Bosch D130 User Manual

1 | Overview

The D130 Auxiliary Relay Module is an accessory for use with
Bosch Security Systems, Inc. control panels. (For additional
information, refer to your control panel documentation.)
This module has a 12 V/24 V relay with two sets of non­latching Form C contacts. The D130 allows the system to
switch larger amounts of current or different voltages that
are beyond the control panel’s auxiliary power rating, or the
rating of modules such as the D8129 Octo-relay Module or
the B308 Octo-output Module.
Use the D130 with a D125B Dual Class B Initiating Mod­ule and a 24 VDC power supply to interrupt power to 24 V
smoke detectors with the Sensor Reset function at a keypad.

Armt

NO COM NEGNC

NO

COMNC12 V

24 V

E1

CUT FOR 24 V COIL

Figure 1.1: D130

The D130 uses a 12 V or 24 V power source to power its coil.
The relay can be energized by switching the 12/24 V or the
NEG side of the relay coil. When the contacts are in the inactive
state, the normally closed (NC) terminal has continuity with the
common (COM) terminal. In the active state, the normally open
(NO) terminal has continuity with the COM terminal. A red LED
indicates the coil of the relay is energized.

Auxiliary

Relay Module overview

2 | Mount the module

Mount the module into the enclosure’s 3-hole mounting
pattern using the supplied mounting screws and mounting
bracket. Refer to Figure 2.1.

Mounting the module:

1. Using the two supplied #4 screws, attach the D130 to
the supplied three-hole mounting bracket.

2. Align the mounting bracket and module.

3. Using the three supplied #8 screws, secure the mounting
bracket and module through either side of the control

panel enclosure.

2

1

3

4

E1

CU R 24 V C

Arm t

2

Figure 2.1: Mounting the D130

F01I011616

>ABS/PC<

6

5

Callout ― Description

1 ― Module

2 ― #4 screw

3 ― Mounting bracket

4 ― Control panel enclosure wall

5 ― Mounting locations

6 ― #8 screw holes for mounting to enclosure inside wall

3 | Wire the module

Wire the module to the control panel and other devices using
the fi gures in this section.

NOTICE!

For system supervision, do not use looped wire
under the terminals. Break the wire run to provide
supervision of the connections.

NOTICE!

Run all non-power limited wiring at least 0.25 in
(0.64 cm) from power limited wiring.

3.1 | Wire for switched auxiliary power devices

7

POS+NEG

-

2

NO COM NC NEG

1

12 V NC COM NO

24 V

1

E1

6

Figure 3.1: Wiring a D130 with 12 VDC or 24 VDC power
supply for switched auxiliary power devices

Callout ― Description

1 ― Power limited, supervised

2 ― D130 module

3 ― Control panel

4 ― 12 VDC* switched AUX power terminal

5 ― COM terminal (of the control panel)

6 ― Jumper E1 not cut*

7 ― External 12 VDC or 24 VDC power supply**

8 ― Device requiring 12 VDC or 24 VDC switched auxiliary
power

* If power output is 24 VDC, cut Jumper E1.
** When using ground fault detect, do not reference the
external power supply negative terminal to earth ground.

8

POS+NEG

3

-

4

5

3.2 | Wire with a D125B Dual Class B
Inititating Module

NOTICE!

To supervise the loops, install an end-of-line (EOL)
resistor beyond the last detector of each protective
loop. If you are replacing a D125 or D125A module

with the D125B, you can use the 1.5 k
installed with the original system. If you are installing
a D125B in a new system, or in an existing system

and adding additional devices, use the 1.8 k
resistor (P/N: 15-03130-006) supplied with the
module.

Ω resistor

Ω

NOTICE!

Refer to the D125B Installation Instructions (P/N:
F01U036340) for more information.

5

TB1/J1

1

ZONE

SWITCH

4

POS+NEG

-

9

2

NO COM NC NEG

E1

6

R8

3

4 5

2

ZONE

PANEL

A

COMMON

B

7

8

12 V NC COM NO

24 V

RV1

RV4

LOOP

1

1

RV3

8

7

6

B+

A-

B-

LOOP

LOOP

LOOP

RV2

9

10

A+

EARTH

GND

3

10

11

Figure 3.2: Wiring a D130 with 12 VDC or 24 VDC power
supply and a D125B

Callout ― Description

1 ― Power limited, supervised

2 ― D130 module

3 ― Control panel

4 ― External UL Listed 12 VDC or 24 VDC regulated power
supply*

5 ― D125B Dual Class A Initiating Module

6 ― Jumper E1 not cut**

7 ― To on-board point or expansion module***

8 ― Connect only to one common at the control panel

9 ― To additional D125B Dual Class A Initiating Module

10 ― 12 VDC** switched Aux power terminal

11 ― COM Terminal

* When using ground fault detect, do not reference the
external power supply negative terminal to earth ground.
** If power output is 24 VDC, cut Jumper E1.
*** A D8128D OctoPOPIT Module or a B208 Octo-input
Module can be used.

