Broan BCS324SSC, BCS324WWC, BCS330SSC, BCS330WWC, BCS330BLC INSTALLATION INSTRUCTIONS AND OPERATION MANUAL
RANGE HOOD
Series: BCDA, BCS3, BCSM,
NCDA, NCS3 and NCSEK
INSTALLATION, USE
AND CARE MANUAL
Serial number:
99045652-101F
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Cleaning and Maintenance . . . . . . . . . . . . . . . . . 7
Motor
Grease Filters
Non-Ducted Recirculation Filters
Fan Blade
Stainless Steel Cleaning
Painted Finish Cleaning
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
Recommended Tools
and Accessories for Installation . . . . . . . . . . . . 8
Install Ductwork (Ducted Installations Only) . . . 8-9
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Prepare the Hood . . . . . . . . . . . . . . . . . . . . . . . 11-13
Prepare the Hood Location . . . . . . . . . . . . . . . . 14
EZ1 One-person Installation . . . . . . . . . . . . . 14-16
Install the Hood (EZ1 Brackets) . . . . . . . . . . . 17-18
Standard Installation . . . . . . . . . . . . . . . . . . . 19
Install the Hood (Standard Installation) . . . . . 20
Connect the Wiring . . . . . . . . . . . . . . . . . . . . . . 21
Light Bulbs
(BCS3, BCSM and NCS3 Series only) . . . . . . . 22
Install the Filters . . . . . . . . . . . . . . . . . . . . . . . . 22
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . 23-26
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . 27-31
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
INSTALLATION MANUAL
TABLE OF CONTENTS
2
READ AND SAVE THESE INSTRUCTIONS
!
Intended for domestic cooking only
!
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
For Broan range hoods, register your range hood online at www.broan.ca
For NuTone range hoods, register your range hood online at www.nutone.ca
!
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
• Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
• Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
• Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including
fire-rated construction.
• Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guidelines and
safety standards such as those published by the National Fire Protection
Association (NFPA) and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local code authorities.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
• Do not use this unit with any additional solid-state speed control device.
• To reduce the risk of fire, use only metal ductwork.
• This unit must be grounded.
• As an alternative, this product may be installed with the UL-approved cord
kit designated for the product, following instructions packed with the cord
kit.
• When applicable local regulations comprise more restrictive installation
and/or certification requirements, the aforementioned requirements prevail
on those of this document and the installer agrees to conform to these at
his own expense.
INSTALLATION MANUAL
SAFETY
3
!
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
b) Always turn hood ON when cooking at high heat or when flambeing food
(i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fan frequently. Grease should not be allowed to
accumulate on fan, filters or in exhaust ducts.
d) Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE
FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL
THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels — This could
cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
INSTALLATION MANUAL
SAFETY
4
!
CAUTION
• For indoor use only.
• For general ventilating use only. Do not use to exhaust hazardous or explosive materials
and vapors.
• To avoid motor bearing damage and noisy and/or unbalanced fan blade, keep drywall
spray, construction dust, etc. off range hood.
• Your hood motor has a thermal overload which will automatically shut off the motor if it
becomes overheated. The motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
• For best capture of cooking fumes, the bottom of the hood MUST NOT BE LESS than 18”
and at a maximum of 24” above the cooking surface.
• Always follows the cooking equipment manufacturer’s requirements regarding the
ventilation needs.
• To reduce the risk of fire and to properly exhaust air, be sure to duct air outside — Do not
exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.
• When installing, servicing or cleaning the unit, it is recommended to wear safety glasses
and gloves.
• Please read specification label on product for further information and requirements.
Operation
Always turn your hood on before you begin cooking to establish an air flow in the kitchen.
Let the blower run for a few minutes to clear the air after you turn off the range. This will help
keep the whole kitchen cleaner and fresher.
Operate the hood as follows:
BCS3 AND NCS3 SERIES
BLOWER SWITCH
I Turns blower on to LOW speed.
• Turns blower OFF.
II Turns blower on to HIGH speed.
BCSM SERIES
ON/OFF BLOWER PUSH BUTTON
When blower is OFF, push on this button to turn ON the blower at the last selected speed. Push on
this button again to turn OFF the blower.
NOTE: If there is no speed selected (all blower speed push buttons up), the blower will not turn ON.
In that case, press on the desired speed level push button to activate the blower.
BLOWER SPEED LEVEL PUSH BUTTONS
When blower is ON, change the blower speed by pressing on the push button corresponding to the
desired speed: one line for LOW, two lines for MEDIUM and three lines for HIGH speed.
ON/OFF LIGHT PUSH BUTTON
LIGHT SWITCH
I Turns light on to LOW intensity.
• Turns light OFF.
II Turns light on to HIGH intensity.
When lights are OFF, push once on this button to turn ON the lights at the last selected setting.
Push on this button again to turn OFF the lights.
LIGHT INTENSITY LEVELS PUSH BUTTON
Push on this button to change the light intensity (HIGH or LOW).
OPERATION
INSTALLATION MANUAL
5
NCSEK SERIES
BLOWER SWITCH
I Turns blower on to LOW speed.
• Turns blower OFF.
II Turns blower on to HIGH speed.
The LED modules included with this hood are the latest in LED cooktop illumination technology
specially designed to operate in the elevated temperatures of cooking - offering bright lighting and
lasting up to 25 times as long as a standard bulb and greater reliability than typical replacement
LED bulbs.
LIGHT SWITCH
I Turns light ON.
• Turns light OFF.
BCDA AND NCDA SERIES
BLOWER BUTTON
When blower is OFF, press this button to turn ON the blower at the last saved speed. If there was
no speed saved, the blower will be set on LOW speed.
NOTE: When LOW speed is activated from OFF, the blower starts on MEDIUM speed for a very
short lapse of time, and then resume to LOW speed.
To change the blower speed, press on this button again until the desired speed is reached (from
LOW to MEDIUM to HIGH speed to OFF). Each time a blower speed is activated, a beep is heard
and LED indicators light up to show the corresponding speed chosen (lower LED for LOW speed,
lower and center LEDs for MEDIUM speed and all LEDs for HIGH speed).
When blower is on (no matter the speed level), press and hold this button until the beep sound
ends; this will turn off the blower and save this blower speed to memory.
