Breville BBL605XL User Manual 2
the Hemisphere™ Control
Instruction Book - Livret d’instructions
Suits all BBL605XL models
Pour tous les modeles BBL605XL
CONGRATULATIONS
on the purchase of your new
Breville product
Register online for product support
and exclusive offers.
USA Consumers: www.brevilleusa.com
Canadian Consumers: www.breville.ca
*Registering is not a substitute for proof of purchase when submitting a Warranty Claim.
*
CONTENTS
4 Breville recommends safety first
8 Know your Breville product
10 Operating your Breville product
14 Hints & tips
19 Care & cleaning
22 Recipes
36 French
3
BREVILLE RECOMMENDS SAFETY FIRST
We at Breville are very safety conscious. We design and manufacture consumer products
with the safety of you, our valued customer, foremost in mind. In addition, we ask that
you exercise a degree of care when using any electrical appliance and adhere to the
following precautions:
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Remove any packaging material and
promotional stickers before using the
Breville Hemisphere™ Control Blender
for the first time.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug
of this appliance.
• Do not place the Breville Hemisphere™
Control Blender near the edge of a
counter-top or table during operation.
Ensure that the surface is level, clean
and free of water, flour, etc. Vibration
during operation may cause the
appliance to move.
• Do not place the Breville Hemisphere™
Control Blender on or near a hot gas or
electric burner, or where it could touch a
heated oven.
• Always ensure the Breville Hemisphere™
Control Blender is properly assembled
before use. Refer to assembly and
operation instructions.
• Use only the blender jug and lid
supplied with the Breville Hemisphere™
Control Blender.
• Always ensure the blender lid is
firmly positioned on the blender jug
before operating.
• None of the recipes in this instruction
book are considered a heavy load.
• Do not leave the Breville Hemisphere™
Control Blender unattended when in use.
• Always ensure the Breville Hemisphere
Control Blender is turned off by pressing
the button on the control panel.
Then unplug the cord. Make sure the
motor and blades have completely
stopped before attempting to move
the appliance, or when the Breville
Hemisphere™ Control Blender is
not in use and before disassembling,
cleaning and storing.
• If food becomes lodged around the
blending blade, turn the Breville
Hemisphere™ Control Blender off by
pressing the button on the
control panel. Then unplug the cord.
Make sure the motor and blades have
completely stopped before removing the
jug from the motor base. Use a spatula
to dislodge or stir the food before
continuing. Do not use fingers as the
blades are sharp.
• Keep hands, fingers, hair, and clothing as
well as spatulas and other utensils away
from the blender jug during operation.
• Never place your fingers, hands or
utensils inside the blender jug without
unplugging the appliance from the
power outlet.
• Be careful when handling the blending
blade assembly as the blades are very
sharp. Be careful when emptying
the blender jug and during cleaning.
Mishandling of the blades may
cause injury.
• Do not remove the blender jug from the
motor base while in operation.
™
4
BREVILLE RECOMMENDS SAFETY FIRST
• Do not use the Breville Hemisphere™
Control Blender for anything other than
food and/or beverage preparation.
• The use of attachments, including
canning jars, not recommended by
the manufacturer and may cause risk
of injury to persons or damage to the
blender.
• Do not operate the Breville
Hemisphere™ Control Blender without
food or liquid in the blender jug.
• CAUTION: Do not process hot or
boiling liquids. Allow to cool before
placing into the blender jug.
• Do not subject the blender jug to
extremes of hot or cold, for example,
placing a cold jug in hot water or
vice versa.
• Keep the appliance clean. Refer to care
and cleaning instructions in this manual.
WARNING
Please do not attempt to use the
blender while the “OVERLOAD
PROTECTION” is flashing.
• Once the icon stops flashing the
blender has now cooled down and you
will be able to use the blender as per
instructions. At this point the blender
will be in standby mode and you will
only need to press the function button
to start blending again. However, if you
have turned the blender off you will need
to turn it back on and only after the icon
has stopped flashing return to blending
as usual.
