Brother DCP-J515W, DCP-J715W Setup Guide

Download

Quick Setup Guide

WARNING

DCP-J515W

Start Here

Before you can use the machine, please read this Quick Setup Guide for the correct setup and installation.

WARNING

CAUTION

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injuries.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries.

DCP-J715W

Unpack the machine and check the components

Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep these bags away from babies and children.

 Most of the illustrations in this Quick Setup Guide show the DCP-J515W.

a Remove the protective tape and film covering the machine,

and also from the LCD.

b Remove the green protective part a by lifting the front of the

machine and then pulling down on the packing part.

c Remove the plastic bag b containing the ink cartridges from on top of

the paper tray.

CEE-ENG Version 0

Attachment of the cover

IMPORTANT

of the control panel

a Attach the cover of the control panel to the

machine.

Load plain A4 paper

a Pull the paper tray completely out of the

machine.

b Lift the output paper tray cover. c With both hands, gently press and slide the

paper side guides a and then the paper length guide b to fit the paper size.

Make sure that the triangular marks c on the paper side guides a and paper length guide b line up with the mark for the paper size you are using.

d Fan the stack of paper well to avoid paper jams

and misfeeds.

e Check that the paper is flat in the tray.

DO NOT push the paper in too far.

f Gently adjust the paper side guides to the

paper with both hands.

g Close the output paper tray cover. h Slowly push the paper tray completely into the

machine.

i While holding the paper tray in place, pull out

the paper support until it clicks, and then unfold the paper support flap.

Connect the power cord

WARNING

CAUTION

IMPORTANT

Note

Install the ink cartridges

DO NOT connect the USB cable yet (if you are using a USB cable).

a Connect the power cord.

The machine must be fitted with an earthed plug.

The Warning LED on the control panel will stay on until you have installed the ink cartridges.

Choose your language

If ink gets in your eyes, wash them out with water at once, and if irritation occurs consult a doctor.

a Make sure that the power is turned on. b Open the ink cartridge cover.

c Remove the green protective part. d Unpack the ink cartridge.

Press a or b to choose your language and press OK.

b Press a or b to choose Yes or No and press

OK.

Make sure you install the Inbox Ink Cartridges included with your machine first.

f Take care to match the colour of the lever with

the cartridge colour.

g Install each ink cartridge in the direction of the

arrow on the label.

h Gently push the ink cartridge until it clicks. After

all the ink cartridges are installed close the ink cartridge cover.

Check the print quality

a When the preparation process has finished, the

LCD shows Set Paper and Press Start.

Press Colour Start.

b Check the quality of the four colour blocks on

the sheet. (black/yellow/cyan/magenta)

c If all lines are clear and visible, press (Yes)

to finish the quality check and go to step 8.

If you can see missing short lines, press

(No) and follow the steps on the LCD.

Set the date and time

a Press Menu. b Press a or b to choose Initial Setup.

Press OK.

c Press a or b to choose Date&Time.

Press OK.

d To enter the last two digits of the year, press a,

b, d or c to select a number and press OK. To

set the year, press a, b, d or c to select and press OK.

e Repeat for month/day/time in 24-hour format. f Press Stop/Exit.

Note

Choose your connection type

Windows

For USB interface cable

Windows®, go to page 6 Macintosh, go to page 8

For Wired Network (DCP-J715W only)

Windows®, go to page 10 Macintosh, go to page 12

For Windows Server® 2003/2003 x64 Edition/2003 R2/2003 R2 x64 Edition/2008/2008 R2, see the Network User’s Guide on the documentation CD-ROM.

USB Wired Network

Macintosh

Windows

Macintosh

Wireless Network

For Wireless Network

Windows® and Macintosh, go to page 14

USB

IMPORTANT

For USB interface users (Windows Windows Vista

2000 Professional/XP/XP Professional x64 Edition/

/Windows® 7)

Windows

Before you install

a Make sure that your computer is ON and you

are logged on with Administrator rights.

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive. Follow the on-screen instructions.

b The CD-ROM Top Menu will appear. Click

Install MFL-Pro Suite and click Yes if you accept the license agreements. Follow the on-screen instructions.

c Choose Local Connection, and then click

Next. The installation continues.

d When this screen appears, go to the next step.