INSTALLATION MANUAL
OPERATION
6
LIGHT BUTTON
When lights are OFF, press once on this button to turn ON the lights at the last saved setting. If
there was no light setting saved, the lights will be set on LOW intensity. Press another time to set
the lights on HIGH intensity. Pressing another time after the HIGH setting will turn OFF the lights.
Each time the lights are turned ON, a beep is heard and LED indicators light up to show the
corresponding intensity chosen (lower LED for LOW and both LEDs for HIGH).
When lights are on (no matter the lighting level), press and hold this button until the beep sound
ends; this will turn off the lights and save the chosen light intensity.
The LED modules included with this hood are the latest in LED cooktop illumination technology
specially designed to operate in the elevated temperatures of cooking - offering bright lighting
and lasting up to 25 times as long as a standard bulb and greater reliability than typical
replacement LED bulbs.
FILTER CLEANING REMINDER
When it is time to clean the hood and filters (refer to Cleaning and Maintenance on page 7), the
3 blower button LED indicators will flash slowly for 30 seconds after turning the blower OFF. This will
happen every time the blower is turned OFF until the filter cleaning reminder has been reset. Once
the cleaning is done, reset the filter cleaning reminder indicators by pressing on blower button for
3 seconds during the 30 seconds the 3 blower button LED indicators flash slowly.
Cleaning and Maintenance
Proper maintenance of the Range Hood will assure proper performance of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If the motor bearings make
excessive or unusual noise, replace the motor with the exact service motor. The fan blade should
also be replaced.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm dishwashing detergent solution.
Clean all-metal filters using a non-phosphate detergent. Discoloration of the filters may occur if
using phosphate detergents, or as a result of local water conditions - but this will not affect filter
performance. This discoloration is not covered by the warranty. To minimize or prevent discoloration,
hand wash filters using a mild detergent.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every 3 to 6 months. Replace more often
if your cooking style generates extra grease, such as frying and wok cooking. Refer to installation
instructions included with non-ducted recirculation filters.
FAN BLADE
The fan blade should be cleaned frequently. Use a clean cloth soaked with warm detergent solution.
STAINLESS STEEL CLEANING
Do:
• Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish
detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
• You may also use a specialized household stainless steel cleaner.
Don’t:
• Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the hood. During construction/
renovation, cover the range hood to make sure no dust sticks to the stainless steel surface.
Avoid when choosing a detergent:
• Any cleaners that contain bleach will attack stainless steel.
• Any products containing: chloride, fl uoride, iodide, bromide will deteriorate surfaces
rapidly.
• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc.,
are highly explosive and should never be used close to a range.
PAINTED FINISH CLEANING:
Clean with warm water and mild detergent only. If discoloration occurs, use a finish polish such
as automotive polish. (DO NOT use rough abrasive cleaner or porcelain cleaner.)
CLEANING AND MAINTENANCE
INSTALLATION MANUAL
7
For ADA compliance installation guidelines, please visit www.broan-nutone.com
Recommended Tools and Accessories
for Installation
• Measuring tape
• Phillips screwdriver no. 2
• Flat blade screwdriver (to open knockout holes)
• Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole)
• 7/64” drill bit (to drill holes for EZ1 brackets mounting screws, not for BCS3 and NCS3 Series)
• 7” round duct plate, not included (for 7’’ round vertical ducting installation, part no.: SR680508)
• Wood shims (2) and wood screws (4) (required for standard installation to framed cabinet)
• Saw (to cut holes for ducted application)
• Sheet metal shears (ducted installation only, for duct adjustment)
• Pliers (ducted installation only, for duct adjustment)
• Metal foil duct tape (for ducted applications)
• Scissors (to cut metal foil duct tape)
• Pencil
• Wire stripper
• Strain relief, 1/2” diameter (to secure house wiring cable to the hood)
INSTALLATION MANUAL
INSTALLATION
8
Install Ductwork (Ducted Installations Only)
ROOF CAP
SOFFIT
CABINET
HOOD
18" MIN - 24" MAX
ABOVE
COOKING SURFACE
NOTE: Distances over 24” are at the installer and user discretion.
1 ] Determine whether hood will discharge vertically (3¼” x 10” or 7” round),
or horizontally (3¼” x 10” only).
2 ] Decide where the ductwork will run between the hood and the outdoors.
3 ] The ducting from this fan to the outside of the building has a strong effect on the air flow,
noise and energy use of the fan. Use the shortest, straightest duct routing possible for best
performance, and avoid installing the fan with smaller ducts than recommended. Insulation
around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing
ducts may not achieve their rated airflow. Refer to the table on next page to help you plan the
most efficient installation.
4 ] Install wall cap or roof cap (sold separately); ensure there is no leak in house insulation.
Connect metal ductwork to cap and work back towards the hood location. Use 2” metal foil
duct tape to seal the joints between ductwork sections.
3¼" X 10" OR
7" ROUND DUCT
(FOR VERTICAL
DISCHARGE
HOUSE WIRING
(TOP OR BACK OF HOOD)
3¼" X 10" DUCT
(FOR HORIZONTAL DISCHARGE)
)
WALL CAP
Maximum Duct Lengths Recommended
VERTICAL EXHAUST
VERTICAL EXHAUST
to Achieve 80% Exhaust Efficiency
3¼” X 10” HORIZONTAL
MAXIMUM DUCT LENGTH
3¼” X 10” VERTICAL
MAXIMUM DUCT LENGTH
7” ROUND
MAXIMUM
DUCT LENGTH
ROOF OR
WALL CAP
WITH DAMPER
ELBOW(S)*
(90° AND/OR 45°)
91 ft. 79 ft. 92 ft. 1 0
82 ft. 71 ft. 78 ft. 1 1
73 ft. 62 ft. 62 ft. 1 2
* Standard elbows with 1” internal radius.
NOTE: 6" round ducting is possible but may reduce exhaust efficiency.
Contents
Before proceeding to the installation, check the contents of the box. If items are missing or
damaged, contact the manufacturer.
