Broan QS2 User Manual

ALLURE® QS2 SERIES

RANGE HOOD

ALLURE QS2 SERIES RANGE HOOD

READ AND SAVE THESE INSTRUCTIONS

FOR DOMESTIC COOKING ONLY

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you already

know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust hazard-

3. To avoid motor bearing damage and noisy and/or unbalanced

4. For best capture of cooking impurities, your range hood should

5. Please read specification label on product for further information

Installer: Leave this manual with the homeowner.

Homeowner: Operating and Cleaning information on page 6.

NOTE If hood is to be installed Non-Ducted:

TABLE OF CONTENTS

This manual is divided into sections as follows:

“PREPARE HOOD LOCATION”

Run ductwork from roof or wall cap, and electrical wiring from

“PREPARE THE HOOD” Get your hood ready for installation

“CONNECT WIRING”

Make electrical wiring connections to hood

“INSTALL HOOD” Secure hood to cabinet and ductwork - install bulbs and filters

“OPERATION” How to use the hood controls

“CLEANING” Keep your hood in top working condition

“SERVICE PARTS”

Part numbers and exploded view of hood components

“WARRANTY” One-year limited warranty and how to contact us

Page 1

Patent No.:

US D450, 829 S

ous or explosive materials and vapors.

impellers, keep drywall spray, construction dust, etc. off power unit.

be mounted so that the top of the hood is 24-30” above the cooking surface.

and requirements.

Purchase a set of (2) non-ducted filters from your

local distributor or retailer and attach them to the aluminum mesh filters.

service panel - to installation location

ALLURE

PREPARE HOOD LOCATION PREPARE THE HOOD

QS2 SERIES

RANGE HOOD

Page 2

ROOF CAP

SOFFIT

CABINET

HOODHOOD

24" - 30" ABOVE COOKING SURFACE

3¼" X 10"

(For vertical

discharge)

HOUSE WIRING (Top or Back of hood)

WALL CAP

3¼" X 10" DUCT (For horizontal discharge)

1 Determine whether hood will discharge vertically (3¼” x 10”),

or horizontally (3¼” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows.

2 Use diagrams, below, for proper placement of ductwork and

electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.

HOOD MOUNTING SCREWS (4)

(30" hood)

(36" hood)

(42" hood)

CABINET FRONT

13 16 19

3¼” X 10”

VERTICAL DUCTING

(30" hood)

(36" hood)

(42" hood)

7½"

CABINET BOTTOM

5¼"

VERTICAL DUCT

ACCESS HOLE

1¼"

5¼"

10½"

1½"

ELECTRICAL

WOOD SHIMS

(recessed-bottom

cabinets only)

WOOD SHIMS

(recessed-bottom

cabinets only)

CENTER

LINE

CABINET FRONT

ACCESS HOLE

(in cabinet bottom)

3¼” X 10”

HORIZONTAL DUCTING

¾"

FILTERS

1 Remove tape holding Filters in place. Pull down on filter

tabs or finger holes and lift filters out. Set filters aside.

TEFLON®-

COATED

BOTTOM

COVER

(Held in

place with

2 screws)

2 Remove Teflon®-coated bottom cover from hood. Set

cover and mounting screws aside.

Teflon® is a registered trademark of DuPont.

DAMPER/

DUCT

CONNECTOR

HORIZONTAL DUCT

CABINET BOTTOM

HOOD

MOUNTING

SCREWS (4)

3¾"

16 16 16

" " "

5¼"

(30" hood) (36" hood) (42" hood)

ACCESS HOLE

CENTER

LINE

5¼"

7½"

ACCESS HOLE

(30" hood) (36" hood) (42" hood)

ELECTRICAL

(in wall)

3 Run house wiring between service panel and hood location.

3 Remove Damper/Duct Connector from inside the hood.

Set connector aside - with mounting screws and parts bag.

ALLURE® QS2 SERIES

PREPARE THE HOOD PREPARE THE HOOD

AIR CHUTE

6 Remove Air

Chute - held in place with one (1) screw.

NOTE: Be care-

ful not to disconnect any wires.

RANGE HOOD

Page 3

ELECTRICAL

CABLE CLAMP

4 Remove either top or back wiring knockout and install ap-

proved Electrical Cable Clamp.

Ducted Installation - Skip to Step 11.

The following Steps (5 thru 10) are for NON-DUCTED INSTALLATION ONLY.

(3) #8 SCREWS

(2) #8 SCREWS

5 Remove Light Panel - held in place with (3) #8 screws

and (2) #8 screws. Disconnect light assembly wire harness (white connector).

PANEL

LIGHT

7 Remove Baffle

from air chute. Tabs will disengage from Slots.

8 Rotate baffle. Reinsert

baffle into air chute (as shown) so that baffle fits all the way into into air chute. An audible “click” will be heard when fully installed. This will direct air flow through the non-ducted slots on top of hood.

SLOTS

BAFFLE

TABS

SUPPORT FIN

9 Re-install air chute and screw,

re-connect wire harness, and replace light panel.

NOTE: Be careful not to trap wires between Support Fin

and light panel.

+ 5 hidden pages