BT DECOR 110 User Manual

To delete stored numbers

Lift the handset.
Press the STORE button. The call

indicator light will flash.
Press the memor y location

number (0-9) or (M1

, M2, M3)

under which you have stored the
number you wish to delete.

Press the STORE button.
You will hear a confirmation tone.
Replace the handset.

Alternatively, any existing
number stored in the Quickdial
or One-Touch memories can be
overwritten by entering a new
number under the same memory
location. Simply follow the
instructions under the storing
numbers sections previously shown.

BT Accessories and
Replacement Items

For a full range of accessories and
replacement items for BT
products please call 0870 240 5522,
or visit:

Wall
mounting

1. Locate lugs and mount the
plinth provided into the holes
under the base unit as shown.

2. Swing the plinth down to clip
into the top hole.

3. Drill 2 holes, 25mm deep using
a 3mm drill, for the screws
provided, using the template.
Ensure that you do not drill into
any hidden wiring or pipes.
Insert the wall plugs provided
and then insert a screw into each
hole. Leave 2-3mm between the
head of the screw and the wall.

4. Position the product onto the
screws.

5. Drop down to secure.

R&TTE Directive

Hereby, Suncorp Technologies Ltd,
declares that this BT Decor 110
is in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.

The Declaration of Conformance
for the BT Decor 110 is published
on the website
http://www.suncorptech.com/bt

Note

You can mix manual and
memory dialling as required, for
example, you can dial the area
code 020 8304 from the memory
and then complete the number
manually.

Note

If any error occurs in the storing
mode you will hear three short
beeps, then the product will
return to talk mode.

If you unplug your BT Decor 110
the numbers stored in the
memory will be saved. However,
the last number redial memory
will be lost.

General information

Guarantee

Your BT Decor 110 is guaranteed
for a period of 12 months from the
date of purchase.

Subject to the terms listed below
the guarantee will provide for the
repair of, or at BT’s or its agent’s
discretion the option to replace the
BT Decor 110, or any component
thereof, which is identified as
faulty or below standard, or fails as
a result of inferior workmanship
or materials. Products over 28 days
old from the date of purchase
may be replaced with a refurbished
or repaired product.

The conditions of this
guarantee are:

• The guarantee shall only apply
to defects that occur within the
12 month guarantee period.

• Proof of purchase is provided.

• The equipment is returned to
the point of purchase.

• This guarantee does not cover
any faults or defects caused by
accidents, misuse, fair wear
and tear, neglect, tampering
with the equipment, or any
attempt at adjustment or repair
other than by approved agents.

• This guarantee does not affect
your statutory rights.

Within the 12 month guarantee
period:

In the unlikely event of a defect
occurring, please retur n the
product, with the receipt, to the
place of purchase.

Outside of the 12 month
guarantee period:

If your product needs repair after
the guarantee period has ended,
the repair must meet the approval
requirements for connection to the
telephone network. We recommend
that you contact BT’s approved
repair agent, TecLogic on 01672
564444 or a local qualified repairer.

If you have to return your
BT Decor 110

Pack the unit securely, preferably
in the original packaging. All parts
must be returned. We cannot take
responsibility for goods damaged
in transit.

Technical information

How many telephones can you
have?

All items of telephone equipment
have a Ringer Equivalence
Number (REN), which is used to
calculate the number of items
which may be connected to any
one telephone line. Your
BT Decor 110 has a REN of 1.
A total REN of 4 is allowed, if the
total REN of 4 is exceeded, the
telephones may not ring. With
different telephone types ther e is
no guarantee of ringing, even
when the REN is less than 4.

Switchboard compatibility

This product is intended for use
within the UK for connection to
the public telephone network and
compatible switchboards, which
support tone dialling and time
break recall. If in doubt please
consult your service pr ovider.

Offices worldwide

The telecommunications services described in
this publication are subject to availability and
may be modified from time to time. Services
and equipment are provided subject to British
Telecommunications plc’s respective standard
conditions of contract. Nothing in this publication
forms any part of any contract.

© British Telecommunications plc 2003.
Registered Office: 81 Newgate Street, London
EC1A 7AJ.
Registered in England No. 1800000.
BT Decor 110 Issue 2 (8/03) 1
Designed by the Art & Design Par tnership
Limited.
Printed in China.

4

5

1

2

69mm

BT Decor 110

CORDED TELEPHONE

This product is intended
for connection to analogue public switched
telephone networks and private switchboards
in the United Kingdom.

Making and ending calls

To make a call

Lift the handset and wait for the
dial tone.

Dial the telephone number.

To end a call

Replace the handset.

To receive a call

When the telephone rings the call
indicator light will also flash to
indicate that there is an incoming
call. Simply pick up the handset.

To redial the last number
called

Lift the handset.
Press the REDIAL button.
The last number called is dialled.
A redial number can be no longer

than 32 digits.

Secrecy

When on a call you can talk to
someone in the same room,
without your caller hearing.

To switch secrecy on and off

During a call press and release the
SECRECY button.

The call indicator light will flash to
show that secrecy is on.