Make sure that the following items are included:
BCDA and NCDA Series NCSEK Series
(1) 3¼” X 10” DAMPER ASSEMBLY
(FIND INSIDE OF HOOD)
EZ1 C
OMPONENTS
RECTANGULAR DUCTING7” ROUND DUCTING
OR
= 3¼” x 10”
= 3¼” x 14”
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ po x 10 po
= 3¼ po x 14 po
CONDUCTO RECTANGULARCONDUCTO REDONDO
O
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
4¼”
(1) TEMPLATE FOR DUCTING
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
AB
C
(PRINTED BOTH SIDES)
(2) GREASE FILTERS
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
C
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
8”
conséquence.
To be translated in Spanish.
C
L
7½”
10½”
14½”
C
Appuyer ce bord au mur arrière
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
TITLE TO BE TRANSLATED IN SPANISH
Apoyar este borde contra la pared de atrásPlace this edge against back wall
7 PULG.
DE
(1) 3¼” X 10” DAMPER ASSEMBLY
(FIND INSIDE OF HOOD)
EZ1 C
OMPONENTS
RECTANGULAR DUCTING7” ROUND DUCTING
OR
= 3¼” x 10”
= 3¼” x 14”
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ po x 10 po
= 3¼ po x 14 po
CONDUCTO RECTANGULARCONDUCTO REDONDO
O
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
4¼”
(1) TEMPLATE FOR DUCTING
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
AB
C
(PRINTED BOTH SIDES)
(2) GREASE FILTERS
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
C
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
8”
conséquence.
To be translated in Spanish.
C
L
7½”
10½”
14½”
C
Appuyer ce bord au mur arrière
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
TITLE TO BE TRANSLATED IN SPANISH
DE
Apoyar este borde contra la pared de atrásPlace this edge against back wall
7 PULG.
(2) INSTALLATION BRACKETS*
FOR FRAMED CABINET
(2) INSTALLATION BRACKETS*
FOR FRAMELESS CABINET
* FIND EZ1 BRACKETS ATTACHED INSIDE OF HOOD
ARTS BAG** CONTAINING:
(1) P
(4) NO. 8-18 X 1/2”
M
ETAL SCREWS
(6) N
O. 8 X 5/8”
RD. HD.
W
OOD SCREWS
** FIND PAR T S BAG BEHIND THE DAMPER ASSEMBLY INSIDE OF HOOD
(6) NO. 8 X 1/2”
C
OUNTERSUNK
WOOD SCREWS
(2) INSTALLATION BRACKETS*
FOR FRAMED CABINET
(2) INSTALLATION BRACKETS*
FOR FRAMELESS CABINET
* FIND EZ1 BRACKETS ATTACHED INSIDE OF HOOD
ARTS BAG** CONTAINING:
(1) P
(4) NO. 8-18 X 1/2”
M
ETAL SCREWS
(6) N
O. 8 X 5/8”
RD. HD.
W
OOD SCREWS
** FIND PAR T S BAG BEHIND THE DAMPER ASSEMBLY INSIDE OF HOOD
(6) NO. 8 X 1/2”
C
OUNTERSUNK
WOOD SCREWS
INSTALLATION
INSTALLATION MANUAL
9
BCS3 and NCS3 Series BCSM Series
VERTICAL EXHAUST
(2) GREASE FILTERS
(2) GREASE FILTERS
(1) 3¼” X 10”
D
AMPER ASSEMBLY
(FIND INSIDE OF HOOD)
(1) P
ARTS BAG* CONTAINING:
(5) NO. 8 X 5/8”
RD. HD.
W
OOD SCREWS
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
C
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
8”
conséquence.
To be translated in Spanish.
C
C
14½”
Appuyer ce bord au mur arrière
(2) SHIELDED HALOGEN BULBS
(50W, GU10)
(FIND INSIDE OF HOOD)
(1) 3¼” X 10”
D
AMPER ASSEMBLY
(FIND INSIDE OF HOOD)
OMPONENTS
EZ1 C
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
RECTANGULAR DUCTING7” ROUND DUCTING
OR
= 3¼” x 10”
= 3¼” x 14”
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ po x 10 po
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
CONDUCTO RECTANGULARCONDUCTO REDONDO
O
= 3¼ pulg. x 10 pulg.
7 PULG.
DE
L
7½”
10½”
= 3¼ pulg. x 14 pulg.
4¼”
AB
Apoyar este borde contra la pared de atrásPlace this edge against back wall
(1) TEMPLATE FOR DUCTING
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
C
(PRINTED BOTH SIDES)
(2) INSTALLATION BRACKETS*
FOR FRAMED CABINET
(1) BULB SUCTION
* FIND PA RT S BAG
THE DAMPER ASSEMBLY
BEHIND
INSIDE
CUP TOOL
OF HOOD
(2) INSTALLATION BRACKETS*
FOR FRAMELESS CABINET
* FIND EZ1 BRACKETS ATTACHED INSIDE OF HOOD
(1) P
ARTS BAG** CONTAINING:
(1) BULB SUCTION
CUP TOOL
(6) NO. 8 X 5/8”
RD. HD.
W
OOD SCREWS
** FIND PAR T S BAG BEHIND THE DAMPER ASSEMBLY INSIDE OF HOOD
(4) NO. 8-18 X 1/2”
M
ETAL SCREWS
(6) NO. 8 X 1/2”
C
OUNTERSUNK
WOOD SCREWS
INSTALLATION MANUAL
10
INSTALLATION
Prepare the Hood
NOTE: Since this manual covers many range hood models, some details in the following
illustrations may sligthly differ from your unit.
1 ] If present, remove all protective polyfilm from the hood and/or parts.
2 ] Using the finger cup or tab, remove the grease filters from the hood by pushing down and
tilting filter out .
B
C
3 ] Remove the EZ1 brackets from inside the hood by cutting off the tie wrap (no EZ1 brackets
in BCS3 and NCS3 Series). Remove both screws holding damper assembly to hood.
Remove parts bag (captured behind the damper assembly). Remove damper assembly from
inside the hood and keep the screws for further use.
SCREWS
EZ1
BRACKETS
DAMPER
ASSEMBLY
4 ] Remove the wiring cover (shaded part on illustration below) by sliding it out from the hood
and set it aside.
INSTALLATION
INSTALLATION MANUAL
11
5 ] Remove 2 screws from top of hood (see illustration below). Keep the screws for further use.
