bosch CC 220 User Manual

Typ1 osa / CC 220
Error messages
Antriebs- und Steuerungstechnik
Version
104
Automationstechnik
Typ1 osa / CC 220
Error messages
1995
by Robert Bosch GmbH,
All rights reserved, including applications for protective rights.
Reproduction or handing over to third parties are subject to our written permission.
Discretionary charge 20.– DM
Flexible Automation
Contents
Table of Contents
ForewordNotes on safety
1. Error messages, general 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Error messages sorted by error numbers 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Error messages sorted alphabetically 1-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Abbreviations 1-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. P2 errors 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. NC errors 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC 220 / 320
Error messages
Page
4. DNC errors 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Runtime errors 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. System errors 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Warnings 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. Panel errors 8-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Error messages of the panel 8-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. Customer area errors 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents - 1
Flexible Automation
Contents
CC 220 / 320
Error messages
Contents - 2
Flexible Automation
Foreword
General
Reference to the software version
Foreword
The information on how to avoid and rectify errors is of a fairly general nature. It cannot account individually for all of the special conditions under which the control system will be used.
We therefore suggest that you also consult the user documentation of your control system during troubleshooting. If in doubt, contact your authorized Bosch service point. If you need further information or have any serious problems with the control system that are not adequately described here or in the special user documenta tion, please contact Bosch service or our customer advisors. The addresses are provided inside the back cover of the manual.
These error messages refer to the control systems of the CC220 /320 and CC 200 / 300 series (software versions up to and including Z25NJ, D25ZA and T25XA).
CC 220 / 320
Error messages
NOTE!
The software version used in your control system is indicated in DIAGNOSTIC group operating mode when you press the DIAGNOSTIC CONTROL and SOFT WARE VERSION softkeys.
Reader target group
This manual addresses technically qualified personnel who have been specially trained and are familiar with CNC technology.
Troubleshooting done by personnel who are not trained, or not adequately trained, may result in machine and equipment damage, loss of software, or even personal injury. It is therefore important that only properly trained personnel work with the control system and its individual components.
Qualified personnel as defined by the safety notes are people who have received instruction concerning CNC equipment, project planning and programming.
Please take note of our extensive range of training courses on these subjects. Train ing proposals are provided on the inside cover of the manual. Our training centre will be glad to respond to any queries you many have. The address is on the back of the manual.
Foreword - 1
Flexible Automation
Foreword
CC 220 / 320
Error messages
Foreword - 2
Flexible Automation
Notes on safety
Please pay attention to the following safety issues:
Notes on Safety
CAUTION
Never plug in or disconnect cables/slotin assemblies unless the system is switched off.
CMOS components can be destroyed by static discharge, so make sure you are earthed before you touch such components.
Do not open batteries using force, and do not try to recharge them or throw them onto fires. Dispose of spent batteries properly. Use only original replacement bat teries.
Unless described otherwise, maintenance and repair work must never be carried out unless the system is switched off. If it is necessary to carry out measuring or
!
testing work on the system when it is switched on, it is imperative to observe all safety and accident prevention regulations. Always use suitable electrical tools.
CC 220 / 320
Error messages
Repair/maintenance work on components of the CNC must be conducted only by Bosch service or by repair/maintenance agents authorized by Bosch.
!
All work on the electrical connection must be carried out by properly qualified per sonnel only, using suitable tools.
Unauthorized opening or removal of CNC components, or incorrectly executed re pairs, can cause death, serious injury or considerable damage.
!
Removing/opening housings or a guard, or opening the switch cabinet, may ex pose equipment that carries dangerous voltages.
!
Emergency stop facilities must remain in effect in all modes of operation. Unlocking an emergency stop mechanism must never result in uncontrolled or undefined re
!
starting of the machine.
2 - 1
Flexible Automation
Explanation of the sticker symbols on the control system
Notes on Safety
The following stickers may be attached to the actual control components in order to draw your attention to certain things:
Warning, dangerous voltage!
Warning, battery hazard!
Components can be damaged by electrostatic discharge!
Disconnect power plug before opening!
Screws for connecting PE (protective earth) only!
CC 220 / 320
Error messages
Screen connection only!
2 - 2
Flexible Automation
Error messages, general
1. Error messages, general
The control system displays error messages on screen as part of its safety func tions. These messages are generated by such functions as hardware and software monitoring, input monitoring or program execution monitoring.
Errors always belong to one of the predefined error types:
System errors
Error messages with the highest priority. A system error differs from other errors types in the way it is displayed (see 6. System errors).
P2 errors
NC errors
DNC errors
Runtime errors
Warnings
CC 220 / 320
Error messages
Panel errors
Customer area errors
The error message always indicates the error type, error number and error text on the second and third row of the screen.
Example
P 1 NC0 P2 ERROR 116 MACHINE
STOPPING SERVO ERROR 13.8 18.45. . . . . . .
At the same time, the most recent error messages are written out on the DIAGNOS TIC screen under ERRORS.
P 1 NC0 P2 ERROR 116 MACHINE
ERROR PREPARATORY STATUS
SERVO ERROR . . . . . . . . . . . . . . . . . . . . .
NC ERROR: . . . . . . . . . . . . . . . . . . . . .
STOPPING SERVO ERROR 13.8 18.45. . . . . . .
1ST AXIS . . . . . . . . . . . . . . . . . . . . .
PLC TIMEOUT . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
It is not always possible to infer the exact cause of an error from the error message, since the error message is triggered by only one of a large number of possible causes.
The description attempts to specify the possible cause(s) for each error message, along with help on how to rectify the error.
1 - 1
Flexible Automation
Diagnostics
Error messages, general
CC 220 / 320
Error messages
There are various ways of clearing the error message from the screen, depending on which error occurred. In the simplest case this is done by
pressing a key returning to another level changing the mode of operation
These actions remove the error message from the header lines of the screen, but the error text is saved on the main DIAGNOSTIC screen.
DIAGNOSTIC mode provides three ways of clearing the error message from the header and in the main DIAGNOSTIC screen using softkeys.
DIAGNOSTIC DIAGNOSTIC INTERVENTION SERVICE
CONTROL MACHINE FUNCTION FUNCTION
INTERVENTION FUNCTION
HOME CLEAR CLEAR
POSITION ERROR LOGIC
Clear error
Home position
You can clear the error message using one of these functions, depending on the type and cause of the error. Sometimes the error may be rectified by restoring the control system to a controlled state.
INTERVENTION FUNCTION
HOME CLEAR CLEAR
POSITION ERROR LOGIC
Completely deletes the text of the error message. The current state is not changed.
INTERVENTION FUNCTION
HOME CLEAR CLEAR
POSITION ERROR LOGIC
Completely deletes the text of the error message. The control system displays the main DIAGNOSTIC screen. If a program is running or an input being made, for example, it will be aborted. Axis home positions are preserved, as is DNC.
Clear logic
INTERVENTION FUNCTION
HOME CLEAR CLEAR
POSITION ERROR LOGIC
Clears logic; roughly equivalent to a hardware reset. Completely deletes the text of the error message. The control system powers up. Any running program is aborted and axis home positions are lost.
1 - 2
Flexible Automation
How to use this manual
Error messages, general
The information on how to avoid and rectify errors is of a fairly general nature.
It cannot account individually for all of the special conditions under which the con trol system will be used. If in doubt, contact your authorized Bosch service point. The address of your local Bosch service point is provided inside the back cover of the manual.
In the following sections you will find the error messages sorted
by error numbers - on pages 1-4 to 1-5
alphabetically - on pages 1-16 to 1-28
in each case indicating the page on which you will find information on how to avoid and rectify the error.
Error messages that have been added since edition D3 are marked with a star (*).
The abbreviations used are explained on pages 1-29 and 1-30.
CC 220 / 320
Error messages
1 - 3
CC 220 / 320
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages
Flexible Automation
Error messages, general
1.1 Error messages sorted by error numbers
This section contains all error messages, sorted by error numbers. The error messages of the panel (see page 1-15) are listed in alphabetical order, indicating the page number where you will find further information on how to avoid and rectify the error.
Error messages that have been added since edition D3 are marked with a star (*).
Error number/error message 1
ÁÁ
2
ÁÁ
3
ÁÁ
1 2
ÁÁ
6
ÁÁ
14
ÁÁ
27
ÁÁ
50
ÁÁ
66 67
ÁÁ
72
ÁÁ
73
ÁÁ
76
ÁÁ
77
ÁÁ
78 78
ÁÁ
78
ÁÁ
79
ÁÁ
80
ÁÁ
81 99
ÁÁ
100
ÁÁ
104
ÁÁ
105
ÁÁ
113
ÁÁ
115 116
ÁÁ
117
ÁÁ
118
ÁÁ
118
ÁÁ
125
ÁÁ
125 134
ÁÁ
139
ÁÁ
146
ÁÁ
149
ÁÁ
150
ÁÁ
165 172
ÁÁ
TEXT FILE MISSING
ББББББББББББББББББББ
MACHINE PARAMETERS MISSING
ББББББББББББББББББББ
CUSTOM. EPROM ON CODE AREA
ББББББББББББББББББББ
CLEAR LOGIC WATCHDOG COUNTER P2 NOT RUNNING
ББББББББББББББББББББ
KSDEF. PART DESTROYED
ББББББББББББББББББББ
FILE TRANSFER ERROR
ББББББББББББББББББББ
ACTIVE TABLE MISSING
ББББББББББББББББББББ
TABLE NOT PRESENT
ББББББББББББББББББББ
PROGRAM NOT PRESENT INPUT ERROR
ББББББББББББББББББББ
INCORRECT INPUT
ББББББББББББББББББББ
INPUT INCORRECT
ББББББББББББББББББББ
INVALID CHARACTER
ББББББББББББББББББББ
ADDRESS EXISTS SEVERAL TIMES
ББББББББББББББББББББ
FORMAT ERROR INVALID FORMAT
ББББББББББББББББББББ
FORMAT INVALID
ББББББББББББББББББББ
UPGRADE LEVEL INACTIVE
ББББББББББББББББББББ
SIGN ERROR
ББББББББББББББББББББ
MAX. SUBROUTINE DEPTH IS MAIN BLOCK SEARCH WANTED?
ББББББББББББББББББББ
PROGRAM IN CONTROL
ББББББББББББББББББББ
MEMORY FULL
ББББББББББББББББББББ
ERROR IN FILE STRUCTURE
ББББББББББББББББББББ
NO REF. POINTS
ББББББББББББББББББББ
LIMIT SWITCH SERVO ERROR
ББББББББББББББББББББ
MARKER MISSING
ББББББББББББББББББББ
MEASURING CIRCUIT ERROR
ББББББББББББББББББББ
MEASURING SYSTEM FAULTY
ББББББББББББББББББББ
BLOCK NONEXISTENT
ББББББББББББББББББББ
INADMISSIBLE COMPENSATION VALUE TABLE IS ACTIVE
ББББББББББББББББББББ
EMERGENCY STOP PENDING
ББББББББББББББББББББ
PROGRAM IS ACTIVE
ББББББББББББББББББББ
I/O DEVICE TIMEOUT
ББББББББББББББББББББ
PARITY
ББББББББББББББББББББ
ADDRESS INVALID * LIMIT SWITCH
ББББББББББББББББББББ
1 - 4
Page 9 - 1
БББББББ
9 - 1
БББББББ
9 - 1
БББББББ
6 - 2 6 - 2
БББББББ
6 - 2
БББББББ
6 - 2
БББББББ
6 - 3
БББББББ
5 - 1
БББББББ
7 - 1 5 - 1/7 - 1
БББББББ
7 - 1
БББББББ
5 - 1/7 - 1
БББББББ
5 - 1
БББББББ
5 - 1
БББББББ
5 - 2 5 - 2/7 - 1
БББББББ
5 - 3
БББББББ
4 - 1/5 - 4/7 - 2
БББББББ
5 - 4
БББББББ
5 - 5 6 - 3
БББББББ
7 - 2
БББББББ
4 - 1/5 - 5/7 - 2
БББББББ
4 - 1/5 - 6/7 - 2
БББББББ
4 - 1/7 - 3
БББББББ
2 - 1 2 - 1
БББББББ
2 - 1
БББББББ
2 - 1
БББББББ
2 - 1
БББББББ
5 - 6/7 - 3
БББББББ
6 - 3 7 - 3
БББББББ
2 - 1
БББББББ
7 - 3
БББББББ
5 - 7/7 - 3
БББББББ
5 - 7
БББББББ
5 - 7/7 - 3 5 - 7
БББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 187
193
ÁÁ
194
ÁÁ
195
ÁÁ
196
ÁÁ
196
ÁÁ
197 202
ÁÁ
203
ÁÁ
206
ÁÁ
212
ÁÁ
214 217
ÁÁ
223
ÁÁ
231
ÁÁ
232
ÁÁ
234
ÁÁ
243 253
ÁÁ
256
ÁÁ
260
ÁÁ
261
ÁÁ
262
ÁÁ
263 264
ÁÁ
265
ÁÁ
266
ÁÁ
267
ÁÁ
268
ÁÁ
269 270
ÁÁ
271
ÁÁ
272
ÁÁ
273
ÁÁ
274
ÁÁ
275 276
ÁÁ
277
ÁÁ
280
ÁÁ
281
ÁÁ
282
ÁÁ
305 323
ÁÁ
324
ÁÁ
326
ÁÁ
332
ÁÁ
333 336
ÁÁ
344
ÁÁ
346
ÁÁ
351
FILE HAS DFS IDENTIFIER INVALID TANGENT
ББББББББББББББББББББ
POSITION ERROR
ББББББББББББББББББББ
NEGATIVE ROOT
ББББББББББББББББББББ
INVALID REAL VALUE
ББББББББББББББББББББ
ENCODER DEFECTIVE
ББББББББББББББББББББ
F NOT PREALLOCATED TIMING ERROR IN WAITFORRXR
ББББББББББББББББББББ
NO INTERROGATION
ББББББББББББББББББББ
FILE NOT DELETABLE
ББББББББББББББББББББ
WRONG DIAG. VERSION
ББББББББББББББББББББ
TIME TO BE SET ERROR IN DIAGN. PRG.
ББББББББББББББББББББ
CLEAR RESIDUAL DISTANCE G41/42
ББББББББББББББББББББ
TIMING ERROR IN PLSINI
ББББББББББББББББББББ
RAM ECHO ERROR IN PLSINI
ББББББББББББББББББББ
NO RXR BIT FOR PANEL INTERRUPT
ББББББББББББББББББББ
WRONG CODE NUMBER WRONG INTERRUPT PCB
ББББББББББББББББББББ
COUPLING BOARD RESET
ББББББББББББББББББББ
NMI
ББББББББББББББББББББ
ABORT
ББББББББББББББББББББ
FPU TRAP
ББББББББББББББББББББ
ILLEGAL OPERAND SVC TRAP
ББББББББББББББББББББ
DIV BY ZERO
ББББББББББББББББББББ
FLAG TRAP
ББББББББББББББББББББ
BREAKPOINT REACHED
ББББББББББББББББББББ
TRACE TRAP
ББББББББББББББББББББ
UNDEFINED OPCODE ERROR: DUAL PORT TEST
ББББББББББББББББББББ
ERROR: PARTY LINE TEST
ББББББББББББББББББББ
ERROR: RAM TEST
ББББББББББББББББББББ
ERROR: RELOAD TEXT
ББББББББББББББББББББ
SVC NO. 6
ББББББББББББББББББББ
HEAP OVERFLOW SQRT OF NEG. ARGUMENT
ББББББББББББББББББББ
BACKUP VERSION ACTIVE
ББББББББББББББББББББ
ERROR: P2 INIT
ББББББББББББББББББББ
TIMEOUT BY WAIT FOR P2
ББББББББББББББББББББ
CRITICAL SECTION NOT ENDED
ББББББББББББББББББББ
MEMORY FULL EDIT ENABLE MISSING
ББББББББББББББББББББ
PROGRAM ACTIVE
ББББББББББББББББББББ
INADMISSIBLE FILE NUMBER
ББББББББББББББББББББ
MAILBOX FULL
ББББББББББББББББББББ
PANEL NOT SUITABLE LINKING ABORTED
ББББББББББББББББББББ
INPUT INCORRECT, AXIS RUNNING
ББББББББББББББББББББ
TOO MANY AXIS MOVEMENTS
ББББББББББББББББББББ
ALL LINK TAB. ACTIVE
1 - 5
Page 7 - 4
6 - 3
БББББББ
2 - 1
БББББББ
6 - 3
БББББББ
6 - 3
БББББББ
2 - 2
БББББББ
7 - 4 6 - 3
БББББББ
6 - 3
БББББББ
5 - 8
БББББББ
7 - 4
БББББББ
5 - 8 7 - 4
БББББББ
7 - 4
БББББББ
6 - 3
БББББББ
6 - 4
БББББББ
6 - 4
БББББББ
7 - 4 6 - 4
БББББББ
6 - 4
БББББББ
6 - 4
БББББББ
6 - 4
БББББББ
6 - 4
БББББББ
6 - 4 6 - 4
БББББББ
6 - 4
БББББББ
6 - 5
БББББББ
6 - 5
БББББББ
6 - 5
БББББББ
6 - 5 6 - 5
БББББББ
6 - 5
БББББББ
6 - 5
БББББББ
6 - 5
БББББББ
6 - 5
БББББББ
6 - 5 6 - 6
БББББББ
6 - 6
БББББББ
6 - 6
БББББББ
6 - 6
БББББББ
6 - 6
БББББББ
4 - 1 4 - 1/7 - 4
БББББББ
4 - 1
БББББББ
5 - 8
БББББББ
7 - 4
БББББББ
7 - 4 7 - 5
БББББББ
5 - 8
БББББББ
7 - 5
БББББББ
5 - 8
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 354
355
ÁÁ
356
ÁÁ
372
ÁÁ
373
ÁÁ
374
ÁÁ
375 377
ÁÁ
379
ÁÁ
386
ÁÁ
387
ÁÁ
388 389
ÁÁ
390
ÁÁ
391
ÁÁ
392
ÁÁ
393
ÁÁ
394 395
ÁÁ
396
ÁÁ
397
ÁÁ
398
ÁÁ
399
ÁÁ
400 401
ÁÁ
592
ÁÁ
615
ÁÁ
621
ÁÁ
696
ÁÁ
703 704
ÁÁ
708
ÁÁ
739
ÁÁ
786
ÁÁ
787
ÁÁ
788 789
ÁÁ
789
ÁÁ
790
ÁÁ
791
ÁÁ
792
ÁÁ
793 794
ÁÁ
795
ÁÁ
796
ÁÁ
797
ÁÁ
798 798
ÁÁ
799
ÁÁ
800
ÁÁ
800
LINKING ALREADY ACTIVE LINK ERROR
ББББББББББББББББББББ
NO RUNTIME MEMORY
ББББББББББББББББББББ
LSEC LOGIC
ББББББББББББББББББББ
LSEC SYNTAX
ББББББББББББББББББББ
LSEC GRID
ББББББББББББББББББББ
LSEC OVERFLOW NO CONTROL RESET POSSIBLE
ББББББББББББББББББББ
FILE DESTROYED
ББББББББББББББББББББ
LIMIT SWITCH 1ST AXIS
ББББББББББББББББББББ
LIMIT SWITCH 2ND AXIS
ББББББББББББББББББББ
LIMIT SWITCH 3RD AXIS LIMIT SWITCH 4TH AXIS
ББББББББББББББББББББ
LIMIT SWITCH 5TH AXIS
ББББББББББББББББББББ
LIMIT SWITCH 6TH AXIS
ББББББББББББББББББББ
LIMIT SWITCH 7TH AXIS
ББББББББББББББББББББ
LIMIT SWITCH 8TH AXIS
ББББББББББББББББББББ
INVALID COMPENSATION VALUE INVALID ZERO SHIFT GROUP
ББББББББББББББББББББ
INVALID FILE GROUP
ББББББББББББББББББББ
FILE NAME FAULTY
ББББББББББББББББББББ
PROTECTION FAULTY
ББББББББББББББББББББ
FILE PROTECTED
ББББББББББББББББББББ
INVALID DISTURBANCE TABLE NO DISTURBANCE TABLE
ББББББББББББББББББББ
WRONG TOOL TYPE
ББББББББББББББББББББ
EPROM ERROR
ББББББББББББББББББББ
CODE RANGE 4 NOT AVAILABLE
ББББББББББББББББББББ
MEMORY FULL
ББББББББББББББББББББ
MACRO ADDRESS NOT PRESENT FOR RESET MSG NOT PRESENT FOR OUTPUT
ББББББББББББББББББББ
INCORRECT USE OF DO-AGAIN FLAG
ББББББББББББББББББББ
ERR BLOCKCON
ББББББББББББББББББББ
DEAD ZONE BLOCKED
ББББББББББББББББББББ
INVALID CVALUE *
ББББББББББББББББББББ
INADMISSIBLE AVALUE G6 W/O AXIS INFO *
ББББББББББББББББББББ
TAP TOO SMALL
ББББББББББББББББББББ
NO E WORD PROGRAMMED
ББББББББББББББББББББ
INCORRECT CIRCULAR PATH PROGRAMMING
ББББББББББББББББББББ
INVALID E WORD
ББББББББББББББББББББ
INVALID H WORD H WITHOUT TRAVERSING INFO
ББББББББББББББББББББ
LIMIT POSITION WRONGLY CALCULATED
ББББББББББББББББББББ
INVALID LIMIT POSITION
ББББББББББББББББББББ
MAXIM. 4 CLAWS
ББББББББББББББББББББ
WRONG MODE IN READ INVALID PC OPERAND
ББББББББББББББББББББ
INVALID PC COMMAND
ББББББББББББББББББББ
SOFTKEY PARAMETER < 0
ББББББББББББББББББББ
ERROR IN PLC PROGRAM
1 - 6
Page 5 - 8
5 - 8/7 - 5
БББББББ
5 - 8
БББББББ
7 - 5
БББББББ
7 - 5
БББББББ
7 - 6
БББББББ
7 - 6 7 - 6
БББББББ
5 - 8
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9/7 - 6 5 - 9/7 - 6
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9/7 - 6
БББББББ
5 - 9 5 - 9
БББББББ
4 - 1/5 - 9
БББББББ
5 - 9
БББББББ
5 - 9
БББББББ
4 - 2/5 - 9/7 - 7
БББББББ
7 - 7 7 - 7
БББББББ
7 - 7
БББББББ
6 - 6
БББББББ
6 - 6
БББББББ
5 - 10
БББББББ
6 - 6 6 - 6
БББББББ
6 - 6
БББББББ
6 - 6
БББББББ
5 - 10
БББББББ
5 - 10
БББББББ
5 - 10 5 - 10
БББББББ
5 - 10
БББББББ
5 - 10
БББББББ
5 - 10
БББББББ
5 - 10
БББББББ
5 - 10 5 - 10
БББББББ
5 - 10
БББББББ
5 - 10
БББББББ
5 - 11
БББББББ
6 - 7 7 - 7
БББББББ
7 - 7
БББББББ
6 - 7
БББББББ
5 - 11
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 804
805
ÁÁ
806
ÁÁ
810
ÁÁ
813
ÁÁ
814
ÁÁ
815 815
ÁÁ
816
ÁÁ
817
ÁÁ
818
ÁÁ
832 851
ÁÁ
950
ÁÁ
990
ÁÁ
991
ÁÁ
992
ÁÁ
993 994
ÁÁ
995
ÁÁ
998
ÁÁ
999
ÁÁ
1079
ÁÁ
1080 1120
ÁÁ
1131
ÁÁ
1137
ÁÁ
1168
ÁÁ
1169
ÁÁ
1170 1188
ÁÁ
1189
ÁÁ
1190
ÁÁ
1191
ÁÁ
1216
ÁÁ
1217 1218
ÁÁ
1220
ÁÁ
1228
ÁÁ
1236
ÁÁ
1242
ÁÁ
1258 1259
ÁÁ
1317
ÁÁ
1322
ÁÁ
1365
ÁÁ
1366 1367
ÁÁ
1368
ÁÁ
1390
ÁÁ
LSEC FILE DEFECTIVE ERROR IN LSEC FILE PROCESSING
ББББББББББББББББББББ
EPROM WRITE PROTECTED
ББББББББББББББББББББ
FORMAT NOT AGREED
ББББББББББББББББББББ
FILE GROUP NOT DEFINED (OPEN AND CLOSE)
ББББББББББББББББББББ
PROGRAM MEMORY DESTROYED!
ББББББББББББББББББББ
POINTER IN LIST OR TREE MANAGEMENT DESTROYED PLC BATTERY EMPTY
ББББББББББББББББББББ
ERROR IN USER HEAP
ББББББББББББББББББББ
LSV2 STATUS DATA FAULT *
ББББББББББББББББББББ
ILLEGAL POINTER WHEN CLOSING FILE *
ББББББББББББББББББББ
PC PROGRAM TOO LARGE COPY FILE NOT PRESENT
ББББББББББББББББББББ
STACK SUBRANGE EXHAUSTED
ББББББББББББББББББББ
ILLEGAL MEMORY ACCESS
ББББББББББББББББББББ
TASK MISSING IN NOTQ
ББББББББББББББББББББ
TASK STILL ACTIVE
ББББББББББББББББББББ
TASKEND WITHOUT STOP WRONG USE OF OPTIONS
ББББББББББББББББББББ
TASK TRANSFER IMPOSSIBLE
ББББББББББББББББББББ
ILLEGAL PARAMETER IN UTILITY
ББББББББББББББББББББ
STACK OVERFLOW
ББББББББББББББББББББ
CHANGE TO MDI
ББББББББББББББББББББ
LINK TAB. NOT PRESENT E DIR. INCOMPLETE
ББББББББББББББББББББ
FILE IN LIBRARY
ББББББББББББББББББББ
LOAD COMP. TABLE
ББББББББББББББББББББ
COMM. STORE USED
ББББББББББББББББББББ
PLC FM TIMEOUT
ББББББББББББББББББББ
PLC FM INCORRECT OLD LANGUAGE VERSION
ББББББББББББББББББББ
CUSTOMER EPROM TOO SMAL
ББББББББББББББББББББ
CHECKSUM CUSTOMER EPROM
ББББББББББББББББББББ
CUSTOMER EPROM IN WRONG PLACE
ББББББББББББББББББББ
FEED OVERRIDE TABLE MISSING
ББББББББББББББББББББ
SWITCHOVER NOT PERMITTED INVALID PROGRAMMING
ББББББББББББББББББББ
TEST ACTIVE
ББББББББББББББББББББ
OSCILLATING AXIS ACTIVE
ББББББББББББББББББББ
G92 IS ACTIVE *
ББББББББББББББББББББ
KS ACCESS BLOCKED
ББББББББББББББББББББ
DRIVE ON ERROR STARTING NOT POSSIBLE
ББББББББББББББББББББ
MEMORY OVERFLOW
ББББББББББББББББББББ
OPTIMIZATION BUFFER FULL
ББББББББББББББББББББ
INSUFFICIENT CHECK POINTS
ББББББББББББББББББББ
INVALID G CODE INVALID CHECK POINT
ББББББББББББББББББББ
INVALID WORKING AREA
ББББББББББББББББББББ
SIMULATION MEMORY FULL
ББББББББББББББББББББ
1 - 7
Page 6 - 7
6 - 7
БББББББ
7 - 7
БББББББ
6 - 7
БББББББ
6 - 7
БББББББ
6 - 8
БББББББ
6 - 8 7 - 7
БББББББ
6 - 8
БББББББ
6 - 8
БББББББ
6 - 8
БББББББ
7 - 8 6 - 8
БББББББ
6 - 8
БББББББ
6 - 8
БББББББ
6 - 8
БББББББ
6 - 9
БББББББ
6 - 9 6 - 9
БББББББ
6 - 9
БББББББ
6 - 9
БББББББ
6 - 9
БББББББ
7 - 8
БББББББ
5 - 11/7 - 8 7 - 8
БББББББ
4 - 2/5 - 11/7 - 8
БББББББ
5 - 11
БББББББ
7 - 8
БББББББ
7 - 8
БББББББ
7 - 8 7 - 8
БББББББ
7 - 9
БББББББ
7 - 9
БББББББ
7 - 9
БББББББ
7 - 9
БББББББ
5 - 11 5 - 12
БББББББ
7 - 9
БББББББ
5 - 12
БББББББ
5 - 12
БББББББ
5 - 12
БББББББ
5 - 12 5 - 12
БББББББ
7 - 9
БББББББ
7 - 9
БББББББ
5 - 12
БББББББ
5 - 12 5 - 13
БББББББ
5 - 13
БББББББ
7 - 9
БББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 1409
1418
ÁÁ
1427
ÁÁ
1428
ÁÁ
1429
ÁÁ
1440
ÁÁ
1441 1449
ÁÁ
1451
ÁÁ
1456
ÁÁ
1457
ÁÁ
1458 1459
ÁÁ
1463
ÁÁ
1464
ÁÁ
1466
ÁÁ
1470
ÁÁ
1472 1473
ÁÁ
1474
ÁÁ
1475
ÁÁ
1480
ÁÁ
1498
ÁÁ
1499 1500
ÁÁ
1505
ÁÁ
1507
ÁÁ
1535
ÁÁ
1536
ÁÁ
1541 1542
ÁÁ
1543
ÁÁ
1544
ÁÁ
1550
ÁÁ
1551
ÁÁ
1553 1553
ÁÁ
1554
ÁÁ
1554
ÁÁ
1555
ÁÁ
1555
ÁÁ
1556 1557
ÁÁ
1558
ÁÁ
1559
ÁÁ
1577
ÁÁ
1879 1983
ÁÁ
1984
ÁÁ
1985
ÁÁ
1986
WEAR ALTERNATIVE TOOL
ББББББББББББББББББББ
INVALID X ZERO SHIFT
ББББББББББББББББББББ
+X SIDE WRONG (MPP 7513)
ББББББББББББББББББББ
-X SIDE WRONG (MPP 7513)
ББББББББББББББББББББ
G92 OR ZERO SHIFT GROUP CHANGED
ББББББББББББББББББББ
C AXIS NOT ACTIVE ZERO SHIFT OR COMP. CHANGE IN G491
ББББББББББББББББББББ
T WITH ACTIVE G491
ББББББББББББББББББББ
TABLE CHANGE WITH ACTIVE G491
ББББББББББББББББББББ
FALSE PARAMETER ID *
ББББББББББББББББББББ
PERMITTED VALUE RANGE EXCEEDED INVALID STRING/TRANSFER ERROR
ББББББББББББББББББББ
TOOL NO. NOT DEFINED
ББББББББББББББББББББ
COMP. NO. NOT DEFINED
ББББББББББББББББББББ
NO LZ VALUE
ББББББББББББББББББББ
NO ALT. TOOL
ББББББББББББББББББББ
NO COMPENSATION GROUP ACTIVE NO TOOL ACTIVE
ББББББББББББББББББББ
G92 X.. NOT PERMITTED
ББББББББББББББББББББ
TOOL CHANGE ONLY WITH G40
ББББББББББББББББББББ
ALT. COMP. GROUP INVALID
ББББББББББББББББББББ
TOOL DATA W1-W4 MISSING
ББББББББББББББББББББ
INVALID PROGR. IDENTIFIER INVALID TOOL CALL
ББББББББББББББББББББ
TOOL CHANGE ACKNOWLEDGEMENT
ББББББББББББББББББББ
INVALID CHANGE POSITION
ББББББББББББББББББББ
INVALID TURNING TOOL
ББББББББББББББББББББ
ZERO OFFSET NOT APPROACHED
ББББББББББББББББББББ
CUTTER RADIUS NOT MONITORED MIDPROGRAM NOT PERMITTED *
ББББББББББББББББББББ
G108 ACTIVE *
ББББББББББББББББББББ
DISTANCE FROM DATUM *
ББББББББББББББББББББ
G33: LEAD NOT PERMITTED
ББББББББББББББББББББ
SPINDLE SPEED NOT PERMITTED
ББББББББББББББББББББ
G33: RETRACTION NOT PERMITTED RETRACTION NOT POSSIBLE
ББББББББББББББББББББ
ALL VARIANTS
ББББББББББББББББББББ
FEED NOT PERMITTED
ББББББББББББББББББББ
NO DIST. PROGRAMMED
ББББББББББББББББББББ
NO G96 POSSIBLE
ББББББББББББББББББББ
SYNCHR. NOT POSSIBLE * SPINDLE PROG. INVALID *
ББББББББББББББББББББ
SPINDLE INTERF. ERROR *
ББББББББББББББББББББ
M30 WITH ACT. SYNC. *
ББББББББББББББББББББ
BARRIERS EXCEEDED
ББББББББББББББББББББ
PROGRAM ACTIVE * T TABLE RENAMED
ББББББББББББББББББББ
TABLE NOT ACCEPTED
ББББББББББББББББББББ
ADDRESS "S" MISSING *
ББББББББББББББББББББ
ADDRESS S" OR F" MISSING
1 - 8
Page 7 - 9
5 - 13
БББББББ
5 - 13
БББББББ
5 - 13
БББББББ
5 - 13
БББББББ
5 - 13
БББББББ
5 - 13 5 - 13
БББББББ
5 - 14
БББББББ
5 - 14
БББББББ
5 - 14
БББББББ
5 - 14 5 - 14
БББББББ
5 - 14
БББББББ
5 - 14
БББББББ
5 - 14
БББББББ
7 - 9
БББББББ
5 - 15 5 - 15
БББББББ
5 - 15
БББББББ
5 - 15
БББББББ
5 - 15/7 - 10
БББББББ
5 - 15
БББББББ
5 - 15 5 - 15
БББББББ
7 - 10
БББББББ
5 - 15
БББББББ
5 - 15
БББББББ
5 - 16
БББББББ
7 - 10 5 - 16/7 - 10
БББББББ
5 - 16
БББББББ
5 - 16
БББББББ
5 - 16
БББББББ
5 - 16
БББББББ
5 - 16 5 - 16
БББББББ
5 - 16
БББББББ
5 - 17
БББББББ
5 - 17
БББББББ
5 - 17
БББББББ
5 - 17 5 - 17
БББББББ
5 - 17
БББББББ
5 - 17
БББББББ
5 - 18
БББББББ
7 - 10 7 - 10
БББББББ
7 - 10
БББББББ
5 - 18
БББББББ
5 - 18
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 1987
2003
ÁÁ
2005
ÁÁ
2008
ÁÁ
2010
ÁÁ
2011
ÁÁ
2014 2015
ÁÁ
2020
ÁÁ
2028
ÁÁ
2030
ÁÁ
2031 2040
ÁÁ
2041
ÁÁ
2042
ÁÁ
2043
ÁÁ
2044
ÁÁ
2045 2046
ÁÁ
2048
ÁÁ
2049
ÁÁ
2095
ÁÁ
2098
ÁÁ
2101 2102
ÁÁ
2103
ÁÁ
2104
ÁÁ
2105
ÁÁ
2106
ÁÁ
2107 2108
ÁÁ
2109
ÁÁ
2110
ÁÁ
2115
ÁÁ
2116
ÁÁ
2120 2121
ÁÁ
2122
ÁÁ
2123
ÁÁ
2125
ÁÁ
2126
ÁÁ
2131 2132
ÁÁ
2133
ÁÁ
2134
ÁÁ
2136
ÁÁ
2137 2138
ÁÁ
2140
ÁÁ
2141
PROFILE NONEXISTENT AXIS RUNNING
ББББББББББББББББББББ
CLOSE BRACKETS MISSING
ББББББББББББББББББББ
FILE NONEXISTENT
ББББББББББББББББББББ
FILE ALREADY EXISTS
ББББББББББББББББББББ
FILE IS ACTIVE
ББББББББББББББББББББ
FILE TRANSFER ERROR INVALID LEVEL *
ББББББББББББББББББББ
RADIUS > 5000 MM
ББББББББББББББББББББ
INVALID WEIGHTING FACTOR
ББББББББББББББББББББ
CLG VALUE INVALID
ББББББББББББББББББББ
G14 WITHOUT AXIS INFO G2/3: F/R INVALID
ББББББББББББББББББББ
INVALID CIRCLE PARAMETER
ББББББББББББББББББББ
G2/3: INVALID NUMBER OF AXES
ББББББББББББББББББББ
G5: DIRECTION UNDEFINED
ББББББББББББББББББББ
G5: RADIUS TOO LARGE
ББББББББББББББББББББ
G5: AFTER HELICAL G5: AFTER LEVEL CHANGE
ББББББББББББББББББББ
UNEQUAL FACTORS
ББББББББББББББББББББ
LEAD TOO LARGE
ББББББББББББББББББББ
ERROR IN ECODE
ББББББББББББББББББББ
PERM. VARIABLE BLOCKED
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 1 PROHIB. WORKING AREA AXIS 2
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 3
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 4
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 5
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 6
ББББББББББББББББББББ
PROHIB. WORKING AREA AXIS 7 PROHIB. WORKING AREA AXIS 8
ББББББББББББББББББББ
PROHIB. WORKING AREA CIRCLE
ББББББББББББББББББББ
WORKING AREA MAX. 3 AXES
ББББББББББББББББББББ
SUBROUTINE CALL MISSING
ББББББББББББББББББББ
NO AXIS COUPLING POSSIBLE *
ББББББББББББББББББББ
TOO MANY BLOCKS SUPPRESSED LEVEL CHANGE ACT. COMP.
