Breville BBL605XL User Manual

the Hemisphere™ Control

Made with Eastman Tritan

Instruction Book - Livret d’instructions

copolyester

BBL605XL

BBL605XL_IB_A11_FA.indd 2 9/08/11 10:20 AM

CONGRATULATIONS

on the purchase of your new

Breville Hemisphere™ Control Blender

BBL605XL_IB_A11_FA.indd 2 9/08/11 10:20 AM

CONTENTS

4 Breville recommends safety ﬁrst

8 Know your Breville

Hemisphere

Control Blender

™

10 Operating your Breville

Hemisphere

Control Blender

™

14 Hints & tips

19 Care & cleaning

22 Recipes

36 French

BBL605XL_IB_A11_FA.indd 3 9/08/11 10:20 AM

BREVILLE RECOMMENDS SAFETY FIRST

We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions:

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

TO REDUCE THE RISK OF SEVERE INJURY TO PERSONS, ENSURE THAT IMPORTANT SAFEGUARDS LISTED BELOW ARE FOLLOWED

• Remove any packaging material and

promotional stickers before using the Breville Hemisphere for the ﬁrst time.

• To eliminate a choking hazard for young

children, remove and safely discard the protective cover ﬁtted to the power plug of this appliance.

• Do not place the Breville Hemisphere

Control Blender near the edge of a counter-top or table during operation. Ensure that the surface is level, clean and free of water, ﬂour, etc. Vibration during operation may cause the appliance to move.

• Do not place the Breville Hemisphere

Control Blender on or near a hot gas or electric burner, or where it could touch a heated oven.

• Always ensure the Breville Hemisphere

Control Blender is properly assembled before use. Refer to assembly and operation instructions.

• Use only the blender jug and lid

supplied with the Breville Hemisphere Control Blender.

• Always ensure the blender lid is

ﬁrmly positioned on the blender jug before operating.

Control Blender

™

• Always ensure the Breville Hemisphere

Control Blender is turned off by pressing the Then unplug the cord. Make sure the motor and blades have completely stopped before attempting to move the appliance, or when the Breville

button on the control panel.

Hemisphere™ Control Blender is

not in use and before disassembling, cleaning and storing.

• None of the recipes in this instruction

book are considered a heavy load.

• Do not leave the Breville Hemisphere

Control Blender unattended when in use.

• If food becomes lodged around the

blending blade, turn the Breville Hemisphere™ Control Blender off by pressing the control panel. Then unplug the cord. Make sure the motor and blades have

™

completely stopped before removing the jug from the motor base. Use a spatula to dislodge or stir the food before continuing. Do not use ﬁngers as the blades are sharp.

• Keep hands, ﬁngers, hair, and clothing as

well as spatulas and other utensils away from the blender jug during operation.

• Never place your ﬁngers, hands or

utensils inside the blender jug without unplugging the appliance from the power outlet.

button on the

™

BBL605XL_IB_A11_FA.indd 4 9/08/11 10:20 AM

BREVILLE RECOMMENDS SAFETY FIRST

• Be careful when handling the blending

blade assembly as the blades are very sharp. Be careful when emptying the blender jug and during cleaning. Mishandling of the blades may cause injury.

• Do not remove the blender jug from the

motor base while in operation.

• Do not use the Breville Hemisphere

Control Blender for anything other than food and/or beverage preparation.

• The use of attachments, including

canning jars, not recommended by the manufacturer and may cause risk of injury to persons or damage to the blender.

• Do not operate the Breville

Hemisphere food or liquid in the blender jug.

• CAUTION: Do not process hot or

boiling liquids. Allow to cool before placing into the blender jug.

• Do not subject the blender jug to

extremes of hot or cold, for example, placing a cold jug in hot water or vice versa.

• Keep the appliance clean. Refer to care

and cleaning instructions in this manual.

Control Blender without

™

WARNING

Please do not attempt to use the blender while the “OVERLOAD PROTECTION” is ﬂashing.