Connect the USB cable

DCP-J515W

USB

LAN USB

DCP-J715W

Make sure that the cable does not restrict the cover from closing, or an error may occur.

USB

Now go to

IMPORTANT

Note

Finish

Note

The installation will continue automatically.

The installation screens appear one after another.

Windows

Finish and restart

a Click Finish to restart your computer.

After restarting the computer, you must be logged on with Administrator rights.

b In the Check for Firmware Updates screen,

choose the firmware update setting you want and click OK.

Internet access is required for the firmware update.

Windows

DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear.

f When the User’s Guides screen is displayed,

click View Manuals on the Web if you want to download the manuals and follow the on-screen instructions. You can also view the manuals on the documentation CD-ROM.

g When the On-Line Registration screen is

displayed, make your selection and follow the on-screen instructions.

h If you do not want to set your machine as the

Default printer, uncheck Set as Default Printer.

The installation is now complete.

Proceed to Install Optional Applications on page 22.

XML Paper Specification Printer Driver

The XML Paper Specification Printer Driver is the most suitable driver when printing from applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/

USB

Macintosh

USB

IMPORTANT

Macintosh

For USB interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

a Make sure your machine is connected to the

power and your Macintosh is ON. You must be logged on with Administrator rights.

Connect the USB cable

• DO NOT connect the machine to a USB port on a keyboard or a non-powered USB hub.

• Connect the machine directly to your Macintosh.

DCP-J515W

USB

Make sure that the cable does not restrict the cover from closing, or an error may occur.

LAN USB

DCP-J715W

USB

Finish

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive.

b Double-click the Start Here OSX icon to install. c Choose Local Connection, and then click

Next. Follow the on-screen instructions.

d Please wait, it will take a few seconds for the

software to install. After the installation, the Brother software will search for the Brother device.

e Choose the machine from the list, and then

click OK.

Macintosh

Windows

f When this screen appears, click Next.

g When the Brother Support screen appears,

click Close.

The installation is now complete.

USB

Macintosh

Wired Network

LAN USB

IMPORTANT

For wired network interface users (DCP-J715W only) (Windows Windows Vista

2000 Professional/XP/XP Professional x64 Edition/

/Windows® 7)

Before you install

a Make sure that your computer is ON and you

are logged on with Administrator rights.

Connect the network

cable

Windows

Make sure that the cable does not restrict the cover from closing, or an error may occur.

Wired Network

Now go to

Note

Finish

Note

Windows

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive. Follow the on-screen instructions.

b The CD-ROM Top Menu will appear. Click

Install MFL-Pro Suite and click Yes if you accept the license agreements. Follow the on-screen instructions.

c Choose Wired Network Connection, and

then click Next.

d When Firewall/AntiVirus detected screen

appears, choose Change the Firewall port

settings to enable network connection and continue with the installation. (Recommended) and click Next. (Not for

Windows

If you are using a firewall other than Windows Firewall see the instructions provided with your firewall software for information on how to add the following network ports.

 For network scanning, add UDP port 54925.  If you still have trouble with your network

• If there is more than one machine connected to the network, choose your machine from the list, and then click Next.

• If your machine is not found over the network, confirm your settings by following the on-screen instructions.

e The installation of the Brother drivers will

automatically start. The installation screens appear one after another.

2000 users)

connection, add UDP port 137.

Finish and restart

a Click Finish to restart your computer. After

restarting the computer, you must be logged on with Administrator rights.

b In the Check for Firmware Updates screen,

choose the firmware update setting you want and click OK.

Internet access is required for the firmware update.

The installation is now complete.

Proceed to Install Optional Applications on page 22.

• If you specify an IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see the Network User’s Guide on the documentation CD-ROM.

• XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver when printing from applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/

Windows

Wired Network

Macintosh

f When the User’s Guides screen is displayed,

click View Manuals on the Web if you want to download the manuals and follow the on-screen instructions. You can also view the manuals on the documentation CD-ROM.

g When the On-Line Registration screen is

displayed, make your selection and follow the on-screen instructions.

h If you do not want to set your machine as the

Default printer, uncheck Set as Default Printer.

