Brooks Instrument 1306 Operating Manual
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016 Models GT1306 and GT1307
5
Models GT1306 and GT1307
O-ring Seal Flowmeters
Models GT1306/07
NPT Connection,
Standard
Models GT1306/07
Flanged Connection,
FV Retrofit
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
Models GT1306 and GT1307
October, 2016
Essential Instructions
Read before proceeding!
Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly
installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to
and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.
• To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.
• Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover
for local sales office contact information. Save this instruction manual for future reference.
WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed
this warning can result in serious personal injury and / or damage to the equipment.
• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.
• Follow all warnings, cautions and instructions marked on and supplied with the product.
WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can
result in serious personal injury and / or damage to the equipment.
• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.
Connect all products to the proper electrical and pressure sources.
• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet
and outlet connections. If no leaks are present, bring the system up to the operating pressure.
• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use
replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe
operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.
• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when
maintenance is being performed by qualified persons.
WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely
drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.
European Pressure Equipment Directive (PED)
All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).
• The Specifications Section of this manual contains instructions related to the PED directive.
• Products described in this manual are in compliance with EN directive 2014/34/EU.
• All Brooks Instrument Flowmeters fall under fluid group 1.
• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.
• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).
European Electromagnetic Compatibility (EMC)
The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic
Compatibility (EMC directive 2014/30/EU).
Special attention however is required when selecting the signal cable to be used with CE marked equipment.
Quality of the signal cable, cable glands and connectors:
Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.
If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.
“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.
The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.
The shield should be terminated to an earth ground.
Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.
The shield should be terminated to an earth ground.
For pin configuration : Please refer to the enclosed Instruction Manual.
ESD (Electrostatic Discharge)
CAUTION: This instrument contains electronic components that are susceptible to damage by st atic electricity. Proper handling procedures must be observed
during the removal, installation or other handling of internal circuit boards or devices.
Handling Procedure:
1. Power to unit must be removed.
2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,
removed or adjusted.
3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before
installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.
Comments
This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components
that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these
devices. Damaged components, even though they appear to function properly, exhibit early failure.
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016 Models GT1306 and GT1307
Dear Customer,
We appreciate this opportunity to service your flow measurement and control requirements with a Brooks
Instrument device. Every day , flow customers all over the world turn to Brooks Instrument for solutions to their
gas and liquid low-flow applications. Brooks provides an array of flow measurement and control products for
various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices,
analytical instrumentation, semiconductor manufacturing, and more.
The Brooks product you have just received is of the highest quality available, offering superior performance,
reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements
and hostile process environments in mind to provide you with a lifetime of dependable service.
We recommend that you read this manual in its entirety. Should you require any additional information concerning
Brooks products and services, please contact your local Brooks Sales and Service Office listed on the back cover
of this manual or visit www.BrooksInstrument.com
Y ours sincerely ,
Brooks Instrument
WARNING
GLASS TUBE
EXPLOSION
HAZARD
Plastic protective sleeve must remain over glass
tube.
Fasten meter windowssecurely .
Do not operate above pressure and temperature
limits.
Avoid pressure and flow surges.
Do not service or repair while pressurized.
Read and understand instruction manual.
Failure to comply could result in serious personal
injury or property damage.
WARNING
GLASS TUBE EXPLOSION HAZARD
Protective sleeve
Fasten meter wind ows securely.
Failure to comp ly could resu lt in serious personal
injury or property da mage.
must
remain
over
glass
tube.