• Once the icon stops ﬂashing the

blender has now cooled down and you will be able to use the blender as per instructions. At this point the blender will be in standby mode and you will only need to press the function button to start blending again. However, if you have turned the blender off you will need to turn it back on and only after the icon has stopped ﬂashing return to blending as usual.

• Flashing light indicates ready to operate.

Avoid any contact with blades or moveable parts.

WARNING

Do not operate the blender continuously with heavy load for more than 10 seconds.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Fully unwind the cord before use.

• To protect against electric shock, do not

immerse the cord, plug or motor base in water or any other liquid.

• Do not allow the cord to hang over the

edge of a table or counter-top, touch hot surfaces or become knotted.

• Children should be supervised to ensure

that they do not play with the appliance.

• It is recommended to regularly inspect

the appliance. Do not use the appliance if the power supply cord, plug or appliance becomes damaged in any way. Return appliance to nearest authorized Breville Service Center for repair or replacement.

• Any maintenance other than cleaning

should be performed at an authorised Breville Service Center.

• This appliance is for household use only.

BBL605XL_IB_A11_FA.indd 5 9/08/11 10:20 AM

BREVILLE RECOMMENDS SAFETY FIRST

Do not use in moving vehicles or boats. Do not use outdoors. Do not use this appliance for anything other than its intended use. Misuse may cause injury.

• This appliance is equipped with a

power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.

• If the power outlet is a standard

2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power cord or use an adapter.

BREVILLE ASSIST™ PLUG

Your Breville appliance comes with a unique Assist

™ Plug, conveniently designed with

a ﬁnger hole in the power plug for easy and safe removal from the wall outlet. For safety reasons it is recommended you plug your Breville appliance directly into its own electrical outlet on a dedicated circuit separate from other appliances. If the electric circuit is overloaded with other appliances, your appliance may not function properly. Use in conjunction with a power strip or extension cord is not recommended.

SHORT CORD INSTRUCTIONS

Your Breville appliance is ﬁtted with a short power supply cord as a safety precaution to prevent personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord. Do not allow children to use or be near this appliance without close adult supervision. Longer detachable power supply cords or extension cords are not recommended but may be used if care is exercised. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally

MADE WITH EASTMAN TRITAN™ COPOLYESTER

Key beneﬁts of Eastman Tritan™ copolyester

Your Breville Hemisphere™ Control Blender is made with Eastman Tritan™ copolyester, which is a tough, BPA-free polymer used to make houseware products that can stand up to extreme use and repeated dishwasher cleaning. Products made from Eastman Tritan™ copolyester are impact resistant and shatter resistant and stay clear and durable even after hundreds of cycles using common dishwasher detergents.

Key attributes

• Dishwasher durable

• Tough

FOR HOUSEHOLD USE ONLY SAVE THESE

• BPA free

• Temperature resistant

• Odor-, taste-, and stain-resistant

• Sparkling clarity and gloss

INSTRUCTIONS

BBL605XL_IB_A11_FA.indd 6 9/08/11 10:20 AM

BBL605XL_IB_A11_FA.indd 7 9/08/11 10:20 AM

KNOW

your Breville Hemisphere™ Control Blender

BBL605XL_IB_A11_FA.indd 8 9/08/11 10:20 AM

KNOW YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER

A. Inner measuring lid for adding

ingredients while blending.

B. Large 48oz (1.5L) Eastman Tritan

copolyester Jug unique dual ribs

™

continually pass ingredients onto the blades for well blended results.

C. Die-cast metal base for long lasting,

professional performance.

D. Illuminated buttons for clarity and ease

of reading.

E. Electronic 5 speed control plus PULSE

electronic controls ensure that the RPM speed is maintained for consistent result every time.

F. Breville Assist

™ Lid unique ring pull

design ensures the lid is easy to remove yet sealed tight during operation.

G. Stainless Steel ice-crushing blades

extra wide stainless steel blades are contoured to the base of the jug so there are no food traps.

G L

C D

H. Hemisphere™ Blade and Bowl system

revolutionary blade technology for 100% perfect blending and food processing results.

I. Dishwasher Safe the blender jug is

ergonomically designed for ease of cleaning and is dishwasher safe.