Wired Network

LAN USB

For wired network interface users (DCP-J715W only) (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

a Make sure your machine is connected to the

power and your Macintosh is ON. You must be logged on with Administrator rights.

Macintosh

Connect the network cable

Wired Network

Finish

Note

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive.

b Double-click the Start Here OSX icon to install. c Choose Wired Network Connection, and

then click Next. Follow the on-screen instructions.

d Please wait, it will take a few seconds for the

software to install. After the installation, the Brother software will search for the Brother device.

e If the machine is configured for your network,

choose the machine from the list, and then click

OK.

Macintosh

f When this screen appears, click Next.

g When the Brother Support screen appears,

click Close.

The installation is now complete.

If you specify an IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see the Network User’s Guide on the documentation CD-ROM.

Windows

Wired Network

Macintosh

For Wireless Network Users

IMPORTANT

Note

For wireless network interface users

Before you begin

Although the Brother DCP-J715W can be used in both a wired and wireless network, only one of the connection methods can be used at a time.

If you have previously configured the wireless settings of the machine you must reset the network (LAN) settings before you can configure the wireless settings again. On your machine, press Menu. Press a or b to choose Network and press OK. Press a or b to choose Network Reset, and then press OK.

Press twice to choose Yes.

To set up your machine in Ad-hoc mode (connected to a wireless capable computer without an access point/router) you can find instructions in the Network User’s Guide on the documentation CD-ROM.

Also you can download the Network User’s Guide by following the instructions below. 1 Turn on your computer. Insert the installation CD-ROM into your CD-ROM drive. For Windows 2 Choose your model and the language. The CD-ROM top menu will appear. 3 Click Documentation, and follow the on-screen instructions. For Macintosh: 2 Double-click Documentation, and follow the on-screen instructions.

For Wireless Network Users

IMPORTANT

Note

Now go to

Confirm your network environment (Infrastructure Mode)

The following instructions will offer two methods for installing your Brother machine in a wireless network environment.

a If your wireless access point/router does not support Wi-Fi Protected Setup (WPS) or AOSS™, write

down the wireless network settings of your wireless access point/router in the area below.

Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings.

Item Record the current wireless network settings

Network Name: (SSID/ESSID)

Password (Network Key)

* The Password may also be described as the Network Key, Security Key or Encryption Key.

If you do not know this information (Network Name (SSID/ESSID) and Password (Network Key)), you cannot continue the wireless setup.

How can I find this information (Network Name (SSID/ESSID) and Password (Network Key))

1) You should see the documentation provided with your wireless access point/router.

2) The initial network name could be the manufacturer’s name or the model name.

3) If you do not know the security information, please consult the router manufacturer, your system administrator, or internet provider.

page 16

b If your wireless access point/router supports automatic wireless (one-push) setup (Wi-Fi Protected

Setup or AOSS™), you can find instructions in the Network User’s Guide on the documentation CD-ROM. To set up your machine in any other wireless environment (Ad-hoc mode) you can find instructions in the Network User’s Guide on the documentation CD-ROM.

Wireless Network

For Wireless Network Users

Now go to

Note

Connecting the Brother machine to the wireless network

Configure the wireless settings (typical Wireless

Setup in infrastructure mode)

a On your machine, press Menu.

Press a or b to choose Network and press OK. (For DCP-J715W, press a or b to choose WLAN and press OK.) Press a or b to choose Setup Wizard and press OK. When Enable WLAN? or Network I/F switched to Wireless. is displayed, press OK to accept. This will start the wireless setup wizard. To cancel, press Stop/Exit.

b The machine will search for available SSIDs. If

a list of SSIDs is displayed, use the a or b keys to choose the SSID you wrote down in step 11-a on page 15, then press OK. If you are using an authentication and encryption method that requires a Password (Network Key), go to c.

If your authentication method is Open System and your encryption mode is None, go to d.

e A connection result message appears for

60 seconds on the LCD and a wireless LAN report will automatically be printed. If the connection failed, check the error code on the printed report and refer to Troubleshooting on page 17.

