Breville BEM800BS, BEM800CB, BEM800EL Operating Instructions

Breville Customer Service Center
Australian Customers Mail: PO Box 22
Phone: 1300 139 798 Fax: (02) 9384 9601 Email:
Customer Service:
askus@breville.com.au
www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
Copyright Breville Pty. Ltd. 2010.
New Zealand Customers Mail: Private Bag 94411
Greenmount, Auckland NEW ZEALAND
Phone:
0800 273 845
Fax: 0800 288 513 Email:
Customer Service:
askus@breville.com.au
Model BEM800 Issue - C10
CONGRATULATIONS
On the purchase of your new
Breville Fast Slow Cooker™
the Scraper Mixer Pro
Instruction Booklet
Suits all BEM800 models
CONGRATULATIONS
on the purchase of your new
Breville Scraper Mixer Pro
CONTENTS
4 Breville recommends safety first
7 Know your Breville
Scraper Mixer Pro
10 Assembly & operation
18 Care, cleaning and storage
20 Measuring and weighing
24 Hints and tips
28 The vital ingredients
36 Troubleshooting
38 Recipes
3
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE
Carefully read all instructions before
operating the Professional Scraper Mixer for the first time and save for future reference.
Remove and safely discard any
packaging material and promotional labels before using the bench mixer for the first time.
To eliminate a choking hazard for young
children, remove and safely discard the protective cover fitted to the power plug of this appliance.
Do not place the bench mixer near
the edge of a bench or table during operation. Ensure the surface is level, clean and free of water and other substances. Vibration during operation may cause the appliance to move.
Do not use the bench mixer on a sink
drain board.
Do not place the bench mixer on or near
a hot gas or electric burner, or where it could touch a heated oven.
Always ensure the bench mixer is
completely assembled before operating. Follow the instructions provided in this book.
Ensure the Speed Control Dial is in the
‘Off’ position and the bench mixer is switched off at the power outlet and the power cord is unplugged before attaching the beater, whisk or dough hook.
Do not use attachments other than those
provided with the bench mixer. Use only the beater whisk and dough hook
supplied with the mixer.
Do not operate the appliance
continuously on heavy loads for more than 3 minutes. None of the recipes in this book are considered a heavy load.
Handle the bench mixer and
attachments with care. Never place your fingers inside the mixing bowl or near the beater, whisk or dough hook during operation.
Keep hands, hair, clothing, as well as,
spatulas and other utensils away from moving beater, whisk or dough hook/ during operation.
Should an object such as a spoon or
spatula fall into the bowl while mixing, immediately ensure the Speed Control Dial is in the ‘Off’ position, turn the bench mixer off, unplug at the power outlet and remove the object.
Do not place hands in the mixing
bowl unless the bench mixer is disconnected from the power outlet. Ensure the Speed Control Dial is in the ‘Off ’ position, the bench mixer is switched off and unplugged from the power outlet before removing the beater, whisk or dough hook.
Ensure the motor and beater, whisk or
dough hook have completely stopped before disassembling.
Always remove the beater, whisk or
dough hook from the bench mixer before cleaning.
Care should be taken when removing the
food from the mixer bowl by ensuring the motor and the beater, whisk, or dough hook have completely stopped before disassembling. Ensure the Speed
4
BREVILLE RECOMMENDS SAFETY FIRST
Control Dial is in the ‘Off” position, the appliance is switched off at the power outlet and unplugged before unlocking the mixer motor head and moving into the upright position. The beater, whisk or dough hook should be released from the mixer motor head before removing the processed food from the mixer bowl and the beater, whisk or dough hook.
Ensure the mixer motor head is locked
into the horizontal (closed) position when not in use and before storing.
Always ensure the Speed Control Dial
is in the ‘Off’ position, the power is switched off at the power outlet and the power cord is unplugged from the power outlet before attempting to move the bench mixer, before assembling or disassembling, when not in use and before cleaning or storing.
Do not move the bench mixer whilst
in operation.
Do not leave the bench mixer
unattended when in use.
Do not place any part of the bench
mixer in the dishwasher other than the bowl, splash guard, beater, dough hook and whisk.
Do not place any part of the bench mixer
in the microwave oven.
Keep the bench mixer clean. Follow
the cleaning instructions provided in this book.
5
5
BREVILLE RECOMMENDS SAFETY FIRST
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
Fully unwind the power cord before use.
Do not let the power cord hang over
the edge of a bench or table, touch hot surfaces or become knotted.
To protect against electric shock do not
immerse the power cord, power plug or appliance in water or any other liquid.
The appliance is not intended for use
by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
It is recommended to regularly inspect
the appliance. To avoid a hazard do not use the appliance if power cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorised Breville Service Centre for examination and/or repair.