2 SCREWS
6 ] Remove Electrical Power Cable Knockout from top (vertical wiring) or back (horizontal wiring)
of hood. Install an appropriate strain relief, 1/2” diameter (not included).
ELECTRICAL
POWER CABLE
KNOCKOUT
NON-DUCTED INSTALLATION ONLY
7 ] Remove 3 screws retaining the recirculation cover plate (shaded part in illustration below)
to the hood. Discard this plate with its screws.
RECIRCULATION
COVER PLATE
SCREWS
INSTALLATION MANUAL
12
INSTALLATION
DUCTED INSTALLATION ONLY
8 ] Remove 3¼” x 10” vertical, 3¼” x 10” horizontal, or 7-inch round knockout plate as
appropriate for your ducting method (see FIGURES 1 A and 1 B).
FIGURE 1 A
7” ROUND KNOCKOUT
PLATE (ALSO REMOVE
VERTICAL KNOCKOUT PLATE)
3¼” X 10”
VERTICAL
KNOCKOUT
PLATE
3¼” X 10”
HORIZONTAL
KNOCKOUT
PLATE
9 ] Attach 3¼” x 10” Damper Assembly on top OR back of hood (if using 3¼” x 10” duct; shaded
part in FIGURE 2 A below) or 7” Round Duct Plate (purchase separately) (if using 7-inch round
duct, FIGURE 3) over the knockout opening. When installed, the 3¼” x 10” damper assembly
must open as shown in FIGURE 2 B.
FIGURE 2 A FIGURE 2 B
3¼” X 10”
DAMPER
ASSEMBLY
SCREWS
FIGURE 1 B
TOP/BACK
EDGE OF
HOOD
DAMPER
FLAP
PIVOT
SCREWS
3¼” X 10”
DAMPER
ASSEMBLY
FIGURE 3
7” ROUND
SCREWS
BACK OF
HOOD
DAMPER
FLAP
PIVOT
DUCT
PLATE
NOTE: To accommodate off-center ductwork, the 7” round duct plate can be installed up
to 1/2” on either side of the hood center.
TIP: Insert a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting)
or 7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease
connection with the house ductwork.
INSTALLATION
INSTALLATION MANUAL
13
Prepare the Hood Location
VERTICAL EXHAUST
VERTICAL EXHAUST
NOTE: Before starting installation, read all the steps of these instructions.
Use the illustration below to identify your kitchen cabinet type.
FRAMED CABINET FRAMELESS CABINET
This manual covers 2 kinds of installation: the standard (without EZ1 brackets) and the EZ1
one-person installation system (using included template and brackets). For the standard
installation, go to page 19.
EZ1 One-person installation system
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as
the range hood width. If the cabinet is greater than 1/2” wider than the range hood width, please
use the standard installation method.
1 ] Use the proper template for vertical OR horizontal disharge (included) for placement of
ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a
duct access hole, only cut the hole for electrical wiring. If replacing a hood and plan to use
the existing duct and electrical, steps 2 to 5 may not be necessary. If so, skip to step 6.
2 ] Measure and mark the hood center line on cabinet bottom.
3 ] Align the center line on template with the hood center line marked on the bottom of the
cabinet, placing the edge (where indicated) of the template against back wall. When using
with framed cabinet for vertical exhaust installation, fold over rear edge of template equal
to the depth of the cabinet frame at the wall (use graduations on template, C locations on
template). Tape the template in place.
NOTE: When facing the installation, A and B (on template) must be at right.
VERTICAL EXHAUST
CABINET FRONT
CABINET FRONT
DUCTING
INSTALLATION MANUAL
INSTALLATION
14
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
C
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
8”
conséquence.
To be translated in Spanish.
C
C
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
RECTANGULAR DUCTING7” ROUND DUCTING
OR
= 3¼” x 10”
= 3¼” x 14”
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ po x 10 po
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
CONDUCTO RECTANGULARCONDUCTO REDONDO
O
= 3¼ pulg. x 10 pulg.
DE
C
14½”
Appuyer ce bord au mur arrière
L
7 PULG.
= 3¼ pulg. x 14 pulg.
4¼”
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
AB
C
7½”
10½”
Apoyar este borde contra la pared de atrásPlace this edge against back wall
FOLD TEMPLATE ALONG GRADUATED
SCALE
WHEN INSTALLING TO FRAMED
P
CABINET
.
CENTER LINE
Place this edge against
cabinet bottom.
Appuyer ce bord contre le bas
de l’armoire.
Apoyar este borde contra
la base del armario.
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
C
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
To be translated in Spanish.
C
CENTER LINE
HORIZONTAL EXHAUST
DUCTING
AB
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
CONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
ELECTRICAL
ACCESS HOLE
LOCATION (A)
C
L
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
RECTANGULAR DUCTING
= 3¼” x 10”
= 3¼” x 14”
TITLE TO BE TRANSLATED IN SPANISH
CONDUCTO RECTANGULAR
8”
IN WALL)
(
14½”
A
Electrical access hol
A = single blower ho
B = double blower
Centre du tr
d’alim
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
RECTANGULAR DUCTING7” ROUND DUCTING
OR
= 3¼” x 10”
= 3¼” x 14”
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ po x 10 po
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
CONDUCTO RECTANGULARCONDUCTO REDONDO
O
= 3¼ pulg. x 10 pulg.
DE
C
L
7 PULG.
= 3¼ pulg. x 14 pulg.
7½”
10½”
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
4¼”
A = single blower hood
B = double blower hood
AB
A
C
C
ELECTRICAL
ACCESS HOLE
LOCATION (A)
IN CABINET BOTTOM)
(
4 ] Drill a 1/8” dia. pilot hole for house wiring, at A location on template.
5 ] Use a sharp pencil or 1/8” drill bit to mark the locations for the appropriate duct access
holes (16 locations for 7” round duct, or 4 corner locations for rectangular duct). Remove the
template.
6 ] Draw the border for the exhaust ducting by linking its marks (16 for round duct and 4 for
rectangular duct), then cut the opening in the cabinet bottom (vertical exhaust) or in the wall
(horizontal exhaust). Drill the house wiring hole by using a 1½” hole saw centered with the
pilot hole previously made in 4.
