Bosch FMR-DACT-KEYPAD Installation Manual

FMR-DACT-KEYPAD

Operation Instructions

EN

DACT Keypad
Programmer

FMR-DACT-KEYPAD | Operation Instructions | 1.0 Description

Notices

Follow these instructions to avoid personal injury and damage to the equipment.

Install, test, and maintain the FMR-DACT-KEYPAD according to these instructions, NFPA 72, local
codes, and the Authority Having Jurisdiction (AHJ). Bosch is not responsible for improperly installed,
tested, or maintained devices.

1.0 Description

The FMR-DACT-KEYPAD (Figure 1) is a four-wire alphanumeric liquid crystal display (LCD) keypad used as a
programming device for the DS9602, D9068, and FPT-DACT Fire Communicators.

Figure 1: FMR-DACT-KEYPAD

2 Bosch Security Systems, Inc. | 8/06 | F01U002307C

FMR-DACT-KEYPAD | Operation Instructions | 2.0 Wiring

.

2.0 Wiring

Ensure all wiring is de-energized before routing.

1. Route the wiring from the DACT to the FMR-DACT-KEYPAD.

2. Pull the base wiring through the wire entrance in the FMR-DACT-KEYPAD base.

3. Connect the wiring to the FMR-DACT-KEYPAD terminal strip as shown in Figure 2.

4. Place the FMR-DACT-KEYPAD on its base.

5. While feeding the excess wiring out of the back of the base, press straight down on the cover until it latches

on.

Figure 2: Wiring the FMR-DACT-KEYPAD Terminal Strip

LINE 1

1

2

+12 VDC
Com

Data In
Data Out

1 - DACT Fire Communicator
2 - FMR-DACT-KEYPAD Terminal Strip
3 - +12 VDC (red wire)
4 - Common (black wire)

LINE 2

SYS TROUBLE

HEARTBEAT

++- -AB

12345

KEYPAD

NC C NO

7

3

4

5

6

5 - Data in (green wire)
6 - Data out (yellow wire)
7 - Keypad terminals

Bosch Security Systems, Inc. | 8/06 | F01U002307C 3

FMR-DACT-KEYPAD | Operation Instructions | 3.0 Power Up

3.0 Power Up

The power supplied to the FMR-DACT-KEYPAD
from the DACT is 12 VDC with a maximum draw
of 100 mA.

4.0 Installing the Instruction
Label and Slide

1. Place the instruction label (Item 2 in Figure 3) on

the pullout slide (Item 3 in Figure 3), positioning
it as close to the pull tab as possible.

2. Install the slide so you can pull from the left or

right from the back of the base.

Figure 3: Installing the Instruction Label and

Slide

1

5.0 Setting the Address

The FMR-DACT-KEYPAD must have an address
set within its address pins.

Select the address, 1 to 15, by placing the shorting
jumpers over the address pins as shown in Figure 4.

Figure 4: Setting the Address

Address 1

1 | 2 | 4 | 8

Address 4

1 | 2 | 4 | 8

Address 7

1 | 2 | 4 | 8

Address 10

1 | 2 | 4 | 8

Address 13

1 | 2 | 4 | 8

Address 2

1 | 2 | 4 | 8

Address 5

1 | 2 | 4 | 8

Address 8

1 | 2 | 4 | 8

Address 11

1 | 2 | 4 | 8

Address 14

1 | 2 | 4 | 8

Address 3

1 | 2 | 4 | 8

Address 6

1 | 2 | 4 | 8

Address 9

1 | 2 | 4 | 8

Address 12

1 | 2 | 4 | 8

Address 15

1 | 2 | 4 | 8

2

3

2

1 - Back of the FMR-DACT-KEYPAD
2 - Label
3 - Slide
Note: The label on the slide has writing on the

reverse side.

4 Bosch Security Systems, Inc. | 8/06 | F01U002307C

FMR-DACT-KEYPAD | Operation Instructions | 6.0 Operating the Keypad

.

6.0 Operating the Keypad

While installing the FMR-DACT-KEYPAD,
the system does not monitor the input

6.1 FMR-DACT-KEYPAD

The FMR-DACT-KEYPAD (Figure 5) is an
alphanumeric LCD keypad used for programming

Figure 5: FMR-DACT KEYPAD

points.

and debugging only while it is connected to the
DACT. This keypad has a two-line, 16-character
display showing information on various DACT
programming functions. In most cases, the first line
contains general system status information; the
second line describes the specific programming
menus and prompts.

Figure 6 on page 6 identifies and describes the FMR­DACT-KEYPAD keys.

1
2

3

4

5

6

7

PROGRAMMER

14

13

12

DACT

SYSTEM NORMAL
0: PROGRAM

1 23

456
789

#

Clear

*

0

Program

11

Command

10

Silence

Reset

Drill

Disable

Test

History

9

8

1 - First line of display.
2 - Second line of display.
3 - [Reset] key:

Figure 6 on page 6 For more information, refer to the D9068 (P/N: 45386), DS9602 (P/N: 45387) and FPT-DACT

Operation & Installation Guide (P/N: F01U002505).