Wireless setup is now complete. A four level indicator at the top of your machine’s LCD will show the wireless signal strength of your access point/router.

To install MFL-Pro Suite, continue to step 13.

For Windows® Users:

Page 19

For Macintosh Users:

Page 21

It will take several seconds to display a list of available SSIDs.

If a list of SSIDs is not displayed, make sure your access point is on. Move your machine closer to the access point and try starting from a again.

If your access point is set to not broadcast the SSID, you will have to manually add the SSID name. For details, see the Network User’s Guide on the documentation CD-ROM.

c Enter the Password (Network Key) you wrote

down in step 11-a on page 15. Press a, b, d or c to select a letter or number, and press OK.

When you have entered all the characters,

press a, b, d or c to select and press OK. Then press (Yes) to apply your settings.

d Your machine will now try to connect to your

wireless network using the information you have entered. It may take a few minutes to connect to your wireless network.

For Wireless Network Users

IMPORTANT

Troubleshooting

Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings.

How can I find the wireless security information (SSID and Network Key)

1) You should see the documentation provided with your wireless access point/router.

2) The initial network name could be the manufacturer’s name or the model name.

3) If you do not know the security information, please consult the router manufacturer, your system administrator, or internet provider.

* The Network Key may also be described as the Password, Security Key or Encryption Key.

Wireless LAN report

If the wireless LAN report that printed shows that the connection failed, check the error code on the printed report and refer to the following instructions.

Error code Recommended Solutions

The wireless setting is not activated, turn the wireless setting to ON.

- If a LAN cable is connected to your machine, disconnect it and turn the wireless setting of your machine to ON.

TS-01

TS-02

On your machine, press Menu. Press a or b to choose Network and press OK. Press a or b to choose WLAN Enable (For DCP-J515W) or Network I/F (For DCP-J715W) and press OK. Press a or b to choose On (For DCP-J515W) or WLAN (For DCP-J715W) and press OK. Press Stop/Exit.

The wireless access point/router cannot be detected.

1. Check the following 4 points.

- Make sure that the wireless access point/router is powered on.

- Move your machine to an obstruction-free area, or closer to the wireless access point/router.

- Temporarily place your machine within about one metre from the wireless access point when you are configuring the wireless settings.

- If your wireless access point/router is using MAC address filtering, confirm the MAC address of the Brother machine is allowed in the filter.

2. If you manually entered the SSID and security information (SSID/authentication method/encryption method/Network Key), the information may be incorrect. Reconfirm the SSID and security information and reenter the correct information as necessary.

See How can I find the wireless security information (SSID and Network Key) on page 17 to confirm.

Wireless Network

TS-04

For Wireless Network Users

The Authentication/Encryption methods used by the selected wireless access point/router are not supported by your machine.

For infrastructure mode, change the authentication and encryption methods of the wireless access point/router. Your machine supports the following authentication methods:

authentication method encryption method

WPA-Personal

WPA2-Personal AES

Open

Shared key WEP

If your problem is not solved, the SSID or network settings you entered may be incorrect. Reconfirm the wireless network settings.

See How can I find the wireless security information (SSID and Network Key) on page 17 to confirm.

None (without encryption)

TKIP

AES

WEP

TS-05

TS-06

TS-07

For ad-hoc mode, change the authentication and encryption methods of your computer for the wireless setting. Your machine supports Open authentication method only, with optional WEP encryption.

The security information (SSID/Network Key) is incorrect. Reconfirm the SSID and security information (Network Key). If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.

See How can I find the wireless security information (SSID and Network Key) on page 17 to confirm.

The wireless security information (Authentication method/Encryption method/Network Key) is incorrect. Reconfirm the wireless security information (Authentication method/Encryption method/Network Key) in the table of TS-04. If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.

See How can I find the wireless security information (SSID and Network Key) on page 17 to confirm.

The machine cannot detect a wireless access point/router that has WPS or AOSS™ enabled.

If you would like to configure your wireless settings using WPS or AOSS™, you must operate both your machine and the wireless access point/router. Confirm your wireless access point/router supports WPS or AOSS™ and try starting again.

