly due to
Interference
The antenna cable is not
connected correctly
The signals are too weak
Adjust the installation angle to
less than 30
Clean the CD or try to play
a new one
Press the RESET button or
reinstall the front panel
properly
Connect the antenna cable
correctly
Select the station manually
o
WWW.CALIBER.NL
CALIBER EUROPE BV • Kortakker 10 • 4264 AE Veen • The Netherlands
Loading...