4 - [Drill] key:
5 - [Disable] key:

Initiates a manual reset of the DACT. Clears the character selected by the cursor. Refer to

Advances to the next programmable feature or character position (Figure 6).

Returns to the previous programmable feature or character position (Figure 6).

6 - [Test] key: Enters Test Mode. Pressing [Test] when entering a telephone number accesses three telephone

control code options. Refer to

Guide (P/N: F01U002505)

7 - [History] key:

Enters History Mode. Refer to the D9068 (P/N: 45386), DS9602 (P/N: 45387), or FPT-DACT Operation

the D9068 (P/N: 45386), DS9602 (P/N: 45387), or FPT-DACT Operation & Installation

& Installation Guide (P/N: F01U002505).

8 - [3] key: Increases the FMR-DACT-KEYPAD backlight intensity. Press and hold [* Clear] first. Then press [3] to

adjust the intensity.

9 - [6] key: Decreases the FMR-DACT-KEYPAD backlight intensity. Press and hold [* Clear] first, then press [6] to

adjust the intensity.

10 - [# Command] key: Accepts programming entries into FPT-DACT. Press this key after every programming entry.
11 - [0 Program] key: Enters the Programming Mode menu. Refer to the D9068 (P/N: 45386), DS9602 (P/N: 45387), or

FPT-DACT Operation & Installation Guide (P/N: F01U002505) for programming instructions.

12 - [* Clear] key: Cancels any programming menu without making changes. Return to the message SYSTEM

NORMAL by pressing [* Clear] until SYSTEM NORMAL appears across the first line.

13 - [4] key: Decreases FMR-DACT-KEYPAD sounder volume. Press and hold [* Clear] first, then press [4] to adjust

the volume.

14 - [1] key: Increases FMR-DACT-KEYPAD sounder volume. Press and hold [* Clear] first, then press [1] to adjust

the volume.

Bosch Security Systems, Inc. | 8/06 | F01U002307C 5

FMR-DACT-KEYPAD | Operation Instructions | 7.0 Programming the FPT-DACT with the FMR-DACT-KEYPAD

Figure 6: Additional Functions of the [Drill], [Disable], and [Reset] Keys

1

2

3

PHN NMBR 1: 5551
234????????????

PHN NMBR 1: 5551
234????????????

PHN NMBR 1: 5551
234????????????

Drill

Disable

Reset

PHN NMBR 1: 5551
234????????????

PHN NMBR 1: 5551
234????????????

PHN NMBR 1: 5?51
234????????????

1 - Press [Drill] to move the cursor to the next position
2 - Press [Disable] to move the cursor back one position
3 - Press [Reset] to clear the character that is currently selected

7.0 Programming the FPT-DACT with the FMR-DACT-KEYPAD

Only use the FMR-DACT-KEYPAD to program and debug.

1. Program the DS9602, D9068, and FPT-DACT according to the D9068 (P/N: 45386), DS9602 (P/N: 45387), or

FPT-DACT Operation and Installation Guide (P/N: F01U002505).

2. If there is no FMR-DACT-KEYPAD activity for 3 min, it disables. The FMR-DACT-KEYPAD buzzer sounds

and a System Fault message appears.

3. Disconnect the FMR-DACT-KEYPAD from the DACT as described in the D9068 (P/N: 45386), DS9602

(P/N: 45387), or FPT-DACT Operation and Installation Guide (P/N: F01U002505).

8.0 Troubleshooting

Table 1: Troubleshooting

FMR-DACT-KEYPAD Status Cause Corrective Action

The sounder is heard
continuously and a System
Fault message appears.

The FMR-DACT-KEYPAD
does not respond to input.

Three-beep error tone sounds
at all FMR-DACT-KEYPADs.

• The yellow and green ground wires are disconnected.

• The FMR-DACT-KEYPAD was not correctly

Replace the DS9602,
D9068, or FPT-DACT.

programmed at the DACT.

• The DACT malfunctioned.

The address is not set. Set the address.

An incorrect key was pressed. Press the correct key.

6 Bosch Security Systems, Inc. | 8/06 | F01U002307C

.

9.0 Specifications

Table 2: Specifications

Nominal Supply Voltage
Standby Current
Alarm Current
Operating Temperature
Relative Humidity
Dimensions (H x W x D)
Listings and Approvals
Environmental

12 VDC
100 mA; 75 mA for battery calculation
100 mA; 75 mA for battery calculation
+32°F to +120°F (0°C to +49°C)
5% to 85%, non-condensing (+86°F, +30°C)
5 in. x 6 in x 1 in. (12 cm x 16 cm x 3 cm)
UL864, California State Fire Marshall (CSFM)
Use indoor, dry

FMR-DACT-KEYPAD | Operation Instructions | 9.0 Specifications

Bosch Security Systems, Inc. | 8/06 | F01U002307C 7

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450-9199
Customer Service: [phone]
Technical Support: [phone]

© 2006 Bosch Security Systems, Inc.
F01U002307C