Broan QP342BL, QP330SS Installation

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

EVOLUTIONTM 3 QP3 Series Range Hoods

READ AND SAVE THESE INSTRUCTIONS

FOR DOMESTIC COOKING ONLY

Page 1

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. This product may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning.

6. When cutting or drilling into wall or ceiling, electrical wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. Use only metal ductwork.

9. Do not use this fan with any solid-state speed control device.

10. As an alternative, this product may be installed with the ULapproved cord kit designated for the product, following instructions packed with the cord kit.

11. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL

FIRE DEPARTMENT.

THE

do not

damage

WARNING

2. NEVER PICK UP A FLAMING PAN — You may be burned or spread the fire.

3. DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you

already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. Yo u can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. F o r indoor use only.

2. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced impeller, keep drywall spray, construction dust, etc., off power unit.

4. Do not use over cooking equipment greater than 60,000 BTU/hr. as the blower motor will shut down intermittantly.

5. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced.

6. The top of the hood MUST NOT BE LESS than 24” and at a maximum of 30” above impurities.

7. This hood is not intended to be used as a shelf.

8. Please read specification label on product for further information and requirements.

NOTE If hood is to be installed non-ducted: Purchase a set of (2) non-ducted filters for 30” wide

hoods (Model BPPF30) & 36” wide hoods (Model BPPF36) or a set of (3) non-ducted filters for 42” wide hoods (Model BPPF42) from your local distributor or retailer and attach them to the aluminum mesh filters.

Installer: Leave this manual

with the homeowner.

Homeowner: Cleaning, Maintenance and

Operating instructions on page 2.

cookt

op for best capture of cooking

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 2

CONTENTS

INCLUDED WITH THE HOOD:

GREASE

(2 - FOR 30” & 36” HOODS)

(4)

HALOGEN

BULBS

(3) WIRE NUTS

(9)

#8 X 1/4”

DUCT

CONNECTOR

SCREWS

FILTERS

3 - FOR 42” HOODS)

(1) PARTS BAG CONTAINING:

CUP TOOL

#10 X 5/8”

RD. HD.

MOUNTING

SCREWS

(1)

BULB

SUCTION

(5)

(1) 3¼” X 10”

DAMPER / DUCT

CONNECTOR

(1) 7” ROUND

DUCT

CONNECTOR

#8 X 5/16” MACHINE SCREWS

#8 WASHERS

FOR NON-DUCT

DIVERTER

(1)

NON-DUCT

DIVERTER

(2)

OPERATION

Always turn the hood ON before cooking in order to establish an air flow in the kitchen. After turning off the range, let the hood run for a few minutes to clear the air.

Operate the hood as follows:

NOTE

The

and buttons are used to adjust and toggle the menu

and timer settings.

LIGHT (3-Pushbutton Switches 4-light Settings)

Turns the light on the low setting and activates a green indicator above the button. Pressing the the night time setting and illuminates the

Turns the light on the medium setting and activates a green

indicator above the button.

Turns the light on the high setting and activates a green indicator above the button. Pressing and holding the same light button again will turn the lights

off. When the night time setting is active, pressing and holding the low

light setting button will turn the night time setting off.

button a second time activates

indicator.

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean filter, fan and grease-laden surfaces. Use only a clean cloth and mild detergent solution on stainless and painted surfaces.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions - but this will not affect filter performance. This discoloration is not covered by the warranty.

Clean the non-duct recirculating filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special “Clean Sense” feature indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The “Clean Sense” feature works best when facing toward the cooking surface. Change the non-duct recirculating filters every 6 months. For replacement non-duct recirculating filters - purchase S99010353 or Model BPPF30 for 30 wide hoods”, S99010354 or Model BPPF36 for 36” wide hoods, or S99010360 or Model BPPF42 for 42” wide hoods.

The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor be replaced.

Use 120 V, 50 W, shielded halogen bulbs - MR16 with GU10 base.

with the

exact service motor. The impeller should also

FAN (3-Pushbutton Switches 4-fan speeds)

Turns the fan on the low speed and activates a green indicator

above the button.

Turns the fan on the medium speed and activates a green indicator above the button.