Models GT1306 and GT1307
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016 Models GT1306 and GT1307
Paragraph Page
Number Number
Section 1 Introduction
1-1 Description .........................................................................................................................................1-1
1-2 Design Features.................................................................................................................................1-1
1-3 Specifications .....................................................................................................................................1-1
1-4 Optional Equipment............................................................................................................................1-2
Section 2 Installation
2-1 Receipt of Equipment.........................................................................................................................2-1
2-2 Recommended Storage Practice .......................................................................................................2-1
2-3 Return Shipment ................................................................................................................................2-2
2-4 T ransit Precautions ............................................................................................................................2-2
2-5 Removal from Storage .......................................................................................................................2-2
2-6 Installation .......................................................................................................................................... 2-2
Section 3 Operation
3-1 Operating Instructions ........................................................................................................................3-1
Section 4 Maintenance and Cleaning
4-1 General ..............................................................................................................................................4-1
Section A Essential Instructions.............................................................................................................A-1
Warranty, Local Sales/Service Contact Information....................................................................... Back Cover
Figures
Figure Page
Number Number
1-1 Dimensions, Model GT1306...............................................................................................................1-5
1-1 Dimensions, Model GT1307...............................................................................................................1-8
1-3 Float T ypes.........................................................................................................................................1-7
2-1 T ypical Byp ass Installation .................................................................................................................2-3
3-1 Reading Edge of Floats......................................................................................................................3-2
3-2 T ypical Byp ass Installation .................................................................................................................3-2
Tables
Table Page
Number Number
1-1 Specifications, Model GT1306 ...........................................................................................................1-3
1-2 Capacities, Model GT1306................................................................................................................. 1-4
1-3 Pressure/Temperature Ratings, Model GT1306................................................................................. 1-4
1-4 Specifications, Model GT1307 ...........................................................................................................1-6
1-5 Capacities, Model GT1307................................................................................................................. 1-7
1-6 Pressure/Temperature Ratings, Model GT1307................................................................................. 1-7
Models GT1306 and GT1307
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016
1-1 Description
1-2 Design Features
1-3 Specifications
Section 1 Introduction
Models GT1306 and GT1307
Models GT1306 and GT1307 O-ring seal flowmeters are rugged,
economical, accurate indicating flowmeters f or liquids and gasses and can
be a “drop-in” replacement f or man y Full-View® models.
• Rugged side-plate construction - protects glass tube from piping stress
and/or vibration
• O-ring seal - inlet and outlet same size - positive seal - easy to maintain
• Choice of float types and capacity ranges - broad range of flow rates
• V ertical or horizontal NPT/flanged connections - meter can be easily
adapted to customer piping
• Model 1100 Series (Full-View) replacement
Specifications
Model GT1306: See Table 1-1
Model GT1307: See Table 1-4
Capacities
Model GT1306: See Table 1-2
Model GT1307: See Table 1-5
Pressure/T emperature Ratings
Model GT1306: See Table 1-3
Model GT1307: See Table 1-6
1-1
Section 1 Introduction
Models GT1306 and GT1307
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016
Dimensions
Model GT1306: See Figure 1-1
Model GT1307: See Figure 1-2
Float T ypes
See Figure 1-3
WARNING
GLASS TUBE
EXPLOSION
HAZARD
Plastic protective sleeve must remain over glass
tube.
Fasten meter windows securely .
Do not operate above pressure and temperature
limits.
Avoid pressure and flow surges.
Do not service or repair while pressurized.
Read and understand instruction manual.
Failure to comply could result in serious personal
injury or property damage.
1-4 Optional Equipment
WARNING
GLASS TUBE EXPLOSION HAZARD
Protectivesleeve
Fasten mete r windows secure ly .
Failure to comp ly could resu lt in serious pe rsonal
injury or property da mage.
Mounting - flush or front of panel
must
remain
over
glass
tube.