ББББББББББББББББББББ
COLLISION!
ББББББББББББББББББББ
NO INTERSECTION
ББББББББББББББББББББ
INVALID COMPENSATION VALUE
ББББББББББББББББББББ
SEVERAL ZERO SHIFTS ACTIVE
ББББББББББББББББББББ
COMP. ENTRY WITH CIRCLE COMP. CANCEL WITH CIRCLE
ББББББББББББББББББББ
CHANGE G41/42 WITH CIRCLE
ББББББББББББББББББББ
COMP. ACT. AT PROGRAM END
ББББББББББББББББББББ
G ADDR. INVALID FOR G41/42
ББББББББББББББББББББ
SINGLE BLOCK WITH G41/42 NO COMPENSATION ACTIVE
ББББББББББББББББББББ
MODAL SUBROUTINE IS ACTIVE
ББББББББББББББББББББ
DSP FORMAT WRONG
1 - 9
Page 7 - 10
7 - 11
БББББББ
5 - 18
БББББББ
5 - 18/7 - 11
БББББББ
4 - 2/7 - 11/5 - 18
БББББББ
7 - 11
БББББББ
4 - 2/6 - 9 5 - 18
БББББББ
5 - 19
БББББББ
5 - 19
БББББББ
5 - 19
БББББББ
5 - 19 5 - 19
БББББББ
5 - 19
БББББББ
5 - 19
БББББББ
5 - 19
БББББББ
5 - 19
БББББББ
5 - 19 5 - 20
БББББББ
5 - 20
БББББББ
5 - 20
БББББББ
5 - 20/7 - 11
БББББББ
5 - 20
БББББББ
5 - 20 5 - 20
БББББББ
5 - 20
БББББББ
5 - 20
БББББББ
5 - 20
БББББББ
5 - 20
БББББББ
5 - 20 5 - 20
БББББББ
5 - 20
БББББББ
5 - 20
БББББББ
7 - 11
БББББББ
5 - 20
БББББББ
5 - 21 5 - 21
БББББББ
5 - 21
БББББББ
5 - 22
БББББББ
5 - 22
БББББББ
5 - 22
БББББББ
5 - 22 5 - 23
БББББББ
5 - 23
БББББББ
5 - 23
БББББББ
5 - 23
БББББББ
5 - 23 5 - 23
БББББББ
5 - 24
БББББББ
7 - 12
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 2142
2143
ÁÁ
2144
ÁÁ
2145
ÁÁ
2150
ÁÁ
2151
ÁÁ
2152 2153
ÁÁ
2154
ÁÁ
2155
ÁÁ
2156
ÁÁ
2157 2158
ÁÁ
2159
ÁÁ
2160
ÁÁ
2161
ÁÁ
2162
ÁÁ
2163 2164
ÁÁ
2165
ÁÁ
2166
ÁÁ
2167
ÁÁ
2168
ÁÁ
2169 2170
ÁÁ
2171
ÁÁ
2172
ÁÁ
2173
ÁÁ
2174
ÁÁ
2175 2176
ÁÁ
2177
ÁÁ
2178
ÁÁ
2179
ÁÁ
2180
ÁÁ
2181 2182
ÁÁ
2183
ÁÁ
2184
ÁÁ
2185
ÁÁ
2186
ÁÁ
2187 2188
ÁÁ
2189
ÁÁ
2190
ÁÁ
2191
ÁÁ
2193 2194
ÁÁ
2195
ÁÁ
2196
ÁÁ
2197
NO M2 OR M30 PLEASE ENABLE MEMORY
ББББББББББББББББББББ
MEMORY IS OCCUPIED
ББББББББББББББББББББ
TOO MANY VARIABLES
ББББББББББББББББББББ
INSUFFICIENT MEMORY
ББББББББББББББББББББ
VARIABLE TYPE WRONG
ББББББББББББББББББББ
SUBROUTINE NONEXISTENT NESTING TOO DEEP
ББББББББББББББББББББ
VARIABLE NOT OCCUPIED
ББББББББББББББББББББ
WRONG INDEX
ББББББББББББББББББББ
P NOT IN CALLCHAIN
ББББББББББББББББББББ
SELFCALL PROHIBITED INVALID STATEMENT
ББББББББББББББББББББ
THEN MISSING
ББББББББББББББББББББ
ENDIF MISSING
ББББББББББББББББББББ
WRONG BRANCH DESTINATION
ББББББББББББББББББББ
UNTIL MISSING
ББББББББББББББББББББ
TO MISSING NEXT MISSING
ББББББББББББББББББББ
DO MISSING
ББББББББББББББББББББ
END MISSING
ББББББББББББББББББББ
= MISSING
ББББББББББББББББББББ
INADMISSIBLE VARIABLE
ББББББББББББББББББББ
) MISSING INVALID EXPRESSION
ББББББББББББББББББББ
- NOT PERMITTED
ББББББББББББББББББББ
TYPE MUST BE BIT
ББББББББББББББББББББ
INVALID OPERAND
ББББББББББББББББББББ
INVALID RELATION
ББББББББББББББББББББ
INVALID ASSIGNMENT ] MISSING
ББББББББББББББББББББ
( MISSING
ББББББББББББББББББББ
BLOCK NONEXISTENT
ББББББББББББББББББББ
LINE NONEXISTENT
ББББББББББББББББББББ
LABEL NONEXISTENT
ББББББББББББББББББББ
INVALID FIELD LIMIT INVALID FIELD TYPE
ББББББББББББББББББББ
INVALID FIELD INDEX
ББББББББББББББББББББ
INVALID PARAMETER
ББББББББББББББББББББ
MULTIPLE SUBROUTINE PROHIBITED
ББББББББББББББББББББ
INVALID PERMVARIABLE
ББББББББББББББББББББ
" MISSING PARAMETER ERROR
ББББББББББББББББББББ
INVALID LABEL
ББББББББББББББББББББ
ERROR IN NC BLOCK
ББББББББББББББББББББ
DIVISION BY 0
ББББББББББББББББББББ
INVALID TAN INVALID ASIN ACOS
ББББББББББББББББББББ
NEGATIVE ROOT
ББББББББББББББББББББ
INVALID REAL VALUE
ББББББББББББББББББББ
PROHIB. WORKING AREA
1 - 10
Page 5 - 24/7 - 12
7 - 12
БББББББ
5 - 24/7 - 12
БББББББ
5 - 24
БББББББ
5 - 24/7 - 13
БББББББ
5 - 24
БББББББ
5 - 24 5 - 25
БББББББ
5 - 25
БББББББ
5 - 25
БББББББ
7 - 13
БББББББ
5 - 25 5 - 25
БББББББ
5 - 25
БББББББ
5 - 26
БББББББ
5 - 26
БББББББ
5 - 26
БББББББ
5 - 26 5 - 26
БББББББ
5 - 26
БББББББ
5 - 26
БББББББ
5 - 26
БББББББ
5 - 27
БББББББ
5 - 28 5 - 29
БББББББ
5 - 29
БББББББ
5 - 30
БББББББ
5 - 30
БББББББ
5 - 30
БББББББ
5 - 30 5 - 31
БББББББ
5 - 31
БББББББ
5 - 31
БББББББ
5 - 32
БББББББ
5 - 32
БББББББ
5 - 32 5 - 32
БББББББ
5 - 32
БББББББ
5 - 33
БББББББ
5 - 37
БББББББ
5 - 37
БББББББ
5 - 37 5 - 38
БББББББ
5 - 38
БББББББ
5 - 38
БББББББ
5 - 39
БББББББ
5 - 39 5 - 39
БББББББ
5 - 39
БББББББ
5 - 40
БББББББ
5 - 40
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 2208
2210
ÁÁ
2211
ÁÁ
2212
ÁÁ
2213
ÁÁ
2214
ÁÁ
2216 2217
ÁÁ
2218
ÁÁ
2219
ÁÁ
2220
ÁÁ
2221 2222
ÁÁ
2223
ÁÁ
2224
ÁÁ
2225
ÁÁ
2226
ÁÁ
2227 2228
ÁÁ
2230
ÁÁ
2241
ÁÁ
2242
ÁÁ
2243
ÁÁ
2244 2245
ÁÁ
2246
ÁÁ
2247
ÁÁ
2248
ÁÁ
2249
ÁÁ
2257 2258
ÁÁ
2275
ÁÁ
2281
ÁÁ
2290
ÁÁ
2310
ÁÁ
2355 2357
ÁÁ
2358
ÁÁ
2363
ÁÁ
2366
ÁÁ
2368
ÁÁ
2370 2372
ÁÁ
2374
ÁÁ
2376
ÁÁ
2377
ÁÁ
2378 2379
ÁÁ
2380
ÁÁ
2381
TABLE NOT CREATED ENDDLG MISSING
ББББББББББББББББББББ
DLG MISSING
ББББББББББББББББББББ
WRONG INPUT FORMAT
ББББББББББББББББББББ
WRONG PRINT FORMAT
ББББББББББББББББББББ
WRONG SOFTKEY FORMAT
ББББББББББББББББББББ
PRN INSTRUCTION MISSING INPUT INSTRUCTION DOUBLE
ББББББББББББББББББББ
CHANGE TO AUTO
ББББББББББББББББББББ
PRN INVALID
ББББББББББББББББББББ
FILE NONEXISTENT
ББББББББББББББББББББ
LOG NUMBER INVALID FILE NOT OPENED
ББББББББББББББББББББ
FILE END REACHED
ББББББББББББББББББББ
FILE IN USE
ББББББББББББББББББББ
INTERFACE INVALID
ББББББББББББББББББББ
FILE LENGTH INVALID
ББББББББББББББББББББ
BLOCK > 128 BYTES FILE NAME INVALID
ББББББББББББББББББББ
GRAPHICS ALREADY ACTIVE
ББББББББББББББББББББ
RANGE EXCEEDED
ББББББББББББББББББББ
UNAUTHORIZED ACCESS
ББББББББББББББББББББ
RANGE NOT PRESENT
ББББББББББББББББББББ
WRONG COM FORMAT REAL NUMBER OVERFLOW
ББББББББББББББББББББ
INVALID COMPONENT LENGTH
ББББББББББББББББББББ
INVALID COMPONENT
ББББББББББББББББББББ
CHARACTER AREA NOT OCCUPIED
ББББББББББББББББББББ
BLOCK > 127 BYTES
ББББББББББББББББББББ
INVALID FILE INVALID INTEGER
ББББББББББББББББББББ
HEAP OVERFLOW
ББББББББББББББББББББ
TIMEOUT WHILE WAITING FOR P2
ББББББББББББББББББББ
INVALID VALUE
ББББББББББББББББББББ
INTERNAL
ББББББББББББББББББББ
DNC ACTIVE START BY CENTRAL CONTROL UNIT ONLY
ББББББББББББББББББББ
NO DIAG. START POSSIBLE
ББББББББББББББББББББ
REMOTE DIAGNOSIS ACTIVE
ББББББББББББББББББББ
V.24 ERROR USER A
ББББББББББББББББББББ
V.24 OVERFLOW USER A
ББББББББББББББББББББ
V.24 PARITY USER A V.24 PROTOC. ERROR USER A
ББББББББББББББББББББ
V.24 INTERRUPTION USER A
ББББББББББББББББББББ
RESTART ERROR
ББББББББББББББББББББ
EPROM ERROR
ББББББББББББББББББББ
V.24 RAM1 ERROR V.24 RAM2 ERROR
ББББББББББББББББББББ
V.24 COMMAND ERROR
ББББББББББББББББББББ
V.24 INIT ERROR
1 - 11
Page 7 - 13
5 - 40
БББББББ
5 - 40
БББББББ
5 - 40
БББББББ
5 - 41
БББББББ
5 - 43/7 - 13
БББББББ
5 - 43 5 - 43
БББББББ
7 - 13
БББББББ
5 - 43
БББББББ
5 - 43/4 - 2
БББББББ
5 - 44 5 - 44
БББББББ
5 - 44
БББББББ
5 - 45
БББББББ
5 - 45
БББББББ
5 - 45
БББББББ
5 - 46 5 - 46
БББББББ
7 - 13
БББББББ
5 - 46
БББББББ
5 - 47
БББББББ
5 - 47
БББББББ
5 - 47 5 - 47
БББББББ
7 - 14
БББББББ
7 - 14
БББББББ
5 - 47
БББББББ
5 - 47
БББББББ
5 - 47 5 - 48
БББББББ
7 - 14
БББББББ
7 - 14
БББББББ
5 - 48/7 - 14
БББББББ
7 - 14
БББББББ
5 - 48 7 - 14
БББББББ
7 - 14
БББББББ
7 - 15
БББББББ
4 - 2
БББББББ
4 - 2
БББББББ
4 - 2 4 - 2
БББББББ
4 - 2
БББББББ
4 - 2
БББББББ
4 - 3
БББББББ
4 - 3 4 - 3
БББББББ
4 - 3
БББББББ
7 - 15
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 2387
2389
ÁÁ
2390
ÁÁ
2391
ÁÁ
2392 2393
ÁÁ
2395
ÁÁ
2397
ÁÁ
2398
ÁÁ
2399 2587
ÁÁ
2588
ÁÁ
2602
ÁÁ
2603
ÁÁ
2604 2605
ÁÁ
2606
ÁÁ
2607
ÁÁ
2608 2609
ÁÁ
2610
ÁÁ
2611
ÁÁ
2612
ÁÁ
2613 2614
ÁÁ
2615
ÁÁ
2616
ÁÁ
2617
ÁÁ
2619 2620
ÁÁ
2624
ÁÁ
2628
ÁÁ
2639 2641
ÁÁ
2642
ÁÁ
2643
ÁÁ
2644
ÁÁ
2645 2646
ÁÁ
2647
ÁÁ
2648
ÁÁ
2649
ÁÁ
2650 2651
ÁÁ
2652
ÁÁ
2653
ÁÁ
2661 2662
ÁÁ
2663
ÁÁ
2664
ÁÁ
2664
ÁÁ
2665 2665
ÁÁ
DNC TIMEOUT CNC IN LOCAL MODE
ББББББББББББББББББББ
FCT NOT PERMITTED
ББББББББББББББББББББ
NO MEMORY ACCESS
ББББББББББББББББББББ
FILE ACTIVE FCT CURRENTLY NOT POSSIBLE
ББББББББББББББББББББ
NC RUNNING
ББББББББББББББББББББ
MONITOR/SIMULATION ACTIVE
ББББББББББББББББББББ
INVALID FILE NO
ББББББББББББББББББББ
READINGIN ACTIVE NO RESPONSE FROM AXIS PROCESSOR
ББББББББББББББББББББ
WRONG CARD
ББББББББББББББББББББ
NMI
ББББББББББББББББББББ
ABORT
ББББББББББББББББББББ
FPU ERROR ILLEGAL INSTRUCTION
ББББББББББББББББББББ
SVC WITH ERROR
ББББББББББББББББББББ
DIV. BY ZERO
ББББББББББББББББББББ
FLAG TRAP BREAKPOINT
ББББББББББББББББББББ
TRACE TRAP
ББББББББББББББББББББ
UNDEF OPCODE
ББББББББББББББББББББ
WRONG MODE IN CLOCK
ББББББББББББББББББББ
WRONG INTYPE IN CLOCK RAM ERROR
ББББББББББББББББББББ
EPROM ERROR
ББББББББББББББББББББ
WATCHDOG ERROR
ББББББББББББББББББББ
P2 INIT ERROR
ББББББББББББББББББББ
WRONG MODE IN LOOP VOLTAGE ERROR HSI/O
ББББББББББББББББББББ
INTERPOLATOR ABORT *
ББББББББББББББББББББ
DISTANCEENCODED MEASURING SYSTEM *
ББББББББББББББББББББ
AXIS MONITORING * NO PANEL TRANSFER
ББББББББББББББББББББ
MTB I/O BOARD MISSING
ББББББББББББББББББББ
GRAPHIC BOARD MISSING
ББББББББББББББББББББ
INVALID GRAPHIC PARAMETERS
ББББББББББББББББББББ
GRAPHICS HARDWARE ERROR UART ERROR PANEL
ББББББББББББББББББББ
CLOCK POWERFAIL
ББББББББББББББББББББ
NC INTERFACE ERROR
ББББББББББББББББББББ
GRAPHIC INTERFACE ERROR
ББББББББББББББББББББ
MTB I/OCOUPL. FAULTY ERROR IN COMMAND
ББББББББББББББББББББ
PANEL NOT PRESENT
ББББББББББББББББББББ
NC NOT PRESENT
ББББББББББББББББББББ
UART OVERRUN ERROR OVERFLOW READ FIELD
ББББББББББББББББББББ
UART: ILL. COMMAND
ББББББББББББББББББББ
BUFFER BATTERY EMPTY
ББББББББББББББББББББ
CP/MEM BATTERY VOLAGE TOO LOW
ББББББББББББББББББББ
VOLTAGE FAILURE MACHINE VOLTAGE FAILURE 1ST I/O *
ББББББББББББББББББББ
1 - 12
Page 4 - 3
4 - 3/5 - 48
БББББББ
4 - 3
БББББББ
4 - 3/5 - 48
БББББББ
4 - 3 4 - 3
БББББББ
4 - 3/5 - 48
БББББББ
4 - 4
БББББББ
4 - 4/5 - 48
БББББББ
4 - 4 2 - 2
БББББББ
2 - 2
БББББББ
2 - 2
БББББББ
2 - 2
БББББББ
2 - 2 2 - 2
БББББББ
2 - 2
БББББББ
2 - 3
БББББББ
2 - 3 2 - 3
БББББББ
2 - 3
БББББББ
2 - 3
БББББББ
2 - 3
БББББББ
2 - 3 2 - 3
БББББББ
2 - 3
БББББББ
2 - 3
БББББББ
2 - 4
БББББББ
2 - 4 2 - 4
БББББББ
2 - 4
БББББББ
2 - 4
БББББББ
2 - 4 8 - 1
БББББББ
8 - 1
БББББББ
8 - 1
БББББББ
8 - 1
БББББББ
8 - 2 8 - 2
БББББББ
8 - 2
БББББББ
8 - 2
БББББББ
8 - 2
БББББББ
8 - 2 8 - 2
БББББББ
8 - 2
БББББББ
8 - 2
БББББББ
3 - 1 3 - 1
БББББББ
3 - 1
БББББББ
3 - 1
БББББББ
3 - 1
БББББББ
3 - 1 3 - 1
БББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 2666
2667
ÁÁ
2668
ÁÁ
2669
ÁÁ
2670
ÁÁ
2671
ÁÁ
2672 2672
ÁÁ
2673
ÁÁ
2674
ÁÁ
2675
ÁÁ
2676 2677
ÁÁ
2677
ÁÁ
2678
ÁÁ
2679
ÁÁ
2680
ÁÁ
2681 2686
ÁÁ
2998
ÁÁ
3001
ÁÁ
3009
ÁÁ
3111
ÁÁ
3395 3540
ÁÁ
3541
ÁÁ
3549
ÁÁ
4639
ÁÁ
4640
ÁÁ
4641 4642
ÁÁ
4644
ÁÁ
4645
ÁÁ
4648
ÁÁ
4649
ÁÁ
4650 4651
ÁÁ
4652
ÁÁ
4653
ÁÁ
4654
ÁÁ
4658
ÁÁ
4659 4660
ÁÁ
4662
ÁÁ
4663
ÁÁ
4664
ÁÁ
4665 4666
ÁÁ
4667
ÁÁ
4668
ÁÁ
4669
UART FRAMING ERROR PLC RAM ERROR
ББББББББББББББББББББ
PLC PROGRAM < 2MS
ББББББББББББББББББББ
PLC TIMING ERROR
ББББББББББББББББББББ
PLC TIMEOUT
ББББББББББББББББББББ
UART PARITY ERROR
ББББББББББББББББББББ
TSU: ILLEGAL CHANNEL NUMBER RAM PARITY ERROR
ББББББББББББББББББББ
OVERFLOW KEYDAT
ББББББББББББББББББББ
OVERFLOW POTINDAT
ББББББББББББББББББББ
OVERFLOW MTBINDAT
ББББББББББББББББББББ
OVERFLOW CLOCKDAT PC DUAL PORT BATTERY EMPTY
ББББББББББББББББББББ
WC BATTERY EXHAUSTED
ББББББББББББББББББББ
CHANNEL NOT OPEN
ББББББББББББББББББББ
MEMORY DESTROYED
ББББББББББББББББББББ
UART ERROR 20 *
ББББББББББББББББББББ
VOLTAGE FAILURE 2ND I/O * NO RAM WRITE PROTECTION *
ББББББББББББББББББББ
ILL. PARAM IN UTILITY
ББББББББББББББББББББ
RADIUS TOO SMALL
ББББББББББББББББББББ
KS ACCESS *
ББББББББББББББББББББ
SAFETY CUTOUT
ББББББББББББББББББББ
SPINDLE STOP TOOL MAGAZINE *
ББББББББББББББББББББ
MANUAL CHANGE NOT PERMITTED *
ББББББББББББББББББББ
EDGE NOT RECOGNIZED *
ББББББББББББББББББББ
DNC APPLIED SEVERAL TIMES
ББББББББББББББББББББ
DNC INIT ERROR
ББББББББББББББББББББ
DNC HARDWARE ERROR BAB: ADDRESS ERROR
ББББББББББББББББББББ
BAB: NO CENTRAL CONTROL UNIT
ББББББББББББББББББББ
DNC INTERFACE MISSING
ББББББББББББББББББББ
DNC: MEMORY BLOCKED
ББББББББББББББББББББ
DNC: MEMORY FULL
ББББББББББББББББББББ
BAB: CRC ERROR TSUBAB BLOCKED
ББББББББББББББББББББ
ADDRESS 0 SET
ББББББББББББББББББББ
BAB STATUS PORT
ББББББББББББББББББББ
UNDEF. A IDU (INTERNAL)
ББББББББББББББББББББ
BAB: USER NOT READY
ББББББББББББББББББББ
PLC JOB KS DATA KS SEND TAB BLOCKED
ББББББББББББББББББББ
OVERFLOW TA TABLE
ББББББББББББББББББББ
TSU: IDU FAULTY
ББББББББББББББББББББ
TSU: REC. TELEGRAM TOO LONG
ББББББББББББББББББББ
TSU: REC. SEQUENCE NO. TSU: SEND SEQUENCE NO.
