Broan QS142BL, QS142WW, QS142BC, QS142AA, QS130AA Installation Guide

...

ALLU TM

ALLURE TM QS1 SERIES

RANGE HOOD

Page 1

Patent No.: US D450, 829 S

FOR DOMESTIC

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or

telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American

Society of Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall orceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10. This unit must be grounded.

TO REDUCETHE RISK OFA RANGETOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCETHE RiSK OF INJURYTO PERSONS INTHE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,then turn off the burner. BE CAREFULTO PREVENT BURNS.

If the flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

2. NEVER PICK UPA FLAMING PAN --You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if: A. Youknow you have a Class ABC extinguisher and you already

know how to operate it.

B. The fire is small and contained inthe area where it started. C. The fire department is being called.

D. You can fight the fire with your back to an exit. * Based on "Kitchen Fire Safety Tips" published by NFPA.

COOKING ONLY.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power

unit.

3. For best capture of cooking impurities, your range hood should be mounted so that the top of the hood is 24-30" above the cooking

surface.

4. Please read specification label on product for further information and requirements.

Installer: Leave this manual with

the homeowner.

Homeowner: Operating and

Cleaning information on page 5.

[_ If hood is to be installed Non-Ducted:

Purchase a set of (2) non-ducted filters from your local distributor or retailer and attach them to the

aluminum mesh filters.

TABLE OF CONTENTS

This manual is divided into sections as follows:

"PREPARE HOOD LOCATION" Run ductwork from roof or wall cap, and electrical wiring from

service panel - to installation location "PREPARETHE HOOD"

Get your hood ready for installation "CONNECT WIRING"

Make electrical wiring connections to hood "INSTALL HOOD"

Secure hood to cabinet and ductwork - install bulbs and filters

"OPERATION" How to usethe hood controls

"CLEANING" Keep your hood in top working condition

"SERVICE PARTS" Part numbers and exploded view of hood components

"WARRANTY" One-year limited warranty and how to contact us

ALLURE TM QS1 SERIES

RANGE HOOD

Page 2

PREPARE HOOD LOCATION PREPARE HOOD LOCATION

ROOF CAP

SOFFIT

CABINET_._

31/4'' X 10" or

7" ROUND DUCT HOOD MOUNTING SCREWS (4)

(Forverfical 1315/16"(30"hood)

discharge) 1615/16``(36" hood)

HOUSE WiRiNG

or Back of hood)

24" -30" ABOVE COOKING SURFACE

Determine whether hood will discharge vertically (3W' x 10"

or 7" Round), horizontally (3W' x 10" only) or non-ducted. For

vertical or horizontal discharge, run ductwork between the

hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows.

El Use for of ductwork and

diagrams, below, placement

electrical cutout in cabinet or wall. For a non-ducted installa-

tion, DO NOT cut a duct access hole.

HOOD MOUNTING SCREWS (4) VERTICAL DUCTING

1315/16" (30" hood) 1615/16" (36" hood) 1315/16" (30" hood)

1915/16" (42" hood) "--_ _-" 1615/16" (36" hood)

1- CABINET FRONT 1915/16"(42"hood)

) 1 ii _,

!J CABINET BOTTOM I 4--5 W'---D*-- 5_A'_--_

proper

1 !

i,:1 _ VERTICAL DUCT , 2"

'.!:| 5" .--L ACCESS HOLE

3W' X 10" DUCT (For horizontal discharge)

31A" X 10"

i 7"ROUND

VERTICALDUCTING i

1 315/16"(30"hood)

(42" hood)

FRONT

CABINET BOTTOM

ACCESS HOLE FOR7"ROUND

DUCT

WOOD SHIMS _ ELECTRICAL

(recessed-bottom CENTER (in cabinet bottom)

cabinets only) LiNE

El Run house wiring between service panel and hood location.

