Bosch TDA3610GB, TDA3605GB User Manual

DO NOT de-scale or clean the water tank with cleaning products

or solvents, as these could cause the iron to drip when using the
steam function.

DO NOT use a “professional steam cleaner” for cleaning the
appliance.

DO NOT use sharp objects or abrasive products to clean the
soleplate or any other part of the appliance. To keep the soleplate
in good condition, do not allow it to come into contact with metal
objects.

GUARANTEE TERMS

The terms of the guarantee for this appliance are in accordance with
that stated by our representative for the country in which it is sold.
Details of those conditions can be obtained from the retailer from
whom the appliance was purchased. The SALES RECEIPT must
be presented when making any claims against the terms of this
guarantee. We reserve the right to make technical modifications.

Environmental Care

This iron has been designed according to ecological criteria,
related to the sustainable development, analysing its whole
lifecycle - from material selection to its later reuse or recycling

- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.

Before throwing a used appliance away, you should make it
noticeably inoperable e.g. cut off the mains lead and be certain to
dispose of it in accordance with current laws and regulations.

Your retailer, town council or local council can give you detailed
information about these.

This appliance is labelled in accordance with
European Directive 2002/96/EG concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).

The guideline determines the framework for the return
and recycling of used appliances as applicable throughout
the EU.

Important

This appliance has been designed exclusively for domestic use
and must not be used for industrial purposes.

Carefully read through the operating instructions for the appliance
and safeguard them for future reference.

002 TDA36..GB/03/10

Customer Service

Great Britain

Bosch Customer Service

Grand Union House

Old Wolverton Road

Milton Keynes

MK12 5PT

UK [phone]

IRL [phone]

www.bosch-home.co.uk

Operating instructions

Solving Minor Problems Yourself

Problem Possible Causes Solution

Iron does not
work or is not
heating up

Temperature control (I) on a
very low setting

Turn the temperature
control to the desired
position

Connection problems Check that the plug is

inserted into the mains
socket correctly

The automatic shut-off
system (*) has been activated

Move the iron gently from
side to side to re-start it

Iron is not
steaming

There is no water in the tank Fill the water tank
The steam regulator (C) is in

the «0» position

Set the steam regulator
to the relevant position

Scale obstruction of internal
components

Remove the steam
regulator (C) and clean
it. If this does not help
contact an Authorised
Technical Service Centre

Water is
dripping from
the holes in
the soleplate

Temperature control (I) setting
is too low

Set the temperature
control within the steam

area (between the “••”

and “max”) or turn the
steam regulator (C) to «0»

You have pressed the shot of
steam button (A) repeatedly
without waiting for 5 seconds
between each press

Wait 5 seconds between
each press of the jet of
steam button

Water has been left in the
tank (F) when the soleplate
was cold, with the steam
regulator (C) set at «1» or «2»

Always empty the tank
after ironing and set the
steam regulator to «0»
after ironing and when
filling the tank

Tap or part distilled water has
not been used (see “Filling the
water tank” section) or other
products such as fragrant
water have been added to the
tank

Mix distilled water with
tap water as directed
in the “Filling the water
tank” section and never
add any other products
to the water tank

Deposits come
out through
the holes in the
soleplate

Traces of lime scale are
coming out of the steam
chamber

Carry out a cleaning
cycle (see Multiple de­scaling system section)

Spray does not
work

No water in the tank. Add water to the water

tank.

Obstructed mechanism. Contact an Authorised

Technical Service Centre.

The iron
begins to
smoke when
switched on.

During first use: Certain
components on the appliance
have been lightly greased at the
factory and may produce a little
smoke when initially heated.

This is completely normal
and will stop after a short
while.

Flashing lamp
on top of
handle (*)

Auto-shut off has been
activated.