ББББББББББББББББББББ
TSU: INVALID TSUOPC
ББББББББББББББББББББ
TSU: SENDING BLOCKED
ББББББББББББББББББББ
TSU: SEND RESET
1 - 13
Page 3 - 1
3 - 1
БББББББ
3 - 1
БББББББ
3 - 2/5 - 49
БББББББ
3 - 2
БББББББ
3 - 2
БББББББ
6 - 12 3 - 2
БББББББ
3 - 2
БББББББ
3 - 2
БББББББ
3 - 2
БББББББ
3 - 3 7 - 15
БББББББ
7 - 15
БББББББ
3 - 3
БББББББ
3 - 3
БББББББ
3 - 3
БББББББ
3 - 3 7 - 15
БББББББ
7 - 15
БББББББ
5 - 49
БББББББ
7 - 15
БББББББ
7 - 15
БББББББ
7 - 15 4 - 4
БББББББ
4 - 4
БББББББ
7 - 15
БББББББ
7 - 16
БББББББ
7 - 16
БББББББ
4 - 5/7 - 16/6 - 12 4 - 4
БББББББ
4 - 4
БББББББ
7 - 16
БББББББ
7 - 16
БББББББ
7 - 16
БББББББ
4 - 4 4 - 4
БББББББ
7 - 16
БББББББ
4 - 5
БББББББ
4 - 5
БББББББ
4 - 5
БББББББ
4 - 5 4 - 5
БББББББ
4 - 5
БББББББ
4 - 5
БББББББ
4 - 5
БББББББ
4 - 5 4 - 5
БББББББ
4 - 5
БББББББ
4 - 6
БББББББ
4 - 6
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 4670
4671
ÁÁ
4672
ÁÁ
4682
ÁÁ
4691
ÁÁ
4693
ÁÁ
4695 4698
ÁÁ
4700
ÁÁ
4701
ÁÁ
4708
ÁÁ
4709 4710
ÁÁ
4711
ÁÁ
4713
ÁÁ
4714
ÁÁ
4715
ÁÁ
4716 4717
ÁÁ
4718
ÁÁ
4719
ÁÁ
4720
ÁÁ
4721
ÁÁ
4722 4723
ÁÁ
4724
ÁÁ
4725
ÁÁ
4726
ÁÁ
4733
ÁÁ
4734 4735
ÁÁ
4737
ÁÁ
4739
ÁÁ
4740
ÁÁ
4750
ÁÁ
4751 4752
ÁÁ
4753
ÁÁ
4754
ÁÁ
4754
ÁÁ
4760
ÁÁ
4761 4763
ÁÁ
4778
ÁÁ
4804
ÁÁ
4805
ÁÁ
4810 4811
ÁÁ
4812
ÁÁ
4813
ÁÁ
4814
TSU: RECEIVE RESET TSU: RESTART
ББББББББББББББББББББ
TSU: INVALID CHANNEL NUMBER
ББББББББББББББББББББ
INDIVIDUAL DISABLE ACTIVE
ББББББББББББББББББББ
FUNCTION BLOCKED BY PLC
ББББББББББББББББББББ
ERROR PENDING IN CNC
ББББББББББББББББББББ
FUNCTION ALREADY ACTIVE * WRONG PROGRAM
ББББББББББББББББББББ
DNC AUTO: NO BLOCKS
ББББББББББББББББББББ
NO PLC ACKNOWLEDGEMENT
ББББББББББББББББББББ
READINGIN: FILE STRUCTURE
ББББББББББББББББББББ
READINGIN: PROTOCOL ERROR OUTPUT: PROTOCOL ERROR
ББББББББББББББББББББ
FILE I/O UTILITY ERROR
ББББББББББББББББББББ
OUTPUT ABORT: COMPUTER
ББББББББББББББББББББ
READINGIN ABORT: COMPUTER
ББББББББББББББББББББ
READINGIN: WRONG FILE
ББББББББББББББББББББ
DATA AFTER FILE END NO ACCESS TO DNC RAM
ББББББББББББББББББББ
TELEGRAM CODE UNKNOWN
ББББББББББББББББББББ
LINK FAULTY
ББББББББББББББББББББ
COMPUTER NOT READY TO RECEIVE
ББББББББББББББББББББ
DNC UNDEF ERROR CODE V24
ББББББББББББББББББББ
TELEGRAM TOO LONG CLEAR FILE ERROR
ББББББББББББББББББББ
PLC NOT INITIALIZED
ББББББББББББББББББББ
PLC DATA TRANSFER
ББББББББББББББББББББ
PLC SEND TELEGRAM
ББББББББББББББББББББ
PLC BLOCKING RECEPTION
ББББББББББББББББББББ
OUTPUT REFUSED/COMPUTER READINGIN REFUSED/COMPUTER
ББББББББББББББББББББ
DNC CONTROL RESET BY COMPUTER
ББББББББББББББББББББ
PROTOCOL ERROR
ББББББББББББББББББББ
ACKNOWLEDGE DNC MESSAGES
ББББББББББББББББББББ
STATUS TRANSFER IMPOSSIBLE
ББББББББББББББББББББ
NO STATUS MESSAGE NO OPERATION MESSAGE
ББББББББББББББББББББ
MZA RECORDING
ББББББББББББББББББББ
STATUS TRANSFER
ББББББББББББББББББББ
DATA BLOCK W/O DATA
ББББББББББББББББББББ
BLOCK TRANSFER ACTIVE
ББББББББББББББББББББ
SYNTAX ERROR AUTO ABORT: COMPUTER
ББББББББББББББББББББ
INVALID BAUD RATE
ББББББББББББББББББББ
KS ACCESS BLOCKED
ББББББББББББББББББББ
KS DATA CORRUPT
ББББББББББББББББББББ
KS DEF.: TEXT LENGTH KS DEF.: NUMBER OF GROUPS
ББББББББББББББББББББ
KS DEF.: ADDRESSES
ББББББББББББББББББББ
KS DEF.: STATUS TEXT
ББББББББББББББББББББ
KS DEF.: GROUP TEXT
1 - 14
Page 4 - 6
4 - 6
БББББББ
4 - 6
БББББББ
4 - 6
БББББББ
4 - 6
БББББББ
4 - 6
БББББББ
4 - 6/5 - 49 4 - 6/5 - 49
БББББББ
7 - 16
БББББББ
7 - 16
БББББББ
4 - 7
БББББББ
4 - 7 4 - 7
БББББББ
4 - 7
БББББББ
4 - 7
БББББББ
4 - 7
БББББББ
4 - 8
БББББББ
4 - 8 4 - 8/7 - 16
БББББББ
4 - 8
БББББББ
4 - 8
БББББББ
4 - 9
БББББББ
4 - 9
БББББББ
4 - 9 4 - 9
БББББББ
4 - 9
БББББББ
4 - 9
БББББББ
4 - 9
БББББББ
4 - 9
БББББББ
7 - 17 7 - 17
БББББББ
4 - 9
БББББББ
4 - 10
БББББББ
4 - 10
БББББББ
4 - 10
БББББББ
4 - 10 4 - 10
БББББББ
4 - 10
БББББББ
7 - 17
БББББББ
4 - 10
БББББББ
4 - 10
БББББББ
4 - 10 4 - 10
БББББББ
7 - 17
БББББББ
4 - 11/5-49/7 - 17
БББББББ
5 - 49
БББББББ
4 - 11/5 - 49 4 - 11/5 - 50
БББББББ
4 - 11/5 - 50
БББББББ
4 - 11/5 - 50
БББББББ
4 - 11/5 - 50
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Error messages, general
CC 220 / 320
Error messages
Error number/error message 4815
4816
ÁÁ
4817
ÁÁ
4818
ÁÁ
4825
ÁÁ
4826
ÁÁ
4827 5100
ÁÁ
5101
ÁÁ
5102
ÁÁ
5103
ÁÁ
5104 5105
ÁÁ
5203
ÁÁ
5290
ÁÁ
5421
ÁÁ
5427
ÁÁ
5537 5694
ÁÁ
5695
ÁÁ
5696
ÁÁ
5697
ÁÁ
5698
ÁÁ
5699 5700
ÁÁ
5704
ÁÁ
KS DEF.: SUBTABLE KS DEF.: SYNTAX
ББББББББББББББББББББ
OUTPUT ACTIVE
ББББББББББББББББББББ
KS DEF.: SUBTABLE ADDITION
ББББББББББББББББББББ
KS SYS.: LIST MISSING
ББББББББББББББББББББ
KS SYS.: LIST EXISTS
ББББББББББББББББББББ
KS SYS.: PARAMETER MWORD MISSING
ББББББББББББББББББББ
SPEED MISSING
ББББББББББББББББББББ
FEEDRATE MISSING
ББББББББББББББББББББ
INVALID MWORD
ББББББББББББББББББББ
INVALID PITCH INVALID AXIS
ББББББББББББББББББББ
BITBUS ASYNCHRONOUS *
ББББББББББББББББББББ
BITBUS KST MISSING *
ББББББББББББББББББББ
BITBUS BUFFER FULL *
ББББББББББББББББББББ
TELEGRAM UNKNOWN *
ББББББББББББББББББББ
BITBUS ANSWER MISSING * INVALID KS ADDRESS *
ББББББББББББББББББББ
TELEGRAM FAULTY *
ББББББББББББББББББББ
BITBUS NEGATIVE ACKNOWLEDGE *
ББББББББББББББББББББ
BITBUS RAM ACCESS *
ББББББББББББББББББББ
SLAVE NOT RECEIVING *
ББББББББББББББББББББ
SLAVE NOT AVAILABLE * BITBUS DRIVER INACTIVE *
ББББББББББББББББББББ
BITBUS WAITING *
ББББББББББББББББББББ
Page 4 - 11/5 - 50
4 - 11/5 - 51
БББББББ
4 - 11
БББББББ
5 - 51
БББББББ
5 - 52/7 - 17
БББББББ
7 - 17
БББББББ
7 - 17 5 - 52
БББББББ
5 - 52
БББББББ
5 - 52
БББББББ
5 - 52
БББББББ
5 - 52 5 - 52
БББББББ
7 - 17
БББББББ
7 - 17
БББББББ
7 - 18
БББББББ
7 - 18
БББББББ
7 - 18 7 - 18
БББББББ
7 - 18
БББББББ
7 - 18
БББББББ
7 - 18
БББББББ
7 - 18
БББББББ
7 - 18 7 - 18
БББББББ
7 - 18
БББББББ
PANEL ERROR MESSAGES
БББББББББББББББББББББББ
G
БББББББББББББББББББББББ
GRAPHIC INTERFACE ERROR ENO. = XX
K
NO DATA TRANSFER TO NC INTERFACE
БББББББББББББББББББББББ
M
MTB I/O COUPLING HW ERROR DATA = XXH
N
БББББББББББББББББББББББ
NC TRANSMITTER LINE FAULTY!
БББББББББББББББББББББББ
NC INTERFACE: BI PORT ERROR (HALT) NC INTERFACE: STATUS ERROR (HALT)
БББББББББББББББББББББББ
NC INTERFACE: CRT RAM ERROR (HALT)
БББББББББББББББББББББББ
NC INTERFACE: EXTERNAL RAM ERROR (HALT)
P
БББББББББББББББББББББББ
PANEL: EXT. MEMORY ERROR AT ADDRESS = XXXX
БББББББББББББББББББББББ
PANEL INACTIVE P NO. = XX PANEL TRANSMITTER LINE FAULTY!
БББББББББББББББББББББББ
1 - 15
БББББББ
БББББББ
8 - 4
8 - 3
БББББББ
8 - 4
БББББББ
8 - 3
БББББББ
8 - 4 8 - 4
БББББББ
8 - 4
БББББББ
8 - 4
БББББББ
8 - 3
БББББББ
8 - 3 8 - 3
БББББББ
Flexible Automation
Error messages, general
1.2 Error messages sorted alphabetically
Error messages that have been added since edition D3 are marked with a star (*).
CC 220 / 320
Error messages
Error message
A
ABORT ABORT ACKNOWLEDGE DNC MESSAGES ACTIVE TABLE MISSING ADDRESS S" OR F" MISSING ADDRESS S" MISSING * ADDRESS 0 SET ADDRESS EXISTS SEVERAL TIMES * ADDRESS INVALID * ALL LINK TAB. ACTIVE ALL VARIANTS ALT. COMP. GROUP INVALID ALTERNATIVE TOOL AUTO ABORT: COMPUTER AXIS MONITORING * AXIS RUNNING
B
BAB STATUS PORT BAB: ADDRESS ERROR BAB: CRC ERROR BAB: NO CENTRAL CONTROL UNIT BAB: USER NOT READY BACKUP VERSION ACTIVE BARRIERS EXCEEDED BITBUS ANSWER MISSING * BITBUS ASYNCHRONOUS * BITBUS BUFFER FULL * BITBUS DRIVER INACTIVE * BITBUS KS TABLE MISSING * BITBUS NEGATIVE ACKNOWLEDGE * BITBUS RAM ACCESS * BITBUS WAITING * BLOCK > 127 BYTES BLOCK > 128 BYTES BLOCK NON-EXISTENT BLOCK NON-EXISTENT BLOCK TRANSFER ACTIVE BREAKPOINT REACHED BREAKPOINT BUFFER BATTERY EMPTY
C
C AXIS NOT ACTIVE CHANGE G41/42 WITH CIRCLE
Page
2 - 2 6 - 4 4 - 10 6 - 3 5 - 18 5 - 18 7 - 16 5 - 1 5 - 7/7 - 3 5 - 8 5 - 16 5 - 15/7 - 10 5 - 13 4 - 10 2 - 4 7 - 11
4 - 5 4 - 4 4 - 4 4 - 4 4 - 5 6 - 6 5 - 18 7 - 18 7 - 17 7 - 18 7 - 18 7 - 17 7 - 18 7 - 18 7 - 18 5 - 47 5 - 46 5 - 31 5 - 6/7 - 3 4 - 10 6 - 5 2 - 2 3 - 1
5 - 13 5 - 23
1 - 16
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
CHANGE TO AUTO CHANGE TO MDI CHANNEL NOT OPEN CHARACTER AREA NOT OCCUPIED CHECKSUM CUSTOMER EPROM CLEAR FILE ERROR CLEAR LOGIC CLEAR RESIDUAL DISTANCE G41/42 CLG VALUE INVALID CLOCK POWERFAIL CLOSE BRACKETS MISSING CNC IN LOCAL MODE CODE RANGE 4 NOT AVAILABLE COLLISION! COMM. STORE USED COMP. ACT. AT PROGRAM END COMP. ENTRY WITH CIRCLE COMP. CANCEL WITH CIRCLE COMP. NO. NOT DEFINED COMPUTER NOT READY TO RECEIVE COPY FILE NOT PRESENT COUPLING BOARD RESET CP/MEM BATTERY VOLTAGE TOO LOW CRITICAL SECTION NOT ENDED CUSTOM. EPROM ON CODE AREA CUSTOMER EPROM IN WRONG PLACE CUSTOMER EPROM TOO SMALL CUTTER RADIUS NOT MONITORED
D
DATA AFTER FILE END DATA BLOCK W/O DATA DEAD ZONE BLOCKED DISTANCE FROM ZERO POINT * DISTANCEENCODED MEASURING SYSTEM * DIV BY ZERO DIV. BY ZERO DIVISION BY 0 DLG MISSING DNC ACTIVE DNC APPLIED SEVERAL TIMES DNC AUTO: NO BLOCKS DNC CONTROL RESET BY COMPUTER DNC HARDWARE ERROR DNC INIT ERROR DNC INTERFACE MISSING DNC TIMEOUT DNC UNDEF ERROR CODE V24 DNC: MEMORY BLOCKED
Page 7 - 13
7 - 8 3 - 3 5 - 47 7 - 9 4 - 9 6 - 2 7 - 4 5 - 19 8 - 2 5 - 18 4 - 3/5 - 48 6 - 6 5 - 21 7 - 8 5 - 23 5 - 22 5 - 23 5 - 14 4 - 9 6 - 8 6 - 4 3 - 1 6 - 6 9 - 1 7 - 9 7 - 9 7 - 10
4 - 8 4 - 10 5 - 10 5 - 16 2 - 4 6 - 4 2 - 2 5 - 39 5 - 40 5 - 48 7 - 16 7 - 16 4 - 9 4 - 4/7 - 16/6 - 9 7 - 16 7 - 16 4 - 3 4 - 9 7 - 16
1 - 17
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
DNC: MEMORY FULL DO MISSING DRIVE ON ERROR DSP FORMAT WRONG
E
E DIR. INCOMPLETE EDGE NOT RECOGNIZED * EDIT ENABLE MISSING EMERGENCY STOP PENDING ENCODER DEFECTIVE END MISSING ENDDLG MISSING ENDIF MISSING EPROM ERROR EPROM ERROR EPROM ERROR EPROM WRITE PROTECTED ERR BLOCKCON ERROR IN COMMAND ERROR IN DIAGN. PRG. ERROR IN ECODE ERROR IN FILE STRUCTURE ERROR IN NC BLOCK ERROR IN PLC PROGRAM ERROR IN USER HEAP ERROR PENDING IN CNC ERROR LSEC FILE PROCESSING ERROR: DUAL PORT TEST ERROR: P2 INIT ERROR: PARTY LINE TEST ERROR: RAM TEST ERROR: RELOAD TEXT
F
F NOT PREALLOCATED FALSE PARAMETER IDENTIFIER FCT CURRENTLY NOT POSSIBLE FCT NOT PERMITTED FEED NOT PERMITTED FEED OVERRIDE TABLE MISSING FEEDRATE MISSING FILE ACTIVE FILE ALREADY EXISTS * FILE DESTROYED FILE NONEXISTENT FILE END REACHED FILE GROUP NOT DEFINED (OPEN AND CLOSE) FILE HAS DFS IDENTIFIER FILE I/O UTILITY ERROR
Page 7 - 16
5 - 26 5 - 12 7 - 12
7 - 8 7 - 15 4 - 1/7 - 4 2 - 1 2 - 2 5 - 26 5 - 40 5 - 26 2 - 3 4 - 3 6 - 6 7 - 7 6 - 6 8 - 2 7 - 4 5 - 20/7 - 11 4 - 1/5 - 6/7 - 2 5 - 38 5 - 11 6 - 8 4 - 6 6 - 7 6 - 5 6 - 6 6 - 5 6 - 5 6 - 5
7 - 4 5 - 14 4 - 3 4 - 3 5 - 17 7 - 9 5 - 52 4 - 3 4 - 2/7 - 11/5 - 18 5 - 8 5 - 18/7 - 11 5 - 44 6 - 7 7 - 4 4 - 7
1 - 18
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
FILE IN LIBRARY * FILE IN USE * FILE IS ACTIVE FILE LENGTH INVALID FILE NAME FAULTY FILE NAME INVALID * FILE NONEXISTENT FILE NOT DELETABLE FILE NOT OPENED FILE PROTECTED FILE TRANSFER ERROR FILE TRANSFER ERROR FLAG TRAP FLAG TRAP FORMAT ERROR * FORMAT NOT AGREED FPU ERROR FPU TRAP FUNCTION ALREADY ACTIVE * FUNCTION BLOCKED BY PLC
G
G ADDR. INVALID FOR G41/42 G108 ACTIVE * G14 WITHOUT AXIS INFO G2/3: F/R INVALID G2/3: INVALID NUMBER OF AXES G33: LEAD NOT PERMITTED G33: RETRACTION NOT PERMITTED G5: AFTER HELICAL G5: AFTER LEVEL CHANGE G5: DIRECTION UNDEFINED G5: RADIUS TOO LARGE G6 W/O AXIS INFO * G92 IS ACTIVE * G92 OR ZERO SHIFT GROUP CHANGED G92 X.. NOT PERMITTED GRAPHIC BOARD MISSING GRAPHIC INTERFACE ERROR GRAPHICS ALREADY ACTIVE GRAPHICS HARDWARE ERROR
H
H WITHOUT TRAVERSING INFO HEAP OVERFLOW HEAP OVERFLOW
I
I/O DEVICE TIMEOUT ILL. PARAM IN UTILITY ILLEGAL INSTRUCTION
Page 4 - 2/5 - 11/7 - 8
5 - 45 7 - 11 5 - 45 5 - 9 5 - 46 5 - 43/4 - 2 5 - 8 5 - 44 4 - 1/5 - 9/7 - 7 4 - 2/6 - 9 6 - 2 2 - 2 6 - 5 5 - 2 6 - 7 2 - 2 6 - 4 4 - 6/5 - 49 4 - 6
5 - 23 5 - 16 5 - 19 5 - 19 5 - 19 5 - 16 5 - 16 5 - 19 5 - 20 5 - 19 5 - 19 5 - 10 5 - 12 5 - 13 5 - 15 8 - 1 8 - 2 7 - 13 8 - 2
5 - 10 6 - 5 7 - 14
5 - 7/7 - 3 7 - 15 2 - 2
1 - 19
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
ILLEGAL MEMORY ACCESS ILLEGAL OPERAND ILLEGAL PARAMETER IN UTILITY INADMISSIBLE AVALUE INADMISSIBLE COMPENSATION VALUE INADMISSIBLE FILE NUMBER INADMISSIBLE VARIABLE INCORRECT CIRCULAR PATH PROGRAMMING INCORRECT INPUT INCORRECT USE OF DO-AGAIN FLAG INDIVIDUAL DISABLE ACTIVE INPUT ERROR INPUT INCORRECT, AXIS RUNNING INPUT INCORRECT INPUT INSTRUCTION DOUBLE INSUFFICIENT CHECK POINTS INSUFFICIENT MEMORY INTERFACE INVALID INTERNAL INTERPOLATOR ABORT INVALID ASIN ACOS INVALID ASSIGNMENT INVALID AXIS INVALID BAUD RATE INVALID CVALUE * INVALID CHANGE POSITION INVALID CHARACTER * INVALID CHECK POINT INVALID CIRCLE PARAMETER INVALID COMPENSATION VALUE INVALID COMPENSATION VALUE INVALID COMPONENT LENGTH INVALID COMPONENT INVALID DISTURBANCE TABLE INVALID E WORD INVALID EXPRESSION INVALID FIELD INDEX INVALID FIELD LIMIT INVALID FIELD TYPE INVALID FILE GROUP INVALID FILE NO * INVALID FILE INVALID FORMAT INVALID G CODE INVALID GRAPHIC PARAMETERS INVALID H WORD INVALID INTEGER INVALID KS ADDRESS *
Page 6 - 8
6 - 4 6 - 9 5 - 10 6 - 3 5 - 8 5 - 27 5 - 10 7 - 1 6 - 6 4 - 6 5 - 1/7 - 1 5 - 8 5 - 1/7 - 1 5 - 43 5 - 12 5 - 24/7 - 13 5 - 45 7 - 14 2 - 4 5 - 39 5 - 30 5 - 52 7 - 17 5 - 10 5 - 15 5 - 1 5 - 13 5 - 19 5 - 9 5 - 22 7 - 14 7 - 14 7 - 7 5 - 10 5 - 29 5 - 32 5 - 32 5 - 32 4 - 1/5 - 9 4 - 4/5 - 48 5 - 47 5 - 2/7 - 1 5 - 12 8 - 1 5 - 10 5 - 48 7 - 18
1 - 20
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
INVALID LABEL INVALID LEVEL* INVALID LIMIT POSITION INVALID MWORD INVALID OPERAND INVALID PARAMETER INVALID PC COMMAND INVALID PC OPERAND INVALID PERMVARIABLE INVALID PITCH INVALID POINTER WHEN CLOSING FILE INVALID PROGR. IDENTIFIER INVALID PROGRAMMING INVALID REAL VALUE * INVALID REAL VALUE INVALID RELATION INVALID STATEMENT INVALID STRING/TRANSFER ERROR INVALID TAN INVALID TANGENT INVALID TOOL CALL INVALID TURNING TOOL INVALID VALUE INVALID WEIGHTING FACTOR INVALID WORKING AREA INVALID X ZERO SHIFT INVALID ZERO OFFSET GROUP IS MAIN BLOCK SEARCH WANTED?
K
KS ACCESS * KS ACCESS BLOCKED KS DATA CORRUPT KS DEF.: ADDRESSES KS DEF.: GROUP TEXT KS DEF.: NUMBER OF GROUPS KS DEF.: STATUS TEXT KS DEF.: SUBTABLE ADDITION KS DEF.: SUBTABLE KS DEF.: SYNTAX KS DEF.: TEXT LENGTH KS SEND TAB BLOCKED KS SYS.: LIST EXISTS KS SYS.: LIST MISSING KS SYS.: PARAMETER KS-DEF. PART DESTROYED *
L
LABEL NONEXISTENT LEAD TOO LARGE
Page 5 - 38
5 - 18 5 - 10 5 - 52 5 - 30 5 - 33 7 - 7 7 - 7 5 - 37 5 - 52 6 - 8 5 - 15 5 - 12 5 - 40 6 - 3 5 - 30 5 - 25 5 - 14 5 - 39 6 - 3 5 - 15 5 - 15 5 - 48/7 - 14 5 - 19 5 - 13 5 - 13 5 - 9 6 - 3
7 - 15 4 - 11/5-49/7 - 17 5 - 49 4 - 11/5 - 50 4 - 11/5 - 50 4 - 11/5 - 50 4 - 11/5 - 50 5 - 51 4 - 11/5 - 50 4 - 11/5 - 51 4 - 11/5 - 49 4 - 5 7 - 17 5 - 52/7 - 17 7 - 17 6 - 2
5 - 32 5 - 20
1 - 21
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
LEVEL CHANGE ACT. COMP. LIMIT POSITION WRONGLY CALCULATED LIMIT SWITCH 1ST AXIS LIMIT SWITCH 2ND AXIS LIMIT SWITCH 3RD AXIS LIMIT SWITCH 4TH AXIS LIMIT SWITCH 5TH AXIS LIMIT SWITCH 6TH AXIS LIMIT SWITCH 7TH AXIS LIMIT SWITCH 8TH AXIS LIMIT SWITCH LIMIT SWITCH LINE NONEXISTENT LINK ERROR LINK FAULTY LINK TABLE NOT PRESENT LINKING ABORTED LINKING ALREADY ACTIVE LOAD COMP. TABLE LOG NUMBER INVALID LSEC FILE DEFECTIVE LSEC GRID LSEC LOGIC LSEC OVERFLOW LSEC SYNTAX LSV2 STATUS DATA FAULT
M
MWORD MISSING M30 WITH ACT. SYNC. * MACHINE PARAMETERS MISSING MACRO ADDRESS NOT PRESENT FOR RESET MAILBOX FULL MANUAL CHANGE NOT PERMITTED * MARKER MISSING MAX. SUBROUTINE DEPTH MAXIM. 4 CLAWS MEASURING SYSTEM FAULTY MEMORY DESTROYED MEMORY FULL MEMORY FULL MEMORY FULL MEMORY IS OCCUPIED MEMORY OVERFLOW MODAL SUBROUTINE IS ACTIVE MONITOR/SIMULATION ACTIVE MSG NOT PRESENT FOR OUTPUT MTB I/O BOARD MISSING MTB I/OCOUPL. FAULTY
Page 5 - 21
5 - 10 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 5 - 9/7 - 6 2 - 1 5 - 7 5 - 32 5 - 8/7 - 5 4 - 8 5 - 11/7 - 8 7 - 5 5 - 8 5 - 11 5 - 44 6 - 7 7 - 6 7 - 5 7 - 6 7 - 5 6 - 8
5 - 52 5 - 17 9 - 1 6 - 6 7 - 4 4 - 4 2 - 1 5 - 4 5 - 11 2 - 1 3 - 3 4 - 1 4 - 1/5 - 5/7 - 2 5 - 10 5 - 24/7 - 12 7 - 9 5 - 24 4 - 4 6 - 6 8 - 1 8 - 2
1 - 22
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
MULTIPLE SUBROUTINE PROHIBITED MZA RECORDING
N
NC INTERFACE ERROR NC NOT PRESENT NC RUNNING NEGATIVE ROOT NEGATIVE ROOT NESTING TOO DEEP NEXT MISSING NMI NMI NO ACCESS TO DNC RAM NO ALT. TOOL NO AXIS COUPLING POSSIBLE * NO COMPENSATION ACTIVE NO COMPENSATION GROUP ACTIVE NO CONTROL RESET POSSIBLE NO DIAG. START POSSIBLE NO DISTURBANCE TABLE NO E WORD PROGRAMMED NO G96 POSSIBLE NO INTERROGATION NO INTERSECTION NO LZ VALUE NO M02 OR M30 NO MEMORY ACCESS NO OPERATION MESSAGE NO PANEL TRANSFER NO DIST. PROGRAMMED NO PLC ACKNOWLEDGEMENT NO RAM WRITE PROTECTION NO REF. POINTS NO RESPONSE FROM AXIS PROCESSOR NO RUNTIME MEMORY NO RXR BIT FOR PANEL INTERRUPT NO STATUS MESSAGE NO TOOL ACTIVE
O
OLD LANGUAGE VERSION OPTIMIZATION BUFFER FULL OSCILLATING AXIS ACTIVE OUTPUT ACTIVE OUTPUT REFUSED/COMPUTER OUTPUT: ABORT COMPUTER OUTPUT: PROTOCOL ERROR OVERFLOW CLOCKDAT OVERFLOW KEYDAT
Page 5 - 37
4 - 10
8 - 2 8 - 2 4 - 3/5 - 48 5 - 39 6 - 3 5 - 25 5 - 26 2 - 2 6 - 4 4 - 8/7 - 16 7 - 9 5 - 20 5 - 23 5 - 15 7 - 6 7 - 14 7 - 7 5 - 10 5 - 17 6 - 3 5 - 22 5 - 14 5 - 24/7 - 12 4 - 3/5 - 48 4 - 10 8 - 1 5 - 17 7 - 16 7 - 15 4 - 1/7 - 3 2 - 2 5 - 8 6 - 4 4 - 10 5 - 15
7 - 8 7 - 9 5 - 12 4 - 11 7 - 17 4 - 7 4 - 7 3 - 3 3 - 2
1 - 23
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
OVERFLOW MTBINDAT OVERFLOW POTINDAT OVERFLOW READ FIELD OVERFLOW TA TABLE
P
P NOT IN CALLCHAIN P2 INIT ERROR PANEL NOT PRESENT PANEL NOT SUITABLE PARAMETER ERROR PARITY PC DUAL PORT BATTERY EMPTY PC PROGRAM TOO LARGE PERMITTED VALUE RANGE EXCEEDED PERM. VARIABLE BLOCKED PLC BATTERY EMPTY PLC BLOCKING RECEPTION PLC DATA TRANSFER PLC FM INCORRECT PLC FM TIMEOUT PLC JOB KS DATA PLC NOT INITIALIZED PLC PROGRAM < 2MS PLC RAM ERROR PLC SEND TELEGRAM PLC TIMEOUT PLC TIMING ERROR PLEASE ENABLE MEMORY POINTER IN THE LIST OR TREE MANAGEMENT DESTROYED POSITION ERROR PRN INSTRUCTION MISSING PRN INVALID PROFILE NONEXISTANT PROGRAM ACTIVE PROGRAM IN CONTROL PROGRAM ACTIVE * PROGRAM ACTIVE PROGRAM MEMORY DESTROYED! * PROGRAM NOT PRESENT PROHIB. WORKING AREA AXIS 1 PROHIB. WORKING AREA AXIS 2 PROHIB. WORKING AREA AXIS 3 PROHIB. WORKING AREA AXIS 4 PROHIB. WORKING AREA AXIS 5 PROHIB. WORKING AREA AXIS 6 PROHIB. WORKING AREA AXIS 7 PROHIB. WORKING AREA AXIS 8 PROHIB. WORKING AREA CIRCLE
Page 3 - 2
3 - 2 3 - 1 4 - 5
7 - 13 2 - 3 8 - 2 7 - 4 5 - 38 5 - 7 7 - 15 7 - 8 5 - 14 5 - 20 7 - 7 4 - 9 4 - 9 7 - 8 7 - 8 4 - 5 4 - 9 3 - 1 3 - 1 4 - 9 3 - 2 3 - 2/5 - 49 7 - 12 6 - 8 2 - 1 5 - 43 5 - 43 7 - 10 4 - 1 7 - 2 7 - 10 7 - 3 6 - 8 7 - 1 5 - 20 5 - 20 5 - 20 5 - 20 5 - 20 5 - 20 5 - 20 5 - 20 5 - 20
1 - 24
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
PROHIB. WORKING AREA PROTECTION FAULTY PROTOCOL ERROR
R
RADIUS > 5000 MM RADIUS TOO SMALL RAM ECHO ERROR IN PLSINI RAM ERROR RAM PARITY ERROR RANGE EXCEEDED RANGE NOT PRESENT READINGIN ACTIVE READINGIN REFUSED/COMPUTER READINGIN: ABORT COMPUTER READINGIN: FILE STRUCTURE READINGIN: PROTOCOL ERROR READINGIN: WRONG FILE REAL NUMBER OVERFLOW REMOTE DIAGNOSIS ACTIVE RESTART ERROR RETRACTION NOT POSSIBLE
S
SAFETY CUTOUT SELFCALL PROHIBITED SERVO ERROR SEVERAL ZERO SHIFTS ACTIVE SIGN ERROR SIMULATION MEMORY FULL SINGLE BLOCK WITH G41/42 SLAVE NOT AVAILABLE * SLAVE NOT RECEIVING * SOFTKEY PARAMETER < 0 SPEED MISSING SPINDLE INTERF. ERROR * SPINDLE PROG. INVALID * SPINDLE SPEED NOT PERMITTED SPINDLE STOP SQRT OF NEG. ARGUMENT STACK OVERFLOW STACK SUBRANGE EXHAUSTED STARTED BY CENTRAL CONTROL UNIT ONLY STARTING NOT POSSIBLE STATUS TRANSFER IMPOSSIBLE STATUS TRANSFER SUBROUTINE CALL MISSING SUBROUTINE NONEXISTENT * SVC NO. 6 SVC TRAP
Page 5 - 40
5 - 9 4 - 10
5 - 19 5 - 49 6 - 4 2 - 3 3 - 2 5 - 46 5 - 47 4 - 4 7 - 17 4 - 7 4 - 7 4 - 7 4 - 8 5 - 47 7 - 15 4 - 2 5 - 16
7 - 15 5 - 25 2 - 1 5 - 22 5 - 4 7 - 9 5 - 23 7 - 18 7 - 18 6 - 7 5 - 52 5 - 17 5 - 17 5 - 16 7 - 15 6 - 6 6 - 9 6 - 8 7 - 14 5 - 12 4 - 10 7 - 17 7 - 11 5 - 24 6 - 5 6 - 4
1 - 25
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
SVC WITH ERROR SWITCHOVER NOT PERMITTED SYNCHR. NOT POSSIBLE * SYNTAX ERROR
T
T TABLE RENAMED T WITH ACTIVE G491 TABLE CHANGE WITH ACTIVE G491 TABLE IS ACTIVE TABLE NOT ACCEPTED TABLE NOT CREATED TABLE NOT PRESENT TAP TOO SMALL TASK END WITHOUT STOP TASK MISSING IN NOTQ TASK STILL ACTIVE TASK TRANSFER IMPOSSIBLE TELEGRAM CODE UNKNOWN TELEGRAM FAULTY * TELEGRAM TOO LONG TELEGRAM UNKNOWN * TEST ACTIVE TEXT FILE MISSING THEN MISSING TIME TO BE SET TIMEOUT BY WAIT FOR P2 TIMEOUT WHILE WAIT FOR P2 TIMING ERROR IN PLSINI TIMING ERROR IN WAITFORRXR TO MISSING TOO MANY AXIS MOVEMENTS TOO MANY BLOCKS SUPPRESSED TOO MANY VARIABLES TOOL CHANGE ACKNOWLEDGEMENT TOOL CHANGE ONLY WITH G40 TOOL DATA W1-W4 MISSING TOOL MAGAZINE * TOOL NO. NOT DEFINED TRACE TRAP TRACE TRAP TSUBAB BLOCKED TSU: IDU FAULTY TSU: ILLEGAL CHANNEL NUMBER TSU: INVALID CHANNEL NUMBER TSU: INVALID TSUOPC TSU: REC. SEQUENCE NO. TSU: REC. TELEGRAM TOO LONG TSU: RECEIVE RESET
Page 2 - 2
5 - 11 5 - 17 4 - 10
7 - 10 5 - 14 5 - 14 7 - 3 7 - 10 7 - 13 5 - 1 5 - 10 6 - 9 6 - 8 6 - 9 6 - 9 4 - 8 7 - 18 4 - 9 7 - 18 7 - 9 9 - 1 5 - 25 5 - 8 6 - 6 7 - 14 6 - 3 6 - 3 5 - 26 7 - 5 5 - 21 5 - 24 7 - 10 5 - 15 5 - 15 4 - 4 5 - 14 2 - 3 6 - 5 4 - 4 4 - 5 6 - 9 4 - 6 4 - 5 4 - 5 4 - 5 4 - 6
1 - 26
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
TSU: RESTART TSU: SEND RESET TSU: SEND SEQUENCE NO. TSU: SENDING BLOCKED TYPE MUST BE BIT
U
UART ERROR 20 UART ERROR PANEL UART FRAMING ERROR UART OVERRUN ERROR UART PARITY ERROR UART: ILL. COMMAND UNAUTHORIZED ACCESS UNDEF OPCODE UNDEF. A IDU (INTERNAL) UNDEFINED OPCODE UNEQUAL FACTORS UNTIL MISSING UPGRADE LEVEL INACTIVE
V
V.24 COMMAND ERROR V.24 ERROR USER A V.24 INIT ERROR V.24 INTERRUPTION USER A V.24 OVERFLOW USER A V.24 PARITY USER A V.24 PROTOC. ERROR USER A V.24 RAM1 ERROR V.24 RAM2 ERROR VARIABLE NOT OCCUPIED VARIABLE TYPE WRONG VOLTAGE ERROR HS-I/O VOLTAGE FAILURE 1ST I/O VOLTAGE FAILURE 2ND I/O VOLTAGE FAILURE MACHINE I/O
W
WATCHDOG COUNTER P2 NOT RUNNING WATCHDOG ERROR WC BATTERY EXHAUSTED WEAR WORKING AREA MAX. 3 AXES WRONG BRANCH DESTINATION WRONG CARD WRONG CODE NUMBER WRONG COM FORMAT WRONG DIAG. VERSION WRONG INDEX
WRONG INPUT FORMAT
Page 4 - 6
4 - 6 4 - 5 4 - 6 5 - 30
3 - 3 8 - 2 3 - 1 3 - 1 3 - 2 3 - 1 5 - 47 2 - 3 4 - 5 6 - 5 5 - 20 5 - 26 4 - 1/5 - 4/7 - 2
4 - 3 4 - 2 7 - 15
4 - 2 4 - 2 4 - 2 4 - 3 4 - 3 5 - 25 5 - 24 2 - 3 3 - 1 3 - 3 3 - 1
6 - 2 2 - 3 7 - 15 7 - 9 5 - 20 5 - 26 2 - 2 7 - 4 5 - 47 7 - 4 5 - 25
5 - 40
1 - 27
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
Error message
WRONG INTERRUPT PCB WRONG INTYPE IN CLOCK WRONG MODE IN CLOCK WRONG MODE IN LOOP WRONG MODE IN READ WRONG PRINT FORMAT WRONG PROGRAM WRONG SOFTKEY FORMAT WRONG TOOL TYPE WRONG USE OF OPTIONS
Z
ZERO OFFSET NOT APPROACHED ZERO SHIFT OR COMP. CHANGE IN G491
" MISSING ( MISSING ) MISSING +X SIDE WRONG (MPP 7513)
- NOT PERMITTED
-X SIDE WRONG (MPP 7513) = MISSING ] MISSING
Page 6 - 4
2 - 3 2 - 3 2 - 3 6 - 7 5 - 41 4 - 6/5 - 49 5 - 43/7 - 13 7 - 7 6 - 9
5 - 16 5 - 13
5 - 37 5 - 31 5 - 28 5 - 13 5 - 29 5 - 13 5 - 26 5 - 31
1 - 28
Flexible Automation
1.3 Abbreviations
Error messages, general
CC 220 / 320
Error messages
ADR
BABNET BACKUP BPT CR / LF CLM COM CTR
DA DFS DLG DNC
EOF ETX EXP ERR
FSI FPU
ADDRESS
BOSCH SYSTEM BUS NETWORK LOADING BACK THE OPERATING SYSTEM BREAKPOINT ENDOFBLOCK IDENTIFIER CLEAR MEMORY COMMUNICATION MEMORY CONTROL RESET
DIRECT EXECUTION (VIA DNC INTERFACE) DEFINE STORAGE DIALOG DIRECT NUMERICAL CONTROL
END OF FILE ENDOFFILE IDENTIFIER EXECUTE EXTERNAL PROGRAM ERROR
FILE STORAGE IDENTIFICATION FLOATING POINT UNIT
GBA GRA
HEAP HP HS HW HW RESET
IF ILL IDU
KS
LF LSV2 LSV2-DNC LR LSEC
MDI MP MPP
GROUP OPERATING MODE GRAPHICS
MEMORY IN OPERATING SYSTEM MAIN PROGRAM HIGH SPEED HARDWARE HARDWARE RESET (= CLEAR LOGIC)
INTERFACE ILLEGAL JOB TYPE
COMMUNICATION MEMORY
LINE FEED DATA LINK PROTOCOL DNC WITH LSV2 PROTOCOL VIA V24/20 MA INTERFACE MASTER CONTROL COMPUTER LEADSCREW ERROR COMPENSATION
MANUAL DATA INPUT MACHINE PARAMETER MACHINE PARAMETER PROGRAM
1 - 29
Flexible Automation
Error messages, general
CC 220 / 320
Error messages
NPV
PLS PTR P
RTC RXR RXP
SK, SFK SPIL SPG SVC SW
TSU
UP
WMH
ZERO OFFSET
PANEL SOFTWARE PAPER TAPE READER PARAMETER
REALTIME CLOCK RECEIVER READY RECEIVE EXTERNAL PROGRAM
SOFTKEY SOFTWARE PROGRAMMABLE INTERFACE LOGIC SELECT PROGRAM SUPERVISOR CALL SOFTWARE
TRANSPORT LAYER
SUBROUTINE
MACHINE TOOL MANUFACTURER
1 - 30
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
2. P2 ERRORS
P2 errors
CC 300 M
Error messages
ERROR CAUSE
115 LIMIT SWITCH
Machine position outside limit switch range.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
116 SERVO ERROR
БББББББББББББББ
Overtravel too great; setpoint limit exceeded.