(36"hood)

ACCESS HOLE

PREPARE THE HOOD

7" ROUND

DUCT PLATE

WOOD SHIMS

(recessed-bottom

cabinets only)

WOOD SHIMS j 31,4'' X 10" i

(recessed-bottom HORIZONTAL DUCTING

cabinets only)

MOUNTING

SCREWS (4)

t t ELECTRICAL t

CENTER (in cabinet bottom)

LINE

CABINET FRONT

j 1/8" 3_"

ACCESS HOLE

Remove 7" Round Duct Plate from top of hood. Set duct

plate aside - with mounting screws.

FILTERS

El Remove Filters in Pull down filter

tabs and lift filters out. Set filters aside.

tape holding place.

ALLURE TM QS1 SERIES

RANGE HOOD

Page 3

PREPARE THE HOOD

Remove Damper/Duct

Connector from inside the hood.

Set connec-

tor aside - with

mounting screws and parts bag.

DAMPER/DUCT

CONNECTOR

Remove Wir=

Cover from

inside the hood. Set cover and

mounting screw aside.

WIRING

COVER

PREPARE THE HOOD

AIR CHUTE

Remove Air

Chute- held in place with one

(1) screw.

NOTE: Be care- ful not to discon-

nect any wires.

El Remove Baffle

from air chute.

Remove either

top or back wir-

ing knockout and install approved

Electrical Cable

Clamp_.

ELECTRICAL CABLE CLAMP

Non-Ducted installation - Skip to "Connect

Wiring"section.

(3) #8 SCREWS LIGHT

The following Steps (6 thru

13) are for

DUCTED

_!iiii;

iNSTALLATiON

ONLY.

PANEL

Rotate baffle. Re-

insert baffle into air

chute (as shown) so that baffle tabs fit all

the way into slots in air chute. An audible

"click" will be heard when fully installed.

This will close off the air flow through

the non-ducted slots on top of hood.

BAFFLE

SLOTS

BAFFLE

TABS

El Remove L_ght Panel - held in place with (3) #8 screws

and (2) #8 screws. Disconnect light assembly wire harness (white connector).

Re-install air chute, re-connect wire harness, and replace light panel.

NOTE: Be careful not to trap wires

between _ort fin and light panel.

SUPPORT FIN

ALLURE TM QS1 SERIES

RANGE HOOD

Page 4

PREPARE THE HOOD

TOP RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼" x 10"

Vertical & for 7"Round

Discharge)

REAR

RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼"x 10" Horizontal Discharge)

[_ Remove appropriate Duct Knockout(s) from or back of

hood.

UPTO 1"

SIDE-TO-SIDE ADJUSTMENT

TAPE EDGE

SEMI-CIRCULAR

DUCT KNOCKOUT

(Remove for 7"Round

Discharge)

top

TOP/BAC K

CONNECT WIRING

_lb WARNING: To reduce the risk of electric shock,

[_ Connect House to hood. Use of

make sure power is switched off at the service panel. Lock or tag service panel to prevent power

from being switched on accidentally.

HOUSE

WIRING

(120 VAC)

CARDBOARD

to protect

cooktop)

Wiring (120VAC) a piece

Cardboard to protect the cooktop, if necessary.

PIVOT

31_'' x 10" Ducted Discharge Only: Attach Damper/Duct Connector over knockout opening. Make sure damper Pivot

is nearest to Top/Back Edg#_ of hood. Remove _ from

damper flap.

7" Round Ducted Discharge Only: Re-install 7" Round Duct

Plate removed in Step #1 under "PREPARE THE HOOD"

section. Install a 7" round damper (purchase separately).

Damper flap must open freely in direction of air flow (away

from range hood).

To accomodate off-center ductwork, the Damper/Duct Connector can be installed up to 1-inch on either side of

hood center or the 7" Round Duct Plate can be installed

up to Y2" on either side of hood center. In extreme off-center installations, one end of the duct connector may need to be trimmed

to clear the electrical cable clamp.

DAMPER/DUCT

CONNECTOR

(Vertical discharge

position shown)

GREEN

GROUND

SCREW

El Connect house black to hood black wire, house white to hood

white wire, and house ground under Green Ground Screw. Securely tighten cable clamp onto house wiring.

Replace wiring cover.

+ 8 hidden pages