3.3 |

Wire with a D125B

Dual Class B Inititating Module

and a D8129 Octo-relay Module

4 | Certifi cations

NOTICE!

Refer to the D125B Installation Instructions (P/N: F01U036340) for more information.

After any programming or hardware change, perform a functional test of the system as required by local codes.

5

POS+NEG

-

10

3

NO COM NC NEG

12 V NC COM NO

24 V

E1

11

6

TB1/J1

SWITCH

4

ZONEX OUT 1

ZONEX OUT 2

Aux Power +

COM

1

ZONE

RV1

RV4

LOOP

1

2

RV3

6

7

8

B-

A-

B+

LOOP

LOOP

LOOP

NC

RV2

10

9

EARTH

A+

GND

DATA
AUX
GND

COMMNCNO

COMM

2

1

7

NO

COMMNCNO

COMMNCNO

COMMNCNO

COMMNCNO

COMMNCNO

COMMNCNO

8

7

6

5

4

3

R8

2

4 5

3

PANEL

ZONE

B

COMMON

A

8

9

1

1

2

Figure 3.2: Wiring a D130 with 12 VDC or 24 VDC power supply and the D125B and an expansion module

Callout ― Description

1 ― Power limited

2 ― Supervised

3 ― D130 module

4 ― Control panel* (ZONEX 2 available on D9412GV4/D9412GV3/D9412GV2/D9412G/D9412/D9112/D9112B1 only)

5 ― External UL Listed 12 VDC or 24 VDC regulated power supply**

6 ― D125B Dual Class A Initiating Module

7 ― D8129 Octo-relay Module*

8 ― To on-board point or expansion module***

9 ― Connect only to one common at the control panel

10 ― To an additional D125B Powered Loop Interface Module

11 ― Jumper E1 not cut****

* When using an SDI2 control panel, use a B308 Octo-output Module and SDI2 wiring instead of the D8129 and ZONEX wiring.
** When using ground fault detect, do not reference the external power supply negative terminal to earth ground.
*** A D8128D OctoPOPIT Module or a B208 Octo-input Module can be used.
**** If power output is 24 VDC, cut Jumper E1.

Region Certifi cation

US UL APOU: Proprietary Alarm Units

(UL1076),
UOJZ: Control Units, System (UL864,
9th edition)

CSFM 7167-1615: 100

7165-1615:0242
7165-1615:0238
7165-1615:0119
7167-1615:0239

NYC­MEA

12-92-E, Vol. II 12-92-E, Vol. II
12-92-E, Vol. 12 12-92-E, Vol. 12
12-92-E, Vol. 15 12-92-E, Vol. 15

FDNY-

6059

CoA

5 | Specifi cations

Dimensions 70 mm x 76 mm (2.75 in x 3.0 in)

Relay 5 A @ 30 VDC maximum

10 A @ 5 VDC minimum

Current Max 60 mA Standby

60 mA Alarm

Power input Nominal 12 VDC with jumper intact

Nominal 24 VDC with jumper cut

Power supplies UL1481 and UL864 Listed auxiliary

12 VDC or 24 VDC regulated, power
limited power supply for Fire Protective
Signaling Units and Commercial/
Residential Burglar Units

Fire or control
panel wiring

Compatible
control panels

Copyright

This document is the intellectual property of Bosch Security
Systems, Inc. and is protected by copyright. All rights reserved.

Trademarks

All hardware and software product names used in this document
are likely to be registered trademarks and must be treated
accordingly.

Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to
the Bosch Security Systems, Inc. website at
http://www.boschsecurity.com/datecodes/.

Maximum distance - Wire size (maximum
resistance: 1

Ω

):
60 ft (18 m) - 22 AWG (0.65 mm)
160 ft (48 m) - 18 AWG (2 mm)

All Bosch Security Systems, Inc. control
panels and FACPs

Auxiliary Relay Module

D130

en Installation Guide

Bosch Security Systems, Inc.

130 Perinton Parkway
Fairport, NY 14450
USA

www.boschsecurity.com

© 2014 Bosch Security Systems, Inc. F01U.072.455 | 06 | 2014.05