7 ] Install the proper installation brackets according to the type of cabinet (framed or frameless).
See below.
FRAMED CABINET
Refer to the marking on the brackets to determine the correct installation side and
orientation.
XY
7/64”
Z
Mate the corresponding bracket to the cabinet side frame, while placing rear end
of bracket against the wall. Use a pencil to mark 3 holes (there are 6 holes but only
3 are necessary).
INSTALLATION
INSTALLATION MANUAL
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the side frame using a Phillips screwdriver and 3 provided
no. 8 x 5/8” wood screws. Repeat for the other side frame.
15
FRAMELESS CABINET
Refer to the marking on brackets to determine the correct installation side and orientation.
X
Y
3 X
Z
[ \
7/64”
Align the corresponding bracket to the cabinet side, while placing rear end of bracket
against the wall. Draw a line on the outer edge of the bracket (as shown).
Slide the bracket towards the center of cabinet and align the outside edge of the
bracket with the marked line, keeping the rear end edge leaning on the wall.
Use a pencil to mark 3 holes.
INSTALLATION MANUAL
16
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the cabinet bottom using a Phillips screwdriver and 3 provided
countersunk wood screws. Repeat for the other cabinet side.
INSTALLATION
Install the Hood (EZ1 Brackets)
OTE: N The following procedure applies to both framed or frameless cabinet installations.
1 ] Run house power cable between service panel and hood location.
2 ] There are 2 pairs of recessed holes on each side of the top of the hood (on rear: A and B,
on front C and D on illustration below); these holes allow the range hood to hang on the
brackets (previously installed).
A
C
D
B
HORIZONTAL EXHAUST INSTALLATION ONLY
3 ] Temporarily hang the hood on the brackets using its 2 recessed REAR HOLES (A and B).
While holding the hood, run the house power cable into the hood through the strain relief
previously installed in step 6 on page 12.
A
B
4 ] Unhook the rear holes from the brackets and hang the hood using its 2 recessed FRONT
HOLES (C and D). While holding the hood, attach the power cable to the hood using the
strain relief.
VERTICAL EXHAUST INSTALLATION AND NON-DUCTED INSTALLATION ONLY
5 ] Hang the hood on the brackets using the 2 recessed FRONT HOLES (C and D). While
holding the hood, run the house power cable into the hood through the strain relief
previously installed in step 6 on page 12. Attach power cable to the hood.
DUCTED INSTALLATION ONLY
6 ] Connect the ductwork to the hood and use metal foil duct tape to make joints secure and
air-tight. Make sure the damper assembly (or round duct plate) enters the ductwork and
that the damper opens and closes freely.
NOTE: See final installation steps on next page.
INSTALLATION
INSTALLATION MANUAL
17
7 ] For framed cabinet, secure the hood to the EZ1 brackets using 4 no. 8-18 x 1/2” metal screws
(included in parts bag). Insert 2 screws per side, in the slots (as shown in insets on illustration
below).
8 ] For frameless cabinet, secure the hood to the cabinet using 4 no. 8 x 5/8” round head wood
screws (included in parts bag). Insert 2 screws per side, in the slots (as shown in insets on
illustration below).
FRAMED CABINET FRAMELESS CABINET
METAL
SCREWS
WOOD
SCREWS
INSTALLATION MANUAL
18
INSTALLATION
Standard Installation (without EZ1 brackets)
VERTICAL DUCT
ACCESS HOLE
1015/16"
5¼"
5¼"
CENTER
LINE
HOOD MOUNTING SCREWS (4)
ELECTRICAL
ACCESS HOLE
(
IN CABINET BOTTOM)
WOOD SHIMS
(
RECESSED-BOTTOM
CABINETS
ONLY)
CABINET FRONT
3/4"
1Ǫ"
1½"
7³/16"
9Ǭ" (24" HOOD)
12Ǭ" (30"
HOOD)
47/16"
CABINET
BOTTOM
9Ǭ" (24"
HOOD)
12Ǭ" (30"
HOOD)
CABINET
BOTTOM
CABINET FRONT
HORIZONTAL DUCT
ACCESS HOLE
HOOD
MOUNTING
SCREWS (4)
ELECTRICAL
ACCESS HOLE
(
IN WALL)
3Ǭ"
CENTER
LINE
WOOD SHIMS
(
RECESSED-BOTTOM CABINETS ONLY)
13/16"
3/16"
5¼"
5¼"
9Ǭ" (24" HOOD)
12Ǭ" (30"
HOOD)
9Ǭ" (24"
HOOD)
12Ǭ" (30"
HOOD)
7³/
16"
1 ] Use the proper diagram below for placement of ductwork and electrical cutout in cabinet
or wall. For a non-ducted installation, DO NOT cut a duct access hole, only cut the hole for
electrical wiring.
3¼" X 10"
VERTICAL DUCTING
3¼" X 10"
HORIZONTAL DUCTING
2 ] Install half-way four (4) ROUND HEAD no. 8 x 5/8” mounting screws into shims/cabinet,
according to the proper diagram above. (Mounting screws are included in parts bag, but wood
shims and shim mounting screws are not included).
HOOD MOUNTING SCREWS (4)
9Ǭ" (24"
12Ǭ" (30"
HOOD)
HOOD)
7-IN. ROUND
7-IN. ROUND
4¹¹/16"
WOOD SHIMS
RECESSED-BOTTOM
(
CABINETS
ONLY)
DUCT
DUCT
ACCESS
ACCESS
HOLE
HOLE
9Ǭ" (24"
12Ǭ" (30"
7³/
16"
8" DIA.
HOLE
ACCESS HOLE
IN CABINET BOTTOM)
(
7-IN. ROUND
VERTICAL DUCTING
HOOD)
HOOD)
1Ǫ"
ELECTRICAL
1½"
10
INSTALLATION
15
/16"
INSTALLATION MANUAL
19
Install the Hood (Standard Installation)
1 ] Run house power cable between service panel and hood location. Run the house power
cable into the hood through the strain relief previously installed in step 6 on page 12.
2 ] Hang hood from (4) mounting screws previously installed. Slide hood back towards wall until
mounting screw heads are engaged in narrow end of keyhole slots in top of hood. Tighten
screws securely. Attach power cable to the hood using the strain relief.