J. Pre-programmed ‘Ice Crush’ and

‘Smoothie’ settings automatically alter speeds to optimize blending results, then turn off automatically.

K. LCD Display counts up on speed settings

and down for pre-programmed settings for complete control when blending.

L. Surgical Grade Stainless Steel Blades

to ensure the blades stay sharp longer they are made from surgical grade stainless steel. The central blades are serrated for extra cutting performance.

BBL605XL_IB_A11_FA.indd 9 9/08/11 10:20 AM

OPERATING

your Breville Hemisphere™ Control Blender

BBL605XL_IB_A11_FA.indd 10 9/08/11 10:20 AM

OPERATING YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER

BEFORE FIRST USE

Before using your Breville Hemisphere™ Control Blender for the ﬁrst time, remove any packaging material and promotional labels. Wash the lid, inner lid, blender jug (refer to Disassembling the blender jug) in warm, soapy water with a soft cloth. Rinse and dry thoroughly. Do not place parts in the dishwasher (with the exception of the blender jug).

The blender jug may be washed in the dishwasher. Ensure the lid has been removed from the blender jug before placing into the dishwasher. The motor base can be wiped with a damp cloth. Dry thoroughly.

Step 3

Add food or liquid into the blender jug ensuring not to exceed the ‘MAX’ mark. Place the blender lid ﬁrmly into position on

NOTE

The blending blades are extremely

the top of the blender jug. Insert the clear inner measuring lid into the blender lid and turn clockwise to lock into position.

sharp. Avoid any contact with ﬁngers and hands.

ASSEMBLING AND ATTACHING THE BLENDER

Step 1

Place the motor base on a ﬂat, dry surface such as a counter-top. Ensure that the motor base is turned off at the the power cord is unplugged.

Step 2

With the blender jug in the upright position place it on the motor base. The handle of the blender can be positioned to the left or right hand side of the appliance.

button and

NOTE

The Breville Hemisphere

Control

™

Blender features a Breville Assist™ Lid. This allows the lid to ﬁt tightly onto the blender jug, avoiding displacement during operation. The ring pull design allows the user to easily remove the lid with a simple leverage action.

BBL605XL_IB_A11_FA.indd 11 9/08/11 10:20 AM

OPERATING YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER

Step 4

Plug power cord into a 110/120V power outlet and turn on.

Step 5

Press the

button on the far left of the control panel to turn the blender on. The

button will illuminate and ﬂash. The LCD timer screen will illuminate with ‘00’ displayed.

NOTE

Flashing light indicates ready to operate. Avoid any contact with moveable parts while in operation.

NOTE

Do not ﬁll the blender jug above the ‘MAX’ line. When the blender jug is ﬁlled at or near the ‘MAX’ line place one hand on the blender lid to avoid displacement of the lid during operation.

Step 6

Select the required speed (1 to 5) by pressing the corresponding speed button. The blender will start to operate and the selected speed button will illuminate. The

button

will illuminate and cease to ﬂash. The ‘Stop’ button will illuminate and ﬂash.

The LCD timer screen will start counting up in one second increments until 60 seconds is reached.

NOTE

Operate the blender only for the appropriate amount of time required – do not over blend.

Step 7

When 60 seconds is reached, the blender will automatically stop blending and the selected speed button and ‘Stop’ button illumination will go out. The

button will illuminate and ﬂash. After a few seconds the LCD timer screen will revert to ‘00’.

NOTE

• The Breville Hemisphere

Control

™

Blender will automatically stop blending after 60 seconds (1 minute). This is a safety feature and restricts wear on the motor.

• To stop blending at any time, press the ‘Stop’ button or the selected speed button. The

button can also be pressed, but this will also turn the appliance off and all illuminations will go out.

• The speed can be changed at any time during the blending process. Each time a new speed is selected its button will illuminate and the previous speed button illumination will go out. The number of seconds on the LCD timer screen will continue to count upwards to 60 seconds unless interrupted.