Any maintenance other than cleaning
should be performed at an authorised Breville Service Centre.
This appliance is for household use only.
Do not use this appliance for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.
The installation of a residual current
device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.
WARNING
Ensure the speed dial control is in the ‘off’ position the bench mixer is switched off at the power outlet and unplugged from the power outlet before attaching the beater, whisk or dough hook.
SAVE THESE INSTRUCTIONS
6
KNOW
your Breville Scraper Mixer Pro
KNOW YOUR BREVILLE SCRAPER MIXER PRO
A
D
C
G
K
H
F
J
A. Motor head Powerful motor for
thorough mixing results
B. 4.7L stainless steel mixing bowl
with handle
C. Illuminated LED speed indicator band
displays selected mixing task
D. Tilt back and lock down hinge button
the motor head tilts back and locks into position to allow easy removal of the mixing bowl and attachments
E. Bowl locking recess the bowl locking
recess allows the bowl to be securely locked into place for safety and stability when the mixer is in operation
F. LCD screen with count up & down
timer mixer can be set to count down
8
B
E
according to a specified time on a recipe or set to count up to asses mixing time
G. Pause function rotate dial to “pause”
to temporarily stop mixing and pause the timer
H. Breville Assist™ handles handles on
base and on motor head allow for easy and comfortable lifting of the mixer
I. Load Sensing Technology internal
sensors detect when heavy batters are being mixed and automatically adjust to maintain the selected speed (not shown)
J. Internal Cord Storage located in the rear
of the mixer. Cord pushes into the mixer base for convenient and tidy storage
KNOW YOUR BREVILLE SCRAPER MIXER PRO
L
N
K. Splash guard prevents ingredients from
splattering out of the bowl
L. Flat beater thoroughly mixes a variety
of mixtures such as cake and biscuit batter, pastries, and mashed potatoes
M. Wire whisk consistently mixes
and aerates for egg whites, cream and thin batters
N. Dough hook effectively kneads heavy
dough for bread and pizza
O. Scraper beater Scrapes the sides and
bottom of the bowl for exceptionally thorough mixing, of cake and biscuit batter, pastry and frosting.
P. Spatula (not shown)
M
O
ABOUT YOUR SCRAPER BEATER
The Breville Scraper Beater folds ingredients and continuously scrapes down the sides and bottom of the bowl for exceptionally thorough mixing. It virtually eliminates the need to scrape the bowl by hand with a spatula and cuts mixing time up to 60%.
Under-mixed batters produce poorly baked results, resulting in collapsing, unevenness of crumb, holes, low rising, streaking and course textures. the Scraper Beater will help to ensure a thoroughly mixed batter for your favourite cakes, biscuits, frosting and more.
9
ASSEMBLY & OPERATION
of your Breville Scraper Mixer Pro
ASSEMBLY & OPERATION
ASSEMBLING THE MIXER
Before using your Breville Scraper Mixer Pro for the first time, remove any packaging material and promotional labels. Ensure the speed control dial is in the ‘Off’ position, the mixer is switched off at the power outlet and the power cord is unplugged.
Remove the mixing bowl, beater, whisk and dough hook and wash in warm soapy water with a soft cloth. Rinse and dry thoroughly. The bowl and the attachments may be washed in the dishwasher.
NOTE
When first using your Breville Scraper Mixer Pro, you may notice an odour coming from the motor. This is normal and will dissipate with use.
ATTACHING THE BOWL
1. Place the mixer base on a level, dry
surface such as a bench top. The mixer motor head should be in the horizontal (closed) position. Raise the mixer motor head by depressing the tilt back hinge button.
3. Insert the mixing bowl into the bowl
locking recess of the mixer stand and turn clockwise until the bowl locks securely into place.
2. Lift the mixer motor head up until it tilts
back and locks into the open position.
NOTE
To remove or insert the mixing bowl, the mixer motor head must be raised and locked into the open position.
11
ASSEMBLY & OPERATION
ATTACHING THE SCRAPER BEATER, FLAT BEATER, DOUGH HOOK OR WHISK TO THE MIXER MOTOR HEAD
1. Ensure the mixer motor head is in the
raised/open position. Align the groove in the top of the mixing attachment with the locking pin on the spindle extending down from the mixer motor head.
2. Push the attachment upwards and turn
clockwise until it locks securely onto the locking pin on the spindle (see Fig. 1).
Fig. 1
3. Lower the mixer motor head by
depressing the tilt back button and gently pushing the mixer motor head down until it locks into the horizontal (closed) position (see Fig. 2).
NOTE
When ingredients are in the mixing bowl, the scraper beater may make a slight noise as it scrapes the sides and bottom of the bowl. This is normal and should not cause concern.