Move the iron gently
fromside to side to re­start it. The lamp (N) will
then flash once before it
re-heats

Thank you for buying the TDA36 steam iron from Bosch. This iron
has a lightweight design and is built to perform

These instructions contain valuable information about the unique
features of this iron and some hints to make ironing easier for
you.

Please visit www.bosch-home.co.uk for more product
information or to register your product, just follow the link
to the Online guarantee registration.

Before using the iron for the first time

Please carry out the following steps:

1. Remove the protective cover from the soleplate before using
the iron.

2. While the iron is unplugged, fill the water tank (F) with tap
water

3. Plug the appliance into the mains and set the temperature
control (I) to the “max” position by lining it up with the pointer
(H).

4. When the iron has reached the correct temperature (the pilot
lamp K goes out), set the steam regulator (C) to the «2» position
by lining it up with the pointer (D).

5. Hold the iron horizontally and repeatedly press the shot of steam
button (A). Any residue should come out of the soleplate (G).
It may smoke and smell – this is normal and will cease after a
short while.

6. If necessary, carefully clean the soleplate down with a dry, folded
cloth

Cleaning and Maintenance

Attention ! Risk of burns !

For general cleaning, follow the information below:

Problem Solution

Dirty/lightly
marked iron body
or soleplate

Clean the body of iron or soleplate with a
damp cloth then dry it.

Mark develops on
soleplate during
use

Set the iron to its maximum temperature
setting. Rub the iron a few times over
with a dry cotton cloth folded several
times.

Heavily stained
soleplate

While the iron is cold, iron a linen cloth
soaked in white vinegar. Then dampen a
cloth with water and wipe the soleplate
clean and dry thoroughly.

TDA 36..

sensixx B2

(*) Model dependent

You can download this manual from the local homepages of Bosch



General safety warnings

• Danger of electric shocks or fire!

• This appliance is to be connected and used in accordance with

the information stated on its characteristics plate.

• This appliance must be connected to an earthed socket. If

it is absolutely necessary to use an extension cable, make
sure that it is suitable for 16A and has a socket with an earth
connection.

• The iron should not be used if it has been dropped, if there

are visible signs of damage or if it is leaking water. It must be
checked by an authorized Technical Service Centre before it
can be used again.

• Do not allow the power cable to come into contact with the

soleplate when it is hot.

• In order to avoid that, under unfavourable mains conditions,

phenomena like transient voltage drops or lighting fluctuations
can happen, it is recommended that the iron is connected to a
power supply system with a maximum impedance of 0.27Ω . If
necessary, the user can ask the public power supply company
for the system impedance at the interface point.

• This appliance is not intended to be used by persons (including

children) with reduced physical, sensory or mental capacities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance
by a person responsible for their safety.

• Keep the appliance out of children’s reach.

• Children should be supervised to ensure that they do not play

with the appliance.

• Remove the plug from the socket before filling the appliance with

water or before pouring out the remaining water after use.

• The appliance must be used and placed on a stable surface.

• When placed on its stand, make sure that the surface on which

the stand is placed is stable.

• The iron must not be left unattended while it is connected to

the supply mains.

• Unplug the appliance from the mains supply after each use, or

if a fault is suspected.

• The electrical plug must not be removed from the socket by

pulling the cable.

• Never immerse the iron in water or any other fluid.

• Do not leave the appliance exposed to weather conditions (rain,

sun, frost, etc.)

• With the aim of avoiding dangerous situations, any work or

repair that the appliance may need, e.g. replacing a faulty mains
cable, must only be carried out by qualified personnel from an
Authorised Technical Service Centre.

Using Your Iron

1. Your iron

max.

A. Shot of steam

N. Auto shut off

indicator lamp (*)

M.Power
cable

J. Max. Water

F. Water tank

E. Spray

outlet

C. Steam regulator

G. Soleplate

B. Spray button

I. Temperature control

L. Water tank

cover

K. Pilot lamp

H. Temperature control pointer

* Model dependent

D. Steam regulator

pointer

2. Filling the water tank

Set the steam regulator (C) to the «0» position and

unplug the iron from the mains!