БББББББББББББББ
Tachogenerator interrupted. Setpoint interrupted and axis drifting.
БББББББББББББББ
БББББББББББББББ
117 MARKER MISSING
БББББББББББББББ
Number of readin increments of the encoder
БББББББББББББББ
greater than defined in the MPP and still no
БББББББББББББББ
zero pulse. Measuring system error; counted encoder
БББББББББББББББ
pulses more than one revolution but no new
БББББББББББББББ
marker.
БББББББББББББББ
Encoder cable faulty (zero pulse line inter rupted)
БББББББББББББББ
Interface on the servo l/O board faulty.
БББББББББББББББ
ERROR REMEDY
* Move axis mechanically to limit switch range
БББББББББББББББ
(permitted range);
БББББББББББББББ
* Axis optimization (check overtravel and offset).
For TR40 TC235 values X2,0; Y3,9: W8,0.
БББББББББББББББ
* Approach position more slowly (axis overshoot);
БББББББББББББББ
possibly reduce MPP P1007.
БББББББББББББББ
* Check axis mechanisms. * Set SW limit switch tolerance higher; MPP 1507:
БББББББББББББББ
> 0.050 mm.
БББББББББББББББ
БББББББББББББББ
* Control reset.
БББББББББББББББ
* Check axis mechanisms. * Remedy cause.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check encoder.
БББББББББББББББ
БББББББББББББББ
* Replace encoder cable.
БББББББББББББББ
БББББББББББББББ
* Replace subassembly.
БББББББББББББББ
118 MEASURING CIRCUIT ERROR
БББББББББББББББ
118 MEASURING SYSTEM FAULTY
Encoder signal monitoring has responded.
БББББББББББББББ
Measuring system removed or faulty.
БББББББББББББББ
БББББББББББББББ
Interface on the servo l/O board faulty.
БББББББББББББББ
139 EMERGENCYSTOP PENDING
Interface signal EMERGENCYSTOP pending.
БББББББББББББББ
БББББББББББББББ
194 POSITION ERROR
БББББББББББББББ
Number of readin increments greater than or
БББББББББББББББ
less than number of encoder lines; zero pulse
БББББББББББББББ
present.
БББББББББББББББ
Interface on the servo l/O board faulty.
БББББББББББББББ
2 - 1
БББББББББББББББ
БББББББББББББББ
* Check measuring system; clear logic.
БББББББББББББББ
БББББББББББББББ
* Replace board.
БББББББББББББББ
* Remedy cause for emergencystop; control reset
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check encoder or cable; change cables round
БББББББББББББББ
amongst each other.
БББББББББББББББ
БББББББББББББББ
* Check MPP P104.
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
P2 errors
CC 300 M
Error messages
ERROR CAUSE
196 ENCODER DEFECTIVE
Overtravel of axis at standstill too great.
БББББББББББББББ
Excessive axis drift.
БББББББББББББББ
Measuring system does not supply any
БББББББББББББББ
pulses. No axis movement, no measuring system
БББББББББББББББ
pulses.
БББББББББББББББ
Starting enable missing.
БББББББББББББББ
Motor faulty.
БББББББББББББББ
2587 NO RESPONSE FROM AXIS PROCESS
Axis processor card faulty.
БББББББББББББББ
БББББББББББББББ
2588 WRONG CARD
БББББББББББББББ
Servo card complement does not correspond
БББББББББББББББ
to entry in MPP P9501.
БББББББББББББББ
2602 NMI
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2603 ABORT
System error of the servo processor.
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
* Perform offset adjustment.
БББББББББББББББ
* Check measuring system.
БББББББББББББББ
* Coupling between motor and measuring system
БББББББББББББББ
loose?
БББББББББББББББ
* Set drive enable.
БББББББББББББББ
* Check motor.
БББББББББББББББ
* Check axis processor card and replace if
БББББББББББББББ
necessary.
БББББББББББББББ
БББББББББББББББ
* Correct entry in P9501 corresponding to servo
БББББББББББББББ
card complement.
БББББББББББББББ
БББББББББББББББ
* Replace CP card. * Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card. * Inform aftersales service.
БББББББББББББББ
2604 FPUERROR
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2605 ILLEGAL INSTRUCTION
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2606 SVC WITH ERROR
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2607 DIV. BY ZERO
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2608 FLAG TRAP
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2609 BREAKPOINT
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2 - 2
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card. * Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card. * Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
P2 errors
CC 300 M
Error messages
ERROR CAUSE
2610 TRACE TRAP
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2611 UNDEF OPCODE
БББББББББББББББ
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
2612 WRONG MODE IN CLOCK
БББББББББББББББ
Defective P2 software or dual port faulty. Mode must be set to 2". This is permanently
БББББББББББББББ
monitored by P2. If mode was switched, this
БББББББББББББББ
acts as an indication that other data may be
БББББББББББББББ
destroyed in the dual port RAM.
БББББББББББББББ
2613 WRONG INTYPE IN CLOCK
P1-P2 software versions do not match or
БББББББББББББББ
data in dual port RAM destroyed.
БББББББББББББББ
БББББББББББББББ
2614 RAM ERROR
System error of the servo processor.
БББББББББББББББ
БББББББББББББББ
ERROR REMEDY
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card. * Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Replace CP card.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
2615 EPROM ERROR
БББББББББББББББ
Defective P2 software. Error in EPROM test of processor P2.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2616 WATCHDOG ERROR
БББББББББББББББ
Computing operation of processor P1 too
БББББББББББББББ
long (defective SW).
БББББББББББББББ
БББББББББББББББ
2617 P2 INIT ERROR
Defective or wrong P2SW; Processor P2 has
БББББББББББББББ
wrong data for startup.
БББББББББББББББ
HW error on CP subassembly.
БББББББББББББББ
БББББББББББББББ
2619 WRONG MODE IN LOOP
Data in dual port RAM destroyed; dual port
БББББББББББББББ
RAM overwritten.
БББББББББББББББ
2620 VOLTAGE ERROR HSI/O
БББББББББББББББ
+24V missing for HS I/O board.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2 - 3
БББББББББББББББ
* Replace P2 software on CP subassembly. * P2 software EPROMs correctly installed?
БББББББББББББББ
* HW error on CP subassembly?
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* Control reset (clear error message).
БББББББББББББББ
* Note the last operator steps and inform the after
sales service.
БББББББББББББББ
БББББББББББББББ
* P2 software EPROMs correctly installed?
БББББББББББББББ
* Replace CP.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Reload software.
БББББББББББББББ
* Change CP.
БББББББББББББББ
БББББББББББББББ
* Check +24V on the servo l/O board.
БББББББББББББББ
* Check connector X31 on the servo l/O subas
sembly.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
P2 errors
CC 300 M
Error messages
ERROR CAUSE
2624 INTERPOLATOR ABORT
Travel command is present, but Drive on"
БББББББББББББББ
has been removed.
БББББББББББББББ
БББББББББББББББ
Travel command is present, Lock measuring system monitoring" is active via interface and
БББББББББББББББ
the measuring system is defective.
БББББББББББББББ
2628 DISTANCEENCODED MEASURING
БББББББББББББББ
SYSTEM
When using a distanceencoded measuring
БББББББББББББББ
system:
БББББББББББББББ
A marker is not found
БББББББББББББББ
 after 1 revolution with rotary transducer 
БББББББББББББББ
or the 2nd cyclic (encoded) marker is not found.
БББББББББББББББ
MPP 1514 is parameterized to distanceen
БББББББББББББББ
coded", but no distanceencoded measuring
БББББББББББББББ
system is connected.
БББББББББББББББ
2639 AXIS MONITORING
After removing the travel command, the over
БББББББББББББББ
travel limit value entered in MPP 1012 is ex
БББББББББББББББ
ceeded (after the waiting period specified in P
1013).
БББББББББББББББ
БББББББББББББББ
ERROR REMEDY
* Control reset; check PLC program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Replace measuring system.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Define MPP 1515, MPP 1517, MPP 104/105
БББББББББББББББ
accurately, possible reduce entry in MPP 502
БББББББББББББББ
(ref. point speed)
БББББББББББББББ
БББББББББББББББ
* Connect distanceencoded measuring system.
БББББББББББББББ
БББББББББББББББ
* Check entries in MPP 1012/1013.
БББББББББББББББ
* Measuring system ok?
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
2 - 4
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
3. NC ERRORS
NC errors
CC 220 / 320
Error messages
ERROR CAUSE
2661 UART OVERRUN ERR
БББББББББББББББ
Data transfer speed not correct.
БББББББББББББББ
БББББББББББББББ
2662 OVERFLOW READ FIELD
Loss of readin data.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2663 UART: ILLCOMMAND
Inadmissible programming of the UART of the
БББББББББББББББ
CNC interface (defective SW).
БББББББББББББББ
БББББББББББББББ
2664 BUFFER BATTERY EMPTY
БББББББББББББББ
The battery on the MEM board for buffering of
БББББББББББББББ
the program memory (RAM) is exhausted.
БББББББББББББББ
2664 CP/MEM BATT. VOLTAGE TOO LOW
БББББББББББББББ
The battery on the CP/MEM board for buffer ing the program memory (RAM) is exhausted.
БББББББББББББББ
БББББББББББББББ
2665 VOLTAGE FAILURE MACHINE l/O
+24 V voltage missing on l/O subassembly.
БББББББББББББББ
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
* Check baud rate.
БББББББББББББББ
* Check handshake signals.
БББББББББББББББ
* Data input device faulty? Interface on the CP
БББББББББББББББ
X11/20 mA faulty? Check interface on panel (V
БББББББББББББББ
24/20 mA).
БББББББББББББББ
* Check baud rate.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Replace battery and perform HW reset (refer to
БББББББББББББББ
Battery replacement" in Interface conditions").
БББББББББББББББ
БББББББББББББББ
* Replace battery and perform HW reset (refer to
Battery replacement" in Interface conditions").
БББББББББББББББ
БББББББББББББББ
* Check connector X10 (+24 V) on the l/O subas
БББББББББББББББ
sembly.
БББББББББББББББ
2665 VOLTAGE FAILURE 1ST I/O
БББББББББББББББ
+24 V voltage missing on I/O assembly.
БББББББББББББББ
БББББББББББББББ
2666 UART FRAMING ERROR
20 mA current loop interrupted.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2667 PLCRAM ERROR
BIT coupling board RAM is faulty.
БББББББББББББББ
БББББББББББББББ
2668 PLC PROGRAM < 2 ms
PLC program requires less than 2 ms for one
БББББББББББББББ
cycle. The PLC program must have a cycle
БББББББББББББББ
Iength of min. 2 ms to permit proper access to the information on the bit coupling board.
БББББББББББББББ
БББББББББББББББ
3 - 1
БББББББББББББББ
* Check connector X10 (+24 V) on the I/O assem
bly.
БББББББББББББББ
БББББББББББББББ
* Check connector on CNC, cable and connector
БББББББББББББББ
on input device.
БББББББББББББББ
* Data input device switched on?
БББББББББББББББ
* Baud rate, number of stop bits correct?
БББББББББББББББ
* Replace NCPLC coupling board.
БББББББББББББББ
БББББББББББББББ
* Increase PLC cycle time.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
NC errors
CC 220 / 320
Error messages
ERROR CAUSE
2669 PLC TIMING ERROR
Cycle time longer than 10 ms.
БББББББББББББББ
БББББББББББББББ
Faulty synchronization between PLC and NC
БББББББББББББББ
No data exchange between CNC and PLC.
БББББББББББББББ
2670 PLC TIMEOUT
БББББББББББББББ
PLC not running (red LED ZE stopped" lit) or running too fast.
БББББББББББББББ
БББББББББББББББ
Calling alarm or timecontrolled modules can
БББББББББББББББ
change the PLC cycle times. If the time de fined in MP 6002 is exceeded, the error mess
БББББББББББББББ
age is displayed. Ready2" is briefly cleared.
БББББББББББББББ
БББББББББББББББ
2671 UART PARITY ERROR
Parity error in data transfer X11/20 mA, CP,
БББББББББББББББ
panel, terminal.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2672 RAMPARITY ERROR
RAM faulty.
БББББББББББББББ
SW does not completely initialize RAM.
БББББББББББББББ
БББББББББББББББ
2673 OVERFLOW KEYDAT
Data loss due to excessively fast key oper
БББББББББББББББ
ation; too many characters read by panel
БББББББББББББББ
simultaneously.
БББББББББББББББ
ERROR REMEDY
* Check the PLC program (endless loop).
БББББББББББББББ
БББББББББББББББ
* Replace PIC board in the CNC.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check MPP P6002. * Check PLC program.
БББББББББББББББ
* Connection PLC <-> NC correct?
БББББББББББББББ
* Battery failure on ZE, NT, TZ?
БББББББББББББББ
* Switch EDIT/MONITOR on ZE subassembly to
MONITOR" position.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* UART module faulty; replace CP, replace panel
БББББББББББББББ
control (panel/terminal).
БББББББББББББББ
* Wrong data from paper tape reader; check
paper tape (parity).
БББББББББББББББ
* Input device faulty?
БББББББББББББББ
БББББББББББББББ
* Replace MEM board.
БББББББББББББББ
* Clear logic.
БББББББББББББББ
БББББББББББББББ
* 1. Control reset
БББББББББББББББ
2. Press keys more slowly.
БББББББББББББББ
* ASCII keyboard faulty (key jammed).
БББББББББББББББ
2674 OVERFLOW POTINDAT
БББББББББББББББ
Potentiometer buffer is full; loss of potentio meter data due to excessively slow proces
БББББББББББББББ
sing.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2675 OVERFLOW MTBINDAT
БББББББББББББББ
MTB buffer is full. Panel sends too many data to CNC.
БББББББББББББББ
БББББББББББББББ
Loss of MTB data due to excessively slow
БББББББББББББББ
processing.
БББББББББББББББ
Interface software wrong or faulty.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
3 - 2
БББББББББББББББ
* Panel control subassembly faulty? Replace sub
assembly.
БББББББББББББББ
* Processor P1 too slow? Reload SW or replace CP
БББББББББББББББ
subassembly.
БББББББББББББББ
* Clear logic.
БББББББББББББББ
БББББББББББББББ
* MTB subassembly (046136-) faulty (TC 235
only); replace subassembly.
БББББББББББББББ
БББББББББББББББ
* P1 processor working too slowly; reload SW or
БББББББББББББББ
replace CP subassembly.
БББББББББББББББ
* Interface processor or RAM faulty; replace CP
БББББББББББББББ
subassembly.
БББББББББББББББ
* Wrong interface software; replace EPROMs. * Clear logic.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
NC errors
CC 220 / 320
Error messages
ERROR CAUSE
2676 OVERFLOW CLOCKDAT
Clock, Ident or Version buffer overflow.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2678 CHANNEL NOT OPEN
Internal software error (interface cannot be
БББББББББББББББ
opened).
БББББББББББББББ
Log book output is aborted with mode
БББББББББББББББ
change.
БББББББББББББББ
2679 MEMORY DESTROYED
БББББББББББББББ
One or more monitored memory areas have
БББББББББББББББ
been destroyed.
БББББББББББББББ
2680 UART ERROR 20
UART is defective.
БББББББББББББББ
БББББББББББББББ
2681 VOLTAGE FAILURE 2ND I/O
БББББББББББББББ
24V for the 2nd I/O card is not present.
БББББББББББББББ
ERROR REMEDY
* Panel control subassembly faulty? Replace sub
БББББББББББББББ
assembly.
БББББББББББББББ
* Partyline SW faulty?
БББББББББББББББ
* Clear logic.
БББББББББББББББ
* Control reset; inform aftersales service if
БББББББББББББББ
necessary.
БББББББББББББББ
* Control reset.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Load backup.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
- replace card -
БББББББББББББББ
БББББББББББББББ
* Check card or power supply connections
БББББББББББББББ
3 - 3
Flexible Automation
NC errors
CC 220 / 320
Error messages
3 - 4
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
4. DNC ERRORS
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
79 UPGRADE LEVEL INACTIVE
БББББББББББББББ
If no messages are sent to the master control computer:
БББББББББББББББ
KS tables not present.
БББББББББББББББ
БББББББББББББББ
104 MEMORY FULL
The LSV2 function Readingin" is aborted
БББББББББББББББ
since insufficient memory space available.
БББББББББББББББ
105 ERROR IN FILE STRUCTURE
БББББББББББББББ
An error has been discovered in the structure of the output file.
БББББББББББББББ
БББББББББББББББ
The LSV2 function Output" is aborted since
БББББББББББББББ
an error has been found in the output file structure.
БББББББББББББББ
БББББББББББББББ
113 NO REF. POINTS
During activation of DA mode; reference
БББББББББББББББ
points not approached.
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
* Apply KS tables; install word coupler.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Provide more memory capacity and start read
БББББББББББББББ
ingin again.
БББББББББББББББ
БББББББББББББББ
* Check file syntax. * Check file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Travel to reference points.
БББББББББББББББ
БББББББББББББББ
305 MEMORY FULL
БББББББББББББББ
Memory space not sufficient for reading in files.
БББББББББББББББ
БББББББББББББББ
323 EDIT ENABLE MISSING
If no messages are sent to the master control
БББББББББББББББ
computer: The edit enable is missing from the
БББББББББББББББ
NC to permit a file to be deleted.
БББББББББББББББ
324 PROGRAM ACTIVE
БББББББББББББББ
If no message is sent to the master control computer:
БББББББББББББББ
A program is already active when a table is
БББББББББББББББ
selected.
БББББББББББББББ
396 INVALID FILE GROUP
БББББББББББББББ
If no messages are sent to the master control computer: The group is not defined within the
БББББББББББББББ
NC.
БББББББББББББББ
399 FILE PROTECTED
БББББББББББББББ
If no messages are sent to the master control
БББББББББББББББ
computer: Reading, writing, execution or deletion not permitted.
БББББББББББББББ
БББББББББББББББ
4 - 1
БББББББББББББББ
* Provide more memory capacity and start reading
in again.
БББББББББББББББ
БББББББББББББББ
* Set edit enable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Cancel program and repeat function.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change master control computer telegram.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change file protection.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
1131 FILE IN LIBRARY
The file to be read in already exists in the li
БББББББББББББББ
brary.
БББББББББББББББ
2010 FILE ALREADY EXISTS
БББББББББББББББ
The file to be read in already exists in the
БББББББББББББББ
control.
БББББББББББББББ
The LSV2 function Readingin" is aborted
БББББББББББББББ
since the file with the number of the DFS
БББББББББББББББ
identifier already exists.
БББББББББББББББ
2014 FILE TRANSFER ERROR
The internal conversion routine reports an
БББББББББББББББ
error (readingin).
БББББББББББББББ
2220 FILE NONEXISTENT
БББББББББББББББ
If no messages are sent to the master control computer: Selected file does not exist in the
БББББББББББББББ
NC.
БББББББББББББББ
БББББББББББББББ
Error during output. Requested file does not exist.
БББББББББББББББ
БББББББББББББББ
2366 V.24 ERROR USER A
General error on interface X32* ).
БББББББББББББББ
-
БББББББББББББББ
*) USER A = interface X32
БББББББББББББББ
БББББББББББББББ
2368 V.24 OVERFLOW USER A
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2370 V.24 PARITY USER A
БББББББББББББББ
БББББББББББББББ
USER B = interface X31
The UART on the V24 board reports overflow. More than the specified number of data bits were received.
The UART on the V24 board reports a parity error after reception of a character.
ERROR REMEDY
* Lock the file in the library or read in file with
БББББББББББББББ
another number.
БББББББББББББББ
БББББББББББББББ
* Clear the existing file.
БББББББББББББББ
* Read in file with another number.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart file transfer.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Transfer file to NC; change master control com
puter telegram.
БББББББББББББББ
* Was search performed for correct file?
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* HW reset.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Set data format.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Set data format.
БББББББББББББББ
БББББББББББББББ
2372 V.24 PROTOC. ERROR USER A
БББББББББББББББ
UART on the V24 board reports error after
БББББББББББББББ
reception of a character.
БББББББББББББББ
2374 V.24 INTERRUPTION USER A
The UART on the V24 board reports an error
БББББББББББББББ
after reception of a character.
БББББББББББББББ
2376 RESTART ERROR
БББББББББББББББ
V24 board reports error during startup (rein itialization of the DNC interface).
БББББББББББББББ
БББББББББББББББ
4 - 2
БББББББББББББББ
* Set data format.
БББББББББББББББ
БББББББББББББББ
* Set data format.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* HW reset.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
2377 EPROM ERROR
V24 board reports error during testing of
БББББББББББББББ
EPROM.
БББББББББББББББ
2378 V.24 RAM1 ERROR
БББББББББББББББ
V24 board reports error of the interface RAM
БББББББББББББББ
on the V24 board.
БББББББББББББББ
2379 V.24 RAM2 ERROR
V24 board reports error of the interface RAM
БББББББББББББББ
on the V24 board.
БББББББББББББББ
2380 V.24 COMMAND ERROR
БББББББББББББББ
V24 board reports corrupt command from the
БББББББББББББББ
NCSW.
БББББББББББББББ
2387 DNC TIMEOUT
No further telegram was received within the
БББББББББББББББ
monitoring period.
БББББББББББББББ
A send telegram could not be sent to the
БББББББББББББББ
master control computer during the monitor ing period.
БББББББББББББББ
БББББББББББББББ
2389 CNC IN LOCAL MODE
БББББББББББББББ
IF signal LOCAL/REMOTE not LOW.
БББББББББББББББ
ERROR REMEDY
* Replace EPROM on the V24 board.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Replace V24 board.
БББББББББББББББ
БББББББББББББББ
* Replace V24 board.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Switch DNC off and then back on again.
БББББББББББББББ
БББББББББББББББ
* File transfer was aborted: repeat file transfer.
БББББББББББББББ
* Telegram to the master control computer was
БББББББББББББББ
lost.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Switch NC to REMOTE.
БББББББББББББББ
2390 FCT NOT PERMITTED
БББББББББББББББ
If no messages are sent to the master control
БББББББББББББББ
computer: The group is not permitted in the NC for the selected function (e.g. activation of
БББББББББББББББ
a diagnosis program).
БББББББББББББББ
2391 NO MEMORY ACCESS
БББББББББББББББ
If no messages are sent to the LR: The mem ory is occupied at the NC by a different func
БББББББББББББББ
tion.
БББББББББББББББ
БББББББББББББББ
2392 FILE ACTIVE
БББББББББББББББ
If no messages are sent to the master control
БББББББББББББББ
computer: The file cannot be deleted be cause it is active.
БББББББББББББББ
БББББББББББББББ
2393 FCT CURRENTLY NOT POSSIBLE
PLC has not yet acknowledged last remote
БББББББББББББББ
job.
БББББББББББББББ
2395 NC RUNNING
БББББББББББББББ
A program is already being executed when DA mode is activated.
БББББББББББББББ
БББББББББББББББ
4 - 3
БББББББББББББББ
* Change master control computer telegram.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Abort function which is occupying the memory.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Cancel file, abort linking and editing.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Last job must first be acknowledged by the PLC;
БББББББББББББББ
abortion of the last remote job.
БББББББББББББББ
БББББББББББББББ
* Set FEED HOLD, cancel program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
2397 MONITOR/SIMULATION ACTIVE
DNC cannot be switched off with active moni
БББББББББББББББ
tor/ simulation.
БББББББББББББББ
БББББББББББББББ
2398 INVALID FILE NO
If no messages are sent to the master control
БББББББББББББББ
computer: The No. is not permitted for the
БББББББББББББББ
selected function within the group (e.g. read ing in the file).