1-2
Installation and Operation Manual
Section 1 Introduction
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016
Table 1-1 Specifications, Model GT1306
Capacities and Pressure DropsCapacities and Pressure Drops
Capacities and Pressure Drops See Capacities Table 1-2
Capacities and Pressure DropsCapacities and Pressure Drops
PrPr
essuressur
e Ratingse Ratings
Pr
essur
e Ratings See Pressure/Temperature Table 1-3
PrPr
essuressur
e Ratingse Ratings
Flow AccuracyFlow Accuracy
Flow Accuracy Standard: ±2% Full Scale, Class 2.5 acc VDI/VDE
Flow AccuracyFlow Accuracy
RepeatabilityRepeatability
Repeatability 0.5% Full Scale
RepeatabilityRepeatability
Scale LengthScale Length
Scale Length 150mm
Scale LengthScale Length
Scale GraduationsScale Graduations
Scale Graduations Direct reading, engraved detachable metal plate
Scale GraduationsScale Graduations
Ambient Temperature LimitsAmbient Temperature Limits
Ambient Temperature Limits 33 to 125°F (1°C to 52°C)
Ambient Temperature LimitsAmbient Temperature Limits
Operating Fluid Temperature LimitsOperating Fluid Temperature Limits
Operating Fluid Temperature Limits See Pressure/Temperature Table 1-3
Operating Fluid Temperature LimitsOperating Fluid Temperature Limits
ConnectionsConnections
Connections Female NPT, Rc/150# flange - vertical or horizontal
ConnectionsConnections
DimensionsDimensions
Dimensions See Dimensions Figure 1-1
DimensionsDimensions
Materials of ConstructionMaterials of Construction
Materials of Construction
Materials of ConstructionMaterials of Construction
Metering TubeMetering Tube
Metering Tube Borosilicate glass
Metering TubeMetering Tube
Protective Tube SleeveProtective Tube Sleeve
Protective Tube Sleeve UV stabilized polycarbonate
Protective Tube SleeveProtective Tube Sleeve
WindowWindow
Window Scratch resistant, UV stabilized polycarbonate (stainless steel frames standard with stainless steel side plates)
WindowWindow
Floats & Float StopsFloats & Float Stops
Floats & Float Stops Glass, sapphire, 316 stainless steel or carboloy / Teflon float stops all sizes
Floats & Float StopsFloats & Float Stops
HousingHousing
Housing Aluminum, stainless steel side plates (stainless steel standard Full-View replacement)
HousingHousing
End FittingsEnd Fittings
End Fittings Brass or 316 stainless steel
End FittingsEnd Fittings
O-rings/PackingO-rings/Packing
O-rings/Packing Buna-N, Viton®-A fluoroelastomers, Kalrez® 4079 perfluoroelastomers (Sizes 7-10);
O-rings/PackingO-rings/Packing
Optional EquipmentOptional Equipment
Optional Equipment Mountings: Brackets for flush or front of panel
Optional EquipmentOptional Equipment
Optional: ±1% Full Scale, Class 1.6 acc VDI/VDE
Neoprene, Viton® or Teflon® packing (Sizes 2-6)
Valves: Available for connection sizes 1/2” through 1” only. Piped in outlet or inlet
Models GT1306 and GT1307
1-3
Section 1 Introduction
Models GT1306 and GT1307
Table 1-2 Capacities, Model GT1306
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016
Table 1-3 Pressure/Temperature Ratings, Model GT1306
Pr Pr
essuressur
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 500 34.5 SEP 250 121
#6 450 31 SEP 250 121
#7 350 24 SEP 250 121
#8 300 20.7 SEP 250 121
#9/10 100 6.9 SEP 250 121
(Values apply to unit with valve - sizes 7-10)
Pr Pr
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 276 19 SEP 226 15.6
#6 276 19 SEP 226 15.6
#7 276 19 SEP 226 15.6
#8 276 19 SEP 226 15.6
1-4
#9/10 100 6.9 SEP 100 6.9
e Rating for Female e Rating for Female
essur
e Rating for Female
essuressur
e Rating for Female e Rating for Female
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
PrPr
Pr
PrPr
PSIG Bar °F °C
essuressur
e Rating for Flanged (150#) 1306 Unitse Rating for Flanged (150#) 1306 Units
essur
