Burkert 2300 Series, 2300 A 25 M PTFE VA Quick Start Manual
Type 2300
2/2-way angle-seat control valve
Quickstart
English
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert Werke GmbH & Co. KG, 2013 - 2018
Operating Instructions 1802/03_EU-EN_00810317 / Original DE
Typ 2300
Quickstart
1 QUICKSTART ........................................................................ 3
2 SYMBOLS ............................................................................. 4
3 INTENDED USE .................................................................... 4
4 BASIC SAFETY INSTRUCTIONS .......................................... 5
5 GENERAL INFORMATION .................................................... 6
6 STRUCTURE AND FUNCTION ............................................. 7
7 TECHNICAL DATA ................................................................. 8
8 INSTALLATION .................................................................... 10
9 PACKAGING, TRANSPORT, STORAGE ............................. 17
1 QUICKSTART
The operating instructions describe the entire life cycle of the device.
Keep these instructions in a location which is easily accessible
to every user and make these instructions available to every new
owner of the device.
Important Safety Information!
Read Quickstart carefully and thoroughly. Study in particular
the chapters entitled “Basic Safety Instructions” and “Intended
use”.
▶ Quickstart must be read and understood.
Quickstart explains, for example, how to install and start-up the
device.
A detailed description of the device can be found in the operating instructions for Type 2300.
The operating instructions can be found on the Internet at:
www.burkert.com
1.1 Denition of term / abbreviation
In these instructions, the term “device” always refers to the
angle-seat control valve type 2300.
The abbreviation “Ex” used in these instructions always stands
for “explosion-protected”.
english
3
Typ 2300
Symbols
2 SYMBOLS
DANGER!
Warns of an immediate danger!
▶ Failure to observe the warning may result in a fatal or serious
injury.
WARNING!
Warns of a potentially dangerous situation!
▶ Failure to observe the warning may result in serious injuries or
death.
CAUTION!
Warns of a possible danger!
▶ Failure to observe this warning may result in a moderately
severe or minor injury.
NOTE!
Warns of material damage!
Important tips and recommendations.
Refers to information in these operating instructions or in
other documentation.
3 INTENDED USE
Non-authorized use of the globe valve Type 2106 may be a
hazard to people, nearby equipment and the environment.
▶ The device is designed for the controlled ow of liquid and
gaseous media.
▶ In the potentially explosion-risk area the globe valve type
2106 may be used only according to the specication on
the separate Ex type label. For use observe the additional
information enclosed with the device together with safety
instructions for the explosion-risk area.
▶ Devices without a separate Ex type label may not be used in
a potentially explosive area.
▶ The admissible data, the operating conditions and condi-
tions of use specied in the contract documents, operating
instructions and on the type label are to be observed during
use. These are described in the chapter entitled “7 Technical
data”.
▶ Protect device from damaging environmental inuences (e.g.
radiation, humidity, steam, etc.). If anything is unclear, consult
the relevant sales oce.
▶ The device may be used only in conjunction with third-party
devices and components recommended and authorized by
Bürkert.
▶ Correct transportation, correct storage and installation and
careful use and maintenance are essential for reliable and
faultless operation.
▶ designates instructions for risk prevention.
→ designates a procedure which you must carry out.
4
english
Typ 2300
Basic Safety Instructions
4 BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any
• contingencies and events which may arise during the installation,
operation and maintenance of the devices.
• local safety regulations; the operator is responsible for observing
these regulations, also with reference to the installation personnel.
DANGER!
Risk of injury from high pressure in the equipment or device!
▶ Before working on equipment or device, switch o the pres-
sure and deaerate or drain lines.
Risk of injury from electric shock (when electrical component
installed).
▶ Before reaching into the device, switch o the power supply
and secure to prevent reactivation!
▶ Observe applicable accident prevention and safety regulati-
ons for electrical equipment!
WARNING!
Risk of injury when opening the actuator!
The actuator contains a tensioned spring. If the actuator is
opened, there is a risk of injury from the spring jumping out!
▶ The actuator must not be opened.
Risk of injury from moving parts in the device!
▶ Do not reach into openings.
Danger due to loud noises.
▶ Depending on the operating conditions, the device may generate
loud noises. More detailed information on the likelihood of loud
noises is available from the relevant sales oce.
▶ Wear hearing protection when in the vicinity of the device.
CAUTION!
Risk of burns!
The surface of the device may become hot during long-term
operation.
▶ Do not touch the device with bare hands.
Leaking medium when the packing gland is worn.
▶ Regularly check relief bore for leaking medium.
▶ If the media is hazardous, protect the area surrounding the dis-
charge point against dangers.
General hazardous situations.
To prevent injury, ensure:
▶ That the system cannot be activated unintentionally.
▶ Installation and repair work may be carried out by authorized
technicians only and with the appropriate tools.
▶ After an interruption in the power supply or pneumatic
supply, ensure that the process is restarted in a dened or
controlled manner.
▶ The device may be operated only when in perfect condition
and in consideration of the operating instructions.
▶ Observe the safety regulations specic to the plant for applica-
tion planning and operation of the device.
english
5
Typ 2300
General Information
▶ The plant operator is responsible for the safe operation and han-
dling of the plant.
▶ The general rules of technology apply to application planning
and operation of the device.
To prevent damage to property of the device, ensure:
▶ Supply the media connections only with those media which are
specied as ow media in the chapter entitled “7 Technical data”.
▶ Do not put any loads on the valve (e.g. by placing objects on
it or standing on it).
▶ Do not make any external modications to the valves. Do not
paint the body parts or screws.
▶ The exhaust air may be contaminated with lubricants in the
actuator.
▶ Do not transport, install or remove heavy devices without the aid
of a second person and using suitable auxiliary equipment.
5 GENERAL INFORMATION
5.1 Contact addresses
Germany
Bürkert Fluid Control Systems
Sales Centre
Christian-Bürkert-Str. 13-17
D-74653 Ingelngen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: info@burkert.com
International
Contact addresses are found on the Internet under:
www.burkert.com
5.2 Warranty
The warranty is only valid if the device is used as authorized in
accordance with the specied application conditions.
5.3 Information on the internet
The operating instructions and data sheets for Type 2300 can be
found on the Internet at: www.burkert.com
6
english
Loading...