Turns the fan on the high speed and activates a green indicator above the button. Pressing the vates the boost fan speed and illuminates the Pressing and holding the same fan button again will turn the fan off. When the boost speed is active, pressing and holding the high

speed button will turn the boost speed off.

NOTE

This hood utilizes an offset blower design to achieve greater performance and lower sound levels. As a result, you may notice that cooking impurities are more attracted to one side or appear to be pulled-in faster than they appear on the opposite side. This is completely normal. The hood has been designed and tested to provide good capture of cooking impurities and odors under all normal cooking conditions regardless of the cooking location on the cooktop. Please note that cooking on the rear burners will always result in the best capture of cooking impurities, regardless of the hood design.

button a second time acti-

indicator.

10-MINUTE DELAY OFF

When your hood fan is on (any speed) press the activate the delay off feature. When activated, the hood fan will automatically turn off after 10-minutes has elapsed. The delay feature is active when the following appear on the LED screen: A green indicator illuminated above the delay meric countdown “10-0”, and a clockwise rotating LED. The delay button can be pressed once again, to stop the delay countdown. Pressing the Pressing and holding the button will turn off the feature.

TIMER

Press the

and buttons to reduce or advance the timer setting to

the the desired duration. When the desired timer setting is reached, allow 3 seconds without pressing any additional button or press the the countdown will be displayed on the LED screen along with an green indicator above the reached “0:00”, an audible beep will be heard. The beep will continue until the timer button timer countdown can be stopped at any time by pressing the

the timer countdown. Pressing and holding the turn off the feature. Note that when both the timer and delay off features are active together, the timer function will be illuminated on the LED display, and the delay off countdown will be active, but not displayed.

button once again. The timer will then activate, and

once again. Pressing the button again will resume

button again will resume the delay countdown.

button to activate the timer setting feature. Use

button. After the timer has

is pressed once again. The

button to

button, a nu-

button will

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 3

CLOCK SETTING

Press the LED screen. Use the hours for the clock. A small indicator will illuminate in the left corner of the LED screen to designate “pm”. After the hours are set, press the lection. The minutes will begin blinking in the LED screen. Use

and buttons to set the minutes. Press the button

the again to advance the menu to select “display” settings.

DISPLAY (default from factory - display ON)

The LED screen will display the display feature -d-. Use the or button to toggle the LED screen on (d on) or off (doFF). When the display off (doFF) feature is selected, the LED display clock illumination is disabled. Press the vance the menu to select the “Sleep” setting.

SLEEP MODE (default from factory - OFF)

The LED screen will display the “Sleep” feature -S- . Use the or button to toggle the Sleep feature on (S on) or off (S off). When the Sleep on (S on) feature is selected, the LED screen and fan/light LED indicators are disabled. The ambient light sensor, delay-off and timer features will also be disabled. All controls for the fan and light operation, including Heat Sentry, are still active. Press the to select the “Ambient Light Sensor” setting. Note: To access the feature menu when the Sleep Mode is active, press and hold the

button for 2 seconds.

button once, the “hours” will begin blinking in the

and buttons to set the appropriate

button to advance the menu to the minute se-

button again to ad-

button again to advance the feature menu

FEATURE MENU

Your hood offers many settings that can be accessed and adjusted by scrolling through the feature menu. Your hood fan must be off to be able to activate and access the feature menu. Pressing the feature menu. Pressing the menu is active will scroll through the various features that can be adjusted/set. When the feature menu is active, if a button is not pressed within 10 seconds or after scrolling through all menu settings, the feature menu will automatically be exited, and all selected settings will be saved. A green indicator above the icon will illuminate when the feature menu is active. The following features can be adjusted sequentially:

button when the hood fan is off will activate the

button again when the feature

AMBIENT LIGHT SENSOR (default from factory - Level 1 ON)

There are two level settings for the ambient light sensor. When either of the two settings is active, the light sensor will detect a low level of light in your kitchen, and will automatically turn the task lights on the hood to the night time setting. The other light settings are still functional. If selected when the ambient light sensor is active, they will temporarily overide the ambient light sensor until they are turned off. The level 1(Aon1) ambient light sensor setting will require your kitchen to be more dark than the level 2 (Aon2) setting before activating the night time setting. The LED screen will display the ambient light sensor function

-A-. Use the Aon1, Aon2, or AoFF. The Off (AoFF) setting deactivates the automatic ambient light sensor feature so the night time light operation is manual.