e Rating for Flanged (150#) 1306 Units
essuressur
e Rating for Flanged (150#) 1306 Unitse Rating for Flanged (150#) 1306 Units
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
PrPr
essuressur
e @ 70°Fe @ 70°F
Pr
essur
e @ 70°F
PrPr
essuressur
e @ 70°Fe @ 70°F
PSIG Bar PSIG Bar
essuressur
essur
essuressur
ee
e
ee
atingating
ating
atingating
atingating
ating
atingating
/21°C/21°C
/21°C
/21°C/21°C
ThrThr
eaded 1306 Unitseaded 1306 Units
Thr
eaded 1306 Units
ThrThr
eaded 1306 Unitseaded 1306 Units
PEDPED
PED
PEDPED
PEDPED
Pr Pr
PED
Pr
PEDPED
Pr Pr
essuressur
essur
essuressur
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
TT
emperemper
T
emper
TT
emperemper
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
e @ 250°Fe @ 250°F
e @ 250°F
e @ 250°Fe @ 250°F
aturatur
atur
aturatur
atingating
ating
atingating
ee
e
ee
atingating
ating
atingating
/121°C/121°C
/121°C
/121°C/121°C
Pr Pr
essuressur
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 217 15 SEP 250 121
#6 145 10 SEP 250 121
#7 152 10.5 SEP 250 121
#8 116 8 SEP 250 121
#9/10 80 5.5 SEP 250 121
e Rating for Female e Rating for Female
essur
e Rating for Female
essuressur
e Rating for Female e Rating for Female
1306 Units 1306 Units
1306 Units
1306 Units 1306 Units
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
PrPr
essuressur
ee
Pr
essur
e
PrPr
essuressur
PSIG Bar °F °C
ee
With CRN With CRN
With CRN
With CRN With CRN
atingating
ating
atingating
ThrThr
eaded & Flanged (150#)eaded & Flanged (150#)
Thr
eaded & Flanged (150#)
ThrThr
eaded & Flanged (150#)eaded & Flanged (150#)
ApprAppr
ovaloval
Appr
oval
ApprAppr
PEDPED
PED
PEDPED
ovaloval
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
TT
emperemper
T
emper
TT
emperemper
aturatur
atur
aturatur
atingating
ating
atingating
ee
e
ee
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016
Section 1 Introduction
Models GT1306 and GT1307
Figure 1-1 Dimensions, Model GT1306
1-5
Section 1 Introduction
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
Models GT1306 and GT1307
Table 1-4 Specifications, Model GT1307
Capacities and Pressure DropsCapacities and Pressure Drops
Capacities and Pressure Drops See Capacities Table 1-5
Capacities and Pressure DropsCapacities and Pressure Drops
PrPr
essuressur
e Ratingse Ratings
Pr
essur
e Ratings See Pressure/Temperature Table 1-6
PrPr
essuressur
e Ratingse Ratings
Flow AccuracyFlow Accuracy
Flow Accuracy Standard: ±2% Full Scale, Class 2.5 acc VDI/VDE
Flow AccuracyFlow Accuracy
RepeatabilityRepeatability
Repeatability 0.5% Full Scale
RepeatabilityRepeatability
Scale LengthScale Length
Scale Length 250mm
Scale LengthScale Length
Scale GraduationsScale Graduations
Scale Graduations Direct reading, engraved detachable metal plate
Scale GraduationsScale Graduations
Ambient Temperature LimitsAmbient Temperature Limits
Ambient Temperature Limits 33 to 125°F (1°C to 52°C)
Ambient Temperature LimitsAmbient Temperature Limits
Operating Fluid Temperature LimitsOperating Fluid Temperature Limits
Operating Fluid Temperature Limits See Pressure/Temperature Table 1-6
Operating Fluid Temperature LimitsOperating Fluid Temperature Limits
ConnectionsConnections
Connections Female NPT/150# flange - vertical or horizontal
ConnectionsConnections
DimensionsDimensions
Dimensions See Dimension Figures 1-2
DimensionsDimensions
Materials of ConstructionMaterials of Construction
Materials of Construction
Materials of ConstructionMaterials of Construction
Metering TubeMetering Tube
Metering Tube Borosilicate glass
Metering TubeMetering Tube
Protective Tube SleeveProtective Tube Sleeve
Protective Tube Sleeve UV stabilized polycarbonate
Protective Tube SleeveProtective Tube Sleeve
WindowWindow