Your caller will be put on hold.

You can now talk to someone in
the room without your caller
hearing you.

Press and release the SECRECY
button again to return to your
caller.

To adjust the ringer volume

There are 3 volume settings to
choose from: HIGH, LOW or OFF.
The default setting is HIGH.

Lift the handset and press the
STORE button. The call indicator
light will flash.

Press the

✱

button.

Press either, 1 for HIGH, 2 for
LOW or 3 for OFF.

Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
(If the ringer is set to OFF, the call

indicator light will still flash to
indicate someone is calling you.)

To set the ringer pitch

The ringer pitch can be set to
High or Low. The default setting
is High.

Lift the handset and press the
STORE button. The call indicator
light will flash.

Press the #button.
Press either, 1 for HIGH or 2 for

LOW.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.

One-Touch memories

You can store your three most
frequently used telephone numbers
in the One-Touch memories
(M1, M2 or M3). Please note that
the number can be no longer than
18 digits.

To store a One-Touch number

Lift the handset.
Press the STORE button. The call

indicator light will flash.
Press the memor y location number,

(M1

, M2, M3), under which you

want to store the number.
Enter the telephone number you

want to store including the area
code if applicable.

Press the STORE button.
You will hear a confirmation tone.

Replace the handset.

To dial a One-Touch number

Lift the handset and wait for the
dial tone.

Press the memor y location
number, (M1

, M2, M3), under

which the number is stored.
The number is dialled

automatically.

To insert a pause in a memory
number

Sometimes you may need to enter
a pause when storing a number,
e.g. with an overseas number you
may need to enter a pause after
storing the international code.

Press the REDIAL button in the
place where you want to enter a
pause.

When you dial the number your
BT Decor 110 will automatically
insert the pause where you
stored it.

Quickdial memories

You can store a further 10 telephone
numbers in the Quickdial memories.
Please note that the numbers can
be no longer than 18 digits long.

To store a number in the
Quickdial memory

Lift the handset.
Press the STORE button.

The call indicator light will flash.
Press the memor y location

number between 0 and 9 under
which you want to store the
number.

Enter the telephone number you
want to store including the area
code if applicable.

Press the STORE button.
You will hear a confirmation tone.

Replace the handset.

To dial a number in the
Quickdial memory

Lift the handset and wait for the
dial tone.

Press the QUICKDIAL button.
Press the memor y location

number between 0 and 9, under
which the number is stored.

The number is dialled automatically.

Note

Whilst storing a number in the
memory you can cancel the
operation by replacing the handset
on the cradle.

Setting up

Plan the location of your
BT Decor 110.

Situate your BT Decor 110 close
enough to a phone socket so that
the line cord will reach.

You can wall-mount your product,

see back page.

1. Plug your BT Decor 110
into the telephone socket.

Your BT Decor 110 is now ready
for use.

Using the telephone

At a glance

Quickdial button

Allows you to dial up to ten numbers
stored in the Quickdial memor y at the
touch of two buttons.

One-Touch memory buttons
(M1, M2, M3)

Allows you to store and
automatically dial up to three
numbers at the touch of one
button.

Store button

Use to store numbers in the memor y
and to change the ringer and pitch
volume.

Call indicator light

Flashes to indicate an incoming call.
Also flashes when storing numbers,
using secrecy or setting the ringer.

Redial/Pause button

Redials the last number called.
Also, press to enter a pause when
storing a number in the memory.

Secrecy button

Lets you talk to someone in the same
room without the person you are
calling hearing you.

Recall button

For use with a switchboard/PBX and
BT Calling Features. Please contact
your switchboard supplier for more
information. For more information on
BT ’s Calling Features please call

Freefone 0800 800152

Handset hook

Keeps the handset in place when the
BT Decor 110 is wall mounted.

See back page for more information.

Revolve the handset catch on the
base unit. The handset will now be
able to rest on the hook when
wall-mounted.

Safety information

General

Simply clean your BT Decor 110 with a
damp (not wet) cloth, or an anti-static
wipe. Never use household polish as this
may damage the product. Never use a
dry cloth as this may cause static shock.

Do not open the BT Decor 110. This
could expose you to high voltages or
other risks.

Environmental

Do not expose to direct sunlight.

We recommend that you do not place the
product on antique/veneered wood to
avoid damage.

Do not stand your product on carpets or
other surfaces which generate fibres, or
place it in locations preventing free flow
of air over its surfaces.

Do not submerge any part of your
product in water and do not use it in damp
or humid conditions, such as in bathrooms.

Do not expose your product to fire,
explosive or other hazardous conditions.

Note

There is a quickdial memory
label on your telephone. Lift the
plastic plate up and you can
write on the label to keep a
record of which memory location
number you have used for each
telephone number.

Note

During all storing operations the

call indicator light will flash.

BT Decor 110

Quickdial

B

A

C

E

D

1

4

P

7

F

2

3

H

G

K

J

I

L

N

M

O

Store

5

6

Q

R

U

T

V

X

S

W

Y

Z

8

0

Redial

R

9

e

r

c

c

e

y

S

S