Note that the feature menu can be exited any time by not pressing any button(s) for 10 seconds or by scrolling through the entire feature menu.

or button to select the light sensor setting

HEAT SENTRY SYSTEM

This range hood is equipped with an advanced Heat Sentry system that monitors excessive temperature and automatically adjusts the fan to the appropriate setting.

1) If the fan is on, the Heat Sentry system will increase the fan setting when the temperature is elevated. If the temperature continues to rise, the Heat Sentry system will continue to increase the fan setting until the temperature is stabilized or reduced. The flashing light above the fan button shows the Heat Sentry system fan setting. Once the temperature has reduced, the Heat Sentry system will change the fan to the original setting.

2) If the fan is off, the Heat Sentry system will automatically turn the fan on to its highest speed when the temperature is above normal. When the Heat Sentry system is on, the light above the high speed fan button will flash on and off. After the temperature has lowered to normal, the fan speed will be reduced until the temperature has stabilized, then the fan will turn off.

Note: Canadian version does not have this function.

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 4

MAKE-UP AIR DAMPER

The hood is compatible with Broan Make-Up Air Damper Model MD6T or Model MD8T (optional). Purchase separately.

Make the connection to the Make-Up Air Damper with low voltage wiring, as shown. See Make-Up Air Damper instructions for additional information.

BACK OF HOOD

LOW-VOLTAGE CONNECTOR FOR MAKE-UP AIR DAMPER

RANGE

HOOD

LOW-VOLTAGE

WIRES

MAKE-UP AIR

DAMPER

FUSES

RANGE HOOD CONTROL BOARD

MAIN

FUSE

LIGHT

FUSE

The Range Hood Control Board contains a Main Fuse and a Light Fuse to protect the controls from power surges. If a fuse has opened (blown), the green fan setting or light setting indicators will not operate properly when the fan or light buttons are pressed, and the fan and lights will not turn on.

New fuses can be purchased at your local electronic supply store. Use 8A, 120V, 5 mm diameter, 20 mm long, fast-acting, cartridgetype fuses.

To replace a fuse:

1. Disconnect power at service entrance.

2. Remove filters and bottom pan.

3. Remove and inspect fuse. If it is not open (blown), additional diagnostics are needed.

120

VAC

DAMPER

MOTOR

REMOTE CONTROL

The hood is compatible with Broan RF Remote Control Model BCR1 (optional). Purchase separately.

PREPARE HOOD LOCATION

ROOF CAP

SOFFIT

CABINET

HOODHOOD

24" - 30" ABOVE COOKING SURFACE

3¼" X 10" or

7" ROUND DUCT

(For vertical

discharge)

HOUSE WIRING (Top or Back of hood)

WALL CAP

3¼" X 10" DUCT (For horizontal discharge)

1 Determine whether hood will discharge vertically (3¼”

x 10” or 7” Round), or horizontally (3¼” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows.

MODELS QP330BL • QP330SS • QP330WW

VERTICAL DUCT

ACCESS HOLE

¾"

5¼"

CENTER

LINE

HOOD MOUNTING SCREWS (5)

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

WOOD SHIMS

(recessed-bottom

cabinets only)

CABINET FRONT

CABINET BOTTOM

" (42" hood)

4½"

11"

" (42" hood)

" (36" hood)14

" (36" hood)

" (30" hood)11

" (30" hood)

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 5

2 Use the proper diagram below, for placement of ductwork

and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.

3¼” X 10”

VERTICAL DUCTING

3¼” X 10”

WOOD SHIMS

(recessed-bottom

cabinets only)

CABINET FRONT

HORIZONTAL DUCTING

35/8"

13/8"

/8"

PREPARE THE HOOD

3 Remove parts bag from inside the foam packaging end

cap.

4 Remove all protective polyfilm from the hood (stainless

steel hoods only).