• Flashing light indicates ready to operate.
Avoid any contact with blades or
moveable parts.
WARNING
Do not operate the blender
continuously with heavy load for
more than 10 seconds.
IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES
• Fully unwind the cord before use.
• To protect against electric shock, do not
immerse the cord, plug or motor base in
water or any other liquid.
• Do not allow the cord to hang over the
edge of a table or counter-top, touch hot
surfaces or become knotted.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect
the appliance. Do not use the appliance
if the power supply cord, plug or
appliance becomes damaged in any way.
Return appliance to nearest authorized
Breville Service Center for repair or
replacement.
• Any maintenance other than cleaning
should be performed at an authorised
Breville Service Center.
• This appliance is for household use only.
Do not use in moving vehicles or boats.
Do not use outdoors. Do not use this
appliance for anything other than its
intended use. Misuse may cause injury.
• This appliance is equipped with a
power cord having a grounding wire
with a grounding plug. The appliance
must be grounded using a 3-hole
properly grounded outlet. In the event
of an electrical short circuit, grounding
reduces the risk of electrical shock.
• If the power outlet is a standard
2-prong wall outlet, it is your personal
responsibility and obligation to have
it replaced with a properly grounded
3-prong wall outlet.
5
5
BREVILLE RECOMMENDS SAFETY FIRST
• Do not, under any circumstances, cut or
remove the third (ground) prong from
the power cord or use an adapter.
BREVILLE ASSIST™ PLUG
Your Breville appliance comes with a unique
Assist™ Plug, conveniently designed with
a finger hole in the power plug for easy
and safe removal from the wall outlet. For
safety reasons it is recommended you
plug your Breville appliance directly into
its own electrical outlet on a dedicated
circuit separate from other appliances. If
the electric circuit is overloaded with other
appliances, your appliance may not function
properly. Use in conjunction with a power
strip or extension cord is not recommended.
SHORT CORD INSTRUCTIONS
Your Breville appliance is fitted with a short
power supply cord as a safety precaution to
prevent personal injury or property damage
resulting from pulling, tripping or becoming
entangled with a longer cord. Do not allow
children to use or be near this appliance
without close adult supervision. Longer
detachable power supply cords or extension
cords are not recommended but may be
used if care is exercised. If an extension cord
is used, (1) the marked electrical rating of
the cord set or extension cord should be at
least as great as the electrical rating of the
appliance, (2) the cord should be arranged
so that it will not drape over the countertop
or tabletop where it can be pulled on by
children or tripped over unintentionally.
Key benefits of Eastman Tritan™
copolyester
Your Breville Hemisphere™ Control Blender
is made with Eastman Tritan™ copolyester,
which is a tough, BPA-free polymer used to
make houseware products that can stand
up to extreme use and repeated dishwasher
cleaning. Products made from
Eastman Tritan™ copolyester are impact
resistant and shatter resistant and stay clear
and durable even after hundreds of cycles
using common dishwasher detergents.
Key attributes
• Dishwasher durable
• Tough
• BPA free
• Temperature resistant
• Odor-, taste-, and stain-resistant
• Sparkling clarity and gloss
MADE WITH EASTMAN
TRITAN™ COPOLYESTER
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
6
7
KNOW
your Breville product
KNOW YOUR BREVILLE PRODUCT
A
F
B
I
H
J
A. Inner measuring lid for adding
ingredients while blending.
B. Large 48oz (1.5L) Eastman Tritan
copolyester Jug unique dual ribs
™
continually pass ingredients onto the
blades for well blended results.
C. Die-cast metal base for long lasting,
professional performance.
D. Illuminated buttons for clarity and ease
of reading.
E. Electronic 5 speed control plus PULSE
electronic controls ensure that the RPM
speed is maintained for consistent result
every time.
F. Breville Assist™ Lid unique ring pull
design ensures the lid is easy to remove
yet sealed tight during operation.
