Bosch DS820IT, DS820I User Manual

Pet Immune Area

Installation Instructions

Don't point where pets can climb.

DS820i/DS820iT Series

TriTech PIR/Microwave Intrusion Detectors with Pet Immunity

1.0 Description

The DS820i and DS820iT Series are high performance TriTech Passive Infrared (PIR)/Microwave (MW) Intrusion Detectors which use advanced signal processing to provide outstanding catch performance and unsurpassed false alarm immunity. They are designed to detect movement of a human body in the interior of a structure as it moves across the Detector’s field of view. When motion is detected, the Detector sends an alarm signal to the control panel. With Bosch Security Systems Pet Friendly numerous rodents or flying birds. This pet immunity feature has not been tested by Underwriters Laboratories.

2.0 Specifications

• Input Power: 6 to 15 VDC, 16 mA nominal standby (up to 35 mA

during walk testing and alarm). Use only Limited Power Source up to 5 A maximum.

• Standby Power: No internal standby battery.

installations, 4 hours (64 mAh) standby power must be provided

power supply.

• Alarm Relay: Silent operating Normally Closed reed relay. Contacts rated 3 W, 125 mA, 28 VDC maximum for DC resistive loads; and protected by a 4.7 Ω, 1/2 W resistor in the common “C” leg of the relay. Do not use with capacitive or inductive loads.

• Temperature: The storage and operating temperature range is

-40°F to +120°F (-40°C to +49°C).

installations, the temperature range is +32°F to +120°F (0°C to +49°C).

3.0 Installation

3.1 Remove the cover using

a small flat-blade screwdriver.

pet immunity, these Detectors will not detect a dog up to 100 pounds (45 kg) or two 60 pound (27 kg) dogs, up to 10 cats,

• Microwave Frequency:

DS820i/820iT: 10.525 GHz (UL Listed) DS820iTA: 10.687 GHz (Export only, not UL Listed)

DS820iTB: 9.9 GHz (Export only, not UL Listed)

For UL Certificated

by the control unit or by a Listed burglary

For UL Certificated

3.2 Press the vertical adjust tab

toward the side of the base and lift out the board.

• Coverage: 20 ft. by 20 ft. (6 m by 6 m)

• Tamper: (“T” models only) Normally Closed (with cover on). Contacts rated at 28 VDC, 125 mA max. Connect tamper circuit to a 24-hour protection circuit.

• Options: B335 Low Profile Swivel Mount Bracket , B338 Ceiling Mount Bracket. (The use of brackets is not recommended for pet applications and may reduce range and increase dead zone areas).

• Patents: This product is covered by one or more of the following U.S. patents: #4,660,024, #4,764,755, #5,077,548, #5,208,567, #5,262,783, #5,450,062, and #5,670,943.Other patents pending.

3.3 Select a mounting location. Mount the sensor where an intruder will most likely cross through the coverage pattern.

LED ON

3.4 Avoid:

Mounting Outdoors

Windows

and

Uninsulated

Walls

Optional anti-tamper screws at each end

Insert screwdriver here or here

Direct Sunlight

Direct Hot or Cold Drafts

Moving Objects

Bottom of Detector

7.5-9ft

3.5 Observe the Pet Immunity mounting recommendations.

NOTE: The upper areas are

not pet immune.

7.5 -9 ft.

(2.3 - 2.7 m)

Heat Sources

Air Conditioning Outlets

Mount the detector 7.5 to 9 feet

(2.3 to 2.7 meters) above the floo

LED ON

7.5-9ft

3.5 Mount the detector.

Meters

NOTE: To avoid possible circuit board damage, use only the mounting hardware provided in the

appropriate punch-out mounting holes.

Thinwall knockouts

for wiring

Corner Mount

Surface

Mount

Don't overtighte n the mounting screws

Cover may not att ach correctly

7.5 - 9 ft.

(2.3 - 2.7 m)

Remove

Areas

if using the

B335 Bracket

Do not use

the B335

Bracket in

pet

applications

3.6 Wire the detector.

Alarm

Contacts

(DS820iT

only)

6-15 VDC

Tamper

Contacts

LED

Normally Clos ed co ntacts

NOTE: Use only Limited Power Source

up to 5 A maximum.

3.7 Snap the board into the base so the notch aligns with the tab.

3.8 Select LED operation.

LED ON

3.9 In non-pet applications only, if

look-down is desired, peel away the look-down mask. Do not

remove the clear plastic lens.

3.10 Microwave range is pre-set. Field

adjustment is not required.

NOTE: If you choose to adjust the range, set

the adjustment as low as possible for proper catch performance. Be sure to walk test throughout the coverage pattern after any adjustment.

INCREASE

Do not use excessive force when adjusting the microwave

7.5-9ft

OFF

LED ON

7.5-9ft

Peel away

the mask

pot.

3.11 Walk test the detector. Perform this test at the time of installation and annually thereafter.

Green = PIR detect Yellow = MW detect

Red = Alarm

Microwave Coverage

PIR Coverage

This detector contains an environmental stabilization circuit which requires approximately 2 minutes after initial power-up to warm up. During this time the detector will not respond to any movement.

Please wait 2 minutes after initial power-up

to perform any walk tests.

5.0 FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference, including interference that may cause undesired operation.

Changes or modifications not expressly approved by Bosch Security Systems can void the user’s authority to operate the equipment.

Bosch Security Systems Fairport, New York, USA 14450-9199 Customer Service: (800) 289-0096; Technical Support: (888) 886-6189

4.0 Coverage Patterns

Meters

Look Down

Feet

6777

5666

45-5534-

Microwave Coverage

PIR Coverage

1234567891011

Although generally not required, the lens diagram shows the appropriate areas to be masked. Use an opaque material (such as, electrical tape) to

12 22 23 33 34 44 45 55 56 66

67 77

mask the desired areas.

DS820i Lens

200Feet

(inside view)

DS820i/DS820iT Series Installation Instructions

P/N: 38055K 12/03 Page 2

2333

1222

LED ON

7.5-9ft

111

310