DUCTED INSTALLATION ONLY
3 ] Connect ductwork to hood and use metal foil duct tape to make joints secure and air-tight.
Make sure the damper assembly (or round duct plate) enters the ductwork and that the
damper opens and closes freely.
INSTALLATION MANUAL
20
INSTALLATION
Connect the Wiring
!
WARNING
Risk of electric shock. Electrical wiring must be done by qualifi ed
personnel in accordance with all applicable codes and standards.
Before connecting wires, switch power off at service panel and lock
service disconnecting means to prevent power from being switched
on accidentally.
MOTOR
GROUND
WIRE
GROUND
SCREW
HOUSE
POWER CABLE
1 ] Connect House Power Cable to range hood wiring: BLACK to BLACK, WHITE to WHITE and
GREEN or bare wire under GREEN ground screw.
TABS ON INNER
TOP OF HOOD
SCREW
2 ] Reinstall wiring cover and attach it to the hood using its retaining screw.
!
CAUTION
Ensure both tabs on inner top of hood are engaged in their corresponding slots in
wiring cover. Also, take care not to pinch wires while reinstalling wiring cover.
ENGAGED IN
WIRING COVER
SLOTS.
INSTALLATION
INSTALLATION MANUAL
21
Light Bulbs (BCS3, BCSM and NCS3 Series only)
The BCS3, BCSM and NCS3 Series range hoods require two shielded Halogen Bulbs (120 V,
50 W max., MR16 or PAR16 with GU10 base) (included only with BCSM Series range hoods).
!
WARNING
Do not touch lamps during or soon after operation. Burns may occur. In order to prevent
the risk of personal injury, only install shielded halogen lamps. Also, never install a cool
beam, a dichroic lamp, a lamp not suitable for use in recessed luminaires or identified for
use in enclosed fixtures.
BULB LEADS
1 ] Align the bulb leads with the small indentations located on the border of the lamp location on
hood (see inset above), then install the bulbs by placing the bulb leads into their grooves in
the socket.
2 ] Gently push upwards and turn clockwise until secure.
NOTE: The Suction Cup Tool (included with hood) can be used to install and remove light bulbs.
Press suction cup tool on bulb and rotate counterclockwise to remove bulb or clockwise to
install bulb.
Most GU10 LED replacement bulbs commonly found in the market are not designed
for use in a cooking environment and might not perform as advertised. Their usage
with this product is not recommended.
BULB LEAD
GROOVES
(IN SOCKET)
!
CAUTION
SUCTION
CUP TOOL
INSTALLATION MANUAL
22
Install the Filters
Ducted Installation Only:
Re-install grease filters removed in step 2 on page 11, under “Prepare the Hood”.
Non-ducted Installation Only:
Purchase two non-ducted filters from your local distributor or retailer (see product specification label
for filter type). Attach the non-ducted filters following instructions packed with the non-ducted filters.
INSTALLATION
NCSEK SERIES
GREEN/YELLOW
ORANGE
RED
WHITE
G/YOR
W
LED
LED
W
BK
R
2
1
R
LED
driver
WBK
BK
2
1
FAN MOTOR
BN
BN/W
R
6
W
O
G/Y
BK
12345
COLOR CODE
BLACK
BLUE
BROWN
BROWN/WHITE
BKBLBN
BN/W
Light Switch
BL
W
W
BK (High)
R (Low)
G/Y
WIRING DIAGRAM
Motor Switch
BK
BK
INSTALLATION MANUAL
Line
Neutral
Ground
120 V AC
23
BCDA AND NCDA SERIES
GREEN/YELLOW
ORANGE
RED
WHITE
G/YOR
W
COLOR CODE
LED
BN
R
O
FAN MOTOR
6
LED
W
R (Low)
O (Medium)
W
G/Y
BK
12345
W
BK (High)
BN/W
BLACK
BLUE
BROWN
BROWN/WHITE
BKBLBN
BN/W
J6
Override
12 34 5 6
INSTALLATION MANUAL
WIRING DIAGRAM
BK
123
LED
J4
R
R
R
BL
BK
BL
4
3
4
1
2
567
8
Interface
J10
54321
J1
Transformer
6
7
54321
J2
Power, Motor
W
G/Y
BK
BK
W
Control Board
control board.
to J10 on back of
User interface mounted
Line
Neutral
Ground
120 V AC
24
BCSM SERIES
RED
WHITE
YELLOW
Lights
High/Low12 3
Lights
On/Off
RWY
BROWN/WHITE
GREEN/YELLOW
ORANGE
COLOR CODE
BN/W
G/Y
O
BLACK
BLUE
BROWN
BKBLBN
Motor Speeds
Motor
On/Off
BN
BK
123 4 56
Y (Low)
BL (High)
BK
BK
W
W
FAN MOTOR
O
R
6
R (Low)
O (Medium)
W
G/Y
BK
12345
W
BK (High)
W
BN/W
G/Y
WIRING DIAGRAM
Line
Neutral
Ground
INSTALLATION MANUAL
120 V AC
25
BCS3 AND NCS3 SERIES
RED
WHITE
YELLOW
RWY
BROWN/WHITE
GREEN/YELLOW
ORANGE
COLOR CODE
BN/W
G/Y
O
Y (Low)
BK
BL (High)
BN
R
O
FAN MOTOR
6
BK
W
W
R (Low)
W
G/Y
BK
12345
W
W
BK (High)
BN/W
INSTALLATION MANUAL
26
BLACK
BLUE
BROWN
BKBLBN
WIRING DIAGRAM
Light Switch
G/Y
1
2
BK
BK
Motor Switch
1
2
Line
Neutral
Ground
120 V AC
NCSEK SERIES
KEY NO.PART NO.DESCRIPTION
S97020029 RECIRCULATION COVER PLATE, BLACK (INCLUDING SCREWS) 1
1
S97020030 RECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)1
S97020031 RECIRCULATION COVER PLATE, STAINLESS STEEL (INCL. SCREWS)1
2 S97020534 3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)111
3 S97020408 B
4 S97020407 FANPELLER (INCLUDING ITEM 5) 1 1 1
5 SR99420635 CLIP FOR FANPELLER 111
6 S99010431-002 GREASE FILTER - OPEN MESH - TYPE C1 (SET OF 2) 1 1 1
S99030377 ROCKER SWITCHES, WHITE (SET OF 2) 1
7
S99030376 ROCKER SWITCHES, BLACK (SET OF 2) 1
S99030375 R
8 S97020444 LED MODULE (PAIR)111
* S97020446 DRIVER FOR LED ENERGY STAR (WITH SCREWS)111
* S97020449 H
* S98011637 W
* S97020360
* S97020466
* S99527587 NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS)111
* S97020470 EASY INSTALL KIT (INCLUDING HARDWARE)111
* ITEM NOT SHOWN.