G. Stainless Steel ice-crushing blades
extra wide stainless steel blades are
contoured to the base of the jug so there
are no food traps.
G
L
C
D
E
K
H. Hemisphere™ Blade and Bowl system
revolutionary blade technology for
100% perfect blending and food
processing results.
I. Dishwasher Safe the blender jug is
ergonomically designed for ease of
cleaning and is dishwasher safe.
J. Pre-programmed ‘Ice Crush’ and
‘Smoothie’ settings automatically alter
speeds to optimize blending results,
then turn off automatically.
K. LCD Display counts up on speed settings
and down for pre-programmed settings
for complete control when blending.
L. Surgical Grade Stainless Steel Blades
to ensure the blades stay sharp longer
they are made from surgical grade
stainless steel. The central blades are
serrated for extra cutting performance.
9
OPERATING
your Breville product
OPERATING YOUR BREVILLE PRODUCT
BEFORE FIRST USE
Before using your Breville Hemisphere™
Control Blender for the first time, remove
any packaging material and promotional
labels. Wash the lid, inner lid, blender jug
(refer to Disassembling the blender jug) in
warm, soapy water with a soft cloth. Rinse
and dry thoroughly. Do not place parts in
the dishwasher (with the exception of the
blender jug).
The blender jug may be washed in the
dishwasher. Ensure the lid has been removed
from the blender jug before placing into the
dishwasher. The motor base can be wiped
with a damp cloth. Dry thoroughly.
NOTE
The blending blades are extremely
sharp. Avoid any contact with fingers
and hands.
ASSEMBLING AND ATTACHING
THE BLENDER
Step 3
Add food or liquid into the blender jug
ensuring not to exceed the ‘MAX’ mark.
Place the blender lid firmly into position on
the top of the blender jug. Insert the clear
inner measuring lid into the blender lid and
turn clockwise to lock into position.
Step 1
Place the motor base on a flat, dry surface
such as a counter-top. Ensure that the motor
base is turned off at the button and
the power cord is unplugged.
Step 2
With the blender jug in the upright position
place it on the motor base. The handle of the
blender can be positioned to the left or right
hand side of the appliance.
NOTE
The Breville Hemisphere™ Control
Blender features a Breville Assist™
Lid. This allows the lid to fit tightly
onto the blender jug, avoiding
displacement during operation. The
ring pull design allows the user to
easily remove the lid with a simple
leverage action.
11
OPERATING YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER
Step 4
Plug power cord into a 110/120V power
outlet and turn on.
Step 5
Press the button on the far left of
the control panel to turn the blender on.
The button will illuminate and
flash. The LCD timer screen will illuminate
with ‘00’ displayed.
NOTE
Flashing light indicates ready to operate.
Avoid any contact with moveable parts
while in operation.
NOTE
Do not fill the blender jug above the
‘MAX’ line. When the blender jug is filled
at or near the ‘MAX’ line place one hand
on the blender lid to avoid displacement
of the lid during operation.
Step 6
Select the required speed (1 to 5) by pressing
the corresponding speed button. The blender
will start to operate and the selected speed
button will illuminate. The button
will illuminate and cease to flash.
The STOP button will illuminate and flash.
The LCD timer screen will start counting up
in one second increments until 60 seconds
is reached.
NOTE
Operate the blender only for the
appropriate amount of time required –
do not over blend.
Step 7
When 60 seconds is reached, the blender
will automatically stop blending and the
selected speed button and STOP button
illumination will go out. The button
will illuminate and flash. After a few seconds
the LCD timer screen will revert to ‘00’.
NOTE
• The Breville Hemisphere™ Control
Blender will automatically stop
blending after 60 seconds
(1 minute). This is a safety feature
and restricts wear on the motor.
• To stop blending at any time, press
the STOP button or the selected
speed button. The button
can also be pressed, but this will
also turn the appliance off and all
illuminations will go out.
• The speed can be changed at any
time during the blending process.