TS-08

If you do not know how to operate your wireless access point/router using WPS or AOSS™ see the documentation provided with your wireless access point/router, ask the manufacturer of your wireless access point/router or ask your network administrator.

Two or more wireless access points that have WPS or AOSS™ enabled are detected.

- Confirm that only one wireless access point/router within range has the WPS or AOSS™ method active and try again.

- Try starting again after a few minutes in order to avoid interference from other access points.

Wireless Network

Note

Install the drivers & software (Windows Windows Vista

2000 Professional/XP/XP Professional x64 Edition/

/Windows® 7)

Before you install

Windows

e Choose your machine from the list, and then

click Next.

a Make sure that your computer is ON and you

are logged on with Administrator rights.

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive. Follow the on-screen instructions.

b The CD-ROM Top Menu will appear. Click

Install MFL-Pro Suite and click Yes if you accept the license agreements. Follow the on-screen instructions.

c Choose Wireless Network Connection, and

then click Next.

d When Firewall/AntiVirus detected screen

appears, choose Change the Firewall port

settings to enable network connection and continue with the installation. (Recommended) and click Next. (Not for

Windows

If you are using a firewall other than Windows Firewall see the instructions provided with your firewall software for information on how to add the following network ports.

 For network scanning, add UDP port 54925.  If you still have trouble with your network

2000 users)

connection, add UDP port 137.

• If your wireless settings fail, the Wireless Device Setup Wizard will appear during the installation of MFL-Pro Suite. Confirm your settings by following the on-screen instructions. If you encounter this failure, go to step 11-a on page 15 and setup the wireless connection again.

• If you are using WEP and the LCD displayed Connected but your machine is not found, make sure you entered the WEP key correctly. The WEP key is case sensitive.

f The installation of the Brother drivers will

automatically start. The installation screens appear one after another.

g When the User’s Guides screen is displayed,

click View Manuals on the Web if you want to download the manuals and follow the on-screen instructions. You can also view the manuals on the documentation CD-ROM.

h When the On-Line Registration screen is

displayed, make your selection and follow the on-screen instructions.

i If you do not want to set your machine as the

Default printer, uncheck Set as Default Printer.

Windows

Wireless Network

Macintosh

Wireless Network

Now go to

Note

Finish

Note

Finish and restart

a Click Finish to restart your computer. After

restarting the computer, you must be logged on with Administrator rights.

b In the Check for Firmware Updates screen,

choose the firmware update setting you want and click OK.

Internet access is required for the firmware update.

The installation is now complete.

Windows

Proceed to Install Optional Applications on page 22.

• If you specify an IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see the Network User’s Guide on the documentation CD-ROM.

Wireless Network

Note

Finish

Note

Install the drivers & software (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

a Make sure your machine is connected to the

power and your Macintosh is ON. You must be logged on with Administrator rights.

Macintosh

g When the Brother Support screen appears,

click Close.

The installation is now complete.

Install MFL-Pro Suite

a Put the supplied installation CD-ROM into your

CD-ROM drive.

b Double-click the Start Here OSX icon to install. c Choose Wireless Network Connection, and

then click Next.

d The Brother software will search for the Brother

device in your wireless network. If the machine is configured for your network, choose the device you want to install, and then click Next.

If your wireless settings fail, the Wireless Device Setup Wizard will appear during the installation of MFL-Pro Suite. Confirm your settings by following the on-screen instructions. If you encounter this failure, go to step 11-a on page 15 and setup the wireless connection again.

If you specify an IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see the Network User’s Guide on the documentation CD-ROM.

e Please wait, it will take a few seconds for the

software to install. After the installation, this window will appear.

Choose your machine from the list, and then click OK.

f When this screen appears, click Next.

Windows

Wireless Network

Macintosh

Install Optional Applications

IMPORTANT

Note

Install FaceFilter Studio/BookScan &

Whiteboard Suite supported by Reallusion, Inc

• The machine must be ON and connected to

the computer.

• The computer must be connected to the

Internet.

• Make sure you are logged on with

Administrator rights.

