Broan SPK110 SPEAKER FAN Instructions Manual
MODEL SPK110
SPEAKER FAN
READ AND SAVE THESE INSTRUCTIONS
MODEL SPK110
Page 1
To register this product visit:
www.broan.com
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent backdrafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Acceptable for use over a tub or shower when connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch circuit
(ceiling installation only).
8. This unit must be grounded.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
2. This product is designed for installation in ceilings up to a 12/12
pitch (45 degree angle). Duct connector must point up. DO NOT
MOUNT THIS PRODUCT IN A WALL.
3. To avoid motor bearing damage, noisy and/or unbalanced impellers,
or speaker damage, keep drywall spray, construction dust, etc. off
power unit and speaker diaphrams.
4. Please read specification label on product for further information
and requirements.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit with the
dusting brush attachment. Be careful vacuuming around speakers.
The motor is permanently lubricated and never needs oiling. If the
motor bearings are making excessive or unusual noises, replace
the blower assembly (includes motor and impeller).
OPERATION
Use an on/off switch to operate this ventilator. Do not use a solidstate speed control with this Speaker Fan. See “Connect Wiring”
for details.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth® SIG, Inc. and any use of such marks by Broan-NuTone LLC is under
license. Other trademark and trade names are those of their respective owners.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules and RSS-210 of Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC ID: 2ADLL-99528551 IC: 2143B-99528551
This Bluetooth® wireless technology enabled Speaker complies with FCC radiation
exposure limits set forth for an uncontrolled environment. End users must follow
the specific operating instructions for satisfying exposure compliance. This
speaker must not be co-located or operate in conjunction with any other antenna
or transmitter.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
INSTALL SPEAKER INTO HOUSING
MODEL SPK110
Page 2
Video instruction for speaker installation are also available
at: www.broan.com
FAN MOTOR
PLUG
1. Disconnect FAN MOTOR PLUG.
#8-32 X 5/8”
SCREWS
SPEAKER
BRACKET
#8-32 X 5/8”
SCREWS
SPEAKER
BRACKET
BRACKET
OPENING
FAN PARTITION
PLATE
SPEAKER PLUG
2. Partially install (2) #8-32 x 5/8 screws (Included in parts
bag - discard short screws and metal bracket) into threaded
holes in SPEAKER BRACKET - only so ends of screws are
flush with bottom surface of speaker bracket. Note: Installing
screws below flush will make the next couple of steps difficult.
SPEAKER WIRE
RECEPTACLE
FAN MOTOR PLUG
3. Insert speaker into fan housing. Make sure SPEAKER
BRACKET hooks over edge of BRACKET OPENING.
4. Make sure rear surface of speaker is located as close to
wall of fan housing as possible.
5. Turn #8-32 X 5/8” SCREWS (partially installed in Step
2) until they make contact with FAN PARTITION PLATE.
Alternately tighten both screws. DO NOT OVERTIGHTEN.
NOTE: Screws are designed to raise and tighten speaker
bracket against motor bracket. Screw heads may or may
not contact speaker bracket when tight.
6. Insert SPEAKER PLUG into power receptacle where
motor plug was disconnected.
7. Connect FAN MOTOR PLUG into SPEAKER WIRE
RECEPTACLE.
Cooking
Equipment
Floor
COOKING AREA
Do not install above or
inside this area.
45
o
45
o
NOT FOR USE IN
A COOKING AREA.
ELBOWS*
TYPICAL INSTALLATIONS
MODEL SPK110
Page 3
Housing mounted to joists.
Housing mounted to truss.
To mount housing
anywhere between
joists, i-joists or trusses,
use optional hanger
bar kit QTHB1 (sold
separately). Follow
mounting instructions
included with kit.
PLAN THE INSTALLATION
Housing mounted to I-joists.
Use I-joist spacer block (provided).
The ducting
from this fan
to the outside
of the building
has a strong
effect on the
air flow, noise
and energy use
of the fan. Use
the shortest,
straightest duct
routing possible for best
performance,
and avoid installing the fan with smaller ducts than recommended. Insulation around
the ducts can reduce energy loss and inhibit mold growth. Fans installed
with existing ducts may not achieve their rated airflow.
POWER
CABLE*
Seal gaps
around
housing.
4-IN. ROUND
*Purchase
separately.
INSULATION
(Place around and
over fan housing.)
FAN
HOUSING
DUCT*
Seal duct
joints with
tape.
OR
4-IN. ROUND
ROOF CAP*
(with built-in
damper)
Keep duct
runs short.
WALL CAP*
(with built-in
damper)
INSTALL HOUSING & DUCT
1. Use a pliers to
bend housing
TABS out to 900.