(1)

PULL

DOWN

ALUMINUM

FILTERS

(2) LIFT OUT

5 Remove the Aluminum Filters from the hood.

CABINET

BOTTOM

" (30" hood)

" (36" hood)

" (42" hood)

HOOD

MOUNTING

SCREWS (5)

HOOD MOUNTING SCREWS (5)

" (30" hood)

" (36" hood)

" (42" hood)

45/8"

Note the extra wood shim and mounting screw near the

cabinet front, on the cabinet center line.

HORIZONTAL DUCT

ACCESS HOLE

5¼"

CENTER

LINE

8" DIA.

HOLE

7-IN. ROUND

DUCT

ACCESS

HOLE

5¼"

67/8"

" (30" hood)11

" (36" hood)14

" (42" hood)17

" (30" hood)11

" (36" hood)14

" (42" hood)17

7/8"

11"

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

ELECTRICAL

ACCESS

HOLE

(in wall)

MAKE-UP AIR

DAMPER ELECTRICAL

CONNECTION HOLE

(in wall)

7-IN. ROUND

DUCTING

/8"

21/8"

/8"

6 Remove 6 Screws holding Bottom Pan to hood. Set bot-

tom pan and screws aside.

DAMPER /

DUCT CONNECTOR

7 Remove 2 Screws holding Damper / Duct Connector

to hood. Remove damper/duct connector from inside the hood.

FOR DUCTED INSTALLATIONS - Skip to Step 12.

NON-DUCT

DIVERTER

8 NON-DUCTED INSTALLATION ONLY:

From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers.

SCREWS

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 6

11 NON-DUCTED INSTALLATION ONLY:

Purchase a set of (2) non-ducted filters for 30” wide hoods (Model BPPF30) & 36” wide hoods (Model BPPF36) or a set of (3) non-ducted filters for 42” wide hoods (Model BPPF42) from your local distributor or retailer. Attach the non-ducted filters to the aluminum mesh filters following instructions packed with the non-ducted filters.

FOR NON-DUCTED INSTALLATIONS - Skip to “INSTALL THE HOOD”.

7” ROUND KNOCKOUT PLATE (also

remove 3¼” x 10”

vertical plate)

3¼” X 10”

VERTICAL

3¼” X 10”

HORIZONTAL

KNOCKOUT

PLATE

KNOCKOUT

PLATE

NON-DUCT

PLATE

NON-DUCT

PLATE

SLOT

NON-DUCT

PLENUM

9 NON-DUCTED INSTALLATION ONLY:

Remove 2 Screws holding Non-Duct Plate to Non-Duct Plenum and remove plate.

SCREWS

NON-DUCT

PLATE

10 NON-DUCTED INSTALLATION ONLY:

Insert short end of Non-Duct Plate into Non-Duct Plenum Slot. Attach with 2 Screws removed in Step 9.

12 DUCTED INSTALLATION ONLY:

Remove 3¼” x 10 vertical, 3¼” x 10” horizontal, or 7-inch round knockout plate(s) as appropriate for your ducting method.

3¼” X 10”

TOP/BACK

DAMPER / DUCT CONNECTOR

EDGE OF

HOOD

7” ROUND

DUCT

PLATE

13 DUCTED INSTALLATION ONLY:

Attach 3¼” x 10” Damper/Duct Connector (if using 3¼” x 10” duct) or 7” Round Duct Plate (if using 7-inch round duct) over the knockout opening.

Notes:

To accomodate off-center ductwork, the 3¼” x 10” damper/ duct connector can be installed up to ½” on either side of the hood center and the 7” round duct plate can be installed up to ½” on either side of the hood center.

Install the 3¼” x 10” Damper/Duct Connector with the Damper Flap Pivot nearest the Top/Back Edge of Hood.

DAMPER

FLAP

PIVOT

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 7

INSTALL THE HOOD

WARNING

To reduce the risk of electrical shock, switch power off at service panel. Lock or tag service panel to prevent power from being switched on accidentally.

ELECTRICAL

WIRING BOX

COVER

ELECTRICAL

POWER

CABLE

KNOCKOUT

14 Remove Electrical Wiring Box Cover from inside

of hood and appropriate Electrical Power Cable

Knockout from top or back of hood.

CONNECT THE WIRING

GROUND

SCREW

HOUSE

POWER CABLE

18 Connect House Power Cable to range hood wiring -

BLACK to BLACK, WHITE to WHITE, and GREEN or BARE WIRE to Ground Screw. Replace electrical wiring box cover.