Window Scratch resistant, UV stabilized polycarbonate (stainless steel frames standard with stainless steel side plates)
WindowWindow
Floats & Float StopsFloats & Float Stops
Floats & Float Stops Glass, sapphire, 316 stainless steel or carboloy / Teflon float stops all sizes
Floats & Float StopsFloats & Float Stops
HousingHousing
Housing Aluminum, stainless steel side plates (stainless steel standard Full-View replacement)
HousingHousing
End FittingsEnd Fittings
End Fittings Brass or 316 stainless steel
End FittingsEnd Fittings
O-rings/PackingO-rings/Packing
O-rings/Packing Buna-N, Viton®-A fluoroelastomers, Kalrez® 4079 perfluoroelastomers (Sizes 8-10)
O-rings/PackingO-rings/Packing
Optional EquipmentOptional Equipment
Optional Equipment Mountings: Brackets for front of panel
Optional EquipmentOptional Equipment
Optional: ±1% Full Scale, Class 1.6 acc VDI/VDE
Neoprene, Viton® or Teflon® packing (Sizes 2, 6)
October , 2016
1-6
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October, 2016
Table 1-5 Capacities, Model GT1307
Section 1 Introduction
Models GT1306 and GT1307
Table 1-6 Pressure/Temperature Ratings, Model GT1307
Pr Pr
essuressur
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 500 34.5 SEP 250 121
#6 450 31 SEP 250 121
#8 300 20.7 SEP 250 121
#9 175 12.1 SEP 250 121
#10 100 6.9 SEP 250 121
Pr Pr
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 276 19 SEP 226 15.6
#6 276 19 SEP 226 15.6
#8 276 19 SEP 226 15.6
#9 175 12.1 SEP 175 12.1
#10 100 6.9 SEP 100 6.9
e Rating for Female e Rating for Female
essur
e Rating for Female
essuressur
e Rating for Female e Rating for Female
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
PrPr
essuressur
ee
Pr
essur
e
PrPr
essuressur
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
e @ 70°Fe @ 70°F
e @ 70°F
e @ 70°Fe @ 70°F
ee
PSIG Bar °F °C
essuressur
e Rating for Flanged (150#) 1307 Unitse Rating for Flanged (150#) 1307 Units
essur
e Rating for Flanged (150#) 1307 Units
essuressur
e Rating for Flanged (150#) 1307 Unitse Rating for Flanged (150#) 1307 Units
PrPr
essuressur
Pr
essur
PrPr
essuressur
PSIG Bar PSIG Bar
atingating
ating
atingating
atingating
ating
atingating
/21°C/21°C
/21°C
/21°C/21°C
ThrThr
eaded 1307 Unitseaded 1307 Units
Thr
eaded 1307 Units
ThrThr
eaded 1307 Unitseaded 1307 Units
PEDPED
PED
PEDPED
PEDPED
Pr Pr
PED
Pr
PEDPED
Pr Pr
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
TT
emperemper
T
emper
TT
emperemper
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
essuressur
e @ 250°Fe @ 250°F
essur
e @ 250°F
essuressur
e @ 250°Fe @ 250°F
aturatur
atur
aturatur
atingating
ating
atingating
ee
e
ee
atingating
ating
atingating
/121°C/121°C
/121°C
/121°C/121°C
Pr Pr
essuressur
Pr
Pr Pr
MeterMeter
Meter
MeterMeter
SizeSize
Size
SizeSize
#2 217 15 SEP 250 121
#6 217 15 SEP 250 121
#8 94 6.5 SEP 250 121
#9 72 5 SEP 250 121
#10 72 5 SEP 250 121
e Rating for Female e Rating for Female
essur
e Rating for Female
essuressur
e Rating for Female e Rating for Female
1307 Units 1307 Units
1307 Units
1307 Units 1307 Units
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
PrPr
essuressur
ee
Pr
essur
e
PrPr
essuressur
PSIG Bar °F °C
ee
With CRN With CRN
With CRN
With CRN With CRN
atingating
ating
atingating
ThrThr
eaded & Flanged (150#)eaded & Flanged (150#)
Thr
eaded & Flanged (150#)
ThrThr
eaded & Flanged (150#)eaded & Flanged (150#)
ApprAppr
ovaloval
Appr
oval
ApprAppr
PEDPED
PED
PEDPED
ovaloval
Max. OperMax. Oper
Max. Oper
Max. OperMax. Oper
TT
emperemper
T
emper
TT
emperemper
aturatur
atur
aturatur
atingating
ating
atingating
ee
e
ee
1-7
Section 1 Introduction
Models GT1306 and GT1307
Installation and Operation Manual
X-VA-1306-1307-eng
Part Number: 541B079AAG
October , 2016
Figure 1-2 Dimensions, Model GT1307
1-8
Loading...