LOWER MOTOR (INCLUDING 4 SCREWS AND 1 CAPACITO R)111
OCKER SWITCHES, GREY (SET OF 2) 1
ARNESS FOR ROCKER SWITCH CONTROL WITH LEDS 111
IRING COVER 111
PARTS BAG INCLUDING: 4 METAL SCREWS NO. 8-18 X 1/2”,
6 ROUND HEAD NO. 8 X 5/8” WOOD SCREWS,
6 NO. 8 X 1/2” COUNTERSUNK WOOD SCREWS
N
ON-DUCTED FILTERS - TYPE XC (SET OF 2)
(NON-DUCTED INSTALLATION ONLY)
QUANTITY
30"
WHITE
111
111
30"
STAINLESS
30"
BLACK
SERVICE PARTS
INSTALLATION MANUAL
REPLACEMENT PARTS AND REPAIRS
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts
only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with
all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause
serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC
recommends to contact a certified service depot for all replacement parts and repairs.
27
BCDA AND NCDA SERIES
INSTALLATION MANUAL
SERVICE PARTS
KEY
NO.
* ITEM NOT SHOWN.
REPLACEMENT PARTS AND REPAIRS
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts
only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with
all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause
serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC
recommends to contact a certified service depot for all replacement parts and repairs.
P
ART NO.DESCRIPTION
S97020030 RECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)1
1
S97020031 RECIRCULATION COVER PLATE, STAINLESS STEEL (INCLUDING SCREWS)1
S97020029 RECIRCULATION COVER PLATE, BLACK (INCLUDING SCREWS)1
2 S97020534 3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)111
3 S97020408 BLOWER MOTOR (INCLUDING 4 SCREWS AND 1 CAPACITO R)111
4 S97020407 F
5 SR99420635 CLIP FOR FANPELLER 111
6 S99010434-002 GREASE FILTER - MICRO MESH - TYPE C2 (SET OF 2) 1 1 1
7 S97020444 LED MODULE (PAIR)111
8 S97020445 TRANSFORMER 24 V 18 VA (WITH SCREWS)111
S97020431 CAPTOUCH CONTROL LED, STAINLESS (WITH SCREWS)1
9
S97020432 C
S97020433 CAPTOUCH CONTROL LED, BLACK (WITH SCREWS)1
* S97020452 WIRE HARNESS 111
* S98011637 WIRING COVER 111
* S97020360
* S97020466
* S99527587 NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS)111
* S97020470 EASY INSTALL KIT (INCLUDING HARDWARE)111
ANPELLER (INCLUDING ITEM 5) 1 1 1
APTOUCH CONTROL LED, WHITE (WITH SCREWS)1
PARTS BAG INCLUDING: 4 METAL SCREWS NO. 8-18 X 1/2”,
6 ROUND HEAD NO. 8 X 5/8” WOOD SCREWS,
6 NO. 8 X 1/2” COUNTERSUNK SCREWS
N
ON-DUCTED FILTER - TYPE XC (SET OF 2)
(NON-DUCTED INSTALLATION ONLY)
STAINLESS
QUANTITY
30"
111
111
30"
WHITE
30"
BLACK
28
BCS3 SERIES
KEY
NO.
* ITEM NOT SHOWN.
P
ART NO.DESCRIPTION
S97020030 RECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)11
1
S97020031 RECIRCULATION COVER PLATE, STAINLESS STEEL ( INCL. SCREWS)1 1
S97020029 RECIRCULATION COVER PLATE, BLACK (INCLUDING SCREWS)1
2 S97020534 3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS) 11111
3 S97020408 BLOWER MOTOR (INCLUDING 4 SCREWS AND 1 CAPACITOR ) 11111
4 S97020407 F
5 SR99420635 CLIP FOR FANPELLER 11111
S99010434-001 GREASE FILTER - MICRO MESH - TYPE B2 (SET OF 2) 1 1
6
S99010434-002 GREASE FILTER - MICRO MESH - TYPE C2 (SET OF 2) 1 1 1
S99030367 ROCKER SWITCH, GREY (SET OF 2) 1 1
7
S99030355 ROCKER SWITCH, WHITE (SET OF 2) 1 1
S99030356 R
8 S97020448 WIRE HARNESS 11111
* S98011637 WIRING COVER 11111
* S97018623
* S97020465
* S97020466
* S99527587 NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS) 11111
* SV05921 SHIELDED HALOGEN BULB 50 W, GU10 22222
ANPELLER (INCLUDING ITEM 6) 11111
OCKER SWITCH, BLACK (SET OF 2) 1
PARTS BAG INCLUDING: 1 SUCTION CUP TOOL, 5 ROUND HEAD
NO. 8 X 5/8” WOOD SCREWS,
ON-DUCTED FILTER - TYPE XB (SET OF 2)
N
(NON-DUCTED INSTALLATION ONLY
N
ON-DUCTED FILTER - TYPE XC (SET OF 2)
(NON-DUCTED INSTALLATION ONLY)
24"
STAINLESS
11111
11
24"
WHITE
QUANTITY
30"
STAINLESS
30"
WHITE
111
30"
BLACK
SERVICE PARTS
INSTALLATION MANUAL
REPLACEMENT PARTS AND REPAIRS
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts
only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with
all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause
serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC
recommends to contact a certified service depot for all replacement parts and repairs.
29
NCS3 SERIES
KEY
NO.
* ITEM NOT SHOWN.