Step 8

The Breville Hemisphere

Control Blender

™

features two additional functions, ‘ICE CRUSH’ and ‘SMOOTHIE’. These two preprogrammed cycles automatically adjust the blending time and speeds to optimise blending results. Select the required function by pressing the corresponding function button. The blender will start to operate and the selected function button will illuminate. The

button will illuminate and stop ﬂashing. The ‘Stop’ button will illuminate and ﬂash. The LCD timer screen will start counting down in one second increments until ‘00’ is displayed.

BBL605XL_IB_A11_FA.indd 12 9/08/11 10:20 AM

OPERATING YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER

FUNCTION PROGRAMMED TIME

Blend 60 seconds (1 minute) Smoothie 60 seconds (1 minute) Ice / Auto Pulse 60 seconds (1 minute)

When ‘00’ seconds is reached, the blender will automatically cease to operate and the function button and ‘Stop’ button illumination will go out. The will illuminate and ﬂash.

NOTE

The smoothie function has a unique processing technique that blends the denser ingredients at a lower speed, then increases as ingredients thicken. This may happen several times while blending smoothies.

To stop blending at any time, press the ‘Stop’ button or the selected function button. The this will also turn the appliance off and all illuminations will go out.

The maximum amount of ice cubes the blender can blend at any one time is 1 standard ice tray or 250g.

button can also be pressed, but

button

WARNING

Never place anything other than food and liquids in the blender while the motor is running.

Step 9

For ingredients that require short bursts of power, select the ‘PULSE’ function. The ‘PULSE’ button will illuminate and remain illuminated while the button is depressed. When this function is selected, the LCD timer screen will illuminate and count upwards in one second increments during pulsing. Press the ‘PULSE’ button in short bursts until blending is complete.

NOTE

Use the ‘PULSE’ button when the food that is being processed is too thick or coarse to circulate within the blender jug.

Step 10

At the end of use, always ensure the blender is turned off by pressing the on the control panel. Then unplug the cord. Ensure the motor and blades have completely stopped before attempting to move the appliance, or when the Breville Hemisphere and before disassembling, cleaning and storing.

NOTE

• During the blending process, ingredients may stick to the sides of the blender jug. To push the food back onto the blades, press the

to turn blender off and remove the power cord. Remove the lid and use a plastic spatula to scrape down the sides of the jug. Replace the lid before recommencing blending.

• If any moisture or liquid appears on top of the motor base during blending, press the the control panel, and remove the power plug. Remove the blender jug. Wipe the motor base immediately with a dry cloth or paper towel to absorb the liquid. Check the blender jug is correctly assembled.

• Never place anything other than food and liquids in the blender while the motor is running.

Control Blender is not in use

™

button on the control panel

button

button on

BBL605XL_IB_A11_FA.indd 13 9/08/11 10:20 AM

HINTS & TIPS

for your Breville Hemisphere™ Control Blender

BBL605XL_IB_A11_FA.indd 14 9/08/11 10:20 AM

HINTS & TIPS

BLENDING CHART

FOOD PREPARATION & USAGE QUANTITY FUNCTIONS TIME

Raw Vegetables Trim excess, cut into

1 inch pieces Use: stufﬁng, ﬁlling,

puree, soup

2 cups/ 200g

MIX/speed 2 10 - 30 sec

Nuts Remove shells.

Use: cakes, toppings, pastes

Bread or Cookie crumbs

Mayonnaise Mix the egg yolk and

Whipped cream Add sugar or vanilla if

Herbs/spices Chopped or halved.

Smoothie Milk, whole fresh fruits,

Fresh fruit Chopped or whole

Dried fruit Chopped dried fruit.

Cut into 1 inch pieces, break up cookies/ crackers.

Use: cheesecake crust

vinegar. Add the oil. Use: dressing

desired. Use: topping

Use: paste

yogurt, ice cream. Use: milkshakes, frappes

berries. Use: dessert sauce

Use: fruit mince

1½ cups/ 200g

1 cup/100g MIX/speed 2 10 - 30 sec

1½ cups/ 125g

1¼ cups/ 300ml

1¼ cups/ 1 cup

3½ cups/ Max 800ml

2 cups/ 250g

2 cups/ 300g

MIX/speed 2 10 - 30 sec

SNOW/speed 1 BLEND/speed 3

SNOW/speed 1 PULSE

MIX/speed 2 20 - 30 sec

SMOOTHIE 60 secs

BLEND/speed 3 20 - 30 sec

MIX/speed 2 20 - 30 sec

10 - 15 sec 60 sec

10 - 20 secs 1-2 times

Ice Crush.