Do not turn the mixer on with the scraper beater in place if the mixing bowl is empty. This will cause the scraper beater to make a loud noise as it scrapes the bowl.
OPERATING THE MIXER
Planetary Mixing Action
By replicating a similar mixing action used by commercial mixers in bakeries and patisseries, The Breville Scraper Mixer Pro head rotates around the bowl whilst rotating the beater in the opposite direction. This ensures a superior and thorough mixing result without the need for a rotating bowl.
Fig. 2
4. The splash guard can now be assembled
if required. Slide the main ring into position on top of bowl, then assemble the pour spout.
12
1. Ensure the speed control dial is set to
the ‘Off’ position, plug the cord into a 220-240v power outlet and switch the power ‘ON’ at the power outlet. The illuminated LED speed indicator band will flash and the Count Up/Down timer will display “0:00.” The mixer is now ready to be used.
ASSEMBLY & OPERATION
NOTE
If the mixer has not been used for 3 minutes it will automatically change from 'Stand by mode' to a power saving 'OFF mode' and the illuminated LED will switch off. To exit 'OFF mode' and begin mixing, turn the dial to the selected speed or press one of the count up/down timer buttons.
2. Add ingredients to the mixing bowl as
indicated in the recipe.
Always begin mixing by selecting a low speed setting on the speed control dial. This will prevent ingredients splattering. Increase the speed as suited to the mixing task. The speed setting can be adjusted during operation by moving the dial clockwise for the main mixing settings. Use the mixing guide in this booklet as a reference.
THE COUNT-UP TIMER
The count-up timer is especially useful to gauge mixing time. You can monitor the time it takes to thoroughly mix the ingredients, so that the next time you mix the same ingredients you can set the count­down timer for the specific time.
The count-up timer will automatically begin counting up as soon as the dial is rotated from ‘Off’ to one of the speeds. When the dial is turned to "Pause" the total time will be displayed on the LCD and will flash. When the dial is turned to "OFF", the LCD display will reset back to "0:00".
If necessary, stop the mixer during operation and scrape any food mixture down the sides of the mixing bowl with a spatula.
NOTE
Always turn the Mixer off if you need to scrape the bowl during use, and then switch back on and continue mixing.
13
ASSEMBLY & OPERATION
THE COUNT-DOWN TIMER
The count-down timer is especially useful for any recipe that specifies the length of time ingredients should be mixed. For example, if a recipe reads, “beat for 3 minutes,” you can set the count-down timer to 3 minutes by pressing the up/down arrows. After 3 minutes of mixing, an alarm will sound and the motor will automatically turn off. The count-down timer will flash “OFF”. The control dial must to be rotated to the “Off” position to reset the timer and to continue mixing.
To set the count down timer, press the up or down arrows until the desired mixing time is displayed on the LCD screen.
NOTE
Press and hold the arrows down to scroll through the timer setting more quickly.
Rotate the dial clockwise to select the desired speed and to begin mixing. When the timer has finished counting down, “0:00” will flash on the LCD screen and a beep will sound to notify you that the time has expired. The mixer will automatically turn the motor off. The control dial must be rotated to the 'OFF' position to reset the timer and to continue mixing.
NOTE
The maximum time displayed on the timer is 59:59 (fifty nine minutes, fifty-nine seconds). The mixer will automatically switch Off at 59 minutes 59 seconds. The control dial needs to be rotated to the “Off” position to reset the timer and to continue mixing.
PAUSE MODE
While mixing, at any stage, you can rotate the control dial to the “pause” setting. This will turn the motor off and “pause” the timer. This enables you to assess the mixing progress or add additional ingredients without effecting the timer.
For example, if you are mixing using the ‘count-up timer’ mode, you can rotate the control dial from one of the mixing speeds to “pause”. The mixer motor will stop and the timer will “pause”. Once ready, you can rotate the dial back to one of the mixing speeds, the timer will continue to count­up from the exact time it was paused. Alternatively, if you have turned the mixer to “pause” you can then reset the timer to 0:00 by rotating the dial to “Off” position.
If using the “pause” function in ‘count­down timer’ mode, you can suspend the timer at any stage during the count-down process by rotating the control dial to the “pause” setting. To continue mixing in the ‘count-down timer’ mode, simply rotate the dial back into one of the mixing speeds or alternatively to the “Off” position to reset the timer to 0:00.
14
ASSEMBLY & OPERATION
MOTOR HEAD SAFETY CUT-OFF
The mixer is equipped with a motor head safety cut-off. If the motor head is lifted at any time while the mixer motor is switched on, the safety cut-off will automatically switch the mixer off.
To restart the mixer turn the speed control dial to the "Off" position and close the motor head to the normal position and re-select the desired speed from the dial.