БББББББББББББББ
БББББББББББББББ
2399 READINGIN ACTIVE
The CC200/300 refuses a request of the DNC
БББББББББББББББ
computer for the LSV2 function Automatic" at
БББББББББББББББ
the initiative of the CC200/300 since READ INGIN is active via a different interface.
БББББББББББББББ
БББББББББББББББ
3540 TOOL MAGAZINE
When selecting a program via LSV2, not all
БББББББББББББББ
programmed tools are in the magazine.
БББББББББББББББ
БББББББББББББББ
3541 MANUAL CHANGE NOT PERMITTED
Program selection via LSV2:
БББББББББББББББ
More tools are programmed than the maga
БББББББББББББББ
zine will hold.
БББББББББББББББ
ERROR REMEDY
* Abort diagnosis program, then switch off DNC.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change master control computer telegram.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Abort readingin and restart automatic execution.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Tool completely before selecting the program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Modify the program so that the tools are enough.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
4641 DNC HARDWARE ERROR
БББББББББББББББ
Interface board reports an HW error during the DNC operation (LSV2DNC).
БББББББББББББББ
The BAB subassembly reports an HW fault.
БББББББББББББББ
БББББББББББББББ
4642 BAB: ADDRESS ERROR
The specified destination address cannot be
БББББББББББББББ
accessed.
БББББББББББББББ
4644 BAB: NO CENTRAL CONTROL UNIT
БББББББББББББББ
The BAB user does not have any connection
БББББББББББББББ
to the BAB central control unit.
БББББББББББББББ
4650 BAB: CRC ERROR
This error message can occur only for the
БББББББББББББББ
BAB central control unit (control cannot be
БББББББББББББББ
central control unit). It was not possible to
БББББББББББББББ
transfer a telegram after 2 attempts.
БББББББББББББББ
4651 TSUBAB BLOCKED
БББББББББББББББ
The BAB subassembly does not enable the interface RAM.
БББББББББББББББ
БББББББББББББББ
4 - 4
БББББББББББББББ
* Check interface board. * HW reset; if this is not successful, replace the
БББББББББББББББ
subassembly.
БББББББББББББББ
БББББББББББББББ
* Connect the corresponding user with the bus.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check functioning of central control unit.
БББББББББББББББ
* Check bus for interruptions.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Switch the DNC on and off.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4653 BAB STATUS PORT
Status port copy was not updated. An inter
БББББББББББББББ
rupt was swallowed".
БББББББББББББББ
4654 UNDEF. A IDU (INTERNAL)
БББББББББББББББ
Unknown LSV2 function within the CNC
БББББББББББББББ
4658 BAB: USER NOT READY
БББББББББББББББ
User cannot accept a telegram since his RAM is still blocked by a preceding telegram, for
БББББББББББББББ
example.
БББББББББББББББ
БББББББББББББББ
4659 PLC JOB KS DATA
БББББББББББББББ
LSV2: Invalid address in the job list of the
БББББББББББББББ
PLC.
БББББББББББББББ
LSV2: Specified group in the job list of the PLC does not exist.
БББББББББББББББ
LSV2: Specified table in the job list of the PLC
БББББББББББББББ
does not exist.
БББББББББББББББ
4660 KS SEND TAB BLOCKED
БББББББББББББББ
LSV2: Access to KS table is blocked.
БББББББББББББББ
ERROR REMEDY
* No remedy necessary, DNC continues running.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Use defined functions.
БББББББББББББББ
БББББББББББББББ
* Create memory. (Error message can occur only
with BAP central control unit).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct job list.
БББББББББББББББ
* Correct job list.
БББББББББББББББ
* Correct job list.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Enable KS table.
БББББББББББББББ
4662 OVERFLOW TA TABLE
No free space in the reference table.
БББББББББББББББ
БББББББББББББББ
4663 TSU: IDU FAULTY
The transport layer (TSU) has received an
БББББББББББББББ
undefined job type.
БББББББББББББББ
4664 TSU: REC. TELEGRAM TOO LONG
БББББББББББББББ
A receive telegram exceeds the permitted
БББББББББББББББ
length.
БББББББББББББББ
The partner exceeds the permitted LSV2 tele
БББББББББББББББ
gram length during telegram transmission.
БББББББББББББББ
4665 TSU: REC. SEQUENCE NO.
БББББББББББББББ
The sequence number contained in the tele gram header is invalid.
БББББББББББББББ
БББББББББББББББ
4666 TSU: SEND SEQUENCE NO.
The send sequence number is not plausible.
БББББББББББББББ
Loss of a telegram.
БББББББББББББББ
* Switch DNC off and on.
БББББББББББББББ
БББББББББББББББ
* The TSU rejects the one job; communication
БББББББББББББББ
continues.
БББББББББББББББ
БББББББББББББББ
* No remedy necessary. The corresponding tele
БББББББББББББББ
gram is rejected by the TSU.
БББББББББББББББ
* Compare the LSV2 telegram length of the control
БББББББББББББББ
and partner and set to valid value.
БББББББББББББББ
БББББББББББББББ
* No remedy necessary. The corresponding tele
gram is rejected.
БББББББББББББББ
БББББББББББББББ
* No remedy necessary. Communication con
БББББББББББББББ
tinues.
БББББББББББББББ
4667 TSU: INVALID TSUOPC.
БББББББББББББББ
The TSU opcode contained in the telegram header is unknown.
БББББББББББББББ
БББББББББББББББ
4 - 5
БББББББББББББББ
* The telegram is rejected. Communication con
tinues.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4668 TSU: SENDING BLOCKED
Telegrams cannot be sent because the re
БББББББББББББББ
ceiver does not acknowledge.
БББББББББББББББ
4669 TSU: SEND RESET
БББББББББББББББ
Unknown reason in a reset telegram for the send channel.
БББББББББББББББ
БББББББББББББББ
4670 TSU: RECEIVE RESET
БББББББББББББББ
Unknown reason in a reset telegram for the
БББББББББББББББ
receive channel.
БББББББББББББББ
4671 TSU: RESTART
Undefined reason in a restart telegram.
БББББББББББББББ
БББББББББББББББ
4672 TSU: INVALID CHANNEL NUMBER
БББББББББББББББ
A send job of the application layer contains
БББББББББББББББ
an invalid channel number.
БББББББББББББББ
4682 INDIVIDUAL DISABLE ACTIVE
At least 1 axis is disabled. As a result of this
БББББББББББББББ
the job cannot be executed.
БББББББББББББББ
ERROR REMEDY
* The error is caused by the receiver.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Communication software is not compatible.
Computer and control cannot communicate with
БББББББББББББББ
each other.
БББББББББББББББ
БББББББББББББББ
* Computer and control cannot communicate with
БББББББББББББББ
each other.
БББББББББББББББ
* Computer and control cannot communicate with
БББББББББББББББ
each other.
БББББББББББББББ
БББББББББББББББ
* The error is caused by the application layer.
БББББББББББББББ
БББББББББББББББ
* Cancel axis disable.
БББББББББББББББ
БББББББББББББББ
4691 FUNCTION BLOCKED BY PLC
БББББББББББББББ
Job was refused by the PLC.
БББББББББББББББ
4693 ERROR PENDING IN CNC
NCSTART is not possible if an error (except
БББББББББББББББ
DNC error).
БББББББББББББББ
4695 FUNCTION ALREADY ACTIVE
БББББББББББББББ
Function is already active.
БББББББББББББББ
4698 WRONG PROGRAM
DA mode cannot be activated since the sent
БББББББББББББББ
program does not correspond to the re
БББББББББББББББ
quested one.
БББББББББББББББ
БББББББББББББББ
* Try again, change PLC prog.
БББББББББББББББ
* Remedy error, abort function.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Wait.
БББББББББББББББ
* Send requested program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
4 - 6
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4708 READINGIN: FILE STRUCTURE
LSV2 automatic: DNC computer sends file
БББББББББББББББ
readingin end without correct end in the file
БББББББББББББББ
data.
БББББББББББББББ
LSV2 readingin: The following errors are es
БББББББББББББББ
tablished while reading in the data: parity
БББББББББББББББ
error, Ecode error, syntax error in the file
БББББББББББББББ
structure, invalid compensation value, invalid zero offset group, file name error in DFS
БББББББББББББББ
identifier, file protection error in DFS identifier,
БББББББББББББББ
invalid SPG or CLM identifier, various errors
БББББББББББББББ
for W, S, K files.
БББББББББББББББ
4709 READINGIN: PROTOCOL ERROR
Incompatible function code used during read
БББББББББББББББ
ing in via LSV2 by master control computer.
БББББББББББББББ
БББББББББББББББ
LSV2: The DNC computer does not keep to
БББББББББББББББ
the prescribed protocol for the readingin function.
БББББББББББББББ
БББББББББББББББ
4710 OUTPUT: PROTOCOL ERROR
Internal error during output.
БББББББББББББББ
БББББББББББББББ
The master control computer sends a defec tive output request (protocol) to the control.
БББББББББББББББ
БББББББББББББББ
LSV2: The DNC computer does not keep to
БББББББББББББББ
the prescribed protocol for the output func tion.
БББББББББББББББ
БББББББББББББББ
LSV2: The DNC computer sends a faulty re
БББББББББББББББ
quest telegram (wrong file number, group or syntax) for the output function at the initiative
БББББББББББББББ
of the control.
БББББББББББББББ
БББББББББББББББ
4711 FILEI/O UTILITY ERROR
Internal LSV2 system error, for the functions
БББББББББББББББ
READINGIN, OUTPUT and CLEAR.
БББББББББББББББ
Internal LSV2 system error, for the function
БББББББББББББББ
DIR output.
БББББББББББББББ
БББББББББББББББ
4713 OUTPUT ABORT: COMPUTER
The DNC computer aborts the LSV2 output
БББББББББББББББ
function by DNC control reset.
БББББББББББББББ
4714 READINGIN ABORT: COMPUTER
БББББББББББББББ
The DNC computer aborts the LSV2 read ingin function by a DNC control reset.
БББББББББББББББ
БББББББББББББББ
4 - 7
ERROR REMEDY
* Check file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check protocol on computer side.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check protocol.
БББББББББББББББ
БББББББББББББББ
* Restart output.
БББББББББББББББ
БББББББББББББББ
* Check the request telegram from the master
control computer.
БББББББББББББББ
БББББББББББББББ
* Check protocol.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart the function File output".
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* DNC control reset for the LSV2 functions READ
БББББББББББББББ
INGIN, OUTPUT and CLEAR (otherwise switch
БББББББББББББББ
off DNC and then switch back on again).
* DNC control reset (otherwise switch off DNC and
БББББББББББББББ
then switch back on again).
БББББББББББББББ
БББББББББББББББ
* Restart output.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart readingin.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4715 READINGIN: WRONG FILE
The number or group of the file transferred by
БББББББББББББББ
the computer is not that which was re
БББББББББББББББ
quested.
БББББББББББББББ
A file cannot be read in since the number
БББББББББББББББ
contained in the FSI identifier already exists.
БББББББББББББББ
БББББББББББББББ
The DNC computer sends an invalid file number in the DFS identifier in the LSV2 func
БББББББББББББББ
tion Readingin an L FILE".
БББББББББББББББ
БББББББББББББББ
The FSI identifier group stored in the file does not agree with the file group (readingin).
БББББББББББББББ
БББББББББББББББ
The DNC computer sends an incorrect group
БББББББББББББББ
in the DFS identifier for the LSV2 function Readingin".
БББББББББББББББ
БББББББББББББББ
The DNC computer sends a corrupt request
БББББББББББББББ
telegram (wrong file number, group or syntax) for the LSV2 function Readingin" at the initi
БББББББББББББББ
ative of the CC200/300.
БББББББББББББББ
ERROR REMEDY
* Check protocol on computer side.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Clear the existing file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart readingin.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check the group under which the file is known in
the master control computer.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart readingin.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart readingin.
БББББББББББББББ
БББББББББББББББ
4716 DATA AFTER FILE END
БББББББББББББББ
Characters were still received during read
БББББББББББББББ
ingin after M30 or M2.
БББББББББББББББ
The DNC computer sends data after the file
БББББББББББББББ
end for the LSV2 functions Readingin" or
БББББББББББББББ
Automatic".
БББББББББББББББ
4717 NO ACCESS TO DNC RAM
The CC200/300 cannot enter an LSV2 tele
БББББББББББББББ
gram on the V24 board since the board does
БББББББББББББББ
not enable the internal RAM.
БББББББББББББББ
4718 TELEGRAM CODE UNKNOWN
An unknown code is discovered on the user
БББББББББББББББ
Ievel when decoding a telegram.
БББББББББББББББ
БББББББББББББББ
The DNC computer sends an unknown LSV2 telegram identification.
БББББББББББББББ
БББББББББББББББ
4719 LINK FAULTY
An LSV2 telegram cannot be sent by the
БББББББББББББББ
CC200/300 since the link to the computer is
БББББББББББББББ
broken.
БББББББББББББББ
4 - 8
БББББББББББББББ
* The file is created without the characters after
БББББББББББББББ
M30 or M2.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check V24 board.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* No remedy necessary; transfer continues.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check telegram identification.
БББББББББББББББ
БББББББББББББББ
* Check connecting cable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4720 COMPUTER NOT READY TO RECEIVE
An LSV2 telegram cannot be sent by the
БББББББББББББББ
CC200/300 because the computer does not
БББББББББББББББ
accept the telegram (neg. acknowledge
БББББББББББББББ
ment).
БББББББББББББББ
4721 DNC UNDEF ERROR CODE V24
The V24 board signals an internal error to the
БББББББББББББББ
CC200/300 (not further defined).
БББББББББББББББ
БББББББББББББББ
4722 TELEGRAM TOO LONG
DNC computer sends an excessively long
БББББББББББББББ
LSV2 telegram (telegram length > than de
БББББББББББББББ
fined in the corresponding machine para meter).
БББББББББББББББ
БББББББББББББББ
4723 CLEAR FILE ERROR
Various errors in the LSV2 function Clear
БББББББББББББББ
file".
БББББББББББББББ
- File group not defined
- Syntax error
БББББББББББББББ
- File or file group deleteprotected
БББББББББББББББ
- File does not exist
БББББББББББББББ
- File is active
- File is being used
БББББББББББББББ
- File is in library
БББББББББББББББ
БББББББББББББББ
4724 PLC NOT INITIALIZED
БББББББББББББББ
LSV2 initialization with the PC600 has not
БББББББББББББББ
functioned with PC600 coupling.
БББББББББББББББ
ERROR REMEDY
* Check DNC computer.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Switch DNC off and then back on again; check
БББББББББББББББ
V24 board.
БББББББББББББББ
БББББББББББББББ
* DNC computer must correct telegram length.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Remedy cause of fault; repeat function.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check PLC block.
БББББББББББББББ
БББББББББББББББ
4725 PLC DATA TRANSFER
БББББББББББББББ
The PLC acknowledges an LSV2 telegram from the DNC computer negatively.
БББББББББББББББ
БББББББББББББББ
4726 PLC SEND TELEGRAM
PLC wishes to send an excessively long tele
БББББББББББББББ
gram to the DNC computer (telegram length
БББББББББББББББ
> than defined in corresponding MP).
БББББББББББББББ
PLC uses an NC telegram identification.
БББББББББББББББ
БББББББББББББББ
4733 PLC BLOCKING RECEPTION
PLC no longer accepts any LSV2 telegrams
БББББББББББББББ
from the DNC computer.
БББББББББББББББ
4737 DNC CONTROL RESET BY COMPUTER
БББББББББББББББ
File transfer aborted by master control com puter.
БББББББББББББББ
БББББББББББББББ
4 - 9
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check PLC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check PLC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart file transfer.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4739 PROTOCOL ERROR
The DNC computer sends an unauthorized
БББББББББББББББ
telegram for the LSV2 function Automatic".
БББББББББББББББ
4740 ACKNOWLEDGE DNC MESSAGES
БББББББББББББББ
Buffer for new messages is full since the Iast message is still acknowledged.
БББББББББББББББ
БББББББББББББББ
4750 STATUS TRANSFER IMPOSSIBLE
No memory space can be reserved for buffer
БББББББББББББББ
ing the status messages when the DNC is
БББББББББББББББ
switched on.
БББББББББББББББ
4751 NO STATUS MESSAGE
There is no space for buffering the status
БББББББББББББББ
data when a status message is generated.
БББББББББББББББ
4752 NO OPERATION MESSAGE
БББББББББББББББ
When a state which must be signaled is
БББББББББББББББ
changed, no operation message can be gen erated since the previous message is still
БББББББББББББББ
pending for transfer.
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Do not acknowledge received messages.
БББББББББББББББ
БББББББББББББББ
* Increase USERHEAP (SKONF).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* No remedy necessary.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* No remedy necessary.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
4753 MZA RECORDING
БББББББББББББББ
The PLC does not react to the MZA request of the NC.
БББББББББББББББ
БББББББББББББББ
4754 DATA BLOCK W/O DATA
The DNC has sent an empty data block dur
БББББББББББББББ
ing the function Direct execution" or Read
БББББББББББББББ
ingin".
БББББББББББББББ
4760 BLOCK TRANSFER ACTIVE
The CC200/300 refuses a request of the DNC
БББББББББББББББ
computer for the LSV2 function Automatic" at
БББББББББББББББ
the initiative of the CC200/300 since block
БББББББББББББББ
transfer is already active.
БББББББББББББББ
4761 SYNTAX ERROR
The DNC computer sends a corrupt request
БББББББББББББББ
telegram (wrong syntax) for the LSV2 function
БББББББББББББББ
Automatic" at the initiative of the CC200/300.
БББББББББББББББ
4763 AUTO. ABORT: COMPUTER
The DNC computer aborts the LSV2 function
БББББББББББББББ
Automatic" by a DNC control reset.
БББББББББББББББ
БББББББББББББББ
* Change the PLC program.
БББББББББББББББ
БББББББББББББББ
* Check the output logic of the DNC computer.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Abort block transfer and restart automatic execu
БББББББББББББББ
tion.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart automatic execution.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Restart automatic execution.
БББББББББББББББ
БББББББББББББББ
4 - 10
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
DNC errors
CC 220 / 320
Error messages
ERROR CAUSE
4804 KS ACCESS BLOCKED
Readingin of KS tables is currently blocked.
БББББББББББББББ
Output of KS tables is currently blocked.
БББББББББББББББ
LSV2 function Readingin/output" is aborted
БББББББББББББББ
since access to the W file is blocked (PLC access).
БББББББББББББББ
LSV2 function Readingin" is aborted since
БББББББББББББББ
the DNC computer has sent corrupt KS data.
БББББББББББББББ
4810 KSDEF: TEXT LENGTH
The LSV2 function Readingin" is aborted
БББББББББББББББ
since the DNC computer has sent an error in
БББББББББББББББ
the definition part of the KS data.
БББББББББББББББ
4811 KSDEF: NUMBER OF GROUPS
БББББББББББББББ
The LSV2 function Readingin  is aborted since the DNC computer has sent an error in
БББББББББББББББ
the definition part of the KS data.
БББББББББББББББ
4812 KSDEF: ADDRESSES
БББББББББББББББ
The LSV2 function Readingin" is aborted
БББББББББББББББ
because the DNC computer has sent an error in the definition part of the KS data.
БББББББББББББББ
БББББББББББББББ
4813 KSDEF: STATUS TEXT
БББББББББББББББ
The LSV2 function Readingin" is aborted
БББББББББББББББ
because the DNC computer has sent an error
БББББББББББББББ
in the definition part of the KS data.
БББББББББББББББ
4814 KSDEF: GROUP TEXT
The LSV2 function Readingin" is aborted
БББББББББББББББ
because the DNC computer has sent an error
БББББББББББББББ
in the definition part of the KS data.
БББББББББББББББ
4815 KSDEF: SUBTABLE
The subtable to be read in is undefined.
БББББББББББББББ
The LSV2 function Readingin" is aborted
БББББББББББББББ
because the DNC computer has sent an error
БББББББББББББББ
in the definition part of the KS data.
БББББББББББББББ
4816 KSDEF: SYNTAX
The LSV2 function Readingin" is aborted
БББББББББББББББ
because the DNC computer has sent an error
БББББББББББББББ
in the definition part of the KS data.
БББББББББББББББ
ERROR REMEDY
* Start readingin again later.
БББББББББББББББ
* Start output again later.
БББББББББББББББ
* Restart readingin.
БББББББББББББББ
* Enable PLC access. * Tool file corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check subtable number.
БББББББББББББББ
* KS table definition part corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Tool file corrupt.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
4817 OUTPUT ACTIVE
Output" is active when DA mode is acti
БББББББББББББББ
vated.
БББББББББББББББ
4 - 11
* Abort output.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Note:
If a transfer error occurs, all data which are received up until the point when the error is detected are still pro cessed. The control then reinitializes the interface.
When an interface hardware error is detected, the current DNC function is aborted and the DNC interface is deactivated.
DNC errors
CC 220 / 320
Error messages
4 - 12
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
5. RUNTIME ERRORS
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
50 TABLE NOT PRESENT
БББББББББББББББ
It was attempted to activate a table which does not exist in the NC block with G22 K...
БББББББББББББББ
or V....
БББББББББББББББ
БББББББББББББББ
One of the Gcodes G154 - G159 or G254 ­G259 was programmed in the NC block. The
БББББББББББББББ
corresponding group is not activated in the
БББББББББББББББ
machine parameter P4501.
БББББББББББББББ
Compensation or zero shift table does not
БББББББББББББББ
exist.
БББББББББББББББ
БББББББББББББББ
The KS table specified in the CPL TD com mand does not exist.
БББББББББББББББ
БББББББББББББББ
67 INPUT ERROR
No dwell time (F) was programmed in the
БББББББББББББББ
block for the dwell time in spindle revolutions
БББББББББББББББ
(G104). The Fvalue is missing in the NC block with
БББББББББББББББ
G4 (dwell time).
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
* Change part program or create corresponding
table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program or change P4501
Number of zero shift groups".
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Create or reload table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program or create or reload de
sired table.
БББББББББББББББ
БББББББББББББББ
* Always specify a dwell time (F) in the block with
БББББББББББББББ
dwell time in spindle revolutions (G104).
БББББББББББББББ
* Add Fvalue in the NC block.
БББББББББББББББ
БББББББББББББББ
73 INPUT INCORRECT
БББББББББББББББ
A block was selected for a block search in
БББББББББББББББ
which thread cutting (G33) is modally active.
БББББББББББББББ
76 INVALID CHARACTER
Invalid character in the part program.
БББББББББББББББ
Block skip symbol /" is not programmed in
БББББББББББББББ
the first column.
БББББББББББББББ
A letter is programmed for which the type is set to 1 (error) in the MP 9000.
БББББББББББББББ
БББББББББББББББ
76 INVALID CHARACTER
БББББББББББББББ
The character \" (backslash) is detected at
БББББББББББББББ
the start of a block in the part program during active program testing, although no break
БББББББББББББББ
point was set for this block.
БББББББББББББББ
77 ADDRESS EXISTS SEVERAL TIMES
БББББББББББББББ
An NC address which must be programmed
БББББББББББББББ
only once in the NC block (settable via MP
9000) is programmed several times.
БББББББББББББББ
G875, G876, G877, G878 is in one block with
БББББББББББББББ
another G code.
БББББББББББББББ
Further G codes in addition to the couple command are programmed in one NC block.
БББББББББББББББ
БББББББББББББББ
5 - 1
БББББББББББББББ
* Only select blocks in which thread cutting is not
БББББББББББББББ
active for the block search.
БББББББББББББББ
* Read in program again.
БББББББББББББББ
* Change part program.
БББББББББББББББ
* Change part program or MP.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Remove the \" symbol.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change the part program or MP 9000.
БББББББББББББББ
БББББББББББББББ
* Change the NC program.
БББББББББББББББ
БББББББББББББББ
* Change the NC program
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
78 FORMAT ERROR
Readin format for F, M or S word is invalid.
БББББББББББББББ
БББББББББББББББ
78 INVALID FORMAT
БББББББББББББББ
Variable notation (VAR=33, G[VAR]) is not permitted for thread cutting (G33).
БББББББББББББББ
БББББББББББББББ
Variable notation (VAR=75, G[VAR]) is not
БББББББББББББББ
permitted for measuring probe input (G75).
БББББББББББББББ
An asynchronous axis is programmed whose
БББББББББББББББ
address letter is assigned an incorrect type
БББББББББББББББ
value in the machine parameter program (P9000).
БББББББББББББББ
БББББББББББББББ
An auxiliary function address has a word con
БББББББББББББББ
tent 2147483647 or -2147483648.
БББББББББББББББ
An auxiliary function address has the type 12
БББББББББББББББ
(MP 9000).
БББББББББББББББ
The NC word content of an auxiliary function
БББББББББББББББ
address is greater than allowed by the
БББББББББББББББ
number of integer positions (machine para
БББББББББББББББ
meter P2007).
БББББББББББББББ
An NC address of the type 12 (machine
БББББББББББББББ
parameter P9000) String" has a CPL ex
БББББББББББББББ
pression as a variable address which does return a string.
БББББББББББББББ
БББББББББББББББ
The permitted number of digits of an NC
БББББББББББББББ
word (machine parameter P9000) has been exceeded.
БББББББББББББББ
БББББББББББББББ
A blank NC word has been programmed, i.e.
БББББББББББББББ
no digits. e.g.: N10XY100.
БББББББББББББББ
An NC address of the type 2, 5, 8, 11 Integer or
БББББББББББББББ
12 Str (machine parameter P9000) has been
БББББББББББББББ
programmed with a .", i.e. as a real value.
БББББББББББББББ
A Gword with variable address is interpreted as
БББББББББББББББ
G23, G24, G70, G71 or G92, e.g.: G[92].
БББББББББББББББ
A G98 is programmed in the NC block and
БББББББББББББББ
the modally present preparatory function is
БББББББББББББББ
not G0 or G1.
БББББББББББББББ
The K or V addresses possess the type 3, 6
БББББББББББББББ
or 10 (MPP P9000) in the NC block with G22
БББББББББББББББ
and the word content is 2147483647 or
БББББББББББББББ
-2147483648. (Possible only with variable address and CPL expression).
БББББББББББББББ
БББББББББББББББ
5 - 2
ERROR REMEDY
* Program in valid format.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Program G33 without CPLvariable.
БББББББББББББББ
БББББББББББББББ
* Program G75 without CPLvariable.
БББББББББББББББ
БББББББББББББББ
* Change MPP.
БББББББББББББББ
БББББББББББББББ
* Address type may have the following values: 2,
3, 5, 6, 7, 8, 10, 11
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Change MP.
БББББББББББББББ
БББББББББББББББ
* Change part program or MPP.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
The K or V address is type 4 (MP P9000) in the NC block with G22.
БББББББББББББББ
БББББББББББББББ
Incorrect transfer parameter of the type
БББББББББББББББ
Real" - for subroutine call.
БББББББББББББББ
Incorrect transfer parameter - of the type In
БББББББББББББББ
teger" - for subroutine call.
БББББББББББББББ
Spindle speed not declared as real or integer.
БББББББББББББББ
БББББББББББББББ
Retraction angle lies between 60 and 90 de
БББББББББББББББ
grees.
БББББББББББББББ
Retraction angle < 0 degrees.
БББББББББББББББ
An auxiliary function subroutine call is pro grammed with variable address, for example
БББББББББББББББ
A[10] subroutine call defined with A10 in the
БББББББББББББББ
machine parameter P4007.
БББББББББББББББ
An M subroutine call is programmed with
БББББББББББББББ
variable address (machine parameter P4006).
БББББББББББББББ
A G subroutine call is programmed with vari
БББББББББББББББ
able address (machine parameter P4002).
БББББББББББББББ
Wrong format for compensation value table.
БББББББББББББББ
БББББББББББББББ
Programmed Hirth axis value is invalid.
ERROR REMEDY
* Change MP.
БББББББББББББББ
БББББББББББББББ
* Check and correct transfer parameters of the
БББББББББББББББ
corresponding subroutine call.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change MP 9019.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change retraction angle.
БББББББББББББББ
* Change retraction angle.
БББББББББББББББ
* Change auxiliary function code.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change M code.
БББББББББББББББ
БББББББББББББББ
* Change G code.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check and change compensation values.
A value is programmed via a switching func
БББББББББББББББ
tion which does not correspond to the format
БББББББББББББББ
defined in the MPP.
БББББББББББББББ
The format of the address M is set to 1, 4, 9
БББББББББББББББ
or 12 in the MPP P9000.
БББББББББББББББ
Rotary axis for tangential tool guidance is
БББББББББББББББ
programmed with active circular interpolation.
БББББББББББББББ
БББББББББББББББ
A P or Q subroutine call is programmed with variable address or more than one subroutine
БББББББББББББББ
call is present in the NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
78 FORMAT INVALID
БББББББББББББББ
Variable notation was used when program ming G876, G877.
БББББББББББББББ
БББББББББББББББ
Programming of CPL variables (VAR=52, G/
БББББББББББББББ
VAR/) is not allowed when programming G51, G52.
БББББББББББББББ
БББББББББББББББ
5 - 3
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Enter prog. value again in correct format.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change MP.
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
* Program G51, G52 without CPL variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
79 UPGRADE LEVEL INACTIVE
Max. 3 synchronous axes may be pro
БББББББББББББББ
grammed in interpolation mode (G1, G73, ..)
БББББББББББББББ
in the COCOM version.
БББББББББББББББ
Call of a nonactivated upgrade level.
БББББББББББББББ
БББББББББББББББ
Invalid Gcode programmed.
БББББББББББББББ
The CPL code word is reserved.
БББББББББББББББ
БББББББББББББББ
The INP#(0,...) or PRN#(0,...) command was
БББББББББББББББ
used although the upgrade level CPL WITH PROGR. GRAPHICS is not active. The INKEY
БББББББББББББББ
command was used although the upgrade
БББББББББББББББ
level CPL WITH PROGR. GRAPHICS is not
БББББББББББББББ
active. CPL graphics commands were used although the upgrade level CPL WITH
БББББББББББББББ
PROGR. GRAPHICS is not active.
БББББББББББББББ
БББББББББББББББ
The reserved call TXT was programmed.
БББББББББББББББ
A reserved function call was used.
БББББББББББББББ
БББББББББББББББ
Error during readingin: S files are not permitted since no SPIL or PIC
БББББББББББББББ
200 is present.
БББББББББББББББ
БББББББББББББББ
Inadmissible jump out of application; soft ware error.
БББББББББББББББ
БББББББББББББББ
SPG identifier programmed.
БББББББББББББББ
AXIS COUPLING upgrade level was pro
БББББББББББББББ
grammed. Application bit not set.
БББББББББББББББ
БББББББББББББББ
G875 in CNC with servo 8card prog.
БББББББББББББББ
No limit switch range programmable with
БББББББББББББББ
G876, G877 was defined or no servoi avail
БББББББББББББББ
able.
БББББББББББББББ
Switch over spindle with G201/G202 with 2nd
БББББББББББББББ
spindle not applied.
БББББББББББББББ
80 SIGN ERROR
БББББББББББББББ
Positive for an NC address with type 5 or 6 (machine parameter P9000). Negative value
БББББББББББББББ
is programmed for integer or positive real.
БББББББББББББББ
БББББББББББББББ
Negative feed programmed.
БББББББББББББББ
81 MAX. SUBROUTINE DEPTH
Nesting of the subroutines is too deep.