19 Re-attach Bottom Pan with 6 Screws removed in Step 6.

INSTALL LIGHT BULBS

HOUSE

POWER CABLE

15 Run House Power Cable between service panel and hood

location. Attach power cable to hood using appropriate clamp.

16 Hang hood from (4) mounting screws driven part-way into

cabinet locations (shown in illustrations under “PREPARE HOOD LOCATION”). Mounting screws are included in parts bag. Slide hood back towards wall until mounting screw heads are engaged in narrow end of keyhole slots in top of hood. Tighten screws securely. Add 5th mounting screw in center hole in hood and tighten securely.

17 DUCTED INSTALLATION ONLY:

Connect ductwork to hood and use duct tape to make joints secure and air-tight. Make sure the damper / duct connector enters the ductwork and that the damper opens and closes freely.

SUCTION

CUP TOOL

HALOGEN

BULB

(2)

ROTATE

CLOCKWISE

LIGHT PANEL

SCREWS

CAUTION: Bulbs may be hot. Refer to bulb packaging for further information.

20 Install (4) Halogen Bulbs (included with hood). Use 120

V, 50 W, shielded halogen bulbs - MR16 with GU10 base.

NOTE: Suction Cup Tool (included with hood) can be

used to install and remove light bulbs.

Align pins on bulb with large diameter opening on socket,

then push bulb in towards hood and rotate clockwise until firmly seated.

The position of the bulb socket (depth) is adjustable and

may require adjustment when: a) certain brands of bulbs are difficult to install. b) the bulb protrudes too far below the light panel.

(1)

PUSH IN

LIGHT PANEL

LAMP SOCKET

BRACKET

LIGHT

LIGHT PANEL

PANEL

To change the depth of bulb sockets:

- Remove bottom pan (See Step 6).

- Remove 2 Light Panel Screws and Light Panel. Set

screws aside.

- Loosen 2 Screws holding Lamp Socket Bracket to

- Adjust socket/bracket to desired depth.

- Re-tighten screws securely.

- Re-attach light panel and bottom pan.

21 DUCTED INSTALLATION ONLY:

WARRANTY

Light Panel.

Re-install aluminum filters removed in Step 5.

NON-DUCTED INSTALLATION ONLY:

Install aluminum filters and non-ducted filters - purchased

Install aluminum filters and non-ducted filters - purchased and assembled in Step 11.

and assembled in Step 11.

One Year Limited Warranty

Broan-NuTone warrants to the original consumer purchaser of its products that such

Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one

products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES,

(1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one year period, Broan-NuTone will, at its option, repair or replace, without

During this one year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and

charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS,

service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF

TUBES, HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does

CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have

not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other

been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended

than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.

installation instructions. The duration of any implied warranty is limited to the one year period as specified for the

The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty

express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

lasts, so the above limitation may not apply to you. BROAN-NUTONE’S OBLIGATION TO

BROAN-NUTONE’S OBLIGATION TO OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER

OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or

WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior

have other rights, which vary from state to state. This warranty supersedes all prior warranties.

warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or

To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c)

telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting

describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

warranty service, you must present evidence of the original purchase date. Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027

Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com 800-558-1711

www.broan.com 800-558-1711 Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario Canada L5T 1H9

Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario Canada L5T 1H9 www.broan.ca 877-896-1119 Rev. 08/2007

www.broan.ca 877-896-1119 Rev. 08/2007

One Year Limited Warranty

REPAIR OR REPLACE, AT BROAN-NUTONE’S

SCREWS

MODELS QP330BL • QP330SS • QP330WW

QP336BL • QP336SS • QP336WW QP342BL • QP342SS • QP342WW

Page 8

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

1 97017727 7” Round Duct Plate (includes mounting hardware)

1 97017727 7” Round Duct Plate (includes mounting hardware) 2 97018256 User Interface Assembly White (includes interface,

2 97018256 User Interface Assembly White (includes interface, nameplate, mounting hardware)

nameplate, mounting hardware) 97018257 User Interface Assembly Black (includes interface,