TABS
2. Hold housing in place
so that the housing
tabs contact the
(use for mounting to I-Joist)
SPACER
bottom of the joist.
The housing mounts
with four (4) screws
or nails. Screw or
nail housing to joist
through lowest holes
in each mounting
flange, then through
highest holes. NOTE:
I-JOIST
Mounting to I-JOIST
(shown) requires use of SPACERS (included) between the
highest hole of each mounting flange and the I-joist.
MODEL SPK110
SPEAKER
Page 4
3. Snap damper /
duct connector onto housing.
Make sure connector is flush with
top of housing and
damper flap falls
closed.
CONNECT WIRING
1. Run 120 VAC house wiring to installation location. Use proper
UL approved connector to secure house wiring to wiring plate.
Connect wires as shown in wiring diagrams.
4. Connect 4-inch round
ductwork to damper /
duct connector. Run
ductwork to a roof cap
or wall cap. Tape all
ductwork connections to
make them secure and
air tight.
FINISH CEILING & INSTALL GRILLE
BEFORE FINISHING CEILING:
To avoid motor bearing damage, noisy and/or unbalanced
impellers, or speaker damage - you may want to cover
the housing opening - to keep drywall spray, construction dust, etc.
off power unit and speaker diaphrams.
1. Install ceiling
material. Cut out
around housing.
2. Squeeze grille
springs and insert
them into slots
on each side of
housing.
3. Push grille against
4. Turn on power to fan.
5. Go to Bluetooth® Speaker Operation section for Bluetooth®
SERVICE NOTES
To remove Blower Assembly:
Remove speaker assembly. Unplug motor. Remove thumbscrew
(10) from motor plate flange Find the single TAB on the motor
plate (located next to the receptacle). Push up near motor plate
tab while pushing out on side of housing. Or insert a straightblade screwdriver into slot in housing (next to tab) and twist
screwdriver.
To remove Speaker Assembly:
Unplug motor from speaker wiring. Unplug speaker wiring from
wire panel. Remove (2) screws from speaker bracket. Unhook
speaker bracket from motor bracket and remove speaker.
ceiling.
speaker operating instructions.
Bluetooth
®
wireless technology
SPEAKER OPERATION
MODEL SPK110
Page 5
To connect to the Broan-NuTone Bluetooth® wireless technology
Speaker for the rst time:
1. To play your personal music or audio files, you need a Bluetooth
wireless technology enabled Smart Phone, Tablet, or any other
such device.
2. Set your device to a low-to-midrange volume before connecting to
the speaker.
3. Make sure Fan is ON and Bluetooth® wireless technology enabled
device is located within 10 meters (approximately 33 feet) of the
Speaker/Fan.
4. Pairing your Bluetooth® wireless technology enabled device with
the Speaker:
a. For iPad/iPhone/iPod touch:
i. From your iPad/iPhone/iPod touch home page, tap
Settings.
ii. From Settings, tap General (if you have iOS 7 or
greater, you can skip this step).
iii. From General, tap Bluetooth.
iv. Move the Bluetooth® Slider to ON/green (if it isn’t
ON already). When you do this, a list of discoverable
Bluetooth® wireless technology devices will appear.
v. The Broan-NuTone Speaker has the Bluetooth® identifier
“Sensonic™ Vent Fan”. This identifier should be
in the list of Discoverable Devices. If not, turn the
Fan OFF, then ON, then turn Bluetooth® OFF, then ON.
• If “Sensonic™ Vent Fan” is still not on the list,
consult with the owner’s manual for your device
and follow the procedure for Pairing/Connecting a
Bluetooth® wireless technology device.
vi. Tap on “Sensonic™ Vent Fan” to complete the pairing
of the Bluetooth® wireless technology Speaker with
your Apple device.
b. For Android Phone/Tablet:
i. From your smart phone/tablet home page, tap Settings.
ii. From the Settings menu, go to Wireless & Controls,
Wireless & Networks, or something similar.
iii. Find Bluetooth®, Bluetooth® Settings or something
similar and tap Bluetooth® or move Bluetooth® Slider
to ON (if it isn’t on already).
iv. On the Bluetooth® screen, tap “Scan for Devices”,
“Search for Devices” or something similar.
v. The Broan-NuTone Speaker has the Bluetooth®
identifier “Sensonic™ Vent Fan”. This identifier
should show up in the list of Available Devices. If not,
turn Fan OFF, then ON, and repeat pairing procedure.