Use only clean water from the tap and do not mix anything with
it. The addition of other liquids, such as perfume, will damage
the appliance.

Do not use condensation water from tumble dryers, air conditioners
or similar appliances. This appliance has been designed to use
normal tap water.

To prolong the optimum steam function it is possible to mix tap
water with distilled water 1:1. If the tap water in your district is
very hard, mix tap water with distilled water 1:2.

You can inquire about the water hardness with your local water
supplier

To prevent spillage of water out of the appliance in vertical position,

never fill beyond the «max» water level mark!

7. Ironing without steam

This function enables the iron to be used for dry ironing.

1. Set the steam regulator (C) to the «0» position.

2. Select an appropriate temperature for the type of material being
ironed.

8. Spray

This can be used to remove stubborn wrinkles.

1. Do not use the spray function with silk as staining may occur.

2. Make sure that there is water in the tank (F).

3. When ironing, press the spray button (B) and water will spray
out of the spray outlet (E) onto the garment.

9. After finishing each ironing session

1. Unplug the iron from the mains socket.

2. Set the steam regulator (C) to the «0» position.

3. Open the water tank cover (L).

4. Hold the iron with the point facing up and shake it gently until
all the water has come out.

5. Set the iron aside in a vertical position to cool down.

6. Coil the power cable (M) loosely around the heel of the iron,
before storing.

7. Store the iron in an upright position.

10. Multiple de-scaling system

This range of irons is equipped with the following de-scaling
features “AntiCalc”.

A. self-clean

Each time you use the steam regulator (C), the “self-clean” system
cleans the mechanism of any scale deposits.

B. calc’n clean

The “calc‘n clean” function helps to remove scale particles out
of the steam chamber. Use this function approximately every 2
weeks, if the water in your area is very hard.

Fill the water tank, set the temperature dial (I) to the “max”. position
and plug in the iron.

After the necessary warm-up period, unplug the iron and hold
it over a sink. Take out the steam regulator (C) by turning it to
the position while pressing it down. Gently shake the iron.
Boiling water and steam will come out, carrying scale or deposits
that might be there. When the iron stops dripping, reassemble
the steam regulator in reverse order and move it to the «0»
position. Heat up the iron again until the remaining water has
evaporated.

If the steam regulator needle is soiled, remove any deposits from
the needle tip with vinegar and rinse off with clean water.

C. anti-calc cartridge (model dependent)

The anti-calc cartridge has been designed to reduce the build-up
of scale produced during steam ironing, helping to extend the
useful life of your iron. Nevertheless, the “anti-calc” cartridge cannot
remove all of the scale that is produced naturally over time.

11. Anti-drip system

All the irons in this range are equipped with an anti-drip system.
This will automatically stop the iron producing steam when the

selected temperature setting is too low to prevent water from
dripping out of the soleplate. You may hear a clicking sound when
this system is in operation.

Additional Features (Model Dependent)

Auto shut-off

Some irons in this range are equipped with an auto-shut off
system.

The “secure” auto shut-off function switches off the iron
automatically when it is not being used, thus helping to prevent
accidents and saving energy. When the appliance is first plugged
in, this function will be inactive for the first 2 minutes to allow it to
reach the set temperature.

If during ironing, the iron is not moved for a certain length of time,
the iron will automatically switch off. The length of time will depend
on the position the iron has been left in:

Horizontally (flat) or on its side: 30 seconds
Vertically (upright): 8 minutes

The pilot light on the top of the handle (N) will flash when auto
shut-off has been activated. To switch the iron back on, move it
gently from side to side. The light will stop flashing.

Fabric-protection soleplate cover

The fabric-protection cover is used for steam-ironing delicate
garments at maximum temperature without damaging them.

Use of the protector also does away with the need for a cloth to
prevent shine on dark materials.