Each time a new speed is selected
its button will illuminate and the
previous speed button illumination
will go out. The number of seconds
on the LCD timer screen will
continue to count upwards to
60 seconds unless interrupted.
Step 8
The Breville Hemisphere™ Control Blender
features two additional functions, ‘ICE
CRUSH’ and ‘SMOOTHIE’. These two preprogrammed cycles automatically adjust
the blending time and speeds to optimise
blending results. Select the required
function by pressing the corresponding
function button. The blender will start to
operate and the selected function button
will illuminate. The button will
illuminate and stop flashing. The STOP
button will illuminate and flash. The LCD
timer screen will start counting down in one
second increments until ‘00’ is displayed.
12
OPERATING YOUR BREVILLE HEMISPHERE™ CONTROL BLENDER
FUNCTION PROGRAMMED TIME
Blend 60 seconds (1 minute)
Smoothie 60 seconds (1 minute)
Ice / Auto Pulse 60 seconds (1 minute)
When ‘00’ seconds is reached, the blender
will automatically cease to operate and
the function button and STOP button
illumination will go out. The button
will illuminate and flash.
NOTE
The smoothie function has a unique
processing technique that blends the
denser ingredients at a lower speed,
then increases as ingredients thicken.
This may happen several times while
blending smoothies.
To stop blending at any time, press the
STOP button or the selected function
button. The button can also be
pressed, but this will also turn the appliance
off and all illuminations will go out.
The maximum amount of ice cubes the
blender can blend at any one time is 1
standard ice tray or 250g.
WARNING
Never place anything other than food
and liquids in the blender while the
motor is running.
Step 9
For ingredients that require short bursts
of power, select the PULSE function. The
PULSE button will illuminate and remain
illuminated while the button is depressed.
When this function is selected, the LCD
timer screen will illuminate and count
upwards in one second increments during
pulsing. Press the PULSE button in short
bursts until blending is complete.
NOTE
Use the PULSE button when the
food that is being processed is too
thick or coarse to circulate within the
blender jug.
Step 10
At the end of use, always ensure the blender
is turned off by pressing the button
on the control panel. Then unplug the
cord. Ensure the motor and blades have
completely stopped before attempting to
move the appliance, or when the Breville
Hemisphere™ Control Blender is not in use
and before disassembling, cleaning and
storing.
NOTE
• During the blending process,
ingredients may stick to the sides
of the blender jug. To push the food
back onto the blades, press the
button on the control panel
to turn blender off and remove the
power cord. Remove the lid and use
a plastic spatula to scrape down
the sides of the jug. Replace the lid
before recommencing blending.
• If any moisture or liquid appears
on top of the motor base during
blending, press the button on
the control panel, and remove the
power plug. Remove the blender jug.
Wipe the motor base immediately
with a dry cloth or paper towel to
absorb the liquid. Check the blender
jug is correctly assembled.
• Never place anything other than
food and liquids in the blender while
the motor is running.
13
HINTS & TIPS
for your Breville product
HINTS & TIPS
BLENDING CHART
FOOD PREPARATION & USAGE QUANTITY FUNCTIONS TIME
Raw Vegetables Trim excess, cut into
1 inch pieces
Use: stuffing, filling,
puree, soup
2 cups/
200g
MIX/speed 2 10 - 30 sec
Nuts Remove shells.
Use: cakes, toppings,
pastes
Bread or Cookie
crumbs
Mayonnaise Mix the egg yolk and
Whipped cream Add sugar or vanilla if
Herbs/spices Chopped or halved.
Smoothie Milk, whole fresh fruits,
Fresh fruit Chopped or whole
Dried fruit Chopped dried fruit.
Cut into 1 inch pieces,
break up cookies/
crackers.
Use: cheesecake crust
vinegar. Add the oil.
Use: dressing
desired.
Use: topping
Use: paste
yogurt, ice cream.
Use: milkshakes, frappes
berries.