• If “Sensonic™ Vent Fan” is still not on the list,
consult with the owner’s manual for your
Android device and follow the procedure
for Pairing/Connecting a Bluetooth® device.
vi. Tap on “Sensonic™ Vent Fan” to complete the pairing
of the Bluetooth® wireless technology Speaker with
your Android device.
c. For all other Bluetooth® wireless technology enabled devices:
i. Follow the instructions that came with your Bluetooth®
wireless technology enabled Phone, Tablet or Pad
device to set it to search for Bluetooth® wireless
technology accessories.
ii. Most Bluetooth® wireless technology enabled devices
will require you to go to the “Paired Devices” (or
similar) screen and SELECT “Search for Devices” or
something similar.
iii. The Broan-NuTone Speaker has the Bluetooth® identifier
“Sensonic™ Vent Fan”. This identifier should show
up in the list of Available Devices, Discoverable
Devices or similar. If not, turn Fan OFF, then ON, and
repeat pairing procedure.
1. 5. Open up the audio program on your device and play your music
or other audio files. The audio file should play over the Bluetooth® Fan
Speakers.
2. 6. When done playing/listening to your audio files, disconnect from
the Speaker by either turning OFF the fan, disconnecting Bluetooth®
wireless technology from your device (Smart Phone, Tablet, etc)
or simply walking away. The Bluetooth® wireless technology will
automatically disconnect when the device is out of range of the Speaker,
which should occur when device is approximately 10 meters (33 feet)
away from the Speaker.
To connect to the Bluetooth® wireless technology Speaker each
subsequent time (after initial connection is made):
1. The Sensonic™ Speaker can only play audio files from one Bluetooth®
wireless technology device at a time, therefore one device must be
DISCONNECTED (but not necessarily UNPAIRED) before using the
Speaker with another device.
2. If your Bluetooth® wireless technology device was DISCONNECTED but
not UNPAIRED from the Speaker last time it was used, then it should
automatically connect next time the device is within range of the
Speaker, unless the Speaker is already CONNECTED to another device.
a. If your device does not CONNECT automatically with the
Speaker, then find your “Paired Devices” or similar list and
TAP on “Sensonic Vent Fan” to reconnect with the Sensonic™
Speaker.
3. If your Bluetooth® wireless technology device was UNPAIRED from the
Speaker after the last time it was used, you must follow the connection
procedure in the previous section for PAIRING your device with the
Speaker.
4. Open up the audio program on your device and play your music or
other audio files. The audio file should play over the Bluetooth® wireless
technology Fan Speakers.
5. When done playing/listening to your audio files, disconnect from
the Speaker by either turning OFF the fan, disconnecting Bluetooth®
wireless technology from your device (Smart Phone, Tablet, etc)
or simply walking away. The Bluetooth® wireless technology will
automatically disconnect when the device is out of range of the Speaker,
which should occur when device is approximately 10 meters (33 feet)
away from the Speaker.
MODEL SPK110
WARRANTY
Limited Warranty
Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser of its product (“you”) that the product
(the “Product”) will be free from material defects in the Product or its workmanship for a period of three (3) years from the date of original purchase.
The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited warranty shall
be the remainder of the original warranty period.
This warranty does not cover speed controls, fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof caps, wall caps
and other accessories for ducting that may be purchased separately and installed with the Product. This warranty also does not cover (a)normal maintenance and service, (b)normal wear and tear, (c)any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence, accident,
improper or insufficient maintenance, storage or repair (other than repair by the Company), (d)damage caused by faulty installation, or installation or use
contrary to recommendations or instructions, (e)any Product that has been moved from its original point of installation, (f)damage caused by environmental
or natural elements, (g)damage in transit, (h)natural wear of finish, (i)Products in commercial or nonresidential use, or (j)damage caused by fire, flood
or other act of God. This warranty covers only Products sold to original consumers in the United States by the Company or U.S. distributors authorized by
the Company.
This warranty supersedes all prior warranties and is not transferable from the original consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective products. The foregoing warranties
are exclusive and in lieu of any other warranties, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the period specified for the express warranty above. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is for the sole purpose of identifying it and shall
not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if
any provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the
remainder of such provision or the other remaining provisions of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge,
any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The
Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation
and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to the
Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible for damage in transit. The Company
reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement process. Such
Products and parts will be comparable in function and performance to an original Product or part and warranted for the remainder of the original warranty
period.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT THE COMPANY’S
OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE
OBLIGATION. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF
OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of field
service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver
of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with the
Company’s prior written permission.
How to Obtain Warranty Service: To qualify for warranty service, you must (a)notify the Company at the address or telephone number stated below within
seven (7)days of discovering the covered defect, (b)give the model number and part identification and (c)describe the nature of any defect in the Product
or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty, then the terms of the Company’s most current written limited warranty for your particular product will control.The most current limited
written warranties for the Company’s products can be found at www.broan.com .
Broan-NuTone LLC 926 West State Street Hartford, WI 53027
www.broan.com 800-637-1453
Page 6
Loading...