БББББББББББББББ
БББББББББББББББ
5 - 4
ERROR REMEDY
* Program max. 3 synchronous axes in interpola
БББББББББББББББ
tion mode (G1, G73...).
БББББББББББББББ
БББББББББББББББ
* Inform aftersales service; retrofit upgrade con
БББББББББББББББ
figuration level.
БББББББББББББББ
* Change part program.
БББББББББББББББ
* Other variable name.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
* Inform aftersales service,
retrofit upgrade configuration level.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change variable name.
БББББББББББББББ
* Change variable name.
БББББББББББББББ
БББББББББББББББ
* Apply SPIL or PIC 200.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
* SPG identifier is not permitted.
БББББББББББББББ
* Adapt application.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* G875 only possible with servoi.
БББББББББББББББ
* Define range in MP6200 or use servoi.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Apply upgrade level 2nd spindle".
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Enter positive feed.
БББББББББББББББ
* Change subroutine call structure.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
writing in the PRN#(...) command.
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
104 MEMORY FULL
Warning for copying:
БББББББББББББББ
File is to be copied, but no memory space is
БББББББББББББББ
available.
БББББББББББББББ
The simulation memory via which the data
БББББББББББББББ
relevant to simulation are forwarded to the
БББББББББББББББ
output task is created upon entry into NC
БББББББББББББББ
block simulation if this memory does not yet exist. Memory space insufficient.
БББББББББББББББ
БББББББББББББББ
There is no longer sufficient memory space
БББББББББББББББ
for the OPENW command in order to create the desired file.
БББББББББББББББ
БББББББББББББББ
There is no longer sufficient memory space
БББББББББББББББ
for automatic expansion of a file opened for writing in the PRN#(...) command.
БББББББББББББББ
Error during readingin:
БББББББББББББББ
There is not sufficient memory space avail able for reading in a file.
БББББББББББББББ
БББББББББББББББ
The memory space is not sufficient for cre
БББББББББББББББ
ation of a KS table.
БББББББББББББББ
There is no space available to copy the NC
БББББББББББББББ
program for program optimization".
БББББББББББББББ
There is no space to create a DA buffer.
БББББББББББББББ
БББББББББББББББ
Not enough memory to record image.
БББББББББББББББ
Not enough memory for diagnostic file when
БББББББББББББББ
starting D28.
БББББББББББББББ
ERROR REMEDY
* Create memory space by deleting files and/or
БББББББББББББББ
control reset; perform function again.
БББББББББББББББ
БББББББББББББББ
* Reduce the simulation memory or delete other
БББББББББББББББ
files.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
БББББББББББББББ
* Possibly increase MP 6005.
БББББББББББББББ
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
* Create memory space by deleting files and/or
БББББББББББББББ
control reset.
БББББББББББББББ
5 - 5
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
CR
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
*I
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
105 ERROR IN FILE STRUCTURE
Error during readingin: The number of the
БББББББББББББББ
DFS identifier is larger than 14 digits.
БББББББББББББББ
БББББББББББББББ
Error in the structure of a D file.
БББББББББББББББ
Error in the end identifier (M02, M30, ETX).
БББББББББББББББ
БББББББББББББББ
Two successive DFS identifiers are separated without an end identifier.
БББББББББББББББ
БББББББББББББББ
SPG identifier programmed.
БББББББББББББББ
Compensation values occur during reading in
БББББББББББББББ
of a geometric compensation table which lie
БББББББББББББББ
outside the permitted value range.
БББББББББББББББ
An invalid checksum occurs for a PIC 200
БББББББББББББББ
program.
БББББББББББББББ
БББББББББББББББ
Error during readingin of D files in Intel hex format:
БББББББББББББББ
and LF missing at the start of a line.
ERROR REMEDY
* Correct number.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check Dfile.
БББББББББББББББ
* Program M02 <LF> or M30 <LF> or <ETX> at
БББББББББББББББ
the end of a file.
БББББББББББББББ
* Program M02 <LF> or M30 <LF> or <ETX>
after the first file.
БББББББББББББББ
БББББББББББББББ
* SPG identifier is not permitted.
БББББББББББББББ
* Change invalid compensation values of the
БББББББББББББББ
readin data.
БББББББББББББББ
БББББББББББББББ
* Check and correct checksum.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
*
nsert CR and LF.
БББББББББББББББ
Trying to convert invalid characters from ASCII to HEX.
БББББББББББББББ
БББББББББББББББ
More than 16 data bytes occur in one line.
БББББББББББББББ
The first position of the status byte is not 0.
БББББББББББББББ
БББББББББББББББ
Checksum in a line is not correct.
БББББББББББББББ
First four bits of base segment record contain
БББББББББББББББ
values not equal to 0.
БББББББББББББББ
БББББББББББББББ
The value for the status byte is not equal to 0, 1, 2.
БББББББББББББББ
БББББББББББББББ
The object code format code is corrupt for
БББББББББББББББ
PIC200.
БББББББББББББББ
Image file contains false characters, lines that
БББББББББББББББ
are too long, or has a corrupt structure.
БББББББББББББББ
125 BLOCK NONEXISTENT
БББББББББББББББ
Entered block number does not exist in this file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Convert only values from 0..9 and A..F.
БББББББББББББББ
БББББББББББББББ
* Maximum of 16 data bytes permitted in one line.
БББББББББББББББ
* First position of the status byte must be 0.
БББББББББББББББ
БББББББББББББББ
* Correct checksum.
БББББББББББББББ
* First four bits of the base segment record must
БББББББББББББББ
be 0.
БББББББББББББББ
БББББББББББББББ
* The status byte may contain only 0, 1, 2.
БББББББББББББББ
БББББББББББББББ
* Check object code format.
БББББББББББББББ
БББББББББББББББ
* Regenerate image file or reread via data I/O.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Enter existing block number.
БББББББББББББББ
БББББББББББББББ
5 - 6
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
An axis address is programmed in the NC
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
* Change part program
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
149 I/O DEVICE: TIMEOUT
Error during readingin/output: Data not arriv
БББББББББББББББ
ing. Connection faulty.
БББББББББББББББ
БББББББББББББББ
Readingin via DCR: All data has already been transferred. The error message is is
БББББББББББББББ
sued at the tape end.
БББББББББББББББ
150 PARITY
БББББББББББББББ
Error during readingin Parity error occurs if
БББББББББББББББ
- EIA occurs with even parity sum.
БББББББББББББББ
- ISO occurs with odd parity sum.
БББББББББББББББ
165 ADDRESS INVALID
An axis movement was programmed in the
БББББББББББББББ
same block as the dwell time in spindle revol
БББББББББББББББ
utions (G104).
БББББББББББББББ
- NO AXIS or
- AN ASYNCHRONOUS AXIS or
БББББББББББББББ
- A ROTARY AXIS or
БББББББББББББББ
- AN AXIS VALUE <> 1, -1
БББББББББББББББ
was programmed for switchover of drilling cycle and length compensation (G78).
БББББББББББББББ
БББББББББББББББ
A letter is programmed for which the type is
БББББББББББББББ
set to 9 (MPP P9000).
БББББББББББББББ
block with G4 dwell time.
БББББББББББББББ
An address is programmed which is not N, P,
БББББББББББББББ
K or V in the NC block with G22.
БББББББББББББББ
БББББББББББББББ
An axis address is programmed in the NC block with G22.
БББББББББББББББ
БББББББББББББББ
Axis address not in selected level.
БББББББББББББББ
S address programmed in G33 block.
БББББББББББББББ
БББББББББББББББ
Address of coupled slave axis was pro
БББББББББББББББ
grammed while coupled.
БББББББББББББББ
172 LIMIT SWITCH
Traverse path programmed which is outside
БББББББББББББББ
the programmed limit switch.
БББББББББББББББ
Programmed value for the rotary axis for tan
БББББББББББББББ
gential tool guidance is outside the limit
БББББББББББББББ
switch range.
БББББББББББББББ
ERROR REMEDY
* Check device connection, device setting and
БББББББББББББББ
interfaces.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Data device supplies incorrect times; check data
link.
БББББББББББББББ
* Set parity correctly.
БББББББББББББББ
БББББББББББББББ
* Do not program travel in the block with dwell
БББББББББББББББ
time in spindle revolutions (G104).
БББББББББББББББ
БББББББББББББББ
* Switchover of drilling cycle and length com
pensation must occur only to a synchronous lin
БББББББББББББББ
ear axis in positive or negative direction.
БББББББББББББББ
(Example: G78 Y-1).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program or MPP.
БББББББББББББББ
БББББББББББББББ
*
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Switch level.
БББББББББББББББ
* Remove Saddress from G33 block.
БББББББББББББББ
БББББББББББББББ
* Change NC program
БББББББББББББББ
БББББББББББББББ
* Program traverse path within the limit switch
БББББББББББББББ
range.
БББББББББББББББ
* Program axis value within the limit switch range.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 7
.
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
206 FILE NOT DELETABLE
Error during readingin:
БББББББББББББББ
CLM identifier if file group is not P, V, K or G.
БББББББББББББББ
214 SETTING CLOCK
БББББББББББББББ
Date or time cannot be read with the CPL Date/Time command.
БББББББББББББББ
БББББББББББББББ
326 INADMISSIBLE FILE NUMBER
Error during readingin:
БББББББББББББББ
File number not permitted.
БББББББББББББББ
1. Number < 1 or > 999999999.
2. Readingin blocked for this file (e.g. L1).
БББББББББББББББ
БББББББББББББББ
344 INPUT INCORRECT, AXIS RUNNING
Trying to switch over to the Caxis, but one
БББББББББББББББ
axis still possesses a travel command.
БББББББББББББББ
351 ALL LINK TAB. ACTIVE
БББББББББББББББ
It is not possible to create a new link table because all ten nonpermanent link tables are
БББББББББББББББ
active.
БББББББББББББББ
ERROR REMEDY
* Only delete files from the permitted file groups P,
БББББББББББББББ
V, K or G.
БББББББББББББББ
БББББББББББББББ
* Problems with partyline? * The time is currently being entered.
БББББББББББББББ
БББББББББББББББ
* Correct file number.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Initiate switchover from the PLC only when no
БББББББББББББББ
travel command is pending.
БББББББББББББББ
БББББББББББББББ
* Create additional permanent link tables and re
start linking.
БББББББББББББББ
БББББББББББББББ
354 LINKING ALREADY ACTIVE
БББББББББББББББ
A program has been selected for which no link table has yet been created; a link process
БББББББББББББББ
for another program is already active.
БББББББББББББББ
355 LINK ERROR
БББББББББББББББ
A program has been selected for which a link
БББББББББББББББ
process has already been performed; an error has been established.
БББББББББББББББ
БББББББББББББББ
356 NO RUNTIME MEMORY
БББББББББББББББ
There is no longer sufficient memory in order
БББББББББББББББ
to allow the program to run.
БББББББББББББББ
379 FILE DESTROYED
The block end identifier Line feed" and the
БББББББББББББББ
file end identifier ETX are missing in the last
БББББББББББББББ
block of a file when a string is read with the I
БББББББББББББББ
NP#(...) command.
БББББББББББББББ
БББББББББББББББ
* Abort linking and restart program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Establish the type of the error in NC mode under
БББББББББББББББ
SK Table selection"; remedy error and reselect program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Create memory space by deleting files and/or
БББББББББББББББ
control reset; call program again.
БББББББББББББББ
* Check opened file.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 8
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
386 LIMIT SWITCH 1st AXIS 387 LIMIT SWITCH 2nd AXIS
БББББББББББББББ
388 LIMIT SWITCH 3rd AXIS
БББББББББББББББ
389 LIMIT SWITCH 4th AXIS
БББББББББББББББ
390 LIMIT SWITCH 5th AXIS 391 LIMIT SWITCH 6th AXIS
БББББББББББББББ
392 LIMIT SWITCH 7th AXIS
БББББББББББББББ
393 LIMIT SWITCH 8th AXIS
БББББББББББББББ
Limit point outside the limit switch ranges.
БББББББББББББББ
394 INVALID COMPENSATION VALUE
Error during readingin of zero shift files:
БББББББББББББББ
Invalid zero shift value.
БББББББББББББББ
395 INVALID ZERO SHIFT GROUP
БББББББББББББББ
Error during readingin of zero shift files: Invalid zero shift group value.
БББББББББББББББ
БББББББББББББББ
396 INVALID FILE GROUP
Error during readingin:
БББББББББББББББ
Invalid file group in the DFS identifier.
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program or limit switch.
БББББББББББББББ
БББББББББББББББ
* Change zero shift value.
БББББББББББББББ
БББББББББББББББ
* Change zero shift group.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct file group.
БББББББББББББББ
397 FILE NAME FAULTY
БББББББББББББББ
Error during readingin: File name in the DFS identifier is longer than
БББББББББББББББ
30 characters.
БББББББББББББББ
398 PROTECTION FAULTY
БББББББББББББББ
Error during readingin: File protection in the DFS identifier contains
БББББББББББББББ
more than 4 characters or is not R, W,
БББББББББББББББ
E and D.
БББББББББББББББ
399 FILE PROTECTED
БББББББББББББББ
Trying to activate a table which is protected (type of protection E) in the NC block with
БББББББББББББББ
G22 K... or V.....
БББББББББББББББ
БББББББББББББББ
Trying with OPENR to open a readprotected file.
БББББББББББББББ
Trying with OPENW to open a writeprotected
БББББББББББББББ
file.
БББББББББББББББ
A TTY interface to be written by the PRN#(...)
БББББББББББББББ
command is already open.
БББББББББББББББ
The main program or a subroutine is pro
БББББББББББББББ
tected against execution.
5 - 9
БББББББББББББББ
* Shorten file name.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct file protection; may contain a maximum
БББББББББББББББ
of 4 characters: R, W, E and D.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program or protection E.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program or file protection.
БББББББББББББББ
* Change CPL program or file protection.
БББББББББББББББ
БББББББББББББББ
* Terminate parallel access, e.g. by control reset.
БББББББББББББББ
БББББББББББББББ
* Change protection or check call structure.
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
696 MEMORY FULL
Graphic memory is full.
БББББББББББББББ
БББББББББББББББ
Part program memory is full.
БББББББББББББББ
БББББББББББББББ
786 DEAD ZONE BLOCKED
Incorrect position in the claw dead zone with
БББББББББББББББ
out claw testing" having taken place.
БББББББББББББББ
787 INVALID CVALUE
БББББББББББББББ
Caxis is programmed with active circular in terpolation.
БББББББББББББББ
БББББББББББББББ
788 INADMISSIBLE AVALUE
БББББББББББББББ
Programmed acceleration outside the limit
БББББББББББББББ
values defined in the MPP.
БББББББББББББББ
789 G6 W/O AXIS INFO
Acceleration programming without input of
БББББББББББББББ
acceleration values.
БББББББББББББББ
ERROR REMEDY
* Store graphics and call again with Old part"
БББББББББББББББ
(Trumpf).
БББББББББББББББ
* Delete part programs which are not currently
БББББББББББББББ
required - control reset.
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change programming or limit values.
БББББББББББББББ
БББББББББББББББ
* Specify acceleration values for at least 1 axis.
БББББББББББББББ
БББББББББББББББ
789 TAP TOO SMALL
БББББББББББББББ
Tap too small for desired thread.
БББББББББББББББ
790 NO EWORD PROGRAMMED
M22 programmed without Eword.
БББББББББББББББ
БББББББББББББББ
791 INCORRECT CIRCULAR PATH PROGRAM
MING
БББББББББББББББ
M22/25 end point not on circular arc.
БББББББББББББББ
Circle without I, J.
БББББББББББББББ
792 INVALID EWORD
Traverse path per stroke greater than per
БББББББББББББББ
mitted traverse path, e.g. X10 E15 M22
БББББББББББББББ
793 INVALID HWORD
БББББББББББББББ
H > 999 or < 1
БББББББББББББББ
794 H WITHOUT TRAVERSING INFO
Hword programmed without traverse path.
БББББББББББББББ
БББББББББББББББ
795 LIMIT POSITION WRONGLY CALCULATED
БББББББББББББББ
Limit position is not correct.
БББББББББББББББ
БББББББББББББББ
* Select suitable tap.
БББББББББББББББ
* Program Eword.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change program.
БББББББББББББББ
БББББББББББББББ
* Program E > 0.01 or < 999.99.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Program H < 999 or > 1.
БББББББББББББББ
* Enter traverse path; e.g. X500 H10 M22.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Inform aftersales service.
БББББББББББББББ
796 INVALID LIMIT POSITION
БББББББББББББББ
Limit position below claws.
БББББББББББББББ
БББББББББББББББ
5 - 10
БББББББББББББББ
* Programming error in part program in the case
of externally created programs.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
797 MAXIM. 4 CLAWS
More than 4 claws were defined during claw
БББББББББББББББ
test.
БББББББББББББББ
800 ERROR IN PLC PROGRAM
БББББББББББББББ
A syntax error has been found in the PLC pro
БББББББББББББББ
gram.
БББББББББББББББ
Error during readingin: In Sfile (only PIC200
БББББББББББББББ
program).
БББББББББББББББ
An error has occurred in INTELHEX format.
БББББББББББББББ
БББББББББББББББ
1080 LINK TABLE NOT PRESENT
A CPL program was started in machine, data
БББББББББББББББ
I/O, diagnosis or compensation mode for
БББББББББББББББ
which no link table exists.
БББББББББББББББ
1131 FILE IN LIBRARY
Trying to open a file with OPENR or OPENW
БББББББББББББББ
which already exists in the library.
БББББББББББББББ
БББББББББББББББ
It is attempted to read in a file which exists in the library and is not locked.
БББББББББББББББ
БББББББББББББББ
The file specified in FIXB already exists in the
БББББББББББББББ
P group of the library as a cleared program.
БББББББББББББББ
ERROR REMEDY
* Correct program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct the PLC program.
БББББББББББББББ
БББББББББББББББ
* Check and correct format.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Create link table for the corresponding CPL pro
БББББББББББББББ
gram.
БББББББББББББББ
БББББББББББББББ
* Change CPL program or block file in the library.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* See above.
БББББББББББББББ
БББББББББББББББ
* Change file no. in FIXB or lock program in li
БББББББББББББББ
brary.
БББББББББББББББ
1137 LOAD KS TABLE
Readingin or output is active.
БББББББББББББББ
БББББББББББББББ
Error during readingin of KS tables.
БББББББББББББББ
БББББББББББББББ
Readingin cannot be started during copying
БББББББББББББББ
of KS tables.
БББББББББББББББ
1217 SWITCHOVER NOT PERMITTED
БББББББББББББББ
Test operation without total block or auxiliary block.
БББББББББББББББ
Rapid retraction of the Caxis prog. and trying
БББББББББББББББ
to switch back to the spindle without cancel
БББББББББББББББ
ling rapid retraction of the Caxis. G95, 33, 330, 104 is active and trying to
БББББББББББББББ
switch to the Caxis.
БББББББББББББББ
Trying to switch over to the Caxis in the block
БББББББББББББББ
search without traveling to the reference point.
БББББББББББББББ
Switchover to Caxis without reference point
БББББББББББББББ
and Caxis requires reference point.
БББББББББББББББ
Trying to switch over to the Caxis via a switching function with act. program.
БББББББББББББББ
БББББББББББББББ
5 - 11
* After readingin or output, copy KS tables with
БББББББББББББББ
diagnosis program D10.
БББББББББББББББ
* Read in again via diagnosis program. If the error
БББББББББББББББ
occurs again, the cause of the error is described more precisely by a new error message.
БББББББББББББББ
* Control reset; restart KS table copying operation.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Activate total block and auxiliary block.
БББББББББББББББ
* Switch off rapid retraction of the Caxis with G99
БББББББББББББББ
and program new retraction positions without C
БББББББББББББББ
axis.
* Switch off invalid Gfunctions before switchover
БББББББББББББББ
to Caxis.
БББББББББББББББ
* In a block search, program all switchover oper
БББББББББББББББ
ations with travel to reference point (MP 7605).
БББББББББББББББ
* Set all switchover operations with MP 7605 or
БББББББББББББББ
MP 1510 for Caxis to YES.
БББББББББББББББ
* Switchover via switching function is not possible
with active program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1218 INVALID PROGRAMMING
A travel movement of a synchronous axis is
БББББББББББББББ
contained in the switchover block Caxis
БББББББББББББББ
spindle/spindleCaxis.
БББББББББББББББ
The Caxis is programmed in turning oper
БББББББББББББББ
ation.
БББББББББББББББ
БББББББББББББББ
A spindle Mfunction or an Sword is con tained in the switchover block.
БББББББББББББББ
БББББББББББББББ
1228 OSCILLATING AXIS ACTIVE
G993 is active and the oscillating axis is pro
БББББББББББББББ
grammed by means of its address letter.
БББББББББББББББ
1236 G92 IS ACTIVE
БББББББББББББББ
G52 (set workpiece zero) must not be used with active G92 (set actual value).
БББББББББББББББ
БББББББББББББББ
1242 KS ACCESS BLOCKED
БББББББББББББББ
PLC access takes longer than 10 ms.
БББББББББББББББ
ERROR REMEDY
* Write switchover Mcode alone in a block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Delete Caxis programming in turning mode.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Write switchover Mcode alone in a block.
БББББББББББББББ
БББББББББББББББ
* Change part program or activate G994.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Cancel G92.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PLC program (enable access for NC).
БББББББББББББББ
1258 DRIVE ON ERROR
БББББББББББББББ
Drive on was cancelled without permission
БББББББББББББББ
of NC.
БББББББББББББББ
1259 STARTING NOT POSSIBLE
Safety cutout during input of subsequent
БББББББББББББББ
switching functions.
БББББББББББББББ
Clear residual travel with active safety cutout.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
1365 INSUFFICIENT CHECK POINTS
БББББББББББББББ
Trying to execute a SPLINE block without a
БББББББББББББББ
sufficient number of check points having been programmed.
БББББББББББББББ
БББББББББББББББ
Switchover from SPLINE interpolation to a
БББББББББББББББ
different interpolation mode has taken place. Only two check points were available for
БББББББББББББББ
block preparation for spline interpolation up
БББББББББББББББ
to then; it was not possible to execute the
БББББББББББББББ
SPLINE block.
БББББББББББББББ
1366 INVALID G CODE
A Gfunction was programmed which must
БББББББББББББББ
be used only with active spline interpolation.
БББББББББББББББ
БББББББББББББББ
An invalid Gfunction was programmed with active spline interpolation.
БББББББББББББББ
БББББББББББББББ
5 - 12
БББББББББББББББ
* Change PLC timing (refer to Interface condi
БББББББББББББББ
tions").
БББББББББББББББ
* Control reset, program cancellation or renewed
БББББББББББББББ
program selection.
БББББББББББББББ
* Control reset, program cancellation or renewed
БББББББББББББББ
program selection.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* At least three check points must be available for
БББББББББББББББ
block preparation in order to permit execution of a spline arc.
БББББББББББББББ
БББББББББББББББ
* At least three check points must be available for
БББББББББББББББ
block preparation in order to permit execution of a spline arc.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Activate spline interpolation or remove G func
БББББББББББББББ
tion previously.
БББББББББББББББ
БББББББББББББББ
* Remove corresponding Gfunction from the pro
gram.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1367 INVALID CHECK POINT
Two successive check points are identical
БББББББББББББББ
with active spline interpolation.
БББББББББББББББ
БББББББББББББББ
Three successive check points are in inad missible configuration on a straight line.
БББББББББББББББ
БББББББББББББББ
1368 INVALID WORKING AREA
БББББББББББББББ
Trying to use the laser head in a prohibited area.
БББББББББББББББ
БББББББББББББББ
1418 ALTERNATIVE TOOL
Error in management of alternative tools;
БББББББББББББББ
1. Alternative tool and alternative compensa
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
tion group do not match or there is no suit able alternative tool for the programmed tool.
2. An endless chain may also be pro grammed in the combination of alternative X tools. An invalid configuration may poss ibly have been generated via CPL (TC/TD command).
3. The software may also be defective.
ERROR REMEDY
* Successive check points must differ from each
БББББББББББББББ
other.
БББББББББББББББ
БББББББББББББББ
* The third check point must lie on the connecting
line from the first and second check point in
БББББББББББББББ
positive direction at most.
БББББББББББББББ
БББББББББББББББ
* Control reset/cancellation and correction of the
faulty program.
БББББББББББББББ
БББББББББББББББ
* Check the alternative tool combination in the tool
БББББББББББББББ
editor.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check the alternative tool combination in the tool
editor. If combination OK: control reset and pro
БББББББББББББББ
gram the T again in the switching function.
БББББББББББББББ
1427 INVALID X ZERO SHIFT
БББББББББББББББ
Zero shift not approached and G491 is pro
БББББББББББББББ
grammed.
БББББББББББББББ
1428 +X SIDE WRONG (MPP 7513)
Machining in the positive X area is not possible
БББББББББББББББ
during face machining (refer to MPP P7513).
БББББББББББББББ
1429 -X SIDE WRONG (MPP 7513)
БББББББББББББББ
Machining in the negative X area is not poss ible during face machining (refer to MPP
БББББББББББББББ
P7513).
БББББББББББББББ
1440 G92 OR ZERO SHIFT GROUP CHANGED
БББББББББББББББ
A zero shift is programmed while G491 is ac
БББББББББББББББ
tive.
БББББББББББББББ
1441 CAXIS NOT ACTIVE
Caxis machining is not programmed.
БББББББББББББББ
1449 ZERO SHIFT OR COMP. CHANGE FOR
БББББББББББББББ
G491
БББББББББББББББ
G491 is active. Offsets are changed.
БББББББББББББББ
БББББББББББББББ
5 - 13
БББББББББББББББ
* Approach zero shift before G491 is programmed.
БББББББББББББББ
БББББББББББББББ
* Change entry in MPP P7513 or change program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change entry in MPP P7513 or change program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
* Program Caxis machining (G20C...Z...).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Offsets must not be changed with active G491.
Change NC program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1451 T WITH ACTIVE G491
A tool change was programmed with active
БББББББББББББББ
face machining (G491).
БББББББББББББББ
1456 TABLE CHANGE WITH ACTIVE G491
БББББББББББББББ
Comp. and zero offset table switchover with active G491.
БББББББББББББББ
БББББББББББББББ
1457 FALSE PARAMETER IDENTIFIER
False CPL parameter was transferred.
БББББББББББББББ
БББББББББББББББ
Reading a tool compensation table; invalid character read.
БББББББББББББББ
БББББББББББББББ
1458 PERMITTED VALUE RANGE EXCEEDED
Error during readingin:
БББББББББББББББ
The permitted data range is checked when a
БББББББББББББББ
compensation table is read in. It is checked whether the respective limit va
БББББББББББББББ
lues are exceeded, e.g.; limit values of ma
БББББББББББББББ
chine parameters for T, LX, LZ, DX, etc.
БББББББББББББББ
ERROR REMEDY
* Change NC program; program Tword before
БББББББББББББББ
G491.
БББББББББББББББ
БББББББББББББББ
* Change NC program; no comp. or zero offset
tables must be switched when G491 is active.
БББББББББББББББ
БББББББББББББББ
* Change the CPL program.
БББББББББББББББ
БББББББББББББББ
* Correct the table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct the compensation table or the MP
БББББББББББББББ
(P7501..P7510) before reading in again.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
1459 INVALID STRING/TRANSFER ERROR
БББББББББББББББ
Error during readingin: A character was found during readingin of a
БББББББББББББББ
compensation table which was not expected
БББББББББББББББ
at this position. e.g.: KO" was recognized,
БББББББББББББББ
whereby this must be followed by numeric information.
БББББББББББББББ
1463 TOOL NO. NOT DEFINED
БББББББББББББББ
Error during readingin:
БББББББББББББББ
Before the parameters of a tool are written in a line, the No. of the tool must be specified.
БББББББББББББББ
(e.g.: WZ 03...)
БББББББББББББББ
1464 COMPENSATION NO. NOT DEFINED
БББББББББББББББ
Error during readingin:
БББББББББББББББ
Before the parameters of a compensation group can be written in a line, the No. of the
БББББББББББББББ
compensation group must be specified. (e.g.:
БББББББББББББББ
KO 12 LX ...).
БББББББББББББББ
1466 NO LZ VALUE
БББББББББББББББ
It is established in block preparation that a tool (Tword) has no length offset in Z.
БББББББББББББББ
LZ = 0 means tool carrier point!
БББББББББББББББ
БББББББББББББББ
* Repeat readingin (transfer error?); correct table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Repeat readingin (transfer error?); correct table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Repeat readingin (transfer error?); correct table.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Measure tool?
Reenter tool?
БББББББББББББББ
Change programming?
БББББББББББББББ
5 - 14
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1472 NO COMPENSATION GROUP ACTIVE
CPL: TC command
БББББББББББББББ
A TC command without specification of the
БББББББББББББББ
compensation group was programmed but
БББББББББББББББ
no compensation group is active (T0)!
БББББББББББББББ
1473 NO TOOL ACTIVE
БББББББББББББББ
CPL: TD command A TD command without specification of the
БББББББББББББББ
tool was programmed but no tool is active
БББББББББББББББ
(T0)!
БББББББББББББББ
1474 G92 X.. NOT PERMITTED
БББББББББББББББ
Programming error: G94 is not permitted in X
БББББББББББББББ
БББББББББББББББ
1475 TOOL CHANGE ONLY WITH G40
Programming error: G41, G42
БББББББББББББББ
The cutter radius compensation must be
БББББББББББББББ
switched off before the tool change.
БББББББББББББББ
ERROR REMEDY
* Activate tool (compensation group) or change
БББББББББББББББ
TC command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Activate tool or change TD command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change programming.
БББББББББББББББ
БББББББББББББББ
* Program G40 or correct the program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
1480 ALT. COMPENSATION GROUP INVALID
БББББББББББББББ
Programming error: G41, G42
БББББББББББББББ
The cutter radius compensation must be switched off before the tool change.
БББББББББББББББ
БББББББББББББББ
1498 TOOL DATAW1W4 MISSING
KS tables W1W4 not written.
БББББББББББББББ
БББББББББББББББ
1499 INVALID PROGR. IDENTIFIER
Program identifier MACHTYP does not corre
БББББББББББББББ
spond to the permitted values.
БББББББББББББББ
БББББББББББББББ
1500 INVALID TOOL CALL
SD function called with invalid T (K, D)
БББББББББББББББ
numbers. Number is outside the permitted
БББББББББББББББ
value range. Selected feed rate too high.
БББББББББББББББ
БББББББББББББББ
1507 INVALID CHANGE POSITION
No tool change is permitted at the calculated
БББББББББББББББ
change position.
БББББББББББББББ
БББББББББББББББ
* Program G40 or correct the program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Complete tool tables in the KS table.
БББББББББББББББ
БББББББББББББББ
* Use permissible values.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Value range: T 1-99
БББББББББББББББ
K1-999999999
БББББББББББББББ
D 100-99912
* Check feed in MPP.
БББББББББББББББ
БББББББББББББББ
* Check position of the Yaxis and parameter P3 in
БББББББББББББББ
M06.
БББББББББББББББ
1535 INVALID TURNING TOOL
БББББББББББББББ
Machining with the turning tool is not possible
БББББББББББББББ
owing to the correct cutting edge/ milling cutter position.
