Bryston 6B SST User Manual
6BSST
POWER AMPLIFIER
OWNER’S MANUAL
6BSST THREE CHANNEL POWER AMPLIFIER
Table of Contents
General Introduction Page 1
Instalation and Ventilation
Rear Panel Input Settings/Connections Page 2
Setting Input Selector Switch
Balance Input Connector Configuration
Setting Polarity
Setting Input Sensitivity
Output Binding Posts and Polarity Page 3
Front Panel Description Page 4
LED Indicators (Power-up Sequence)
LED Indicators (Operating Conditions)
Power Control Panel Page 5
Master Curcuit -Breaker
AC Power Input
Local/Auto Switch
Local/External Switch
Rack Mounting Instructions Page 6
Individual Module Removal
Channel Fuse Type/Location
5.1 Typical Home Theatre Setup Page 7
Block Diagram of the 6BSST Page 8
Typical Performance Graphs Page 9-12
Technical Specifications Page 13
Important Warranty Information Back Cover
6BSST THREE CHANNEL POWER AMPLIFIER
Introduction
Thank you for choosing the 6BSST Three Channel Power Amplifier.
Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consider
you, our customer, to be Bryston’s most important resource, and your opinion is very much appreciated.
Description
The 6BSST is a modular design 3 x 300W per channel audio power amplifier. Each channel selects a balanced or single
ended input. Each channel selects a gain of 29dB(1v), 23dB(2v) or 17dB(4v). Each channel input may be operated inverted or non-inverted operation(0 or -180 degrees). The power up of the 6BSST may be controlled by remote control voltage.
The 6BSST includes ‘soft start’ power control circuitry to eliminate high inrush currents when A/C power is applied.
Warranty ( see back page for details )
Shipping Box & Packing Material
Please keep the original shipping box and all packing material. This will ensure the amplifier is protected in future transport.
In the unlikely event you have a problem and must return it for service you must use the proper packing material. Ship the
amplifier only in the original packing material, as the unit is not insurable by carriers otherwise.
Installation ( see rack mounting section if applicable )
Ventilation. The most important installation consideration is ventilation. The 6BSST is a convection-cooled amplifier.
Unrestricted air-flow across its heat sinks is a must. For this reason do not install anything directly above it. Allow 3.5’
(2u) to 5” (3u) inches of space above and to the sides of this amplifier. Do not install directly above other heat generating
equipment. Should your instillation conditions be constricted, then additional forced air-cooling may be necessary. Bryston
can provide an optional fan package if required. Any 6BSST channels thermally shutting down during operation indicates
insufficient cooling, and a remedy must be found for cooling the amplifier. Provide a minimum 6” space to the rear of the
6BSST for ventilation and dressing cables to and from the amplifier.
Never operate the 6BSST in a vertical position.
Wiring the 6BSST ( also see rear panel description )
Speaker wires should be as short as practical. Use quality wire, and if runs are more than 3 meters use at least 12 gauge
wire. The speaker binding posts will accept wire up to 3 gage in size. Bryston can custom build cables for your application.
A/C power
Before plugging in the power cord be sure your 6BSST is specified for the correct a/c voltage for your locality. The voltage
is listed to the right of the power input connector. The circuit feeding the 6BSST should be sufficient so as not to cause the
circuit breaker to trip. Note: the 6BSST when operated with all channels at maximum power into 4 ohm loads, can consume
all the available power in a normal household circuit, therefore a dedicated electrical circuit may be necessary with this
situation. Never lift the safety ground to the amplifier or remove the ground pin from the plug.
Power line conditioners will not improve the 6BSST performance, in fact most of the time they restrict the flow of cur-
rent in the power line to the amplifier, reducing performance at high output levels.
1
6BSST THREE CHANNEL POWER AMPLIFIER
Rear Panel Input / Output Connections
1. Input Select Switch.
Each 6BSST channel gives the user the option of switching between
either balanced input or single ended input.
2. Balanced Input connector. ( Imp. 20k )
This input connector accepts standard ‘XLR’ or 1/4” TRS .
Use quality, 100% shielded cables with gold plated connectors.