Use: mixed drinks, cocktails, slurpees

Max 1 tray/250g

ICE CRUSH 60 sec

NOTE

This blending chart should be used as a guide only.

BBL605XL_IB_A11_FA.indd 15 9/08/11 10:20 AM

HINTS & TIPS

PROBLEM EASY SOLUTION

Motor doesn’t start or blade doesn’t rotate

Check that the blender jug and lid are securely into position.

Check that the

button and selected function or

speed setting is illuminated. Check that the power plug is securely inserted into the

power outlet.

Food is unevenly chopped Either too much food is being blended at one time or

the pieces are too large. Try cutting food into smaller pieces of even size and processing a smaller amount per batch.

For best results, the food should be chopped into pieces no larger than 1 inch.

Food is chopped too ﬁne or is watery

Blend for shorter period of time. Use ‘PULSE’ function for more control.

Food sticks to blade and jug The mixture may be too thick. Try adding more liquid

to the mixture and / or use a slower speed.

Blender Overloaded The Breville Hemisphere

Control features a motor

™

protection feature. If the motor is being overloaded the motor will stop and the overload warning icon on the LCD will start to ﬂash. Once the icon stops ﬂashing the blender has now cooled down and you will be able to use the blender as per instructions. At this point the blender will be in standby mode and you will only need to press the function / button that you require to start blending again. However if you have turned the blender off you will need to turn it back on and only if the icon has stopped ﬂashing will the Blender commence blending as usual.

We recommend removing a portion of the mixture, cutting food into smaller pieces or processing smaller amounts per batch.

BBL605XL_IB_A11_FA.indd 16 9/08/11 10:20 AM

HINTS & TIPS

DO’S AND DON’TS

Do’s

• Use the BLEND function for drink or

cocktail making, emulsions such as mayonnaise, dressings, marinades and foods that require mixing until just combined, such as batters, also for pureeing soups and aerating liquids.

• Use a combination of the BLEND and

ICE CRUSH/PULSE functions to process the foods being blended.

• Use the SMOOTHIE function to blend

fruits, ice cream and yogurts into thick smoothies, blended drinks, and milkshakes.

• Use the ICE CRUSH/AUTO PULSE

function for foods that only require short bursts of power.

• Use the ICE CRUSH/AUTO PULSE

function with short bursts of power, when blending drinks containing ice cubes or frozen fruit.

• Ensure all foods are cut into cubes

(approx. 1 square inch) where appropriate to achieve an even result.

• Do not put more than 2 cups of warm

ingredients into the blender jug before blending commences. After the blending process has begun and the blades are turning you may slowly add another 1½ cups of ingredients through the opening in the lid if desired.

• Thick mixtures puree more efﬁciently

if the Breville Hemisphere Blender is ¼ to ½ full.

Control

™

• When using several ingredients,

place liquid ingredients in the blender jug before solid ingredients, unless speciﬁed in the recipe. When blending thick or dry mixtures it may be necessary to stop the Breville Hemisphere

Control Blender and

™

scrape down the sides of the blender jug with a plastic or rubber spatula, once or twice during blending.

Don'ts

• Do not use metal utensils as they may

damage the blades or blender jug.

• Do not operate a heavy mixture for

more than 10 seconds. For normal blending tasks, for example, mayonnaise, dressings etc., do not operate for longer than 1 minute at one time without turning off the Breville Hemisphere™ Control Blender and stirring the ingredients, and then continue blending.

• Do not operate the Breville

Hemisphere™ Control Blender without having the blender lid in position. To add additional ingredients while blending, remove the inner lid and place ingredients through the opening in the lid.