Use: dessert sauce
Use: fruit mince
1½ cups/
200g
1 cup/100g MIX/speed 2 10 - 30 sec
1½ cups/
125g
1¼ cups/
300ml
1¼ cups/
1 cup
3½ cups/
Max 800ml
2 cups/
250g
2 cups/
300g
MIX/speed 2 10 - 30 sec
SNOW/speed 1
BLEND/speed 3
SNOW/speed 1
PULSE
MIX/speed 2 20 - 30 sec
SMOOTHIE 60 secs
BLEND/speed 3 20 - 30 sec
MIX/speed 2 20 - 30 sec
10 - 15 sec
60 sec
10 - 20 secs
1-2 times
Ice Crush.
Use: mixed drinks,
cocktails, slurpees
NOTE
This blending chart should be used as
a guide only.
Max
1 tray/250g
ICE CRUSH 60 sec
15
HINTS & TIPS
PROBLEM EASY SOLUTION
Motor doesn’t start or blade
doesn’t rotate
Check that the blender jug and lid are securely into
position.
Check that the button and selected function or
speed setting is illuminated.
Check that the power plug is securely inserted into the
power outlet.
Food is unevenly chopped Either too much food is being blended at one time or
the pieces are too large. Try cutting food into smaller
pieces of even size and processing a smaller amount
per batch.
For best results, the food should be chopped into pieces
no larger than 1 inch.
Food is chopped too fine or
is watery
Blend for shorter period of time. Use PULSE function
for more control.
Food sticks to blade and jug The mixture may be too thick. Try adding more liquid
to the mixture and / or use a slower speed.
Blender Overloaded The Breville Hemisphere™ Control features a motor
protection feature. If the motor is being overloaded the
motor will stop and the overload warning icon on the
LCD will start to flash. Once the icon stops flashing the
blender has now cooled down and you will be able to
use the blender as per instructions. At this point the
blender will be in standby mode and you will only need
to press the function / button that you require to start
blending again. However if you have turned the blender
off you will need to turn it back on and only if the
icon has stopped flashing will the Blender commence
blending as usual.
We recommend removing a portion of the mixture,
cutting food into smaller pieces or processing smaller
amounts per batch.
16
HINTS & TIPS
DO’S AND DON’TS
Do’s
• Use the BLEND function for drink or
cocktail making, emulsions such as
mayonnaise, dressings, marinades and
foods that require mixing until just
combined, such as batters, also for
pureeing soups and aerating liquids.
• Use a combination of the BLEND and
ICE CRUSH/PULSE functions to
process the foods being blended.
• Use the SMOOTHIE function to blend
fruits, ice cream and yogurts into
thick smoothies, blended drinks, and
milkshakes.
• Use the ICE CRUSH/AUTO PULSE
function for foods that only require short
bursts of power.
• Use the ICE CRUSH/AUTO PULSE
function
with short bursts of power, when
blending drinks containing ice cubes
or frozen fruit.
• Ensure all foods are cut into cubes
(approx. 1 square inch) where
appropriate to achieve an even result.
• Do not put more than 2 cups of warm
ingredients into the blender jug before
blending commences. After the blending
process has begun and the blades are
turning you may slowly add another 1½
cups of ingredients through the opening
in the lid if desired.
• Thick mixtures puree more efficiently
if the Breville Hemisphere™ Control
Blender is ¼ to ½ full.
• When using several ingredients,
place liquid ingredients in the
blender jug before solid ingredients,
unless specified in the recipe. When
blending thick or dry mixtures it
may be necessary to stop the Breville
Hemisphere™ Control Blender and
scrape down the sides of the blender jug
with a plastic or rubber spatula, once or
twice during blending.
Don'ts
• Do not use metal utensils as they may
damage the blades or blender jug.
• Do not operate a heavy mixture for
more than 10 seconds. For normal
blending tasks, for example, mayonnaise,
dressings etc., do not operate for longer
than 1 minute at one time without
turning off the Breville Hemisphere™
Control Blender and stirring the
ingredients, and then continue blending.