БББББББББББББББ
БББББББББББББББ
5 - 15
БББББББББББББББ
* Error in the tool table or select different turning
БББББББББББББББ
tool.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1536 ZERO OFFSET NOT APPROACHED
An offset is switched on, but not approached
БББББББББББББББ
with programmed G491.
БББББББББББББББ
БББББББББББББББ
1542 BLOCK SEARCH NOT ALLOWED
БББББББББББББББ
Block search to a block with active G491 is
БББББББББББББББ
not allowed.
БББББББББББББББ
1543 G108 ACTIVE
G491 activated while G108 is active.
БББББББББББББББ
БББББББББББББББ
1544 DISTANCE FROM ZERO POINT
Trying to pass the coordinate origin closer
БББББББББББББББ
than is allowed.
БББББББББББББББ
БББББББББББББББ
1550 G33: LEAD NOT ALLOWED
No lead value programmed in the G33 block.
БББББББББББББББ
Lead of the cutting axis is negative.
БББББББББББББББ
Max. permitted lead exceeded. Min. permitted lead not reached.
БББББББББББББББ
No retraction possible since retraction angle
БББББББББББББББ
same as lead angle.
БББББББББББББББ
ERROR REMEDY
* Change NC program; at least one traversing
БББББББББББББББ
block must be programmed for offset approach
БББББББББББББББ
before G491.
БББББББББББББББ
БББББББББББББББ
* Block search only possible to blocks with G490.
БББББББББББББББ
БББББББББББББББ
* G491 only allowed with G9.
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
Determine allowed" distance using SD (104).
БББББББББББББББ
БББББББББББББББ
* Program at least one lead value.
БББББББББББББББ
* Enter positive lead.
БББББББББББББББ
* Reduce lead. * Increase lead.
БББББББББББББББ
* Change retraction point or retraction angle.
БББББББББББББББ
БББББББББББББББ
1551 SPINDLE SPEED NOT PERMITTED
БББББББББББББББ
Programmed speed outside the permitted
БББББББББББББББ
range.
БББББББББББББББ
1553 G33: RETRACTION NOT PERMITTED
БББББББББББББББ
Retraction movement with sign change in main axis path part.
БББББББББББББББ
БББББББББББББББ
Retraction movement with sign change in
БББББББББББББББ
auxiliary axis path part.
БББББББББББББББ
1553 RETRACTION NOT POSSIBLE
БББББББББББББББ
Retraction movement with sign change in mainaxis path.
БББББББББББББББ
БББББББББББББББ
Retraction movement with sign change in
БББББББББББББББ
auxiliary axis path.
БББББББББББББББ
1554 ALL VARIANTS
No F value is programmed or the value is
БББББББББББББББ
< 0.0001 in G98 block Rapid retraction".
БББББББББББББББ
БББББББББББББББ
The programmed feedrate for G95 is too high.
БББББББББББББББ
БББББББББББББББ
5 - 16
БББББББББББББББ
* Correct spindle speed.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change retraction point or retraction angle.
БББББББББББББББ
БББББББББББББББ
* Change retraction point or retraction angle.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change retraction point or retraction angle.
БББББББББББББББ
БББББББББББББББ
* Change retraction point or retraction angle.
БББББББББББББББ
БББББББББББББББ
* Change NC program with respect to Fvalue.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change programmed feedrate.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1554 FEED NOT PERMITTED
No Fvalue is programmed or the Fvalue is <
БББББББББББББББ
0.0001 in the G98 block Rapid retraction".
БББББББББББББББ
БББББББББББББББ
Feed becomes negative owing to excessively large neg. feed change.
БББББББББББББББ
БББББББББББББББ
Permitted feed exceeded (main axis).
БББББББББББББББ
Permitted feed exceeded (auxiliary axis).
БББББББББББББББ
БББББББББББББББ
Permitted feed not reached.
БББББББББББББББ
Programmed feed for G95 too large.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
1555 NO G96 POSSIBLE
Thread cutting in conjunction with G96 (con
БББББББББББББББ
stant cutting speed).
БББББББББББББББ
1555 NO DIST. PROGRAMMED
БББББББББББББББ
Threadcutting in conjunction with pro
БББББББББББББББ
grammed G96.
БББББББББББББББ
ERROR REMEDY
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct feed change F.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Reduce spindle speed.
БББББББББББББББ
* Reduce spindle speed.
БББББББББББББББ
БББББББББББББББ
* Increase spindle speed.
БББББББББББББББ
* Change programmed feed.
БББББББББББББББ
БББББББББББББББ
* Deactivate G96.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Deactivate G96.
БББББББББББББББ
БББББББББББББББ
1556 SYNC. NOT POSSIBLE
БББББББББББББББ
Spindle synchronisation is not possible:
БББББББББББББББ
- One or both spindles are under automatic
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
control (M5/M19)
- Spindles rotating is different directions
- One spindle is in test mode
- One or both spindles have gear stage ac knowledge
- The 100% speed of the lead spindle can not be reached by the passive spindle in the selected gear stage
- Block search in a phase with synchronous operation
1557 SPINDLE PROG. NOT PERMITTED
Invalid spindle progr. when switching on or
БББББББББББББББ
with synchronisation active.
БББББББББББББББ
1558 SPINDLE INTERF. ERROR
БББББББББББББББ
Invalid interface modification with synchron
БББББББББББББББ
ous mode active.
БББББББББББББББ
1559 M30 WITH SYNC. ACTIVE
БББББББББББББББ
Main program end reached with spindle syn chronisation active.
БББББББББББББББ
БББББББББББББББ
5 - 17
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* G192/292, G193/293, movement M codes, gear
БББББББББББББББ
stage M codes and S values are not allowed.
БББББББББББББББ
БББББББББББББББ
* Only 0 Volts lateral", pot internal/external" and
БББББББББББББББ
pot 100%" can be changed.
БББББББББББББББ
БББББББББББББББ
* Control reset. Change part program; i.e. cancel
synchronisation before M30.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
1577 BARRIERS EXCEEDED
A barrier limiting line is intersected by the cut
БББББББББББББББ
ting edge tip in a traversing movement which
БББББББББББББББ
was processed by block preparation.
БББББББББББББББ
Barrier transgression is recognized at the fol
БББББББББББББББ
lowing elements.
- Barrier transgression at the chuck.
БББББББББББББББ
- Barrier transgression at the steadyrest.
БББББББББББББББ
- Barrier transgression at the tailstock.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
1985 ADDRESS S" MISSING
G875 or G890 programmed without S".
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
ERROR REMEDY
1. Check traversing movement.
БББББББББББББББ
* Is the end point of the traversing movement in
БББББББББББББББ
side a barrier?
БББББББББББББББ
* Does the programmed curve cut a barrier?
* Do not execute traversing movement; change
БББББББББББББББ
program.
2. Barrier points incorrectly measured?
БББББББББББББББ
An excessively large safety distance places re
БББББББББББББББ
strictions on machining.
БББББББББББББББ
* Remeasure barrier points.
3. Check tool measurement.
БББББББББББББББ
* Is the correct tool programmed?
БББББББББББББББ
* Is the compensation group compensation value/
БББББББББББББББ
group correct?
БББББББББББББББ
* Change part program.
БББББББББББББББ
In G875, S" is the distance of the heightcon
БББББББББББББББ
trolled axis (P8006 /53/) until the measurement is
БББББББББББББББ
finished.
БББББББББББББББ
1986 ADDRESS S" OR F" MISSING
G890 programmed without S" and F".
БББББББББББББББ
БББББББББББББББ
2005 CLOSE BRACKETS MISSING
The closing bracket is missing in the NC
БББББББББББББББ
block after an opening bracket.
БББББББББББББББ
2008 FILE NONEXISTENT
БББББББББББББББ
Error during readingin: The file sought by way of the DFS identifier does not exist.
БББББББББББББББ
БББББББББББББББ
2010 FILE ALREADY EXISTS
БББББББББББББББ
The program already exists when DA mode is
БББББББББББББББ
activated. Trying to read in a file during data
БББББББББББББББ
transfer which already exists in the part pro gram memory.
БББББББББББББББ
БББББББББББББББ
The file specified in FIX already exists in the
БББББББББББББББ
part program memory.
БББББББББББББББ
2015 INVALID LEVEL
The selected level contains at least one axis
БББББББББББББББ
which is not applied in the system.
БББББББББББББББ
G20 with more or less than two axis ad
БББББББББББББББ
dresses.
БББББББББББББББ
БББББББББББББББ
Level changed with coordinate transf. acti vated.
БББББББББББББББ
БББББББББББББББ
5 - 18
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct file sought?
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Set FEED HOLD; cancel program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change the file no. in FIXB.
БББББББББББББББ
БББББББББББББББ
* Change selected level.
БББББББББББББББ
БББББББББББББББ
* Program G20 with two axis addresses.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2020 RADIUS > 5000 mm
The workpiece radius is too large for cylinder
БББББББББББББББ
jacket machining.
БББББББББББББББ
2028 INVALID WEIGHTING FACTOR
БББББББББББББББ
Weighting factors are programmed in the
БББББББББББББББ
G114 block which are outside the limit values defined in the MPP (P1014, P1015).
БББББББББББББББ
БББББББББББББББ
2030 CLG VALUE INVALID
Programmed closedloop gain (CLG) outside
БББББББББББББББ
the limit values defined in the MPP.
БББББББББББББББ
2031 G14 WITHOUT AXIS INFO
БББББББББББББББ
Closedloop gain programming without input
БББББББББББББББ
of CLG values.
БББББББББББББББ
2040 G2/3: F/R INVALID
БББББББББББББББ
Feed too large referred to radius.
БББББББББББББББ
ERROR REMEDY
* Reprogram G20 with radius.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Program different weighting factors or change
БББББББББББББББ
MPP.
БББББББББББББББ
БББББББББББББББ
* Change programmed values or limit values.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Program CLG value for min. one axis.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Reduce feed.
БББББББББББББББ
2041 INVALID CIRCLE PARAMETER
No radius (R) must be used with active quad
БББББББББББББББ
rant programming.
БББББББББББББББ
The interpolation parameters have a negative
БББББББББББББББ
sign.
БББББББББББББББ
1. Circle parameters do not match (e.g. dis
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
tance start pointend point > 2)
2. Radius > 100 m.
3. Full circle not permitted for radius pro gramming. 4. No centerpoint coordinates programmed.
Can also occur in limit cases if the radius input is inexact.
2042 G2/3: INVALID NUMBER OF AXES
Too many axes programmed.
БББББББББББББББ
БББББББББББББББ
2043 G5: DIRECTION UNDEFINED
No tangential approach direction can be
БББББББББББББББ
calculated.
БББББББББББББББ
2044 G5: RADIUS TOO LARGE
БББББББББББББББ
Calculated radius too large for tangential ap
БББББББББББББББ
proach.
БББББББББББББББ
2045 G5: AFTER HELICAL
G5 programmed after helical interpolation.
БББББББББББББББ
БББББББББББББББ
5 - 19
* Program the circle center point I, J; I, K or J, K.
БББББББББББББББ
* Program the interpolation parameters I, J, K as
БББББББББББББББ
relative values without sign.
БББББББББББББББ
* Correct circularpath programming.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check MPP 9903, 9912.
БББББББББББББББ
БББББББББББББББ
* Correct part program.
БББББББББББББББ
БББББББББББББББ
* Correct circularpath programming.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct part program.
БББББББББББББББ
БББББББББББББББ
* Correct part program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2046 G5: AFTER LEVEL CHANGE
G5 programmed after level change.
БББББББББББББББ
БББББББББББББББ
2048 UNEQUAL FACTORS
Different scaling factors exist and circular tra
БББББББББББББББ
versing is taking place.
БББББББББББББББ
2049 LEAD TOO LARGE
БББББББББББББББ
Lead greater than 82 degrees.
БББББББББББББББ
No circular component in the movement.
БББББББББББББББ
БББББББББББББББ
2095 ERROR IN ECODE
БББББББББББББББ
Error during readingin:
БББББББББББББББ
Incorrect Ecode value.
БББББББББББББББ
Ecode inputs not permitted for S (PIC), G, K,
БББББББББББББББ
W, V and D files.
БББББББББББББББ
2098 PERM.VARIABLE BLOCKED
БББББББББББББББ
Access by CPL to permanent variable unsuc
БББББББББББББББ
cessful since permanent variable is blocked by the PLC.
БББББББББББББББ
БББББББББББББББ
2101 PROHIB. WORKING AREA AXIS 1 2102 PROHIB. WORKING AREA AXIS 2
БББББББББББББББ
2103 PROHIB. WORKING AREA AXIS 3
БББББББББББББББ
2104 PROHIB. WORKING AREA AXIS 4 2105 PROHIB. WORKING AREA AXIS 5
БББББББББББББББ
2106 PROHIB. WORKING AREA AXIS 6
БББББББББББББББ
2107 PROHIB. WORKING AREA AXIS 7
БББББББББББББББ
2108 PROHIB. WORKING AREA AXIS 8
For G25, G26: The indicated axis is not in the
БББББББББББББББ
permitted working area or leaves the per
БББББББББББББББ
mitted working area with linear interpolation.
БББББББББББББББ
ERROR REMEDY
* Correct part program.
БББББББББББББББ
БББББББББББББББ
* Change scaling factor or do not traverse circular
БББББББББББББББ
blocks (G2, G3).
БББББББББББББББ
БББББББББББББББ
* Reduce lead.
БББББББББББББББ
* Check NC block.
БББББББББББББББ
* Traverse linear axis with G 1.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Correct Ecode values.
БББББББББББББББ
* Do not use an Ecode.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* PLC must reset interlock flag for permanent vari
БББББББББББББББ
ables.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2109 PROHIB. WORKING AREA CIRCLE
БББББББББББББББ
For G25, G26: The permitted working area is Ieft with circular interpolation.
БББББББББББББББ
БББББББББББББББ
2110 WORKING AREA MAX. 3 AXES
For G125, G126: More than 3 axes are pro
БББББББББББББББ
grammed in the definition of the prohibited
БББББББББББББББ
working area.
БББББББББББББББ
2116 NO AXIS COUPLING POSSIBLE
БББББББББББББББ
Trying to activate axis coupling although the two axes are in different positions.
БББББББББББББББ
БББББББББББББББ
5 - 20
БББББББББББББББ
* Check program.
БББББББББББББББ
БББББББББББББББ
* Check program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2120 TOO MANY BLOCKS SUPPRESSED
With active cutter radius compensation, too
БББББББББББББББ
many blocks without traversing movement in
БББББББББББББББ
the active level. More than 6 blocks without
БББББББББББББББ
traversing movement are programmed in total before or after a traversing block.
БББББББББББББББ
БББББББББББББББ
The CPL command WAIT was programmed.
БББББББББББББББ
2121 LEVEL CHANGE ACT. COMP.
A different level is activated via level switch
БББББББББББББББ
over (G17..G20) with active cutter radius
БББББББББББББББ
compensation.
БББББББББББББББ
БББББББББББББББ
With face end interpolation active, tool radius compensation is deselected without move
БББББББББББББББ
ment.
БББББББББББББББ
2122 COLLISION !!
БББББББББББББББ
With active cutter radius compensation: Tool offset radius is greater than full circle radius.
БББББББББББББББ
БББББББББББББББ
The software is not in a position to calculate a
БББББББББББББББ
corrected contour, but cannot recognize any of the other errors.
БББББББББББББББ
БББББББББББББББ
With active collision monitoring: The original
БББББББББББББББ
contour would be violated by execution of the corrected contour.
БББББББББББББББ
БББББББББББББББ
ERROR REMEDY
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program. Move out tool radius com
pensation before G490 (level change) with at
БББББББББББББББ
least one programmed traverse movement.
БББББББББББББББ
БББББББББББББББ
* Change part program or select a different com
pensation value.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 21
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2123 NO INTERSECTION
It is not possible to calculate an intersection
БББББББББББББББ
point between two contour elements offset by
БББББББББББББББ
the cutter radius compensation value with
БББББББББББББББ
active cutter radius compensation.
БББББББББББББББ
The error may occur if:
БББББББББББББББ
БББББББББББББББ
Two elements, line - circle or circle - circle enclose an acute angle and the corrected el
БББББББББББББББ
ements do not have a common intersection
БББББББББББББББ
point.
БББББББББББББББ
With active collision monitoring, if three el
БББББББББББББББ
ements (combination of straight lines and/or
БББББББББББББББ
circles) form a pocket, whereby the 2nd el
БББББББББББББББ
ement can no longer be executed owing to the compensation value and there is no inter
БББББББББББББББ
section point between the 1st and 3rd el
БББББББББББББББ
ements.
БББББББББББББББ
Owing to computing inaccuracies in calcula
БББББББББББББББ
tion of the corrected elements if the elements
БББББББББББББББ
possess tangential transitions.
БББББББББББББББ
ERROR REMEDY
* Change part program or select a different com
БББББББББББББББ
pensation value.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2125 INVALID COMPENSATION VALUE
БББББББББББББББ
An invalid Gfunction was programmed with active spatial tool offset G43/44.
БББББББББББББББ
БББББББББББББББ
Incorrect compensation value.
БББББББББББББББ
Radius compensation value too large or too
БББББББББББББББ
small.
БББББББББББББББ
БББББББББББББББ
An invalid value is assigned to a variable in a KS table with a CPL TD command. The maxi
БББББББББББББББ
mum permitted value is defined by the format
БББББББББББББББ
agreed for the variable in the definition part of
БББББББББББББББ
the KS table.
БББББББББББББББ
2126 SEVERAL ZERO SHIFTS ACTIVE
Wrong parameters in CPL command FXC.
БББББББББББББББ
БББББББББББББББ
2131 COMP. ENTRY WITH CIRCLE
БББББББББББББББ
With active cutter radius compensation: The 1st traversing movement after activation
БББББББББББББББ
of the cutter radius compensation logic via
БББББББББББББББ
G41/G42 is a circular movement.
БББББББББББББББ
5 - 22
БББББББББББББББ
* Change Gfunctions in the part program.
БББББББББББББББ
БББББББББББББББ
* Check and change compensation values.
БББББББББББББББ
* Change radius compensation value in part pro
БББББББББББББББ
gram or change corresponding MP.
БББББББББББББББ
БББББББББББББББ
* Change CPL program, possibly incorporate
check.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check and change parameters in the CPL com
БББББББББББББББ
mand in the part program.
БББББББББББББББ
БББББББББББББББ
* Change part program.
Program linear movement.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2132 COMP. CANCEL WITH CIRCLE
With active cutter radius compensation:
БББББББББББББББ
The 1st traversing movement after deactiva
БББББББББББББББ
tion of the cutter radius compensation logic
БББББББББББББББ
via G40 is a circular movement.
БББББББББББББББ
2133 CHANGE G41/42 WITH CIRCLE
With active cutter radius compensation:
БББББББББББББББ
The 1st traversing movement after a change
БББББББББББББББ
from G41 to G42 or from G42 to G41 is a circular movement.
БББББББББББББББ
БББББББББББББББ
2134 COMP. ACT. AT PROGRAM END
With active cutter radius compensation:
БББББББББББББББ
The cutter radius compensation is still active
БББББББББББББББ
at the end of the main program. The main program cannot be executed up to the end.
БББББББББББББББ
БББББББББББББББ
2136 GADDR INVALID FOR G41/42
With active cutter radius compensation:
БББББББББББББББ
One of the following Gaddresses is pro
БББББББББББББББ
grammed:
- Set zero point G92.
БББББББББББББББ
- Inchmetric switchover G70 to G71 or G71
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2136 GADR INVALID FOR G41/G42
БББББББББББББББ
БББББББББББББББ
to G70.
- Switchover of the active level with G17 ... G20.
- Thread cutting G33.
- Travel to reference point G74, G174, G274.
- Rapid retraction G98/G99.
G32 is programmed with active cutter radius compensation.
ERROR REMEDY
* Change part program. Program linear move
БББББББББББББББ
ment.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program. Linear movement after
БББББББББББББББ
change.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program; G40 at main program
БББББББББББББББ
end.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* First cancel cutter radius compensation.
БББББББББББББББ
БББББББББББББББ
2137 SINGLE BLOCK WITH G41/42
БББББББББББББББ
Program testing in single block" is active with active cutter radius compensation.
БББББББББББББББ
БББББББББББББББ
2138 NO COMPENSATION ACT.
CPL command TC programmed without
БББББББББББББББ
previously activating a compensation table.
БББББББББББББББ
Wrong parameters in CPL command FXC.
БББББББББББББББ
БББББББББББББББ
5 - 23
БББББББББББББББ
* Select subsequent block or single step.
БББББББББББББББ
БББББББББББББББ
* Check and change part program.
БББББББББББББББ
БББББББББББББББ
* Check and change parameters in the CPL com
БББББББББББББББ
mand in the part program.
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2140 MODAL SUBROUTINE IS ACTIVE
It is possible to jump to a subroutine or jump
БББББББББББББББ
back into the main program in direct execu
БББББББББББББББ
tion mode only if no modal subroutine is ac
БББББББББББББББ
tive:
БББББББББББББББ
A subroutine is called although a modal sub
БББББББББББББББ
routine is active.
БББББББББББББББ
A subroutine is quit although a modal subrou
БББББББББББББББ
tine is still active.
БББББББББББББББ
2142 NO M2 OR M30
БББББББББББББББ
An M2 or an M30 is missing in the main pro gram or in a subroutine.
БББББББББББББББ
БББББББББББББББ
2144 MEMORY IS OCCUPIED
The memory has not been released for the
БББББББББББББББ
link table which is to be created.
БББББББББББББББ
The memory is occupied by other l/O actions (reading in etc.).
БББББББББББББББ
2145 TOO MANY VARIABLES
БББББББББББББББ
The memory requirement for the global vari
БББББББББББББББ
ables or for the local variables of a subroutine is greater than 32767 bytes.
БББББББББББББББ
БББББББББББББББ
2150 INSUFFICIENT MEMORY
БББББББББББББББ
Each PRN instruction within a DLG sequence
БББББББББББББББ
requires memory space in the system heap. However, the memory is full.
БББББББББББББББ
БББББББББББББББ
There is not sufficient memory space in order
БББББББББББББББ
to create a link table.
БББББББББББББББ
2151 VARIABLE TYPE WRONG
A variable name is present several times with
БББББББББББББББ
different types.
БББББББББББББББ
ERROR REMEDY
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Deactivate modal subroutine with G80.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Insert M2 or M30.
БББББББББББББББ
БББББББББББББББ
* Enable memory and restart link.
БББББББББББББББ
* Abort the other l/O action.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program; DIM instruction possibly
БББББББББББББББ
too large.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Enable system heap again with CLEAR LOGIC.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Create memory space by control reset or by
БББББББББББББББ
deleting files and restart linking.
БББББББББББББББ
* Check variable name in CPL program.
БББББББББББББББ
БББББББББББББББ
2152 SUBROUTINE NONEXISTENT
БББББББББББББББ
A subroutine call is programmed for which there is no subroutine.
БББББББББББББББ
БББББББББББББББ
Trying to read the local data of a subroutine
БББББББББББББББ
which is not present in the link table.
БББББББББББББББ
Fix was called with a nonexistent file no.
БББББББББББББББ
БББББББББББББББ
Go block function/reentry was selected. A subroutine is specified in MPP P4014. There
БББББББББББББББ
is either a subroutine call or tool change call
БББББББББББББББ
in the main program, but the subroutine does
БББББББББББББББ
not
exist.
БББББББББББББББ
5 - 24
БББББББББББББББ
* Change part program or create subroutine.
БББББББББББББББ
* Delete link table, perform linking again. If this
БББББББББББББББ
error occurs during runtime, an internal software
БББББББББББББББ
error exists.
БББББББББББББББ
* Change Fix no. or read in missing image file via
БББББББББББББББ
data I/O.
БББББББББББББББ
* Create subroutine with the part program number
which is defined in the MPP or set MPP P101 to
БББББББББББББББ
0".
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2153 NESTING TOO DEEP
An expression in a CPL instruction is nested
БББББББББББББББ
too deep.
БББББББББББББББ
БББББББББББББББ
2154 VARIABLE NOT OCCUPIED
Read access is performed to a variable which
БББББББББББББББ
has not yet had a value assigned.
БББББББББББББББ
Write access is made to a field variable for
БББББББББББББББ
which no DIM instruction has yet been run
БББББББББББББББ
through.
БББББББББББББББ
The index limits of a real field variable were
БББББББББББББББ
not observed.
БББББББББББББББ
БББББББББББББББ
A variable is still undefined, i.e. no value was assigned to it previously.
БББББББББББББББ
БББББББББББББББ
2155 WRONG INDEX
The index limits of a field variable were not
БББББББББББББББ
observed.
БББББББББББББББ
БББББББББББББББ
2157 SELFCALL PROHIBITED
The main program or a subroutine calls itself
БББББББББББББББ
or is called again in a deeper nesting.
БББББББББББББББ
ERROR REMEDY
* Reduce expression by means of local variables.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check CPL program.
БББББББББББББББ
БББББББББББББББ
* Check CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change field variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change field variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change subroutine call structure.
БББББББББББББББ
БББББББББББББББ
2158 INVALID STATEMENT
БББББББББББББББ
It was attempted to write the external zero
БББББББББББББББ
shift values with CPL command FXC or the PLC is not connected via a word coupler.
БББББББББББББББ
One of the commands OPENW, OPENR,
БББББББББББББББ
CLOSE, REWRITE, INP# and PRN# (file ac
БББББББББББББББ
cess) is programmed in a DLG sequence.
БББББББББББББББ
The EOF command is used in a DLG se
БББББББББББББББ
quence.
БББББББББББББББ
The =" symbol is missing after one of the
БББББББББББББББ
following commands: IC, MIC, FXC, TC or TD.
БББББББББББББББ
БББББББББББББББ
A CPL instruction is not yet terminated at the end of the program.
БББББББББББББББ
БББББББББББББББ
The last block in a program is a CPL block
БББББББББББББББ
and it does not end with a <LF>.
БББББББББББББББ
2159 THEN MISSING
БББББББББББББББ
The THEN" is missing after the IF" in front of the Boolean expression.
БББББББББББББББ
БББББББББББББББ
5 - 25
БББББББББББББББ
* Check part program and change if necessary or
БББББББББББББББ
check connection of PLC.
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change IF instruction.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2160 ENDIF MISSING
The ENDIF" is missing after the instruction
БББББББББББББББ
part of IF...THEN" or ELSE". Particularly also
БББББББББББББББ
if ENDIF"s are missing at the end of the pro
БББББББББББББББ
gram.
БББББББББББББББ
2161 WRONG BRANCH DESTINATION
The GOTO instruction is followed by someth
БББББББББББББББ
ing other than an NC block number, an in
БББББББББББББББ
teger constant, a real constant or a CPL label.
БББББББББББББББ
2162 UNTIL MISSING
The UNTIL" is missing after the instruction
БББББББББББББББ
part of REPEAT". Particularly also if UNTIL"s
БББББББББББББББ
are missing at the program end.
БББББББББББББББ
2163 TO MISSING
БББББББББББББББ
TO" is missing after FOR" after the instruc tion.
БББББББББББББББ
БББББББББББББББ
2164 NEXT MISSING
БББББББББББББББ
The NEXT" is missing after the expression
БББББББББББББББ
following the TO". Particularly also if
БББББББББББББББ
NEXT"s are missing at the program end.
БББББББББББББББ
ERROR REMEDY
* Check IF instructions and correct if necessary.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change GOTO instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check REPEAT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check FOR instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check FOR instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2165 DO MISSING
БББББББББББББББ
The DO" is missing after WHILE" after the
БББББББББББББББ
Boolean expression.
БББББББББББББББ
2166 END MISSING
The END" is missing after WHILE...DO"
БББББББББББББББ
after the instruction part. Particularly also if
БББББББББББББББ
END"s are missing at the program end.
БББББББББББББББ
2167 = MISSING
БББББББББББББББ
The =" is missing for write access of the COMcommand.
БББББББББББББББ
The =" symbol is missing after a variable, a
БББББББББББББББ
feed variable, a variable after FOR" or after
БББББББББББББББ
COM" (write access).
БББББББББББББББ
БББББББББББББББ
* Check WHILE instruction.
БББББББББББББББ
БББББББББББББББ
* Check WHILE instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
* Change corresponding instructions.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 26
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2168 INADMISSIBLE VARIABLE
The parameter Program name" is not of the
БББББББББББББББ
type String" for the OPENW command.
БББББББББББББББ
БББББББББББББББ
The expression on the right side is not of the type integer, real or doubleprecision real for
БББББББББББББББ
write access to the COM command.
БББББББББББББББ
БББББББББББББББ
The subroutine parameter is of the type In teger", but the transfer parameter is of the
БББББББББББББББ
type  Real".
БББББББББББББББ
БББББББББББББББ
Incorrect variable type or inadmissible com pensation value in CPL command TC.
БББББББББББББББ
БББББББББББББББ
Variable in CPL command possesses wrong
БББББББББББББББ
type.
БББББББББББББББ
An expression of the type Real" is assigned
БББББББББББББББ
to a CPL TD command.
БББББББББББББББ
A global variable does not start with a letter or
БББББББББББББББ
number after the #".
БББББББББББББББ
БББББББББББББББ
A field variable is programmed without corre sponding DIM instruction.
БББББББББББББББ
БББББББББББББББ
No variable follows FOR".
БББББББББББББББ
No field variable follows DIM".
БББББББББББББББ
БББББББББББББББ
The expression on the right side of the IC in
БББББББББББББББ
struction is not of the type Boolean".
БББББББББББББББ
An expression is assigned to the MIC com
БББББББББББББББ
mand which is not of the type Integer" .
БББББББББББББББ
A second DIM instruction was programmed
БББББББББББББББ
with the same variable, but with different
БББББББББББББББ
memory requirements.
БББББББББББББББ
ERROR REMEDY
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change type of transfer parameter or type of
subroutine parameter.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check and change part program.
БББББББББББББББ
БББББББББББББББ
* Check and change part program.
БББББББББББББББ
БББББББББББББББ
* Change type of expression on the right side to 
БББББББББББББББ
Integer".
БББББББББББББББ
* Change name of global variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Insert DIM instruction.
БББББББББББББББ
БББББББББББББББ
* Change FOR instruction.
БББББББББББББББ
* Change DIM instruction.
БББББББББББББББ
БББББББББББББББ
* Change IC instruction.
БББББББББББББББ
БББББББББББББББ
* Change MIC command.
БББББББББББББББ
БББББББББББББББ
* Change corresponding DIM instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 27
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2169 ) MISSING
The bracket is not closed [)"] after the pro
БББББББББББББББ
gram identifier TTY1  or TTY2" for the
БББББББББББББББ
OPENR or the OPENW command.
БББББББББББББББ
The bracket is not closed [)"] after the pro
БББББББББББББББ
gram identifier TTY" and the file No. for the
БББББББББББББББ
OPENR or the OPENW command.
БББББББББББББББ
The bracket is not closed [)"] after the pro
БББББББББББББББ
gram identifier or after the file No. for the
БББББББББББББББ
OPENR command.
БББББББББББББББ
The bracket is not closed for one of the fol
БББББББББББББББ
lowing CPL instructions: CIR, COL, FIL, GMD,
БББББББББББББББ
GWD, INP, LIN, MWD.
БББББББББББББББ
The bracket is not closed for a field variable within a PRN instruction.
БББББББББББББББ
The bracket is not closed [)"] after the file
БББББББББББББББ
No. for the OPENR command.
БББББББББББББББ
The bracket is not closed [)"] after the pro
БББББББББББББББ
gram identifier for the OPENR command.
