Bosch FMM462 User Manual

Fire Alarm Systems | FMM‑462 Series POPIT Addressable Manual Stations

FMM‑462 Series POPIT Addressable
Manual Stations

www.boschsecurity.com

u Single‑gang mounting

u Latching alarm lever and key‑locked reset

u Rugged die‑cast housing with 14 gauge (1.9 mm)

plated steel back and corrosion‑resistant
construction

u Optional scored acrylic breakrod

The FMM‑462 Series Addressable Manual Stations
allow people evacuating a building to initiate an alarm
and alert others still inside. This UL-listed initiating
device is compatible with the Bosch Security Systems,
Inc. G Series Control Panels and the D9124 Fire Alarm
Control Panel (FACP).
The POPIT module is addressed using on-board slide
switches. It is then connected to a D9124 data
expansion loop. The POPIT is polled by the control
panel and sends reports on any opens, shorts, or
ground faults on the manual station's wiring. The
addressable feature allows the agencies responding to
alarm or trouble conditions to go to the point that
initiated the alarm or trouble report.
These low-profile manual stations are die cast with
rounded edges to fit most design applications. All
metallic components are painted or plated to inhibit
corrosion. The FMM‑462 Series Manual Stations
conform with the Americans with Disabilities Act
(ADA) standards.

Functions

Addressable Operation

The POPIT connects to a two‑wire data expansion
circuit from the control panel. Device address is set
through slide switches on the POPIT Module, allowing
programmable device identification by the control
panel.

Certifications and Approvals

ADA Complies with Americans with

Disabilities Act ADA 4.28.3

NFPA Complies with National Fire

Protection Association NFPA 72

Region Certification

USA UL UNIU: Boxes, Non-Coded (UL38)

CSFM 7150-1615:0122

2 | FMM‑462 Series POPIT Addressable Manual Stations

Installation/Configuration Notes

Compatibility Information

The FMM‑462 Series Addressable Manual Stations are
compatible with the following products:

Category Product ID Product Description

Control D7212G Control panel

Panels: D7412G Control panel

D9412G Control panel

D9124 Addressable FACP

Modules D9127U POPIT module

Mounting Considerations

The FMM‑462 manual stations are for indoor use only.
The FMM‑462 or FMM‑462‑D and the wiring from the
control panel data expansion loop fit into a single-gang
back box for flush mounting. Use the larger
FMM‑100BB‑R Back Box for surface mounting and to
provide additional room for system wiring and the
module.

Parts Included

Quant. Component

1 Manual station

1 D9127U POPIT module

1 FMM‑100GR scored acrylic breakrod

1 D102 Key (1358)

1 Literature pack

Ordering Information

FMM‑462 Single‑Action Manual Station

A UL-listed initiating device compatible with the Bosch
Security Systems, Inc. G Series Control Panels and the
D9124 Fire Alarm Control Panel (FACP)

Order number FMM-462

FMM‑462‑D Double‑Action Manual Station

A UL-listed initiating device compatible with the Bosch
Security Systems, Inc. G Series Control Panels and the
D9124 Fire Alarm Control Panel (FACP)

Order number FMM-462-D

Accessories

D102 Replacement Key

Replacement key (#1358) for the D101 lock.

Order number D102

FMM‑100BB‑R Surface‑mount Back Box (red)

Red cast‑metal back box

Order number FMM-100BB-R

FMM‑100GR Scored Acrylic Break Rods

Scored acrylic rods (12 per package)

Order number FMM-100GR

Technical Specifications

Environmental Considerations

Temperature (operating): +14°F to +120°F (-10°C to +49°C)

Mechanical Properties

Activation Force: 5 lb (2.3 kg)

Alarm Response Time: 1 sec (approximately)

Dimensions (HxWxD): 4.75 in. x 3.2 in. x 0.875 in.

Material: Painted die‑cast metal, plated steel back

(12.1 cm x 8.1 cm x 2.2 cm)

and painted steel front

Power Requirements

Current (alarm): 0.8 mA

Current (normal): 0.5 mA

Voltage (operating): 7 VDC to 15 VDC supplied by the control

panel