Bradley Corporation S1944011ABC, S1944011BBC Installation Manual

Installation

S1944011ABC

Hand-Held Drench Hose and Eye/
Face Wash (with 12' Hose)

S1944011ABC

S1944011BBC

Hand-Held Drench Hose and Angled
Eye/Face Wash (with 12' Hose)

Table of Contents

Pre-Installation Information ..................... 2

Installation Instructions ........................ 3

Assembly of Components and Parts List .......... 4

S1944011BBC

215-1692 Rev. C; ECN 14-05-013
© 2014 Bradley
Page 1 of 4 7/22/2014

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com

S1944011ABC, S1944011BBC Installation

IMPORTANT

Installation

R

WI 53051

alls,

HENTLICH ZU
WEEK
WÖC

P.O. Box 309, Menomonee F

DAIRE

e(s) each week and sign

UNIT EACH

y malfunctions immediatel

hentlich im

TEST THIS

hrift. Jeglic

DIESES GERÄT 1ST
ESSAI HEBDOMA

Test-operate valv
Report an

Ventil(e) wöc

t immédiatement.

durch Untersc

Test le fonctionnement des v
signe en bas. S'il y à quelqu

un rappor

Date

Datum
Date

114-051

PRÜFEN.

Testbetrieb prüfen,
he Störung sofor

Signed
Unterschrift

below.

bestätigt
t melden.

y.

alves chaque semaine et
e chose qui ne v

Date Signed

Signe

THIS
SIDE
UP

a pas fait

Signed
Signed

Date
Date

P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA

TEL: 1-800-BRADLEY FAX: [phone])

http://www.bradleycorp.com

Packing List

•

•

•

•

Read this installation manual completely to ensure proper installation, then file it with the

owner or maintenance department. Compliance and conformity to drain requirements and
other local codes and ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding

any packaging material. If any parts are missing, do not begin installation until you obtain
the missing parts.

Flush the water supply lines before beginning installation and after installation is complete.

Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be
“ON” at all times. Provisions shall be made to prevent unauthorized shutoff.

The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley

plumbed emergency fixtures require a minimum of 30 PSI (0.21 MPa) flowing pressure.
Flushing fluid should be tepid per ANSI Z358.1.

The inspection and testing results of this equipment should be recorded weekly to verify

proper operation. This equipment should be inspected annually to ensure compliance with
ANSI Z358.1.

Workers who may come in contact with potentially hazardous materials should be trained

regarding the placement and proper operation of emergency equipment per ANSI Z358.1.

For questions regarding the operation or installation of this product, visit www.bradleycorp.

com or call 800.BRADLEY (800.272.3539).

Product warranties and service parts information may also be found under ”Products” on our

web site at bradleycorp.com.

NOTICE! Avoid cleaners containing organic solvents, alcohols, and hydrocarbons.

Rinse with water after cleaning.

Supplies Required:

• Teflon tape and/or pipe sealant

• ½" NPT water supply inlet (30–90 psi)

• (2) ¼-20 screws (stainless steel recommended) and anchors

• Sign-mounting hardware

• Backflow prevention device as required by UPC, IPC and/or local plumbing codes

 Local codes may require the installation of a backflow prevention valve to complete proper installation. Compliance with

local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly.
Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from
Bradley Corporation.

2

7/22/2014 Bradley • 215-1692 Rev. C; ECN 14-05-013