• Do not operate the Breville
Hemisphere™ Control Blender without
having the blender lid in position.
To add additional ingredients while
blending, remove the inner lid and place
ingredients through the opening in the
lid.
• Do not place any objects, other than food
or liquid, into the Breville Hemisphere™
Control Blender while the motor is
running.
• Do not use the blender jug to store food.
• The blender will not knead dough or
mash potatoes.
• Do not remove the blender jug while
the Breville Hemisphere™ Control
Blender is operating. Always make sure
the blender is turned off by pressing the
button and unplug the power
cord from the power outlet.
17
PAGE HEADER.....
HINTS & TIPS
• Do not overload the Breville
Hemisphere™ Control Blender with
more than the specified quantity of
ingredients as doing so could cause
the motor to stall. Turn the blender
off by pressing the button on
the control panel and unplug the cord.
Remove a portion of the mixture from
the blender jug before continuing.
• Do not place hot or boiling ingredients
into the Breville Hemisphere™ Control
Blender; allow to cool before placing into
the blender jug.
• Do not place the Breville Hemisphere™
Control Blender near the edge of a
counter-top or table during operation.
Ensure that the surface is level, clean and
free of water, flour and other substances.
Vibration during operation may cause the
appliance to move.
18
CARE & CLEANING
for your Breville product
19
CARE & CLEANING
DISASSEMBLING YOUR BLENDER
FOR CLEANING
Step 1.
Always ensure the Breville Hemisphere™
Control Blender is off by pressing the
‘Power’ button on the control panel. Then
unplug the power cord.
Step 2.
Remove the blender jug from the motor base
by grasping the handle and lifting the jug in
an upward direction.
Step 3.
Remove the lid and wash as per care and
cleaning instructions.
REASSEMBLING YOUR BLENDER
JUG AFTER CLEANING.
Ensure all parts are clean and completely
dry thoroughly before placing blender jug
onto blender base.
CLEANING THE MOTOR BASE
Wipe the motor base with a soft, damp cloth
then dry thoroughly.
Wipe any excess food particles from the
power cord.
CLEANING THE BLENDER JUG, LID,
AND INNER MEASURING LID
Wash all parts in warm soapy water with a
soft cloth. Use a brush to dislodge stubborn
foods. Rinse and dry thoroughly.
NOTE
Periodically, run a cycle with the jar
filled L with warm soapy water to
help clean in between the
gaskets/washers of the blade
assembly as fruit juices can get in
and act somewhat like an adhesive
which would make the blades difficult
to turn and therefore put extra
pressure and resistance on the motor.
NOTE
Blades are sharp please use care when
cleaning around the blades.
When cleaning the blender jug
it is always a good idea to clean
immediately after use to avoid food
sticking to the blades and jug. Place
1-2 cups of warm soapy water into
the jug with the lid on and inner lid in
place and blend for 5-10 seconds on
a low speed which will help clean the
blades and jug. Then rinse jug in cold
water and dry thoroughly.
NOTE
Do not use abrasive scouring pads
or cleaners when cleaning the motor
base as they may scratch the surface.
20
The blender lid may be washed in the
dishwasher on the top shelf only and on a
standard wash cycle. The blender jug may be
placed in the bottom shelf of the dishwasher
on a standard cycle only.
CARE & CLEANING
REMOVING STUBBORN OR STRONG
FOOD STAINS AND ODORS
Strong smelling foods such as garlic, fish
and some vegetables such as carrots may
leave an odor or stain on the blender jug and
lid. To remove, soak blender jug and lid for
5 minutes in warm soapy water. Then wash
with a mild detergent and warm water, rinse
well and dry thoroughly.
STORAGE
Store your Breville Hemisphere™ Control
Blender upright with the blender jug, lid
and inner lid assembled and inserted on
the motor base or beside it. Do not place
anything on top.
WARNING
The blending blades are extremely
sharp. Avoid any contact with fingers
and hands. Use caution when handling
and storing.
21
RECIPES
Loading...