To turn the mixer off, turn the dial to the “Off” position, switch the appliance off at
the power outlet and unplug the cord.
ELECTRONIC PROTECTION CUT-OFF – CURRENT OVERLOAD
The mixer is equipped with an electric protection cut-off and will automatically stop operating if the motor is stalled or overloaded. This is normally a result of excessive ingredients being processed at one time. Should the mixer go into this mode, the LED indicator band will flash and the error message “E1” will flash on the LCD screen and the buzzer will “beep” 3 times.
THERMO CUT-OFF – TEMPERATURE OVERLOAD
The mixer is equipped with a self-resetting safety device which safeguards against overheating the motor with excessive loads. If overheating occurs, the mixer will automatically activate the overheating protection device and the motor will switch itself off. Should the mixer go into this mode, the LED indicator band will flash and the error message “E2” will flash on the LCD screen and the buzzer will “beep” 3 times.
If this error occurs, turn the speed control dial to the ‘Off’ position, switch the appliance off at the power outlet and unplug the cord. Wait at least 15 minutes before restarting the mixer.
If this error occurs, turn the speed control dial to the ‘Off” position, switch the appliance off at the power outlet and unplug the cord. Remove some of the ingredients in the mixing bowl and then restart the mixer.
DISASSEMBLING THE MIXER
1. When mixing is complete, turn the
speed control dial to the ‘Off/Stand by’ position, switch the appliance off at the power outlet and unplug the cord.
2. Remove splash guard if assembled.
Separate pour spout then slide main ring out of position.
3. Raise the mixer motor head by
depressing the tilt back button and lift the mixer motor head up until it tilts back and locks into the open position.
15
ASSEMBLY & OPERATION
4. Remove the beater/dough hook/whisk
attachment by holding the mixer motor head and pressing the attachment upwards on the spindle. Turn the attachment anticlockwise to release it from the pin on the spindle.
5. Use a soft plastic spatula to remove
mixture from the beater, dough hook or whisk attachment.
NOTE
When lowering or lifting the mixer, always support the motor head with your other hand to prevent from free-falling.
6. Remove the mixing bowl from the
indented bowl locking recess of the mixer Base and turn anti-clockwise until the bowl releases. Use a soft plastic spatula to remove mixture from the mixing bowl.
7. Lower the mixer motor head by
depressing the tilt back hinge button and pushing the mixer motor head down until it locks into the horizontal (closed) position.
WARNING
Avoid contact with beater/dough hook/ whisk during operation. Keep hands, hair, clothing, spatulas and other utensils away from beater/dough hook/ whisk to prevent personal injury or damage to the mixer.
16
17
CARE, CLEANING
& STORAGE
of your Breville Scraper Mixer Pro
CARE, CLEANING & STORAGE
CLEANING AFTER USE
1. Always ensure the speed control dial
is in the ‘Off’ position, the mixer is switched off at the power outlet and the power cord is unplugged.
2. Remove the beater, dough hook or
whisk attachment and mixing bowl from the mixer. Follow instructions in the ‘Assembly and operation’ section of this booklet.
3. Wipe the mixer motor head and
mixer stand with a soft, damp cloth then dry thoroughly.
Wipe any excess food particles from the power cord. Wash the bowl, beater, dough hook, and whisk in warm soapy water with a soft cloth or they can be washed in the dishwasher. Rinse and dry thoroughly.
NOTE
Do not use abrasive scouring pads or cleaners when cleaning the mixing bowl, flat beater, dough hook or whisk as these may scratch the surface. Also ensure that the attachments are not soaked in water for extended periods of time, for example several hours or overnight, as this may damage the finish.
SCRAPER BEATER
1. Wash the scraper beater in warm, soapy
water using a soft cloth or a soft bristled brush. Rinse and dry thoroughly.
2. The Scraper Beater can also be washed
in the dishwasher (top shelf only).
3. A small bottle brush can be used to
clean inside the neck of the Scraper Beater if needed.
STORAGE
Your Breville Scraper Mixer Pro should be kept in a convenient position on your kitchen bench top or in an accessible cupboard.
Always ensure the speed control dial is in the ‘Off’ position, the mixer is switched off at the power point and the power cord is unplugged.
Store the mixing bowl in the bowl locking recess in the mixer Base.
Place the attachments inside the mixing bowl and lower the mixer motor head into the horizontal (closed) position.
The motor head cannot be taken off the base for any purpose.
NOTE
Do not wash or immerse the mixer motor head and mixer base in water or any other liquid. Clean with a soft, damp cloth and dry thoroughly. Do not allow water or any liquid to enter the gear system as damage may result.
19
Loading...
+ 44 hidden pages