БББББББББББББББ
There is no length or the bracket is not closed
БББББББББББББББ
for the OPENW command after the program
БББББББББББББББ
identifier or the file No. or there is no program
БББББББББББББББ
name or the bracket is not closed [)"] after the length or the bracket is not closed after
БББББББББББББББ
the program name [)"].
БББББББББББББББ
БББББББББББББББ
The bracket is not closed [)"] or there is no comma (,") after the first parameter of the
БББББББББББББББ
CLOSE or REWRITE command.
БББББББББББББББ
БББББББББББББББ
Too many parameters are specified or the bracket is not closed [)"] for the COM com
БББББББББББББББ
mand.
БББББББББББББББ
БББББББББББББББ
The bracket is not closed:
- in the parameter list of a CPL instruction.
БББББББББББББББ
- in a field variable.
БББББББББББББББ
- in a nested expression.
БББББББББББББББ
A ]" follows the CALL subroutine call.
БББББББББББББББ
БББББББББББББББ
5 - 28
ERROR REMEDY
* Change OPEN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change OPEN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change OPENR command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change OPENR command.
БББББББББББББББ
БББББББББББББББ
* Change OPENR command.
БББББББББББББББ
БББББББББББББББ
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program. * Change field variable.
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2170 INVALID EXPRESSION
A CPL expression is programmed in an NC
БББББББББББББББ
word of the address types 2, 3, 5, 6, 7, 8, 10
БББББББББББББББ
or 11 (MP 9000) with variable address which
БББББББББББББББ
returns a value other than integer, real or doubleprecision real, e.g.: X[A$].
БББББББББББББББ
БББББББББББББББ
A CPL real expression is programmed in an
БББББББББББББББ
NC word of the address types 2, 5, 7, 8 or 11 (MP 9000) with variable address which is
БББББББББББББББ
2147483647 or 2147483648.
БББББББББББББББ
The specified value for asynchronous axes is outside the internal representation range.
БББББББББББББББ
БББББББББББББББ
No number follows the ." of a real constant.
БББББББББББББББ
There is no variable or no bracket is opened
БББББББББББББББ
[("] after NOT".
БББББББББББББББ
CPL commands are used in an expression
БББББББББББББББ
which do not return any value, e.g.:
БББББББББББББББ
A%+OPENR...
БББББББББББББББ
No bracket is opened [("] after a NOT" in
БББББББББББББББ
the first parameter of WAIT.
БББББББББББББББ
БББББББББББББББ
An expression of the type Boolean" or String" is programmed in a variable address
БББББББББББББББ
of an NC block.
БББББББББББББББ
БББББББББББББББ
Something else is programmed as well as the expression in a variable address of an NC
БББББББББББББББ
block, e.g.: X[A, ].
БББББББББББББББ
БББББББББББББББ
Something else is programmed in a block as
БББББББББББББББ
well as the CALL instruction.
БББББББББББББББ
A character field was used for programming a
БББББББББББББББ
variable address.
БББББББББББББББ
There is no integer constant after the CALL
БББББББББББББББ
subroutine call.
БББББББББББББББ
2171 - NOT PERMITTED
БББББББББББББББ
A Boolean or string expression has a nega tive sign.
БББББББББББББББ
БББББББББББББББ
5 - 29
ERROR REMEDY
* Change CPL expression in part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Specify a permitted value.
БББББББББББББББ
БББББББББББББББ
* Supplement real constant.
БББББББББББББББ
* Change NOT expression.
БББББББББББББББ
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL block.
БББББББББББББББ
БББББББББББББББ
* Change CPL expression.
БББББББББББББББ
БББББББББББББББ
* A variable subroutine call is not permitted. Insert
БББББББББББББББ
integer constant!
БББББББББББББББ
БББББББББББББББ
* Change CPL expression.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2172 TYPE MUST BE BIT
The expression after NOT" is not of the type
БББББББББББББББ
Boolean".
БББББББББББББББ
БББББББББББББББ
The comparison with the IC command is not of the type Boolean".
БББББББББББББББ
БББББББББББББББ
The condition in the IF, WHILE or REPEAT
БББББББББББББББ
instruction is not of the type Boolean".
БББББББББББББББ
2173 INVALID OPERAND
An expression was used for the +", -",
БББББББББББББББ
operation which is not of the type Integer",
БББББББББББББББ
Real" or Doubleprecision real".
БББББББББББББББ
An expression is used for the AND", OR" or
БББББББББББББББ
XOR" operation which is not of the type
БББББББББББББББ
Boolean".
БББББББББББББББ
2174 INVALID RELATION
БББББББББББББББ
An expression is used for the  < , " > ", <=" or >=" operation which is not of the ;;
БББББББББББББББ
type Integer", Real" or Doubleprecision
БББББББББББББББ
real".
БББББББББББББББ
For the  = " or  < > " operation, the first
БББББББББББББББ
operand is of the type Integer", Real" or
БББББББББББББББ
Doubleprecision real" and the second of the
БББББББББББББББ
type Boolean" or String", or the first V oper and is of the type Boolean" and the second
БББББББББББББББ
is of a type which is not Boolean" or not
БББББББББББББББ
NUL", or the first parameter is of the type
БББББББББББББББ
String" and the second of a type which is not String" or not NUL".
БББББББББББББББ
БББББББББББББББ
2175 INVALID ASSIGNMENT
The variable on the left side of the type
БББББББББББББББ
Doubleprecision real" and the data type
БББББББББББББББ
(3rd parameter) is not D" for read access of the COM command.
БББББББББББББББ
БББББББББББББББ
The variable on the left side is of the type
БББББББББББББББ
Real" and the data type (3rd parameter) is not R" for read access of the COM com
БББББББББББББББ
mand.
БББББББББББББББ
БББББББББББББББ
The variable on the left side is of the type In teger" and the data type (3rd parameter) is
БББББББББББББББ
not I", W" or B" for read access of the
БББББББББББББББ
COM command.
БББББББББББББББ
The variable on the left side is not of the type
БББББББББББББББ
Integer", Real" or Doubleprecision real"
БББББББББББББББ
for read access of the COM command.
БББББББББББББББ
5 - 30
ERROR REMEDY
* Change NOT expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
* Change corresponding instruction.
БББББББББББББББ
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change expression.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
The expression on the right side is of the type Doubleprecision real" and the data type
БББББББББББББББ
(3rd parameter) is not D" or R" for write ac
БББББББББББББББ
cess of the COM command.
БББББББББББББББ
The expression on the right side is of the type
БББББББББББББББ
Integer" and the data type (3rd parameter) is
БББББББББББББББ
not B", W" or I" for write access of the
БББББББББББББББ
COM command.
БББББББББББББББ
For assignment =", the left variable is of the
БББББББББББББББ
type Integer" and the expression is not of the
БББББББББББББББ
type Integer" or NUL", or the left variable is of the type Real" or Doubleprecision real"
БББББББББББББББ
and the expression is not of the type In
БББББББББББББББ
teger", Real" or Doubleprecision real" or
БББББББББББББББ
NUL", or the left variable is of the type Bool ean" and the expression is not of the type
БББББББББББББББ
Boolean" or NUL" or the left variable is of
БББББББББББББББ
the type String" and the expression is not of
БББББББББББББББ
the type String" or NUL" .
БББББББББББББББ
2176 ] MISSING
БББББББББББББББ
The closing square bracket is missing in an IC block for an AXP command, a variable ad
БББББББББББББББ
dress or a parameter list.
БББББББББББББББ
БББББББББББББББ
2177 ( MISSING
The opening bracket is missing for one of the
БББББББББББББББ
following CPL instructions: CIR, COL, FIL,
БББББББББББББББ
GMD, GWD, LIN, MWD.
БББББББББББББББ
The opening bracket is missing for one of the
БББББББББББББББ
commands CLOSE, COM, DELETE INP#,
БББББББББББББББ
OPENR, OPENW, PRN# or REWRITE.
БББББББББББББББ
The opening bracket is missing for a field
БББББББББББББББ
variable.
БББББББББББББББ
БББББББББББББББ
The opening bracket is missing for one of the following CPL commands: ABS, ACOS, ASIN,
БББББББББББББББ
ATAN, AXO, AXP, BCD, BIN, CHR, COS,
БББББББББББББББ
CPOS, EOF, IC, INT, MPOS, PPOS, ROUND,
БББББББББББББББ
SD, SIN, SQRT, TAN, TC, TD, TXC or TXT.
БББББББББББББББ
2178 BLOCK NONEXISTENT
БББББББББББББББ
No branch destination is programmed in the G23/G24 block.
БББББББББББББББ
БББББББББББББББ
An NC block does not exist as the branch
БББББББББББББББ
destination of a G23/G24 block or a GOTO instruction
БББББББББББББББ
БББББББББББББББ
5 - 31
ERROR REMEDY
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change assignment.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change field variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding CPL command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2179 LINE NONEXISTENT
A CPL block does not exist as a branch des
БББББББББББББББ
tination of a GOTO instruction.
БББББББББББББББ
2180 LABEL NONEXISTENT
БББББББББББББББ
A LABEL does not exist as the branch des tination of a GOTO instruction.
БББББББББББББББ
БББББББББББББББ
2181 INVALID FIELD LIMIT
The DIM instruction possesses a field limit >
БББББББББББББББ
32767 or the field limit is not programmed as
БББББББББББББББ
an integer constant.
БББББББББББББББ
The DIM instruction for a character field has a
БББББББББББББББ
field limit > 127 or < 1.
БББББББББББББББ
1. SD (2 ...): The 2nd parameter is < 1 or > 3
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2182 INVALID FIELD TYPE
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
2183 INVALID FIELD INDEX
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
or more than 2 parameters are pro grammed.
2. SD (5...): The 2nd parameter is < 1 or > 3 or the 3rd parameter is < 1 or > 2.
3. SD (10....): The 2nd parameter is < 1 or >
2 or more than 2 parameters are pro grammed.
4. SD (11...): The 2nd parameter is < 1 or > 2 or the 3rd parameter is < 1 or > 2.
5. SD (12....): The 2nd parameter is < 1 or >
2 or more than 2 parameters are pro grammed.
6. CPOS command: The specified axis is an asynchronous axis with external setpoint input.
The field variable possesses a field variable which is not Real" or Integer" in the DIM instruction.
A parameter of a field variable or a parameter of one of the following CPL commands is not of the type Integer" or Real": AXO, BCD, BIN, CPOS, FXC, IC, MPOS, PPOS, SD, TC or TD.
5 - 32
ERROR REMEDY
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change DIM instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change DIM instruction.
БББББББББББББББ
БББББББББББББББ
* Change parameter correspondingly.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPOS command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change DIM instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2184 INVALID PARAMETER
The group number (1st parameter) of an SD
БББББББББББББББ
function is not permitted.
БББББББББББББББ
БББББББББББББББ
SD(1,...): The second parameter is less than 1 or greater than 32 or the third parameter is
БББББББББББББББ
less than 1 or greater than 2.
БББББББББББББББ
БББББББББББББББ
SD(3,...): The second parameter is less than 1 or greater than 2 or more than two para
БББББББББББББББ
meters are programmed.
БББББББББББББББ
БББББББББББББББ
SD(4,...): The second parameter is less than 1 or greater than 2 or more than two para
БББББББББББББББ
meters are programmed.
БББББББББББББББ
БББББББББББББББ
SD(6,...): The second parameter is less than 1 or greater than 7 or more than two para
БББББББББББББББ
meters are programmed.
БББББББББББББББ
БББББББББББББББ
SD(8): More than one parameter is pro grammed.
БББББББББББББББ
БББББББББББББББ
SD(9): More than one parameter is pro
БББББББББББББББ
grammed.
БББББББББББББББ
SD(13): More than one parameter is pro
БББББББББББББББ
grammed.
БББББББББББББББ
AXO, CPOS, MPOS, PPOS: The specified
БББББББББББББББ
axis is not defined.
БББББББББББББББ
БББББББББББББББ
IC command: The interface bit (1st para meter) is outside the range permitted in the
БББББББББББББББ
MPP P4010 for write access or is < 0 or >
БББББББББББББББ
255 for read access.
БББББББББББББББ
AXP instruction: The specified axis is not de
БББББББББББББББ
fined.
БББББББББББББББ
БББББББББББББББ
AXP instruction: The specified axis is already programmed in the NC block.
БББББББББББББББ
БББББББББББББББ
A parameter of the commands CIR, COL, FIL,
БББББББББББББББ
LIN or one of the first two parameters of the DSP command is greater than 2147483647 or
БББББББББББББББ
less than -2147483648.
БББББББББББББББ
БББББББББББББББ
CIR command: The fifth parameter Direction of rotation" is not 0 or 1.
БББББББББББББББ
БББББББББББББББ
COL command: One of the three possible
БББББББББББББББ
parameters is exactly 8, exactly 9, less than 0 or greater than 17.
БББББББББББББББ
5 - 33
ERROR REMEDY
* Change SD function.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD(1,...).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD(3,...).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD(4,...).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD(6,...).
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD(8,...).
БББББББББББББББ
БББББББББББББББ
* Change SD(9,...).
БББББББББББББББ
БББББББББББББББ
* Change SD(13,...).
БББББББББББББББ
БББББББББББББББ
* Change axis number.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change IC command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change AXP instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CIR command.
БББББББББББББББ
БББББББББББББББ
* Change COL command.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
FIL command: The third parameter Filling pattern" is less than 0 or greater than 5 or the
БББББББББББББББ
fourth or possible 5th parameter is exactly 8,
БББББББББББББББ
exactly 9, less than 0 or greater an 17.
БББББББББББББББ
GMD command: The parameter is less than 0
БББББББББББББББ
or greater than 4.
БББББББББББББББ
БББББББББББББББ
GWD command: The first parameter is greater than or equal to the second one or
БББББББББББББББ
the third parameter is greater than or equal to
БББББББББББББББ
the fourth one or the first is less than 0 or the
БББББББББББББББ
third is less than 0 or the second is greater than 511 or the fourth is greater than 359.
БББББББББББББББ
БББББББББББББББ
MWD command: The first parameter is
БББББББББББББББ
greater than or equal to the second one or the third parameter is greater than or equal to
БББББББББББББББ
the fourth one.
БББББББББББББББ
БББББББББББББББ
The parameter of the CHR$ command is not of the type Integer".
БББББББББББББББ
БББББББББББББББ
The parameter of the CHR$ command is less
БББББББББББББББ
than 0 or greater than 255.
БББББББББББББББ
The first letter of the third parameter of the
БББББББББББББББ
COM command is not B", D", I", R" or
БББББББББББББББ
W".
БББББББББББББББ
Trying to convert a value < 0 or a value >
БББББББББББББББ
99999999 for BINBCD conversion.
БББББББББББББББ
Trying to convert single or doubleprecision
БББББББББББББББ
real values in BINBCD or BCDBIN conver
БББББББББББББББ
sion.
БББББББББББББББ
Wrong parameters in CPL command TC for
БББББББББББББББ
table number or compensation selection
БББББББББББББББ
number or compensation value.
БББББББББББББББ
Wrong parameters in CPL command FXC for
БББББББББББББББ
zero shift table or zero shift number or axis
БББББББББББББББ
number.
БББББББББББББББ
Wrong number of parameters for the CPL TD
БББББББББББББББ
command.
БББББББББББББББ
БББББББББББББББ
5 - 34
ERROR REMEDY
* Change FIL command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change GMD command.
БББББББББББББББ
БББББББББББББББ
* Change GWD command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change MWD command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CHR$ command.
БББББББББББББББ
БББББББББББББББ
* Change CHR$ command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Only convert values between 0..99999999.
БББББББББББББББ
БББББББББББББББ
* Convert only integer values with the value range
БББББББББББББББ
0..99999999.
БББББББББББББББ
БББББББББББББББ
* Check parameters in the CPL command TC in
БББББББББББББББ
the part program and change if necessary.
БББББББББББББББ
БББББББББББББББ
* Check parameters in the CPL command FXC in
БББББББББББББББ
the part program and change if necessary.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
The 1st or 2nd parameter is outside the per mitted range.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
The parameter of the GMD command is not of the type Integer".
БББББББББББББББ
БББББББББББББББ
The four parameters of the GWD command
БББББББББББББББ
are not of the type Integer" or fewer than four are programmed.
БББББББББББББББ
БББББББББББББББ
The four parameters of the MWD command
БББББББББББББББ
are not of the type Integer" or Real" or fewer are programmed.
БББББББББББББББ
БББББББББББББББ
The three possible parameters of the COL
БББББББББББББББ
command are not of the type Integer".
БББББББББББББББ
The four possible parameters of the LIN com
БББББББББББББББ
mand are not of the type Integer" or Real".
БББББББББББББББ
The six possible parameters of the CIR com
БББББББББББББББ
mand are not of the type Integer" or Real".
БББББББББББББББ
БББББББББББББББ
The first two parameters of the FIL command are not of the type Integer" or Real" or the
БББББББББББББББ
third, fourth or possible fifth parameter is not
БББББББББББББББ
of the type Integer".
БББББББББББББББ
The OPENW command has more than five
БББББББББББББББ
parameters.
БББББББББББББББ
БББББББББББББББ
The OPENR command has more than three parameters.
БББББББББББББББ
БББББББББББББББ
The DELETE command has more than two
БББББББББББББББ
parameters.
БББББББББББББББ
The CLOSE or REWRITE command has more
БББББББББББББББ
than one parameter.
БББББББББББББББ
The program name of the OPENW command
БББББББББББББББ
is not of the type String".
БББББББББББББББ
БББББББББББББББ
The file No. or the length in the OPENR or OPENW command is not of the type Integer"
БББББББББББББББ
.
БББББББББББББББ
5 - 35
ERROR REMEDY
* Permissible range:
1st parameter:
БББББББББББББББ
Minimum: 1
БББББББББББББББ
Maximum: number of variables in the KS table
БББББББББББББББ
2nd parameter: Minimum: 1
БББББББББББББББ
Maximum: number of groups in the KS table
БББББББББББББББ
БББББББББББББББ
* Change GMD command.
БББББББББББББББ
БББББББББББББББ
* Change GWD command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change MWD command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COL command.
БББББББББББББББ
БББББББББББББББ
* Change LIN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CIR command.
БББББББББББББББ
БББББББББББББББ
* Change FIL command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
* Change OPENR command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change DELETE command.
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
The DELETE, CLOSE or REWRITE command has more than one parameter.
БББББББББББББББ
БББББББББББББББ
One of the first two parameters of the COM
БББББББББББББББ
command is not of the type Integer".
БББББББББББББББ
The third parameter of the COM command is
БББББББББББББББ
not of the type String".
БББББББББББББББ
The third parameter of the COM command is
БББББББББББББББ
a string constant and does not start with a
БББББББББББББББ
B", D", I", R" or W".
БББББББББББББББ
The third parameter of the COM command is
БББББББББББББББ
not a variable and not a string constant.
БББББББББББББББ
БББББББББББББББ
One of the following CPL commands has more than one parameter: AXO, BCD, BIN,
БББББББББББББББ
CPOS, IC, MPOS or PPOS.
БББББББББББББББ
БББББББББББББББ
The SD command has more than 2 parameters.
БББББББББББББББ
One of the following CPL commands has
БББББББББББББББ
more than three parameters: TC, TD or FXC.
БББББББББББББББ
The first parameter of one of the following
БББББББББББББББ
commands is not of the type Integer": CHR,
БББББББББББББББ
EOF or TXT.
БББББББББББББББ
The first parameter of one of the following
БББББББББББББББ
commands is not of the type Integer", Real"
БББББББББББББББ
or Doubleprecision real": ABS, ACOS,
БББББББББББББББ
ASIN, ATAN, COS, INT, ROUND, SIN, SQRT or TAN.
БББББББББББББББ
БББББББББББББББ
The parameter of the EOF command is not a
БББББББББББББББ
variable and is not an integer constant.
БББББББББББББББ
An integer constant in the EOF command
БББББББББББББББ
does not consist of only one digit.
БББББББББББББББ
WAIT instruction: The first parameter is a vari
БББББББББББББББ
able and not equal to the fixed predefined vari
БББББББББББББББ
ables ACTIVE or READY at this point.
БББББББББББББББ
WAIT instruction: The first parameter is not a
БББББББББББББББ
variable and does not start with IC" or NOT".
БББББББББББББББ
БББББББББББББББ
WAIT instruction: There is no comma (,") or the bracket is not closed [)"] after the IC query or
БББББББББББББББ
NOT expression in the first parameter.
БББББББББББББББ
БББББББББББББББ
WAIT instruction: The second or third para meter is not of the type Integer".
БББББББББББББББ
БББББББББББББББ
5 - 36
ERROR REMEDY
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change COM command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change SD command.
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
* Change corresponding parameter.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding parameter.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change EOF command.
БББББББББББББББ
БББББББББББББББ
* Change EOF command.
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
WAIT instruction: There is no comma (,") or the bracket is not closed [)"] after the sec
БББББББББББББББ
ond parameter.
БББББББББББББББ
БББББББББББББББ
WAIT instruction: The third parameter is not a standalone variable.
БББББББББББББББ
БББББББББББББББ
AXP instruction: The first parameter is not of
БББББББББББББББ
the type Integer".
БББББББББББББББ
AXP instruction: There is no comma (,") after
БББББББББББББББ
the first parameter.
БББББББББББББББ
AXP instruction: The second parameter is not
БББББББББББББББ
of the type Integer", Real" or Doublepreci
БББББББББББББББ
sion real".
БББББББББББББББ
AXP instruction: There is something else as
БББББББББББББББ
well as AXPs in the list enclosed by square
БББББББББББББББ
brackets, e.g.: [AXP (1,100) ,A].
БББББББББББББББ
AXP instruction: AXP is programmed in a vari
БББББББББББББББ
able address, e.g.: X[AXP (1,1000) ].
БББББББББББББББ
ERROR REMEDY
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change WAIT instruction.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
2185 MULTIPLE SUBROUTINE PROHIBITED
БББББББББББББББ
More than one subroutine call is programmed
БББББББББББББББ
in the NC block.
БББББББББББББББ
2186 INVALID PERMVARIABLE
A permanent variable was programmed with
БББББББББББББББ
more than 2 digits; however, only permanent
БББББББББББББББ
variables from 0..99 are possible.
БББББББББББББББ
The permanent variable does not start with a
БББББББББББББББ
digit.
БББББББББББББББ
The permanent variable is of the type
БББББББББББББББ
Doubleprecision real", String" or Bool
БББББББББББББББ
ean".
БББББББББББББББ
БББББББББББББББ
The permanent variable is not of the type In teger" or it is a field variable.
БББББББББББББББ
БББББББББББББББ
The number of the permanent variable (first
БББББББББББББББ
and second digits after the @") is greater than 50.
БББББББББББББББ
2187 " MISSING
БББББББББББББББ
The final '  ' of a string constant is missing.
БББББББББББББББ
5 - 37
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Check and correct permanent variables.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change permanent variable.
БББББББББББББББ
БББББББББББББББ
* Change type of permanent variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change permanent variable.
БББББББББББББББ
БББББББББББББББ
* Change permanent variable.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change string constant.
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2188 PARAMETER ERROR
The directory is not TTY" and no length is
БББББББББББББББ
programmed for the OPENW command.
БББББББББББББББ
БББББББББББББББ
A subroutine with more variables than de clared in the subroutine is called in the main
БББББББББББББББ
program of DA mode.
БББББББББББББББ
БББББББББББББББ
A parameter of a current parameter list does not exist, e.g. P5" (for 5th parameter), in the
БББББББББББББББ
calling subroutine.
БББББББББББББББ
БББББББББББББББ
No comma (,") follows the logical number for the OPENR or OPENW command.
БББББББББББББББ
БББББББББББББББ
No comma (,") follows the file No. for the
БББББББББББББББ
OPENW command.
БББББББББББББББ
2189 INVALID LABEL
A ." is recognized as a label which does not
БББББББББББББББ
start with a letter.
БББББББББББББББ
2190 ERROR IN NC BLOCK
БББББББББББББББ
If one of the address letters I, J, K, F is mis sing in G993 of the oscillating axis.
БББББББББББББББ
БББББББББББББББ
The format of the G, M or auxiliary function
БББББББББББББББ
word (machine parameter P9000) is not per mitted.
БББББББББББББББ
БББББББББББББББ
An auxiliary function with transferstop is pro
БББББББББББББББ
grammed alongside G92.
БББББББББББББББ
No line feed follows the M2 or M30 word (ex
БББББББББББББББ
cept for blanks).
БББББББББББББББ
БББББББББББББББ
The NC block has more than 128 characters or it does not end with a line feed at the file
БББББББББББББББ
end.
БББББББББББББББ
БББББББББББББББ
In axis coupling", the address programmed is not that of a slave axis (MPP124/2 or
БББББББББББББББ
124/4).
БББББББББББББББ
5 - 38
ERROR REMEDY
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check and correct number of transfer para
meters.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change parameter list or subroutine.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change corresponding command.
БББББББББББББББ
БББББББББББББББ
* Change OPENW command.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change part program.
БББББББББББББББ
БББББББББББББББ
* Change corresponding NC word.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
Two of the following NC words are pro grammed in one block: G70, G71, G75, G33
БББББББББББББББ
or G92.
БББББББББББББББ
БББББББББББББББ
A G subroutine call is not the last Gword in a block.
БББББББББББББББ
БББББББББББББББ
The M subroutine call is not the last Mword
БББББББББББББББ
in a block.
БББББББББББББББ
An auxiliary function subroutine call is not the
БББББББББББББББ
last corresponding auxiliary function word in
БББББББББББББББ
a block.
БББББББББББББББ
There is no address letter before a [" in the
БББББББББББББББ
NC block and it is not a parameter list (no
БББББББББББББББ
subroutine call in the NC block) and it is not an AXP instruction.
БББББББББББББББ
БББББББББББББББ
G491 programmed together with other G
БББББББББББББББ
codes.
БББББББББББББББ
Address C" is programmed with active
БББББББББББББББ
G491.
БББББББББББББББ
G491 is programmed with nonactive Caxis.
БББББББББББББББ
БББББББББББББББ
A faulty NC block was discovered during the
БББББББББББББББ
syntax check for DA operation.
БББББББББББББББ
Moving through turning centre while machin
БББББББББББББББ
ing face end.
БББББББББББББББ
2191 DIVISION BY 0
БББББББББББББББ
CPL division /" by zero exists. If CPL division is not involved, then there is an
БББББББББББББББ
internal software error.
БББББББББББББББ
2193 INVALID TAN
БББББББББББББББ
Tangent calculation of 90 degrees, -90 de grees.
БББББББББББББББ
БББББББББББББББ
2194 INVALID ASIN ACOS
For calculation of the arc sin or arc cos of a
БББББББББББББББ
value outside the value range.
БББББББББББББББ
2195 NEGATIVE ROOT
БББББББББББББББ
Root calculation of a negative number. Argu ment for root calculation is negative.
БББББББББББББББ
БББББББББББББББ
5 - 39
ERROR REMEDY
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Program G491 in a single block.
БББББББББББББББ
БББББББББББББББ
* Avoid C" address.
БББББББББББББББ
БББББББББББББББ
* Program G491 with active Caxis.
БББББББББББББББ
БББББББББББББББ
* Change NC block.
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check CPL program. * Inform aftersales service.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Calculate only values which are not 90 or -90.
БББББББББББББББ
БББББББББББББББ
* Observe value range: -1 ... 1
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Only positive values permitted
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2196 INVALID REAL VALUE
Occurs for the ROUND or INT command if the
БББББББББББББББ
REAL value to be processed is outside the
БББББББББББББББ
value range.
БББББББББББББББ
An overflow has occurred in conversion of a
БББББББББББББББ
doubleprecision real number into a single
БББББББББББББББ
real number.
БББББББББББББББ
Result of the root calculation is too large.
БББББББББББББББ
With coordinate transformation switched on,
БББББББББББББББ
turning a programmed position causes a
БББББББББББББББ
REAL overflow.
БББББББББББББББ
2197 PROHIB. WORKING AREA
The programmed end point is in the pro
БББББББББББББББ
hibited working area.
БББББББББББББББ
2210 ENDDLG MISSING
БББББББББББББББ
There is a second DLG without the first hav ing been terminated by ENDDLG.
БББББББББББББББ
БББББББББББББББ
The corresponding ENDDLG is missing for a
БББББББББББББББ
DLG in a subroutine.
БББББББББББББББ
2211 DLG MISSING
There is an ENDDLG without a DLG.
БББББББББББББББ
БББББББББББББББ
There is a PRN command with fourth para
БББББББББББББББ
meter outside a DLG sequence.
БББББББББББББББ
An INP command has been recognized out
БББББББББББББББ
side a DLG sequence.
БББББББББББББББ
ERROR REMEDY
* Observe value range of the REAL value
БББББББББББББББ
2147483648 ..2147483647.
БББББББББББББББ
Check CPL program.
БББББББББББББББ
* Only positive values permitted.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change NC program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Check program.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
* Change CPL program.
БББББББББББББББ
БББББББББББББББ
2212 WRONG INPUT FORMAT
БББББББББББББББ
The opening bracket after the INP command is missing.
БББББББББББББББ
БББББББББББББББ
The parameter of the INP command is not a
БББББББББББББББ
variable and not a field variable.
БББББББББББББББ
The closing bracket of the INP command is
БББББББББББББББ
missing.7
БББББББББББББББ
5 - 40
БББББББББББББББ
* Change INP command.
БББББББББББББББ
БББББББББББББББ
* Change INP command.
БББББББББББББББ
БББББББББББББББ
* Change INP command.
БББББББББББББББ
БББББББББББББББ
Flexible Automation
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Runtime errors
CC 220 / 320
Error messages
ERROR CAUSE
2213 WRONG PRINT FORMAT
GPR command: The first parameter is less
БББББББББББББББ
than 0 or greater than 511, or the second
БББББББББББББББ
parameter is less than 0 or greater than 350.
БББББББББББББББ
DSP command: A parameter is not one of the
БББББББББББББББ
type Integer", Real , String" or Boolean".
БББББББББББББББ
БББББББББББББББ
PRN command: The first parameter is less than 4 or greater than 42 or the second para
БББББББББББББББ
meter is less than 1 or greater than 64.
БББББББББББББББ
БББББББББББББББ
PRN command: Opening bracket missing.
БББББББББББББББ
PRN command: The first or second para
БББББББББББББББ
meter is not of the type Integer" or  Real".
БББББББББББББББ
PRN command: There is no comma after the
БББББББББББББББ
first or second parameter.
БББББББББББББББ
БББББББББББББББ
PRN command: The third parameter is not of the type String".
БББББББББББББББ
БББББББББББББББ
PRN command: One of the two first para
БББББББББББББББ
meters is not an integer constant or the third parameter is not a string constant within the
БББББББББББББББ
DLG sequence.
БББББББББББББББ
БББББББББББББББ
PRN command: The fourth parameter is not a variable or field variable.
БББББББББББББББ
БББББББББББББББ
PRN command: No closing bracket follows
БББББББББББББББ
the third or fourth parameter.
БББББББББББББББ
PRN#(0..) command: Two commas are pro
БББББББББББББББ
grammed in sequence.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
5 - 41
ERROR REMEDY
* Change GPR command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change DSP command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
* Change PRN command.
БББББББББББББББ
БББББББББББББББ
* Change PRN#(0,..) command.
БББББББББББББББ
БББББББББББББББ
БББББББББББББББ
Loading...