PART NO.DESCRIPTION
S97020030 RECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)1
1
S97020031 RECIRCULATION COVER PLATE, STAINLESS STEEL (INCLUDING SCREWS)1
S97020029 RECIRCULATION COVER PLATE, BLACK (INCLUDING SCREWS)1
2 S97020534 3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)111
3 S97020408 B
4 S97020407 FANPELLER (INCLUDING ITEM 6) 1 1 1
5 SR99420635 CLIP FOR FANPELLER 111
6 S99010434-002 GREASE FILTER - MICRO MESH - TYPE C2 (SET OF 2) 1 1 1
S99030367 ROCKER SWITCH, GREY (SET OF 2) 1
7
S99030355 ROCKER SWITCH, WHITE (SET OF 2) 1
S99030356 R
8 S97020448 WIRE HARNESS 111
* S98011637 WIRING COVER 111
* S97018623
* S97020466
* S99527587 NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS)111
* SV05921 S
LOWER MOTOR (INCLUDING 4 SCREWS AND 1 CAPACITO R)111
OCKER SWITCH, BLACK (SET OF 2) 1
PARTS BAG INCLUDING: 5 ROUND HEAD NO. 8 X 5/8” WOOD SCREWS,
1 SUCTION CUP TOOL
N
ON-DUCTED FILTER - TYPE XC (SET OF 2)
(NON-DUCTED INSTALLATION ONLY)
HIELDED HALOGEN BULB 50 W, GU10 2 2 2
QUANTITY
30"
STAINLESS
30"
WHITE
BLACK
111
111
30"
INSTALLATION MANUAL
30
SERVICE PARTS
R
EPLACEMENT PARTS AND REPAIRS
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts
only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with
all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause
serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC
recommends to contact a certified service depot for all replacement parts and repairs.
BCSM SERIES
KEY
NO.
* ITEM NOT SHOWN.
P
ART NO.DESCRIPTION
S97020030 R
1
S97020031 RECIRCULATION COVER PLATE, STAINLESS STEEL (INCLUDING SCREWS)1
2 S97020534 3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)11
3 S97020409 BLOWER MOTOR (INCLUDING 4 SCREWS AND 1 CA PACITOR )11
4 S97020407 FANPELLER (INCLUDING ITEM 6) 1 1
5 SR99420635 C
6 S99010434-002 GREASE FILTER - MICRO MESH - TYPE C2 (SET OF 2) 1 1
7 S97020427 MECHANICAL PUSH-BUTTON CONTROL (6 BUTTONS)11
8 S97020450 WIRE HARNESS 11
* S98011637 WIRING COVER 11
* S97020292
* S97020466
* S99527587 NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS)11
* SV05921 SHIELDED HALOGEN BULB 50 W, GU10 2 2
* S97020470 EASY INSTALL KIT (INCLUDING HARDWARE)11
ECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)1
LIP FOR FANPELLER 11
PARTS BAG INCLUDING: 4 METAL SCREWS NO. 8-18 X 1/2”,
6 ROUND HEAD NO. 8 X 5/8” WOOD SCREWS,
6 NO. 8 X 1/2” COUNTERSUNK SCREWS
N
ON-DUCTED FILTER - TYPE XC (SET OF 2)
(NON-DUCTED INSTALLATION ONLY)
QUANTITY
30"
STAINLESS
30"
WHITE
11
11
SERVICE PARTS
INSTALLATION MANUAL
EPLACEMENT PARTS AND REPAIRS
R
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts
only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with
all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause
serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC
recommends to contact a certified service depot for all replacement parts and repairs.
31
INSTALLATION MANUAL
32
Warranty Period and Exclusions: Venmar Ventilation ULC (the “Company”) warrants to the original consumer purchaser
of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for
a period of one (1) year from the date of original purchase
Range Hood Product that includes built-in LED modules, the Company warrants the LED modules and driver to be free from
material defects for a period of three (3) years from the date of purchase.
The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced
under this limited warranty shall be the remainder of the original warranty period (or such longer period as may be required
by applicable law).
This warranty does not cover fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof
caps, wall caps and other accessories for ducting that may be purchased separately and installed with the Product. This
warranty also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or parts
which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance,
storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary
to recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage
caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or
nonresidential use, or (j) damage caused by fire, flood or other act of God or (k) Products with altered, defaced or removed
serial numbers. This warranty covers only Products sold to original consumers in Canada by the Company or its Canadian
distributors authorized by the Company.
This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective
products. The foregoing warranties are exclusive and in lieu of any other warranties and conditions, express or implied. THE
COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS
AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law
prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is
limited to the period specified for the express warranty above. Some jurisdictions do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is for the
sole purpose of identifying it and shall not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid
under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only to the
extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining provisions
of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or
repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in
breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or
replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or
other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to
the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible
for damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured
Products or parts in the warranty repair or replacement process. Such Products and parts will be comparable in function
and performance to an original Product or part and warranted for the remainder of the original warranty period (or such
longer period as may be required by applicable law).
Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or
replacement. If the Product or component is no longer available, replacement may be made with a similar product of equal
or greater value, at Company’s sole discretion. This is your sole and exclusive remedy for breach of this limited warranty.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR,
REPLACE OR REFUND, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER
THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL
NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN
CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages include but are not limited to
such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing
or replacing other property which was damaged if the Product does not work properly.
THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER
OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING
OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT
LIABILITY, WITH RESPECT TO THE PRODUCT OR THE COMPANY’S ACTS OR OMISSIONS OR OTHERWISE.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from jurisdiction to jurisdiction. The disclaimers, exclusions, and limitations of liability under this warranty will not apply
to the extent prohibited by applicable law.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and
does not include the cost of field service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty
will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product,
except for those incurred with the Company’s prior written permission.
WARRANTY
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or
telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and
part identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty
service, you must present evidence of the original purchase date. If you cannot provide a copy of the original written limited
warranty, then the terms of the Company’s most current written limited warranty for your particular product will control.
The most current limited written warranties for the Company’s products can be found at www.broan.ca or www.nutone.ca.
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Québec, Canada J2C 7W9
www.broan.ca www.nutone.ca 1-877-896-1119
Limited Warranty
(or such longer period as may be required by applicable law). For
Loading...