‘XLR’ type
‘TRS’ type
‘RCA’ type
3. Single Ended Input. ( Un-balanced input ) ( Imp. 50k )
This input connector accepts standard ‘RCA’ or ‘Phono’ connectors.
Use quality, 100% shielded cables with gold plated connectors.
Balanced input Vs Single ended input:
The balanced input requires a balanced pre-amp source. Balanced
systems provide noise protection from external electrical interference,
so cable length can be very long (50m or longer ).
The single ended or unbalanced input is provided for pre-amps without balanced output. Single-ended cables should be
kept to 20’ (7m) or less. In general never use longer cables than necessary, never coil excess cable length, and run signal wires away from AC power or speaker cables.
4. Polarity Switch ( 0 or -180 degrees)
Each 6BST channel gives the user the option of inverting the polarity of the input signal -180 degrees.
Polarity inversion is application specific. The normal operating position is 0 degrees.
5. Input Sensitivity (Gain) Switch.
The optimum gain setting will depend upon the source pre-amp operating level, and or personal preference.
The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source.
This is the home theatre setting for single ended or un-balanced operation.
The 1v setting provides the most amplifier gain - 29 dB. (1v in = 100w @ 8 ohms.) (noise -112 dB)
A signal level of 1.7v at the input is required to deliver 300W into 8 ohms (rated output).
The 2v setting is used when the sources output is actively Balanced.
This is the home theatre setting for balanced operation Or use this setting with any systems where
the volume control rotation is limited to the bottom half of the control or less.
The 2v setting provides an amplifier gain - 23 dB. ( 2v in = 100w @ 8 ohms.) ( noise -115 dB )
A signal level of 3.4v at the input is required to deliver 300W into 8 ohms (rated output).
Fig 1
The 4v setting is used when the source pre-amp has a high output level, or in ultra sensitive systems where
the volume control rotation range is still limited when using the 2v setting.
Some pre-amps may be unable to deliver enough level to use this setting.
The 4v setting provides an amplifier gain - 17 dB. ( 4v in = 100w @ 8 ohms.) ( noise -118 dB )
A signal level of 6.8v at the input is required to deliver 300W into 8 ohms (rated output).
The noise is referenced in dB below rated output of 300 watts. Different input configurations result in slightly different
2
6BSST THREE CHANNEL POWER AMPLIFIER
6. Output binding posts & polarity.
The RED binding post is connected to the amplifier output. Connect to this post the (+) terminal on the loudspeaker.
The BLACK binding post is connected to signal ground. Connect to this post the (-) terminal on the loudspeaker.
When the polarity switch is set for 0 degrees (normal operation ) the output at the RED binding post is in phase with the
input signal.
When the polarity switch is set for 180 degrees (inverted operation) the the output at the RED binding post is 180 degrees
out of phase with the input signal.
The Output binding posts provide three different interconnect options. Combinations may be used when bi-wiring. See figure 2 below. Cables should be kept as short as practical and should never be terminated with connectors that may become
confused for AC power connectors. Cables should be dressed away from input and power cables.
1. Banana plugs offer a quick disconnect option. Before inserting a banana plug into the binding post be sure to tighten the
post nut to avoid rattling and to provide full insertion of the banana plug. Gold plated locking banana plugs are available
from Bryston.
2. Spade lugs provide high contact area and secure fastening. Lugs should be gold plated. See diagram for details.
Post diameter is 5/16’ ( 8mm ),lug width 5/8” (16 mm). Gold plated spade lugs are available from Bryston.
3. Stripped bare wire up to 3 gauge can be inserted through the hole in the binding post and held in place by tightening
the post knob. Additional tightening pressure can be achieved using a coin in the slots of the knob. Do not over tighten
or the binding post may become damaged. Note that copper wire is malleable and may require further tightening after the
initial installation.
Fig 2
2
Spade lug dimensions
3
5/16”
5/8”
1
Coin
7. Rear Handle (Page 2 Fig 1)
The handle on each channel is to protect the connectors and removal of the channel from the chassis.
This handle should never be used to carry the 6BSST. Use only the front panel handles for carrying the 6BSST,
or lift from the sides of the chassis if not equipped with front panel handles.
3
Loading...