Broan AER110LBN Installation Manual

ROOMSIDE SERIES

Decorative Fan-Light Ventilateur luminaire décoratif Ventilador con luz decorativo

Model number:

Numéro de modèle :

Número de modelo:

USE & CARE INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION,

D’UTILISATION ET D’ENTRETIEN

INSTRUCCIONES DE INSTALACIÓN,

AER110LBN

INSTALLATION AND

USO Y CUIDADO

Broan Hartford, Wisconsin www.broan.com 800-558-1711 Venmar Ventilation ULC Drummondville (Quebec), Canada www.broan.ca 877-896-1119

English - See page 2

Français - Voir page 7

Español - Consulte la página 12

order Service Parts: go to the appropriate website and type the model number in the “Model Search” field.

Installer: Leave this manual with the homeowner.

READ AND SAVE THESE INSTRUCTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons, observe the following:

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

• Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

• Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

• Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• This unit must be grounded.

CAUTION

• For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

• For installation in flat ceilings only.

• To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

• Please read specification label on product for further information and requirements.

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive appearance - remove grille and vacuum interior of unit with the dusting brush attachment.

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the blower assembly (includes motor and impeller).

OPERATION

Use an on/off switch or speed control to operate this ventilator. See “Wiring Diagram” for details.

INSTALLATION AND USE & CARE INSTRUCTIONS

SAFETY

ALL INSTALLATIONS

Start here.

COOKING AREA

Do not install above or

inside this area.

2. Remove wiring panel from fan housing (if already installed).

NOT FOR USE IN

A COOKING AREA.

Cooking

Equipment

Floor

IMPORTANT - The ducting from this fan to the outside

of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow.

ROOF CAP * (with built-in damper)

INSULATION

(Place around and

over fan housing.)

FAN

HOUSING

POWER

CABLE

Keep duct

runs short.

Seal gaps

around

housing.

4-IN. ROUND

DUCT

Purchase separately.

OPTION -

Seal duct joints

with tape.

To mount housing anywhere between ceiling framing:

4-IN. ROUND

ELBOWS

WALL CAP

(with built-in

damper)

Use optional Hanger Bar Kit (sold separately from local distributors or website). Follow mounting instructions included with kit.

3. A pair of flanges may be attached to housing if desired or required.

Snap both flange pieces under rolled-over edge of housing (all four sides).

4. Attach grille brackets to housing.

INSTALLATION AND USE & CARE INSTRUCTIONS

INSTALLATION

1. Remove blower and all packing material from fan housing.

NEW CONSTRUCTION

For Retrofit Installation - Skip to Page 5.

5. Attach damper/duct connector to fan housing.

Push connector through opening from inside of housing. Engage tabs and secure with screw from parts bag.

TABS

7. Connect 4-in. round duct.

8. Connect wiring.

Connect power cable to housing with appropriate UL approved connector. Make wiring connections as shown in “Wiring Diagram” section. Re-install wiring panel and secure with screw from parts bag.

6. Mount housing to ceiling structure.

Make sure bottom of housing will be flush with finished ceiling.

For proper location using ½” ceiling material: Bend out housing tabs to fit against bottom of structure.

Secure housing through mounting ears with appropriate fasteners.

If mounting housing to I-joist, use wood blocking as shown.

I-JOIST

WOOD BLOCKING

INSTALLATION AND USE & CARE INSTRUCTIONS

HOUSING TABS

INSTALLATION

9. Install blower.

Re-install blower. Secure blower with (2) screws from parts bag and plug blower into black receptacle.

10. Finish ceiling, then install grille.

Attach MOUNTING PLATE to housing with (2) SCREWS. Connect LIGHT PANEL PLUG to receptacle in corner of

housing.

Line up (3) STUDS on GRILLE FRAME with (3) KEYHOLE SLOTS on MOUNTING PLATE. Rotate GRILLE FRAME to secure in place.

RETROFIT

5. Remove old fan.

Enlarge ceiling opening (if necessary) to 9¾” (parallel to joist) by 10½” (perpendicular to joist). Leave ductwork and wiring in place.

10½-in.

9¾-in.

JOIST

KEYHOLE SLOT (3)

LIGHT PANEL

PLUG

GRILLE FRAME

MOUNTING PLATE

MOUNTING PLATE ATTACHMENT SCREW (2)

STUD (3)

INSTALLATION AND USE & CARE INSTRUCTIONS

6. Fold mounting ears flat against housing.

INSTALLATION

+ 11 hidden pages