• This application is not available for

Windows Server

2003/2008 series.

a Open the top menu again by ejecting and then

reinserting the installation CD-ROM or by double-clicking the start.exe program from the root folder.

a To run FaceFilter Studio, go to

Start/All Programs/Reallusion/ FaceFilter Studio on your computer.

b Click the button on the upper right

corner of the screen.

c Click Check for updates to go to the

Reallusion update web page.

d Click the Download button and choose a folder

to save the file in.

e Close FaceFilter Studio before you start the

installer for FaceFilter Studio Help. Double-click the downloaded file from the folder you specified and follow the on-screen instructions for installation.

Windows

Install FaceFilter Studio Help

b The CD-ROM Top Menu will appear. Choose

your language and then click Additional Applications.

c Click the button for the application you want to

install.

d Go back to the Additional Applications screen

to install more applications.

To view the complete FaceFilter Studio Help, choose Start/All Programs/Reallusion/ FaceFilter Studio/FaceFilter Studio Help on your computer.

For Network Users

Restore the network settings to factory default

To restore all network settings of the internal Print/Scan server to factory default, please follow the steps below.

a Make sure the machine is not operating, then disconnect all the cables from the machine (except the power

cord).

b Press Menu. c Press a or b to choose Network.

Press OK.

d Press a or b to choose Network Reset.

Press OK.

e Press to choose Yes. f Press to choose Yes. g The machine will restart, re-connect cables once this is complete.

Entering Text for Wireless Settings

Press a, b, d or c to select a letter, and press OK. Select and press OK to cycle between upper case, lower case or special characters.

Inserting spaces To enter a space, choose special characters. Then press a, b, d or c to select , and press OK.

Making corrections

If you entered an incorrect letter and want to change it, press a, b, d or c to select or . Press OK several times to move the cursor under the incorrect character. Then press a, b, d or c to select , and press OK.

Re-enter the correct letter.

Trademarks

The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries, Ltd. Multi-Function Link is a registered trademark of Brother International Corporation. Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries. Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or other countries. Apple, Macintosh and Safari are trademarks of Apple Inc., registered in the United States and other countries. FaceFilter Studio is a trademark of Reallusion, Inc. AOSS is a trademark of Buffalo Inc. Wi-Fi, WPA, WPA2, Wi-Fi Protected Access and Wi-Fi Protected Setup are either trademarks or registered trademarks of Wi-Fi Alliance in the United States and/or other countries. Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.

Any trade names and product names of companies appearing on Brother products, related documents and any other materials are all trademarks or registered trademarks of those respective companies.

Compilation and Publication

Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.

©2010 Brother Industries, Ltd. All rights reserved. This product includes software developed by the following vendors: ©1983-1998 PACIFIC SOFTWORKS, INC. This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC,Inc. ©2008 Devicescape Software, Inc.

Get inspired. Double-click the Brother CreativeCenter icon on your desktop to access a FREE web site with many ideas and resources for personal and professional use.

http://www.brother.com/creativecenter/

Brother DCP-J515W, DCP-J715W Setup Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Start Here

Unpack the machine and check the components

Load plain A4 paper

Connect the power cord

Install the ink cartridges

Choose your language

Check the print quality

Set the date and time

Choose your connection type

Before you install

Install MFL-Pro Suite

Connect the USB cable

Finish and restart

For USB interface users (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

Connect the USB cable

Install MFL-Pro Suite

Before you install

Install MFL-Pro Suite

Finish and restart

For wired network interface users (DCP-J715W only) (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

Connect the network cable

Install MFL-Pro Suite

For wireless network interface users

Before you begin

Confirm your network environment (Infrastructure Mode)

Connecting the Brother machine to the wireless network

Troubleshooting

How can I find the wireless security information (SSID and Network Key)

Wireless LAN report

Before you install

Install MFL-Pro Suite

Finish and restart

Install the drivers & software (Mac OS X 10.4.11, 10.5.x, 10.6.x)

Before you install

Install MFL-Pro Suite

Install FaceFilter Studio Help

For Network Users

Restore the network settings to factory default

Entering Text for Wireless Settings