It is advisable to first iron a small section on the inside of the
garment to see if it is suitable.

To attach the fabric protector to the iron, place the tip of the iron
into the tip of the fabric protector and press the rear of the protector
upward until you hear a click. To release the fabric protector, pull
down on the clip at the rear and remove from the iron.

The protective cover can be purchased from After-sales.

Accessory code

(After-sales)

650808

4. Ironing with steam

The steam regulator (C) is used to adjust the amount of
steam produced when ironing.

1. Make sure that there is water in the tank (F).

2. Adjust the temperature setting and then set the steam regulator,
by lining it up with the pointer (D), according to the table below.
Steam will automatically be produced:

Temperature Setting Steam Regulator Setting

••• to “max” 2

•• 1

3. You can get extra steam by pressing and holding the steam
regulator (C) for a maximum of 2 seconds.

Note: At a temperature setting of “•”, the soleplate is not hot enough

to produce steam so the steam regulator should be set to the «0»
position to avoid water dripping from the soleplate (G).

5. Ironing with shot of steam

This can be used to remove stubborn wrinkles or to press
in a sharp crease or pleat. It cannot be used on a synthetic
setting for delicate items.

1. Set the temperature control (I) to the “•••” or “max” position.

2. Set the steam regulator (C) to the «2» position.

3. Press the shot of steam (A) button on the handle repeatedly at
intervals of 5 seconds.

6. Vertical steaming with shot of steam

This can be used to remove creases from hanging clothes,
curtains etc. It cannot be used on a synthetic setting for
delicate items.

WARNING! Do not use vertical steam while the item is being

worn. Never spray or aim steam at people or animals!

1. Make sure that there is water in the tank (F).

2. Set the temperature control (I) to the «•••» or «max» position

and the steam regulator (C) to the «2» position.

3. Hold the iron in an upright position about 15 cm away from the
garment being steamed.

4. Press the shot of steam button (A) on the handle at intervals of
5 seconds, however, after 4 jets of steam, wait for 10seconds
to allow for continued steam production.

3. Setting the temperature

The temperature control (I) adjusts the temperature of the
soleplate (G).

1. Check the temperature instructions shown on the care label
of the garment you are ironing and set the temperature
control (I) to the corresponding position by lining it up with
the pointer (H) on the iron:

Fabric Temperature Setting

Synthetics •

Silk - Wool ••

Cotton - Linen •••





2. If you are unsure what type of material the garment is made from,
start ironing on the lowest temperature setting and increase
accordingly. If the garment is made from mixed fabrics, set the
temperature for the most delicate material.

3. For silk, woollen or synthetic materials iron the reverse side
of the fabric to prevent shiny patches. Avoid using the spray
function to prevent stains.

4. Sort your garments based on their care labels, always
starting with clothes that have to be ironed at the lowest
temperature.

5. The pilot lamp (K) will stay lit while the iron is heating up and go
out once the selected temperature has been reached. Wait a
few seconds after the lamp goes out before you start ironing.

Once the iron is ready, you can continue to iron even if the pilot

lamp comes on again.

6. If your iron has auto shut-off and the lamp on the top of the
handle (N) is flashing, the auto shut-off has activated. Gently
move the iron side to side to restart it.

Tips to help you save energy

Steam production consumes the most energy. To help minimise
the energy used, follow the advice below:

• Start by ironing the fabrics that require the lowest ironing

temperature.

• Regulate the steam according to the selected ironing

temperature.

• Only use steam if necessary. If possible, use the spray

function instead.

• Try to Iron the fabrics while they are still damp and reduce the

steam setting. Steam will be generated from the fabrics rather
than the iron. If you tumble dry your fabrics before ironing

them, set the tumble drier to the ‘iron dry’ programme.

• If the fabrics are damp enough, turn off the steam regulator

completely.

• Stand the iron upright during pauses. Resting it horizontally

with the steam regulator on generates wasted steam.