97018257 User Interface Assembly Black (includes interface, nameplate, mounting hardware)

nameplate, mounting hardware) 3 99528258 Nameplate, White

3 99528258 Nameplate, White 99528259 Nameplate, Black

99528259 Nameplate, Black 4 97018251 Capacitor Kit (includes wire nuts, mounting screw)

4 97018251 Capacitor Kit (includes wire nuts, mounting screw) 5 97018225 Light Panel RH White (includes mounting hardware)

5 97018225 Light Panel RH White (includes mounting hardware) 97018226 Light Panel RH Black (includes mounting hardware)

97018226 Light Panel RH Black (includes mounting hardware) 97018227 Light Panel RH Stainless (includes mounting hardware)

97018227 Light Panel RH Stainless (includes mounting hardware) 6 97018205 Filter Kit for 30” (2 per bag)

6 97018205 Filter Kit for 30” (2 per bag) 97018206 Filter Kit for 36” (2 per bag)

97018206 Filter Kit for 36” (2 per bag) 97018207 Filter Kit for 42” (3 per bag)

97018207 Filter Kit for 42” (3 per bag) 7 97018220 Blower Wheel (includes mounting nut)

7 97018220 Blower Wheel (includes mounting nut) 8 97018223 Motor Kit (includes motor, isolators, mounting hardware)

8 97018223 Motor Kit (includes motor, isolators, mounting hardware) 9 97017728 Damper / Duct Connector (includes mounting hardware)

9 97017728 Damper / Duct Connector (includes mounting hardware) 10 97018229 Light Panel LH White (includes mounting hardware)

10 97018229 Light Panel LH White (includes mounting hardware) 97018230 Light Panel LH Black (includes mounting hardware)

97018230 Light Panel LH Black (includes mounting hardware) 97018231 Light Panel LH Stainless (includes mounting hardware)

97018231 Light Panel LH Stainless (includes mounting hardware) 11 97017731

11 97017731 12 97018233 Lamp Socket Bracket

12 97018233 Lamp Socket Bracket 13 97018239 Bottom Pan 30” (includes mounting hardware)

13 97018239 Bottom Pan 30” (includes mounting hardware) 97018240 Bottom Pan 36” (includes mounting hardware)

97018240 Bottom Pan 36” (includes mounting hardware) 97018241 Bottom Pan 42” (includes mounting hardware)

97018241 Bottom Pan 42” (includes mounting hardware) 14 97018242 Non-duct Plenum (includes gasket & mounting hardware)

14 97018242 Non-duct Plenum (includes gasket & mounting hardware) 15 97018243 Non-duct Diverter (includes mounting hardware)

15 97018243 Non-duct Diverter (includes mounting hardware) 16 97018244 Non-duct Plate (includes mounting hardware)

16 97018244 Non-duct Plate (includes mounting hardware) 17 97018260 Circuit Board

17 97018260 Circuit Board 18 97018262 Transformer (includes mounting hardware)

18 97018262 Transformer (includes mounting hardware)

Not Shown

97018224 Parts Bag

Not Shown

97018224 Parts Bag

Not Shown

99010353

Not Shown

99010353

99010354

99010354 99010360

99010360

Not Shown

99526707 Suction Cup Tool

Not Shown

99526707 Suction Cup Tool

Not Shown

97018252 Heat Sensor

Not Shown

97018252 Heat Sensor

Not Shown

97018253 Fuse

Not Shown

97018253 Fuse

Not Shown

97018261 Ribbon Cable Kit (contains 3)

Not Shown

97018261 Ribbon Cable Kit (contains 3)

Order replacement parts by PART NO. - not by KEY NO.

Lamp Socket (includes lamp socket, wire nuts, mounting screws)

Non-Duct Filter Kit for 30” (2 charcoal filters and 8 filter clips)

Non-Duct Filter Kit for 30” (2 charcoal filters and 8 filter clips) Non-Duct Filter Kit for 36” (2 charcoal filters and 8 filter clips)

Non-Duct Filter Kit for 36” (2 charcoal filters and 8 filter clips) Non-Duct Filter Kit for 42” (3 charcoal filters and 12 filter clips)

Non-Duct Filter Kit for 42” (3 charcoal filters and 12 filter clips)

99527291C

+ 16 hidden pages