Bosch IPP-AL400-ULKT2, IPP-AL400-ULKT1 Specsheet

Intrusion Alarm Systems | IPP‑AL400‑ULPS Power Supplies (4.0 A)

IPP‑AL400‑ULPS Power Supplies (4.0 A)

www.boschsecurity.com

u Filtered and electronically regulated outputs

u Short circuit and thermal overload protection

u Built‑in charger

The IPP‑AL400‑ULPS is a switching power supply and
charger. It converts 115 VAC, 50 Hz to 60 Hz input into
single 12 VDC or 24 VDC Class 2 Rated power‑limited
output.

Functions

Supervision Monitoring

The IPP‑AL400‑ULPS Power Supply monitors three
independent outputs for the following failure
conditions:

• AC failure

• Low battery

• Battery presence

Certifications and approvals

Either Bosch Security Systems, Inc. or Altronix® holds
the following Listings and Approvals:

Region

Certification

USA UL Bosch Security Systems, Inc. -

AMCX.S1871, Central Station Alarm
Units; AOTX.S1871, Local Alarm Units;
APAW.S1871, Police Station-connected
Alarm Units; APOU.S1871, Proprietary
Alarm Units; NBSX.S1871, Household
Burglar Alarm System Units;
UOXX.S5579, Control Unit Accessories,

u Automatically switches to standby battery when AC

fails

u Three supervision outputs

Region Certification

System; UTOU.S1871, Control Units
and Accessories, Household System
Type

UL Altronix Corporation - ALVY: Access Con-

trol System Units (ANSI/UL294), APHV:
Power Supplies for Use with Burglar­Alarm Systems (ANSI/UL603), NBRZ:
Hospital Signaling and Nurse Call Equip­ment (ANSI/UL1069), and UTRZ: Power
Supplies for Fire-Protective Signaling
Systems (UL1481)

CSFM 7300-1615: 226 7300 -- FIRE ALARM

CONTROL UNIT ACCESSORIES/MISC.
DEVICES

Installation/configuration notes

Compatibility Information

The IPP‑AL400‑ULPS is compatible with any device
requiring 12 VDC or 24 VDC. The ULPS enclosure and
the following modules have been listed for use
together:

• IPP‑AL400‑ULPS Power Supply

• IPP‑PD4‑ULCB Power Distribution Module

• C900V2 Dialer Capture Module

• D9210C Access Control Interface Module

• B426 Ethernet Communication Module

2 | IPP‑AL400‑ULPS Power Supplies (4.0 A)

Mounting Considerations

The IPP‑AL400‑ULPS enclosure has two three‑hole
mounting patterns. The mounting pattern will support
any one of the following combinations:

• Two B426 Ethernet Communication Modules

• Two D9210C Access Control Interface Modules

• One B426 and one D9210C

The enclosure also supports up to two Conettix IP
C900V2 Dialer Capture Modules and one
IPP‑PD4‑ULCB Power Distribution Module.

Technical specifications

Electrical

Power Input

Voltage: 115 VAC, 50 Hz to 60 Hz

Current: 1.45 A

Input Fuse: 3.5 A, 250 V

Short circuit and thermal overload
protection

Power Output

Voltage: 12 VDC or 24 VDC, selectable

Current: 12 VDC at 4 A

24 VDC at 3 A

IPP-AL400-ULPS Power Supply Kit 2

Includes one power supply, one enclosure, one IPP­PD4-ULCB Power Distribution Module, and one B426
Ethernet Communication Module.
.

Order number IPP-AL400-ULKT2

Class: Class 2 Rated power limited

Battery Power

Maximum Charge
Current Output:

Type: Sealed lead‑acid or gel‑type batteries

7 A

Mechancial

Enclosure Dimensions: 51.8 cm x 41.3 cm x 10.2 cm

Material: Red steel, 1.2 mm thick

Supervision Outputs: Three

(20.375 in. x 16.25 in. x 4 in.)

• AC Failure (Form C contacts)

• Low Battery(Form C Contacts)

• Battery Presence (Form C Contact)

Trademarks

Altronix® is a registered trademark of Altronix Corp.

Ordering information

IPP-AL400-ULPS Power Supply

Includes one power supply and one enclosure.

Order number IPP-AL400-ULPS

IPP-AL400-ULPS Power Supply Kit 1

Includes one power supply, one enclosure, and one
IPP-PD4-ULCB Power Distribution Module.

Order number IPP-AL400-ULKT1