• Do not place any objects, other than food

or liquid, into the Breville Hemisphere™ Control Blender while the motor is running.

• Do not use the blender jug to store food.

• The blender will not knead dough or

mash potatoes.

• Do not remove the blender jug while

the Breville Hemisphere

Control

™

Blender is operating. Always make sure the blender is turned off by pressing the

button and unplug the power

cord from the power outlet.

BBL605XL_IB_A11_FA.indd 17 9/08/11 10:20 AM

PAGE HEADER.....

HINTS & TIPS

• Do not overload the Breville

Hemisphere

Control Blender with

™

more than the speciﬁed quantity of ingredients as doing so could cause the motor to stall. Turn the blender off by pressing the

button on the control panel and unplug the cord. Remove a portion of the mixture from the blender jug before continuing.

• Do not place hot or boiling ingredients

into the Breville Hemisphere

Control

™

Blender; allow to cool before placing into the blender jug.

• Do not place the Breville Hemisphere

™

Control Blender near the edge of a counter-top or table during operation. Ensure that the surface is level, clean and free of water, ﬂour and other substances. Vibration during operation may cause the appliance to move.

BBL605XL_IB_A11_FA.indd 18 9/08/11 10:20 AM

CARE & CLEANING

for your Breville Hemisphere™ Control Blender

BBL605XL_IB_A11_FA.indd 19 9/08/11 10:20 AM

CARE & CLEANING

DISASSEMBLING YOUR BLENDER FOR CLEANING

Step 1.

Always ensure the Breville Hemisphere Control Blender is off by pressing the ‘Power’ button on the control panel. Then unplug the power cord.

Step 2.

Remove the blender jug from the motor base by grasping the handle and lifting the jug in an upward direction.

Step 3.

Remove the lid and wash as per care and cleaning instructions.

™

REASSEMBLING YOUR BLENDER JUG AFTER CLEANING.

Ensure all parts are clean and completely dry thoroughly before placing blender jug onto blender base.

CLEANING THE MOTOR BASE

Wipe the motor base with a soft, damp cloth then dry thoroughly.

Wipe any excess food particles from the power cord.

CLEANING THE BLENDER JUG, LID, AND INNER MEASURING LID

Wash all parts in warm soapy water with a soft cloth. Use a brush to dislodge stubborn foods. Rinse and dry thoroughly.

NOTE

Periodically, run a cycle with the jar ﬁlled L with warm soapy water to help clean in between the gaskets/washers of the blade assembly as fruit juices can get in and act somewhat like an adhesive which would make the blades difﬁcult to turn and therefore put extra pressure and resistance on the motor.

NOTE

Blades are sharp please use care when cleaning around the blades.

When cleaning the blender jug it is always a good idea to clean immediately after use to avoid food sticking to the blades and jug. Place 1-2 cups of warm soapy water into the jug with the lid on and inner lid in place and blend for 5-10 seconds on a low speed which will help clean the blades and jug. Then rinse jug in cold water and dry thoroughly.

NOTE

Do not use abrasive scouring pads or cleaners when cleaning the motor base as they may scratch the surface.

BBL605XL_IB_A11_FA.indd 20 9/08/11 10:20 AM

The blender lid may be washed in the dishwasher on the top shelf only and on a standard wash cycle. The blender jug may be placed in the bottom shelf of the dishwasher on a standard cycle only.

CARE & CLEANING

REMOVING STUBBORN OR STRONG FOOD STAINS AND ODORS

Strong smelling foods such as garlic, ﬁsh and some vegetables such as carrots may leave an odor or stain on the blender jug and lid. To remove, soak blender jug and lid for 5 minutes in warm soapy water. Then wash with a mild detergent and warm water, rinse well and dry thoroughly.

STORAGE

Store your Breville Hemisphere™ Control Blender upright with the blender jug, lid and inner lid assembled and inserted on the motor base or beside it. Do not place anything on top.

WARNING

The blending blades are extremely sharp. Avoid any contact with ﬁngers and hands. Use caution when handling and storing.

BBL605XL_IB_A11_FA.indd 21 9/08/11 10:20 AM

+ 49 hidden pages